Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"

Curt Front Hitch - 31055

Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.

Features:

• Front-mount hitch provides attachment point for hitch-mounted accessories
  • Winch, spare tire carrier, snowplow, cargo carrier and more
  • No more blindly backing trailer in - just hook it up and drive it forward
• Custom fit is designed specifically for your vehicle
• Precision, robotic welding maximizes strength and improves fit
• Easy, bolt-on installation - no welding required
  • Complete hardware kit and installation instructions included
• Lifetime technical support from the experts at etrailer.com
• Gloss black powder coat finish over steel resists corrosion
• Sturdy, square-tube design
• Made in USA

Specs:

• Line pull: 9,000 lbs
• Vertical load: 350 lbs
• Gross trailer weight: 3,500 lbs
• Receiver opening: 2" x 2"
• Pin hole diameter: 5/8"
• Limited lifetime warranty

etrailer.com Technical Support

At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.

31055 Curt Front-Mount Trailer Hitch Receiver

This Product Fits The Following Vehicles

2002 - 2008 GMC Envoy

2004 - 2006 Buick Rainier

2002 - 2008 Chevrolet TrailBlazer

Customers Who Purchased This Front Hitch Also Bought...

Ask the Experts about this Curt Front Hitch

• Will Curt Front Mount Hitch Part # 31055 Fit the 2006 Chevrolet Trailblazer SS Without Trimming
  
• I spoke with my contact at Curt, and they have not had a chance to test fit the front mount hitch on an SS model. Frame should be the same between the SS and other models, but the SS front fascia is much different so it may require some fascia trimming, but they do not know where since they have not had a chance to fit one yet. The radiator may also be different or larger since the SS model got the 6.0 LS2 V8, a larger, higher output V8 than what came in the other V8 Trailblazer models. We
  view full answer...


• Recommend Front Mount Trailer Hitch and Spare Tire Carrier for 1997 Ford F-250 Diesel 2WD
  
• For a front mount receiver for your 1997 Ford F-250 2WD Diesel, we have the Draw-Tite Front Mount Hitch, part # 65014. This front receiver is designed to fit the 2-wheel drive diesel F-250. We do offer a Hitch Mounted Spare Tire Carrier from CURT. Checkout the Hitch Mounted Spare Tire Carrier # C31006. This spare tire carrier will work with 2 inch receivers like the Draw-Tite # 65014. To secure the spare tire carrier to the hitch you will need Pin and Clip, part # PC3. For a more secure op
  view full answer...


• Details on Fascia Trimming Required to Install a CURT Front Mount Trailer Hitch, 2008 GMC Envoy
  
• The CURT Front Mount Trailer Hitch, # 31055, is the correct front hitch for a 2008 GMC Envoy. We have not yet had the opportunity to install this hitch on a vehicle so I do not have a video or pictures I could link you to. But I have included a link to the installation details that show the trimming that needs to be done. There is a diagram that shows where and how much of the underbody trim panel that needs to be trimmed. It is about a 2-1/2 inch square area that only needs to be trimmed if
  view full answer...


• Is there a Video that Shows How to Perform the Fishwire Technique to Install a Trailer Hitch
  
• The CURT Front Mount Receiver, # 31055, does bolt to the vehicle frame rails but the bolts do not go all the way through each frame rail. Instead, like you have said, you will fishwire the hardware into the inside of each frame rail through access holes in the frame. The fishwire technique is not as difficult as you might think. Even though I do not have a video showing the hitch being installed on a 2006 GMC Envoy, I can provide a link that explains and shows how to fishwire hardware. I have
  view full answer...