Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury

Tekonsha Accessories and Parts - 3035-P

Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.

Features:

• Wiring adapter eases installation of your electric brake controller
• Custom connector end plugs into the built-in port beneath the dash of your vehicle
• Other end plugs into the back of your electric brake controller
  • Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
  • Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
• Limited 1-year warranty

Installation of Tekonsha Brake Controller Adapter

For most applications, the factory plug is located beneath the dash, near the center console. If you have a Ford full-size van, the harness is underneath and to the left of the steering column. The Ford Explorer and Mercury Mountaineer have 6-pin connectors behind the glove box on the passenger's side.

To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.

This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.

3035-P Tekonsha Brake Control Wiring Adapter with 2 Plugs

Video of Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury

Customers Who Purchased This Accessories and Parts Also Bought...

Ask the Experts about this Tekonsha Accessories and Parts
Do you have a question about this Accessories and Parts?

• Location of the Brake Controller Port for 2004 Ford Explorer with Tow Package
  
• On a 2004 Explorer with the newer body, the port is behind the glove box on the left side. You will open the glove box, push in the two tabs it rests on to get it to open further and the connector is buried on the left hand side, close to the center console. The port is located above the pedals for F-150/Expedition or larger Ford Trucks and SUVs.
  view full answer...


• Location of Brake Controller Port on 2001 Ford Expedition
  
• The female port for this part should be located underneath the dash close to or behind the center console, it is gray in color. It should be very close to the OBDII diagnostic port, the large trapezoidal shape plug by the center console underneath the dash. I spoke with one of our installers and he said it should be within a 6 inch radius of that OBDII port. We have a video on a 2007 Expedition, but you said you have searched our site so I assume you have seen it. I will include a link in ca
  view full answer...


• Brake Controller Wiring Harness For a 2009 Ford F-150 Pickup
  
• The Brake Control Wiring Adapter for Ford F-150 - 2 Plugs, item # 22292, is the wiring harness you will need for installation of a Tekonsha Prodigy P2- # 90885, Tekonsha P3 - # 90195 or a Draw-Tite Activator III - # 5520. If you need a harness to wire a brake controller which is hard wired you will need the Brake Controller Wiring Adapter for Ford F-150, item # 20272. The Tekonsha Wire Replacement for Ford Vehicles, item # 3035-P, is for older Ford models and will not work on the 2009 mode
  view full answer...


• Installing a Tekonsha P3 Brake Controller on a 2008 Ford F-450 with a Factory Brake Controller
  
• You should not have a problem installing the Tekonsha P3 Proportional Brake Controller with Ford Super Duty Adapter, item 90195-3034P, in your F-450 truck. This item number comes with the vehicle specific wiring connector for your truck. The biggest problem is that when removing your factory brake controller you will get a fault code on the dash that will not go away until you take the truck to the dealer and have the PCM (Power-Train Control Module) flashed so that the vehicle does not look for
  view full answer...


• Wiring Harness for Installation of the Voyager 9030 Brake Controller on a 2006 Ford F-150
  
• You will need the Universal Brake Control Wiring Adapter Ford, Land Rover, Lincoln, Mercury, item # 20260, to install the Tekonsha Voyager 9030 Brake Controller, item # 39510, on your 2006 Ford F-150. You will just have to splice the like colored wires from the Voyager to the harness with the included butt connectors. I have linked instructions for the Voyager in case you would like to review them before setting the controller up on your new vehicle.
  view full answer...


• Hardwiring a Brake Controller from Scratch on a 2010 Ford Flex
  
• On the 2010 Ford Flex, you will have to hardwire a brake controller. There are 3 items you will need to complete installation. First is a brake controller, second is the Tow Ready Custom Fit Vehicle Wiring, # 118472, and third is the 7 and 4 Way Installation Kit, # ETBC7. You will start by installing the Tow Ready Custom Fit Vehicle Wiring, # 118472. I have included a link to the installation details below. Installation is simple. The T-one harness plugs in line with your vehicles taillight w
  view full answer...


• Recommended Brake Controller for 1991 Ford F250
  
• Brake Controllers are not vehicle specific, you can use any controller you wish on your F250. This being said, I would recommend a proportional-type controller like the Tekonsha Prodigy, part # 90185. The Prodigy is our best selling brake controller, and is popular because it is easy to use and the initial set up is very simple. A proportional controller is superior to the older technology used by the time-delayed brake controllers. The proportional controller uses an internal sensor that can
  view full answer...


• Where is the Brake Controller Port Located on a 2010 Land Rover Range Rover Sport
  
• You should find your brake controller port underneath the dash somewhere in the center, somewhere above the brake pedal. You would find the port in this location on all Land Rover vehicles equipped with a port. It should be a gray colored plug that will have 6 pins/holes. There should only be 4 or 5 wires.
  view full answer...


• Blown Stop and Turn Signal Fuses After Installation of Prodigy Brake Controller 2004 Ford F150
  
• It sounds to me as if you may have a wiring harness that is pinned out improperly causing the fuse to blow. The first thing I would do is check the pin out diagram in the instructions (see link) and make sure your connector matches the diagram in the instructions. If it is improperly pinned you can change the pin out to the correct orientation using the instructions. If the connector is pinned out properly there may be an issue with the brake controller or vehicle wiring. Check out this
  view full answer...


