Draw-Tite Accessories and Parts - 5506
- Works with all 2, 4, 6 and 8 Brake Systems
- Pilot (39518)
- Powertrac (39523)
- Reliance (47285)
- Activator (5100)
- Activator II (5500)
- Hand-held (5510)
- Activator III (5510)
- Journey (TM) (V52650)
- Journey HD (V52740)
- Odyssey II (TM)(32810)
- Voyager (39510)
- Primus (90155)
- Odyssey (52810)
- Energize III (81741B)
- Prodigy (90185)
- P-3 (90195)
- Includes:
- 25 ft. 10-2 Duplex Wire
- 30 Amp Circuit Breaker
- Attaching Terminals
5506 Draw-Tite Wiring Kit
Tow Ready #20506
Customers Who Purchased This Accessories and Parts Also Bought...
Ask the Experts about this Draw-Tite Accessories and Parts
Do you have a question about this Accessories and Parts?
- Troubleshooting Valley Journey HD Trailer Brake Controller SC Error Message
- The SC error code on the Valley Journey HD brake controller indicates that there is a short circuit situation. The trailer brake circuit (blue wire on the brake controller) may be shorted to ground. Since you have stated you recently replaced the brakes, it is possible that a ground wire came disconnected or was not connected during installation. I would check the grounds starting at the brake controller.
Next, I would move to the 7-Way trailer connector and make sure that it is grounded to t
view full answer...
- Location of Factory Trailer Brake Controller Harness on a 2007 Toyota Tacoma with Tow Package
- The factory harness to plug in a brake controller wiring harness on your 2007 Toyota Tacoma is located underneath and left of the steering column, taped to another harness near the emergency brake pedal. There
will be a 5-pin connector that mates with the one on the adapter, # 3040-P. The harness does include an additional ground (white) wire that will need to be attached to a bare metal surface.
If you need a brake controller, I recommend the Tekonsha Prodigy P2 with Wiring Harness, # 90885
view full answer...
- Location of Factory Brake Controller Wiring Harness on a 2009 Toyota Tacoma TRD with Tow Package
- The factory brake controller wiring harness on your 2009 Toyota Tacoma will be in one of two places. First, since you already have removed the interior left most floor panel, you can check there for the connector. It is pretty well hidden behind other harnesses and it could have fallen back or down even further. You will need to fish around in there to pull it out.
If you cannot find it there, then check to the right or left of the steering column (near the emergency brake pedal) up under the
view full answer...
- Parts Needed to Make a Brake Controller Portable Between a Toyota and a Jeep
- At this time we do not carry the vehicle side of the Brake Control Wiring Adapters for an installation application like you are suggesting. But, I do have a recommendation for you.
You could use a 12 inch Car and Trailer End Loop, item # 9653P, and wire the brake controller wiring to this. You would want to attach the vehicle side connector, 3 protected poles and exposed ground pole, to the vehicle and the trailer side to the wiring from the brake controller. You would then need another vehic
view full answer...
- Troubleshooting a 5E Error Message on a Hopkins Reliance Trailer Brake Controller
- I cannot find any information regarding a 5E or SE error message related to the Hopkins Reliance brake controller. The cause of the error depends on how it is affecting the performance of the brake controller. So I can go over some common issues which may be the problem.
First, you mentioned the red wire. On the cold side of the brake switch, there can be more than one wire that shows a signal when the brake pedal is pressed. If it is connected to a wire that also shows a signal when the head
view full answer...
- Location of Brake Controller Port on a 2003 Chevrolet Silverado 2500 HD
- If your 2003 Chevrolet Silverado 2500 HD has the factory installed hitch and a 7-Way connector, then all of the wires for the brake controller have been run. The factory brake controller port is located in the black box underneath the dash on the drivers side, to the left of the brake pedal. Usually a brake control adapter will be included in the junction box.
If an adapter is not in the junction box you can use the Draw-Tite Universal Brake Control Wiring Adapter, part # 20264, for Draw-Tit
view full answer...
- Troubleshooting an SC error code on Journey HD controller
- It sounds like you have an intermittent short circuit that is being caused a loose wire somewhere that sometimes makes good contact which explains why it works sometimes, and then when the contact is not good you see the SC code.
To eliminate the brake controller from the short circuit equation you will need to sever the blue brake output circuit wire and using a circuit tester like a # BTMT15 test for voltage on the circuit from the brake controller using the manual override lever. If the SC
view full answer...
- Brake Controller Wiring on a 1991 Jeep Cherokee
- The Jeeps are not pre-wired for brake controllers. The wires need to be run from the back of the Jeep (where the 7-way connector is) to the front and connected to the brake control box and the battery. Since your Jeep already has the 7-way in the rear who ever installed that may have run those extra wires up to the front. You will need to climb under the Jeep and follow the wires coming out of the 7-way plug. If the wires have already been run to the front you really will not need anything besid
view full answer...
- Electric Trailer Brake Controller Harness for a 2010 Toyota Tacoma with Factory Tow Package
- For your 2010 Toyota Tacoma, you can use the Tow Ready brake controller harness, part # 20265. Just color match the wires from the harness to the loose wires on your brake controller. White is the ground, blue is brake output, black is 12-volt hot lead, and red is the stop light switch. You can solder them together or use butt connectors. The plug is located underneath the dashboard, to the left of the steering column taped to another wiring harness near the emergency brake pedal. I have include
view full answer...
