Tekonsha Accessories and Parts - 3034-P
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.
Features:
- Wiring adapter eases installation of your electric brake controller
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
- Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
- Limited 1-year warranty
Installation of Tekonsha Brake Controller Adapter
This adapter plugs into the connector beneath your vehicle's dashboard. To reach the connector, first locate the notch in the access panel in the center of the dash, near the passenger side. Using a trim panel puller, carefully pry the panel out and undo the locking tabs to remove the panel. You will find the mating connector behind this portion of you dashboard.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
3034-P Tekonsha Brake Control Wiring Adapter with 2 Plugs
Customers Who Purchased This Accessories and Parts Also Bought...
Ask the Experts about this Tekonsha Accessories and Parts
- Does Factory Brake Control Need to be Removed to Install a New Brake Controller in a 2009 Ford F-350
- Your factory brake controller is actually using the same port that the # 3034-P brake control wiring harness will plug into, so you will need to remove the plug from the back side of the factory unit to install the Tekonsha controller, but you would not need to remove it completely.
Once you unplug the factory unit, you will get an error code in your dash. To remedy this, you can try removing the battery cable for three minutes and replacing it, but if this does not reset the error you will
view full answer...
- Will a Tekonsha Wire Harness for Ford Fit a 2010 Ford E-150 Cargo Van and Pilot Brake Controller
- If your 2010 Ford E-150 cargo van has the factory installed 7-Way connector at the rear of the van then all you will need is a brake controller and the Tekonsha Wire Replacement for Ford, item # 3034-P, that you selected to complete your installation. If your Reese Pilot controller has blunt cut wires coming out of the controller you can use the Brake Controller Wiring Adapter for Pre-Wired Ford Vehicles, item # 20270, which comes with blunt cut wires and butt-connectors to attach to your brake
view full answer...
- Setting Up a 2009 Ford E-350 Van without Factory Towing Package for Brake Controller Wiring
- There are 3 options from the manufacturer for the 2009 E-350 Ford Van. Factory 7-Way trailer wiring, factory 4-Way trailer wiring, and no existing trailer wiring. I will go over all three since you did not indicate which one your vehicle has.
If you have the factory 7-Way trailer wiring, you will be able to use the 3034-P wiring harness that you selected to easily install your prodigy brake controller. When looking for a port under the dash, it will be near the top of the instrument cluster,
view full answer...
Installation Details