• Where is the Brake Controller Port on a 2005 Ford E-350 Super Duty Diesel with Cut Away Box
  
• If your 2005 Ford E-350 has a factory 7-Way trailer connector, the brake controller harness, # 3035P, is the correct harness for numerous Tekonsha and Draw-Tite brake controllers. The port will be tucked up under the dash, to the left of the steering column. If your vehicle has a factory 4-Flat, you will need to add Adapter 4 Pole to 7 Pole and 4 Pole, # 37185, at the rear of the vehicle. The blue brake wire will need to be routed from the brake controller to the 37185 harness. The wires for
  view full answer...


• Can The Prodigy Brake Controller, # 90885, Be Installed In The Console On A 2009 Ford Flex
  
• Since your 2009 Ford Flex has the factory tow package and a factory 7-Way trailer connector at the rear of the vehicle the location of the brake controller plug is located under the dash, near the center console. There should be a open connector that will plug into the one end of the Tekonsha Wiring Adapter, # 3035-P, and the other end of the adapter will plug into the back of the brake controller. The Prodigy Brake Controller, # 90885, can be mounted in a 360 degree vertical range. So the mo
  view full answer...


• Location of Brake Controller Port Underneath Dash Of 2001 Ford Expedition
  
• I spoke with one of our installers and he informed me that the factory port you are looking for will be towards the center of the dash on the driver side. It will be located within 6 to 12 inches of the OBD II port. If you have the bottom panel removed on the driver side of the dash and are looking in and up towards the center of the dash you should be able to see the plug. It won't be hanging down, and may be tucked away behind some other wires. The color of the port should be gray. In addit
  view full answer...


• What Are the Correct Brake Controller Wiring Harness Adapters for a 2005 Ford F-350 Super Duty
  
• For a 2005 Ford F-350 Power Stroke, the correct brake controller wiring harness adapter for Tekonsha brake controllers is the Tekonsha Wire Replacement, # 3065-P. For Draw-Tite brake controllers, you would use # 20267. And for Hopkins you would need # HM47735. On the 2005 Ford F-350 Super Duty, the available brake controllers come with the specific wiring harness required to connect it to the port on the truck in the storage pocket, just above the ashtray and toward the center of the dashb
  view full answer...


• What Brake Controller Wiring Harness Is Needed For A 2005 Ford F350
  
• For your 2005 Ford F350 that has the factory installed brake controller port you will need the Tekonsha Wire Replacement for 2005-07 Ford Super Duty, # 3065-P. This will have a plug on one end that will plug into the factory brake controller port and the other end will plug into a Tekonsha brake controller. The Tekonsha Wiring Harness, # 3035-P, will not fit on your 2005 Ford F350. If you need a brake controller I would recommend the Tekonsha Prodigy P2 Brake Controller, # 90885. The Prod
  view full answer...


• What Is Needed To Add A Brake Controller To A 2003 Ford F-150 With Factory Tow Package
  
• The parts you will need to add a Tekonsha brake controller to your 2003 Ford F150 with factory tow package will depend on the trailer connector you have on your vehicle. If you have a factory 7-way connector on your vehicle, you will need the brake controller and the Tekonsha Wire Replacement Harness, # 3035-P. The # 3035-P will plug into your brake controller and the other end will plug into the factory brake controller port, which will be located under the dash near the center console on yo
  view full answer...


• Installing a Trailer Brake Controller on a 2011 Ford Escape with Factory Tow Package
  
• I spoke with my contact at Tekonsha about a brake controller wiring adapter for a 2011 Ford Escape with the Trailer Tow Package. He did not have specific information regarding the 2011 models, but historically the Ford Escape has been a hardwire only model. This means that you would first need a 4-Way wiring harness. With the factory tow package, you would use the Draw-Tite Custom Fit Vehicle Wiring, # 118251. Without a tow package, you would use the Tow Ready Custom Fit Vehicle Wiring, # 11
  view full answer...


• Brake Controller Wiring Adapter for 2010 Ford F150
  
• The Brake Controller Wiring Adapter, part # 22292 does carry over from the 2009 to the 2010 Ford F150 and is the correct wiring adapter for installing a Tekonsha P3 in your 2010 Ford F150. I will link you to the install instructions for the wiring adapter, as well as a link to an installation video that you might find helpful. The video shows a controller being installed on a 2009 F150, but the procedure on your 2010 model would be similar.
  view full answer...


• Which Wiring Harness Adapter Do I Need to Install A Prodigy Brake Controller on 2011 Ford F-450
  
• The wiring adapter that you will need for your 2011 Ford F-450 is the Tekonsha Wire Replacement for Ford Super Duty Pickups, part # 3034-P. For a brake controller, I would recommend the # 90195-3034P kit, which includes the wiring adapter and the brake controller unit. The Prodigy P3 can be used with electric trailer brakes and/or electric over hydraulic brakes. The P3 also has an LED display with 9 different color options and features diagnostic troubleshooting displays. I recommend the P3
  view full answer...


• What Is Needed to Install a Tekonsha P2 Electric Trailer Brake Controller on a 2010 Ford F-150
  
• The only parts you will need to install the Tekonsha P2 brake controller on your 2010 Ford F-150 with tow package are the brake controller itself and the correct wiring adapter. We sell these parts together as # 90885-22292. I have included the brake controller instructions and the wiring adapter instructions below. I have also included a video showing the harness being installed on a 2009 model which will be very similar to your 2010. The port to plug in the harness could also be up under the d
  view full answer...


• Installing Trailer Brake Controller on a 2006 Ford F-150 with Factory Installed Brake Controller
  
• According to our FAQ, which I have linked for reference, you only need to unplug the one connector that will be used with the Prodigy P2, # 90885. The plug that is needed will have matching wires with the brake controller adapter harness. The wiring should be labeled for function.
  view full answer...