Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4"

Draw-Tite Trailer Hitch - 36216

This fully welded, corrosion-resistant vehicle trailer hitch is perfect for your light-duty towing and hitch rack needs. Tested Tough guarantee ensures that this hitch exceeds industry strength standards. Drawbar, pin and clip sold separately.

Features:

• Custom fit is designed specifically for your vehicle
• Computer-aided, fully welded steel construction ensures strength and durability
• Tested Tough - safety and reliability criteria exceed industry standards
• Bolt-on installation - no welding required
  • Complete hardware kit and installation instructions included
• Lifetime technical support from the experts at etrailer.com
• Black powder coat finish covers e-coat base for superior rust protection
• Sturdy, square-tube design
• Drawbar, pin and clip are sold separately
• Made in USA

Specs:

• Receiver opening: 1-1/4" x 1-1/4"
• Rating: Class II
  • Maximum gross trailer weight: 3,500 lbs
  • Maximum tongue weight: 300 lbs
• Limited lifetime warranty

Draw-Tite Tested Tough

Draw-Tite's Tested Tough program provides testing standards far superior to those outlined by the Society of Automotive Engineers (SAE), the go-to source for engineering professionals.

Each Draw-Tite trailer hitch receiver undergoes extensive fatigue testing and static testing with the ball mount that is either supplied or recommended for use with that particular hitch, thus ensuring results that are applicable to real life use. Fatigue testing is also conducted on hitches rated for use with weight-distribution systems.

In addition, Draw-Tite performs static testing on a simulated automobile, as opposed to the rigid fixture used for SAE testing, resulting in a more true-to-life scenario.

etrailer.com Technical Support

At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.

36216 Draw-Tite Class 2 Trailer Hitch Receiver

This Product Fits The Following Vehicles

1992 - 1995 Oldsmobile Delta 88

1992 - 1995 Oldsmobile LSS

1992 - 1995 Oldsmobile Royale

1992 - 1995 Pontiac Bonneville All Models except SSE and SSEi

1992 - 1999 Buick LeSabre FWD

Customers Who Purchased This Trailer Hitch Also Bought...

Ask the Experts about this Draw-Tite Trailer Hitch
Do you have a question about this Trailer Hitch?

• Trailer Hitch for a 1994 Pontiac Bonneville SSE
  
• We offer a hitch that would fit your 1994 Pontiac Bonneville SSE. The Draw-Tite Class II Receiver Hitch, part # 36216 is custom designed for your vehicle. With this hitch, the manufacturer recommends the Class II draw bar, part # 36061. You will need a pin and clip, part # PC2 to secure the draw bar into the receiver, or a locking hitch pin, part # 40106. If you need a trailer ball, we offer the 2 inch ball, part # 19258 or the 1-7/8 inch ball, part # 19256. To wire your Bonneville for towing,
  view full answer...


• Motorcycle Carrier Recommendation for a 1998 Buick LeSabre with a 1-1/4 In Trailer Hitch
  
• Your suspicions about too much weight far beyond the rear axle are correct. That much weight (a motorcycle carrier and dirt bike) would produce too much torque and could damage the vehicle. Adding a hitch expander to accept a 2 inch accessory on a 1-1/4 inch hitch will also reduce the tongue weight capacity of the hitch by 50 percent. But there is still an option. You could use a class II trailer hitch, like # 36216, and then use Hitch Mounted Motorcycle Caddy, # RHMC1. For this carrier to be
  view full answer...