Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Rating: 
2 reviews
Code: 24734
Retail:$237.52
Price:$128.95
Shipping Weight: 38 pounds
Shipping SpecialThis fully welded, corrosion-resistant vehicle trailer hitch is perfect for your light-duty towing and hitch rack needs. Tested Tough guarantee ensures that this hitch exceeds industry strength standards. Drawbar, pin and clip sold separately.
Features:
Specs:
Draw-Tite's Tested Tough program provides testing standards far superior to those outlined by the Society of Automotive Engineers (SAE), the go-to source for engineering professionals.
Each Draw-Tite trailer hitch receiver undergoes extensive fatigue testing and static testing with the ball mount that is either supplied or recommended for use with that particular hitch, thus ensuring results that are applicable to real life use. Fatigue testing is also conducted on hitches rated for use with weight-distribution systems.
In addition, Draw-Tite performs static testing on a simulated automobile, as opposed to the rigid fixture used for SAE testing, resulting in a more true-to-life scenario.
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Video of Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Today on this 2006 Saturn Ion we are going to install part number 24734 from Draw-Tite. This also applies to part number 60989 from Hidden Hitch. Looking up at the passenger side of the vehicle the hitch is going to mount to the frame through this area right here. There are no existing holes for the hitch to attach to so we will end up drilling those out, using the hitch as a template. Now looking at the drivers side, the hitch will mount the same way as the passenger side, we will have to drill some holes in the frame to mount it up.
So one of our first steps is to lower the exhaust so you have more working room. You want to spray it down with some lubricant to help get it off a little easier. Okay, if we want, we can actually use a strap to pull it out of the way a little more. All right to get set up to drill our first hole, what we are going to do is actually measure from this edge here, find our center line, almost three inches. Alright we will just make sure with a ruler, back about 7/ 8ths inch. We will go ahead and mark it, and we will go ahead and drill out a pilot hole first and we will follow with a 1/ 2 inch drill bit.
Next we will go ahead and install our fish wire tool. Then we are going to install the bolt. That bolt is going to hold the hitch up so the rest of the holes can be drilled out. The hitch will act as a template. We will go all the way back to this access hole here, install our block, and then our bolt. And we will go ahead and hang our hitch from this one bolt. This is kind of an awkward part of the install so you want to have an extra set of hands to hold up one side of the hitch while install the hardware on the drivers side. And then we will find the center of the hole and mark it with a sharpie. And then we will drill out our holes. Alright we will go ahead and start threading our hardware back into the frame. On the bolt leader and out the access hole. Alright, back over to the drivers side.
Put the hitch back up, make sure you do not push the bolts back into the frame. And you will do just one side at a time. Alright, got the hitch is secured with two bolts. Now lets go ahead and finish off the other two bolts. These go on the passenger side here, then we will go back over to the drivers side. Okay we will go ahead and snug down the bolts. Lets go ahead and reattach our exhaust to the hanger. Have plenty of room there. The last thing to do is torque down the bolts as specified in the instructions. With that it finishes our install of part number 24734 from Draw-Tite.
2003 - 2003 Saturn Ion All Models
2004 - 2005 Saturn Ion All Models, except Red Line
2006 - 2007 Saturn Ion All Models, except Red Line and Models with 2.4 Liter Engine
Customers Who Purchased This Trailer Hitch Also Bought...
Average Customer Rating: 5.0 out of 5 stars (2 Customer Reviews)
by: Keith J.05/25/2011
Is this review helpful?
Be careful not to stretch coil on the fish wire it will lead to lots of unneeded cussing15345
by: Excellent09/12/2011
Is this review helpful?
Good product, Fits in perfectly (2004 Saturn ION). Note : YOU DO NOT NEED TO REMOVE THE EXHAUST RUBBER as shown in the video. Just leave the exhaust alone, it fits without it needing to be touched. I would also suggest tightening the first 2 nuts without the washer first then come back and put the washers on. 23854
Ask the Experts about this Draw-Tite Trailer Hitch
Do you have a question about this Trailer Hitch?
Installation Details
