Plug-N-Tow (TM) Wiring Connector with Circuit Protection

Rating: rating rating rating rating rating
2 reviews

Code: 42535

Price:$49.95

Shipping Weight: 2 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Hopkins Custom Fit Vehicle Wiring - 42535

Plug-N-Tow Wiring Connectors provide a no-hassle, quick and easy way to wire your vehicle.

Each vehicle specific connector is pre-wired and uses original OEM connectors for water tight protection, a guaranteed fit, and a great look
No cutting or taping
16 gauge wire
4-Pole connector includes dust cap
Each kit includes everything needed to complete a 4-wire flat installation
Powered converter with circuit protection is included in a weatherproof double-molded design
- Circuit Protection guards the tow vehicle and the converter itself from trailer shorts

Jeep Grand Cherokee connection point is located by removing the driver's side panel in the rear.

Can be used with 5-pole, 6-pole or 7-pole adapters.

Replaces TAP #32535

This Product Fits The Following Vehicles

1999 - 2004 Jeep Grand Cherokee All Models

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Ball Mount 3/4" Rise or 2" Drop, 6,000 lbs $17.78

Pin and Clip For Class III, IV and V Trailer Hitch Receiver $4.99

Hitch Ball with 2" Diameter and Medium Shank, 6,000 lbs GTW - Chrome $8.49

Customer Reviews - Write a review about this product

Plug-N-Tow TM Wiring Connector with Circuit Protection - 42535

Average Customer Rating: rating rating rating rating rating 4.5 out of 5 stars (2 Customer Reviews)

Plug-N-Tow TM Wiring Connector with Circuit Protection - 42535

rating rating rating rating rating by: Paul M08/08/2011

Is this review helpful?

Plug-n-tow wiring connector was easy to connect, Not too bad to route. Could use a little more length. Curt hitch install video was excellent, made it look easy. The bolt at the gas tank strap was a pain and had to get special 18mm socket. Had everything but in my toolbox! Nice product still. 21379

Plug-N-Tow TM Wiring Connector with Circuit Protection - 42535

rating rating rating rating rating by: tom bowman05/11/2011

Is this review helpful?

quick and easy installation. Quick ship ping13595

Ask the Experts about this Hopkins Custom Fit Vehicle Wiring
Expert Answers about Plug-N-Tow (TM) Wiring Connector with Circuit Protection - 42535 Do you have a question about this Custom Fit Vehicle Wiring?

Permanently Mounting a Plug-N-Tow Wiring Connector Outside the Vehicle
The Plug-N-Tow TM Wiring Connector with Circuit Protection, part # 42535, connects to a port located under a panel in the rear of the vehicle on the driver side. Most people will leave the connector in the back of their Jeep until they need to use it, and then just pull it out the back door. If you want to route the connector out for a permanent outer mounting application, usually a rubber grommet can be found in the same area as the port. You can cut a slit in the grommet, pass the connector th
view full answer...

Wiring Harness Connection Point on a 1999 Jeep Grand Cherokee
We have a video of a wiring harness installation on the 1999 Jeep Grand Cherokee for you to review. The video shows exactly where to find the connection point and which rear panel to remove to get to it.
view full answer...

How to Install Hopkins Plug-N-Tow Wiring Connector 42535 on a 2000 Jeep Grand Cherokee
We do not currently have an video demonstrating the installation of the # 42535 on a 2000 Jeep Grand Cherokee, but the installation process is pretty straight forward. The install on your vehicle would go as follows: 1. You will locate your vehicle taillight wiring harness. This harness will have the same connector end as the # 42535 connector, and will be located by removing the driver side panel in the rear of the vehicle. 2. Remove protective cap from the vehicle taillight wiring harn
view full answer...

Is An Extension Harness Available For The Hopkins Plug-N-Tow Wiring Connector # 42535
I do have the Hopkins 48 Inch Long 4-Pole Loop with Cover # HM47115 which is a 4 foot extension that you can use to add length to your 4-way connector.
view full answer...