Adapter 7 Way (Blade) to 7 Way (Round Pin)

Hopkins Wiring - 47595

Adapter converts 7 way (flat pin) wiring connector on your vehicle to 7 way (round pin) connector for trailers. The 7 way flat pin style is the most common 7 way connector that comes on many of the newer pickups.

• Dimensions:
  • Overall length: 12"
  • Distance between plugs: 4-1/2"

Customers compare 47595 to these similar products

Pollak Trailer Connector Adapter - Vehicle End - 7-Pole Round to 7-Pole Flat$24.95

Hopkins Endurance Multi-Tow Trailer Connector Adapter - 7-Way to 6-Way, 5-Way or 4-Way$21.95

Pollak Heavy-Duty, 7-Pole, Round Pin, Trailer Wiring Connector - Trailer End$8.99

Adapter 4 Pole to 7 Pole Vehicle End Trailer Connector$17.45

Pollak Black Plastic, 7-Pole, RV-Style Trailer Socket - Vehicle End$6.99

Customers Who Purchased This Wiring Also Bought...

Wire Frame Clip $0.17

Shackle Strap - 2-1/4" Long $0.70

Bonded 4 Wire - per foot $0.57

Wire - Jacketed 7-Wire - per Foot $2.07

Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot $1.21

Ask the Experts about this Hopkins Wiring
Do you have a question about this Wiring?

• Length Measurements of Adapter 7 Way Blade to 7 Way Round Pin, # 47595
  
• For Adapter 7 Way (Blade) to 7 Way (Round Pin), # 47595, the distance between the plugs is 4-1/2 inches. I measured from the back of one connector to the back of the other connector. Overall length is about 12 inches.
  view full answer...


• What Will The Center Pin Function Be On Hopkins 7-Way Blade To Round Pin Adapter
  
• Yes, the Adapter 7 Way (Blade) to 7 Way (Round Pin), will make the center pin the brake control function. Looking at the connector if it were mounted on the back of your vehicle, from the top 12 o clock position going clockwise would be the following, White for ground, Black for 12 volt power, Yellow for left brake and turn, Purple for reverse lights at the 6 o clock position, Green right brake and turn, Brown tail and running lights. I have linked pictures of the connector diagrams to s
  view full answer...


• Troubleshooting a 7-way Connector on a 1998 GMC Truck
  
• Traditionally 7 way vehicle connectors are wired as follows: 1:00 Black, 12 Volt Battery Power 3:00 Green, Right Turn and Brake 5:00 Blue, Brake Controller 7:00 White, Ground 9:00 Yellow, Left Turn and Brake 11:00 Brown, Tail and Running Lights Center Pole is usually a Purple wire that is run to reverse lights It sounds like your vehicle connector is wired by function correctly, but there could be a problem with some of the wiring at the connector. You are going to want to use a
  view full answer...


• Making a 7-Way to 9-Pole Trailer Adapter for a 1987 Avalon Trailer
  
• What you can do is make an adapter to go from the 7-Way on your vehicle to the 9-Way used on the trailer. You will only need two parts and some wire. First, you will need a Pollak Black Plastic 7-Way, Trailer Side, # PK12706. Then you will need Pollak 9-Pole, Round Pin Trailer Socket - Vehicle End, # PK12907. Both of these parts are designed so that you can attach the wires yourself. If you open up each one, you will see a number and function description next to each pin. All you will need to
  view full answer...


• Will Hopkins Trailer Connector Adapters Fit Pollak Trailer Connectors
  
• I went out to the warehouse and pulled a Hopkins Adapter 7 Way Blade to 7 Way Round Pin, # 47595, a Pollak Black Plastic, 7-Pole, RV-Style Trailer Socket, # PK12707, and a Pollak Heavy-Duty, 7-Pole, Round Pin, Trailer Wiring Connector, # PK11700. I tested fitted all of the parts together and they are compatible. I also made a short video showing how the parts work together.
  view full answer...


• How is the Adapter 7 Way Blade to 7 Way Round Pin # 47595 Configured
  
• I will be happy to tell you how the pins are configured on the Adapter # 47595. On the 7-Way blade side, if you are looking at the face of the plug: 1 oclock position = tail and running lights 3 oclock position = left turn and brake lights 5 oclock position = ground 7 oclock position = output to trailer brakes 9 oclock position = right turn and brake lights 11 oclock position = 12 volt power Center position = reverse lights/auxiliary circuit On the 7-Way Round pin side, if looking
  view full answer...


• Need Adapter for a 6-Way Round Pin on a 1968 Chevy C-50 to a 7-Way on a Trailer
  
• To go from a 6-Way round pin trailer connector on a vehicle to a 7-Way blade style connector on a trailer, you will need to use adapter # 47435. A 6-Way can be wired in 2 different ways, the brake out put could be the center pin or the 12 volt could be the center pin. You may need to re-pin the adapter to match your set up.
  view full answer...


• Adapter for Trailer with 7-Way Round Connector and 2012 Honda Ridgeline with 7-Way Blade Connector
  
• It sounds like the connector on the boat is an adapted 4-Way to use with a 7-Way round pin trailer connector on a vehicle. That would be why there are just 4 pins, 3 for the lighting functions and 1 for ground. If that is the case then the 7-Way blade to 7-Way round adapter, # 47595 should work just fine. Most boat trailers have the basic lighting functions but do not have the components that require the other circuits such as 12 volt accessory power and electric brakes.
  view full answer...


• Will Hopkins 7 Way Blade to 7 Way Round Adapter # 47595 Work with 2001 Ford F-350 and Camper
  
• Based on the information you have provided, I see no reason why the Hopkins 7 Way Blade to 7 Way Round Adapter # 47595 would not work. Another option would be to remove the 7-way round pin connector from your camper and replacing it with the Hopkins Endurance 7-Way Trailer Connect # HM48500. The mounting bracket, hardware, and grease packet are included and I have provided a link to the installation instructions for this product as well. Regarding your question about a cover for your campe
  view full answer...


• 7 Foot 7-Way Extension and 7-Way Blade to 7-Way Round Adapter Recommendation for 1992 Lance Camper
  
• I believe I have a solution for you. For a 7 foot extension you would want a Curt Universal 5th Wheel/Gooseneck 7-Way Extension # C56080. This is a blade style connector so it will plug into the 7-way at the rear of your 2006 Dodge Ram 2500 that is 7 feet long and then you would use a Adapter 7 Way (Blade) to 7 Way (Round ) # 47595 that you referenced to convert it to the style connector you have on your trailer.
  view full answer...


• Color Clarification Regarding Wiring Issues of a 7 pin Trailer Blade Connector
  
• Figuring out what color wire goes to what function is sometimes quite confusing. I have attached a diagram which covers both the most common wire colors designated for a seven pin trailer connector and a seven pin vehicle connector, referencing the wiring colors for each blade and what each blade is responsible for. If you look up part # H20046, you will see about 1/3 of the way down the page a chart that will give you a wiring guide. It gives you the color of the wire and how it relates to t
  view full answer...


• How to Wire Up a 6-Way on a Hawk Trailer
  
• Since trailer wires colors are not always consistent among manufacturers the best way to figure the functions of each circuit is to test each circuit individually. There are two ways you can do this, the easier way is to get a car battery and run a jumper wire from the positive side of the battery to each of the wires in question. When you put current on each circuit you should be able to see what functions activate, which will tell you what does what. I would recommend you label each circuit
  view full answer...