T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Rating: rating rating rating rating rating
44 reviews

Code: 118450

Retail:$31.58

Price:$23.95

Shipping Weight: 1 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Trailer Wiring Harness Installation- 2010 Buick Enclave - Video
Trailer Wiring Harness Installation - 2009 Buick Enclave - Video
Trailer Wiring Harness Installation - 2010 Chevrolet Traverse - Video

Tow Ready Custom Fit Vehicle Wiring - 118450

Tow Ready T-One Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese

Provides a 4-pole flat trailer connector for the vehicle
Quick and Easy
No Cutting, Splicing or Taping
Just Plug in the T-One Connector and You're Ready to Tow
Solid One Piece Construction
16 Gauge Bonded Wire w/ 4-Flat Plug
"Factory" Appearance
Simple Do-It-Yourself Instructions on Every Package

Can be used with 5-pole, 6-pole or 7-pole adapters.

Installation: Connection points are located behind the vehicle taillights. The 4-pole trailer connector will be stowed under the vehicle close to the trailer hitch. A mounting bracket is recommended.

Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.

Warning:

Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:

Max. stop/turn light: (7.5 amps)
Max. tail lights: (7.5 amps)

Read vehicle's owners manual and instruction sheet for additional information.

Video of T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video Wiring Harness 2010 Buick Enclave 1

Trailer Wiring Harness Installation- 2010 Buick Enclave

Trailer Wiring Harness Installation - 2009 Buick Enclave

Video Wiring install 2010 Chevy Traverse

Trailer Wiring Harness Installation - 2010 Chevrolet Traverse

Video Transcript for Trailer Wiring Harness Installation- 2010 Buick Enclave

Today on this 2010 Buick Enclave we are going to be installing wiring harness part number 118450. We are at the rear cargo area of the Enclave, and we are going to locate the ports that we are going to be plugging our wiring harness into. These ports are actually located directly behind the tail light assembly on both the driver and passenger side. So, the first thing we want to do is remove both tail light assemblies. To do that we are going to open up the rear cargo door, there are two inboard screws holding the tail light into place. We need to pull back the covers to expose those. :30

With those two removed we just want to take and rock the tail light back and fourth, there are a couple outboard side clips that are holding it in place as well. With that pulled back, you can see the connector that we are going to be plugging our wiring harness in line to. What I am going to do at this time is disconnect the two, you can do that by pressing the tab at the top here and then pull the two pieces apart. Now I am going to go over and do the same thing for the passenger side light as well. 1:06

Then we are going to start on the driver side of the vehicle, and start plugging our harness in line. On the driver side we are going to be plugging in the port with the yellow and brown wires in them before I actually plug my tail lights back in. We are going to do a couple of other things first, you can see we have a white wire here with a ring terminal on it, that is our ground wire. We need to secure that to the metal on the backside of the tail light assembly. We are going to do that by using the self tapping screw that is provided with the installation kit. Next, we need to take the plugs for the passenger side, along with the 4-pole itself, and feed it down between the opening of the body and the bumper here. 1:44

This space is a little limited though, so to help give us more working room we are going to take off theses two inboard side screws holding the bumper in place. Next, we can start feeding our wires below. With those routed through, I can put these two screws back into place. Then we can plug the other end of the harness back into the tail light. With that done we can put the driver side tail light back on. Now we can move underneath the vehicle and start routing our wires into place. Back up underneath the vehicle, what we have done is take our passenger side connector and our 4-pole wires and routed them up and over the bumper bracket. This is going to help keep it away from the exhaust system. From here I am going to take a 4-pole end and route it to the center of the vehicle. I am going to tie it off at the trailer hitch. Then I am going to take the passenger side connector and route it all the way across. Again, we are going to go up and over the bumper bracket over here as well. 3:17

With it up and over the bumper bracket I am going to take and feed it through the same opening between the bumper and body assembly. Then we will attach it to the passenger side tail light. To aid in the fishing of the wire up to the passenger side tail light, what I have done is route a piece of black gauge wire from the tail light assembly down. I am going to take and tape my harness to it. That is going to allow me to pull it up into place much easier. Then we can just plug our harness in line. From there you want to do a quick double check underneath the vehicle, you want to make sure you do not have any loose or hanging wires that can get pinched or damaged. And your installation will be complete. That will complete the installation of wiring harness part number 118450 on a 2010 Buick Enclave.

This Product Fits The Following Vehicles

2008 - 2012 Buick Enclave All Models

2009 - 2012 Chevrolet Traverse All Models

2008 - 2012 Chevrolet Malibu All Models, except LTZ

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Mounting Bracket 4-Pole Flat $3.19

Pin and Clip For Class III, IV and V Trailer Hitch Receiver $4.99

Ball Mount 3/4" Rise or 2" Drop, 6,000 lbs $17.78

Hitch Ball with 2" Diameter and Medium Shank, 6,000 lbs GTW - Chrome $8.49

4 and 5-Flat Trailer Connector Mounting Box $6.49

Customer Reviews - Write a review about this product

T-One Vehicle Wiring Harness with 4 Pole Trailer Connector - 118450

Average Customer Rating: rating rating rating rating rating 4.8 out of 5 stars (44 Customer Reviews)