Class II Drawbar 5/8" Rise or 1-1/4" Drop (Kit)

Draw-Tite Ball Mounts - 36051

• Fits 1-1/4" x 1-1/4" Class II receiver-style hitches
• Uses ball with 3/4" shank diameter
• Measures 7" long from center of pin hole to center of ball hole
• Ball mount provides 5/8" rise or 1-1/4" drop from top of your hitch's receiver tube
• Rated for up to 3,500 lbs gross trailer weight and up to 300 lbs tongue weight
• Includes pin and clip

Customers compare 36051 to these similar products

Ball Mount 3/4" Rise or 2" Drop, 7,500 lbs$17.20

Class II Drawbar 5/8" Rise or 1-1/4" Drop (Kit)$22.95

Class II Drawbar 3-1/8" Rise (Kit)$22.95

Customers Who Purchased This Ball Mounts Also Bought...

Hitch Ball with 2" Diameter and Short Shank, 3,500 lbs GTW - Chrome $6.49

Hitch Ball with 1-7/8" Diameter and Short Shank, 2000 lbs GTW - Chrome $6.49

Rubber Tube Cover 1-1/4" $4.49

American Flag 1-1/4" Trailer Hitch Receiver Cover $14.95

Hitch Ball Cover for 1-7/8" and 2" Diameter Hitch Balls $2.64

Ask the Experts about this Draw-Tite Ball Mounts
Do you have a question about this Ball Mounts?

• Everything Needed for a 2005 Hyundai Tucson to Tow a Trailer
  
• You will need five separate parts to tow a trailer with your 2005 Hyundai Tuscon. You will need a trailer hitch, a ballmount, a pin & clip, a hitch ball, and a wiring harness. You have 7 different hitch options for your Tuscon. I would recommend purchasing and installing a hitch with a 2 inch receiver opening over a smaller 1-1/4 inch hitch opening; the larger hitch will give you a lot more options for accessories. Also, we happen to have a very competitively priced Curt Class III Trailer Hitch
  view full answer...


• The Correct Drawbar for a 2003 Volkswagen Jetta with a Class I Hitch
  
• For your 2003 VW Jetta, the drawbar, # 36051, will not work because Class II accessories are designed with a feature that keeps them from being used in a lower class hitch. So you will need to use the Sportframe Drawbar, # 3593, instead. I pulled all the recommended hitches for your vehicle and this is the drawbar that is recommended as the proper fit for those hitches. There is not, necessarily, a recommended length. The limiting factor is the gross trailer weight and tongue weight capacity. In
  view full answer...


• What is the Correct Ball Mount for a Class II Trailer Hitch on a 2012 Ford Escape
  
• On Class I and Class II trailer hitches with a 1-1/4 inch receiver, you must use the ball mount specified by the trailer hitch manufacturer. The hitches have only been tested with those specific ball mounts and the use of any other ball mount will void the trailer hitch warranty. If it is a factory hitch, you can ask the dealer the brand of hitch and if there is a certain ball mount to use. If you are getting a Hidden Hitch trailer hitch, # 90108, or a Curt trailer hitch, # 12060, for your E
  view full answer...


• Class II Ball Mount Recommendation for a 2005 Chevy Equinox
  
• The recommended Class II ball mount for your 2005 Chevy Equinox is the Class II Drawbar # 36051 that you referenced. You might also be interested in the following products to complete your towing setup: Hitch Ball with 2 inch Diameter # 19258 Hitch Ball with 1-78 inch Diameter # 19256 DeadBolt Hitch Lock # 7682 (review video attached)
  view full answer...