See What Fits Your Vehicle
customer service | view cart  View Cart

Trailer Brakes > Hydraulic Drum Brakes > Brake Assemblies > 10 x 2-1/4 Inch > 3500 lbs Axle > Right Hand Side > Free Backing > Redline

40715

Galvanized 10" Marine Brake Assembly, Free Backing, Right Hand

Redline Trailer Brakes

Rating: ratingratingratingratingrating
2 reviews


Code:   40715

Retail:$74.54

Price:$69.95

Shipping Weight: 11 pounds

Shipping Special
Quantity: 




Redline Trailer Brakes - 40715

Demco Free Backing 10" x 2-1/4" Galvanized Hydraulic Brake Assembly for Boat Trailers
Features:
  • Galvanized backing plates
  • Stainless steel spring hardware
  • Plated wheel cylinders
  • Riveted marine brake shoes
  • Works great on non-marine applications too
Specs
  • 3,500 lbs. Capacity per Pair
  • Right Hand - Passenger Side
  • Free-Backing - incorporates a "fall-away" shoe which diminishes shoe drag when backing up
    • Minimal Braking in reverse
  • Uses 10" Hub/Drums - Wheel Size 13" - 15"
  • Requires periodic manual adjusting



Video of Galvanized 10" Marine Brake Assembly, Free Backing, Right Hand


Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video Demo Redline Trailer Brakes 40715
Redline Galvanized 10" Right Hand Trailer Brakes Review

Video Transcript for Redline Galvanized 10" Right Hand Trailer Brakes Review

Today were looking at the Demco 10 inch marine brake assembly, part number 40715. This is the right hand side and the way we tell this is by looking at the brake shoe linings. The forward shoe will be smaller than the rear shoe or primary shoe. This is our single servo setup which means the wheel cylinder will have piston that will push out against the brake shoe creating a wedge effect inside the brake drum. This assembly mounts on a 4 bolt flange which is already pre drilled in the backing plate to sit on top of your 4 bolt flange studs. As initial setup, we use a star wheel adjuster to adjust the brake shoe linings out to create a light drag on the brake drum, then as the brake shoe linings wear, we can remove the grommet in the backing plate to adjust the star wheel out to keep that nice even braking.

When we couple the right hand side with the left hand side, we can create up to 3500 pounds in braking capacity. To measure our brake shoe assembly, we go from the width of the brake shoe lining to the other brake shoe lining and see we have 10 inches and then we can measure the thickness of the brake shoe which is 2 and . This assembly will fit a 10 inch by 2 inch hub drum assembly. This assembly is also set on a galvanized backing plate making it goof for marine applications. It also a fall away brake system which means there will be minimal drag when backing up making it a good application for trailers with braking couplers.

There you have it for the Demco 10 inch marine brake assembly part 40715.






Customers Who Purchased This Trailer Brakes Also Bought...






Customer Reviews  -  Write a review about this product

Galvanized 10 - 40715

Average Customer Rating:  ratingratingratingratingrating5.0 out of 5 stars   (2 Customer Reviews)




Galvanized 10 - 40715

ratingratingratingratingrating by: Scott C.12/02/2011

Is this review helpful?


Product arrived promptly, exactly as described and of good quality. Will continue to purchase items from etrailer. Excellent service.27547



Galvanized 10 - 40715

ratingratingratingratingrating by: Williams Dave07/10/2011

Is this review helpful?


You have exceded my ecpectations with your great resoponse and speedey service .I will use your service again and highly recomend etrailer to all my friends Thank you 19037




Ask the Experts about this Redline Trailer Brakes
Expert Answers about Galvanized 10" Marine Brake Assembly, Free Backing, Right Hand - 40715                                             Do you have a question about this Trailer Brakes?


  • What Braking Assemblies do I Need for Karavan Tandem Axle
  • If the bolt pattern on your axles, for the backing plate, is 2-3/4 inch on center , both of these braking assemblies would fit your 10 inch x 2-1/4 inch trailer brake assemblies. Part # 40715 and # 40716 are what I would recommend. These are the left and right hand side brake assemblies. Since you are going to be backing up an incline you want the least amount of reverse braking which is why I recommend these over the other. The shoes for these assemblies are part # BP04-126. The part incl
    view full answer...

  • What Information is Need to Find Parts to Switch from Hydraulic to Electric Drum Brakes
  • We would need to know how big the current brakes are. 10x2-1/4 or 12x2 etc. Sometimes you can re-use the drums from hydraulic brakes for electric brakes, sometimes not. If you are going to go ahead and replace the drums, we would need to know inner and outer bearing numbers. These are stamped right on the bearings. We would also need the bolt pattern of the drums. I have added a link to a wheel page that shows you how to measure bolt pattern at the bottom. Wheel diameter is important as well,
    view full answer...






Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email




etrailer.com reviews etrailer.com reviews

All images, layout and content copyright etrailer.com