T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Rating: rating rating rating rating rating
47 reviews

Code: 118432

Retail:$31.58

Price:$21.95

Shipping Weight: 1 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Trailer Wiring Harness Installation - 2009 Chevrolet Equinox - Video
Trailer Wiring Harness Installation - 2009 Pontiac Torrent - Video
Trailer Wiring Harness Installation - 2007 Pontiac Torrent - Video

Tow Ready Custom Fit Vehicle Wiring - 118432

Tow Ready T-One Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese

Provides a 4-pole flat trailer connector for the vehicle
Quick and Easy
No Cutting, Splicing or Taping
Just Plug in the T-One Connector and You're Ready to Tow
Solid One Piece Construction
16 Gauge Bonded Wire w/ 4-Flat Plug
"Factory" Appearance
Simple Do-It-Yourself Instructions on Every Package

Can be used with 5-pole, 6-pole or 7-pole adapters.

Installation: Connection point is located in the jack storage compartment on the driver's side. Relays and fuses are included to activate the trailer harness. The 4-pole trailer connector will be stowed in the jack storage compartment when not in use.

Please note: Place relays into position with the sloped side of the relays pointing towards the driver side of the vehicle to ensure relays function properly.

Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.

Warning:

Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:

Max. stop/turn light: (7.5 amps)
Max. tail lights: (7.5 amps)

Read vehicle's owners manual and instruction sheet for additional information.

Video of T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Trailer Wiring Harness Installation - 2009 Chevrolet Equinox

Video wiring install 2009 pontiac torrent

Trailer Wiring Harness Installation - 2009 Pontiac Torrent

Video wiring install 2007 Pontiac Torrent

Trailer Wiring Harness Installation - 2007 Pontiac Torrent

Video Transcript for Trailer Wiring Harness Installation - 2009 Chevrolet Equinox

Today on this 2009 Chevrolet Equinox we are going to be installing wiring harness, part number 118432. We are in the rear cargo area of the Equinox and we are going to locate the port that we are going to be pulling the wiring harness into. This is an open ended port, which is located in the floor area of the jack storage compartment. The first thing we need to do is remove the door here and also remove the jack. I will set that off to the side for the time being. :27

It is going to be kind of hard to see, but if I pull the insulation up here, and you take a look inside, you can see the open ended port that is located right there at the bottom area, almost directly below where the jack was stored. What we are going to do is take our open ended wiring harness plug here and plug that directly in. you can see also, that you have an open ended white wire, which is our ground wire. If you look down there again, you can see there is a grounding stud located just to the forward side of where our plug is located. :53

With the port and grounding stud located , we can start installing our harness. To remove the nut off the grounding stud you are going to need a 10 millimeter socket. That is all there is to installing it here at the rear section of the vehicle. You can see the four pole, when not in use can be stored inside the storage compartment. When we want to use it we can just pull it outside the rear cargo door. The weather stripping here at the backside will prevent that from being pinched, so you do not have to worry about that. From there, I am going to remount the jack in the storage compartment, and then we are going to go up under the hood and connect our fuses and relays into place. 1:25

We are up underneath the hood now and we have located our fuse block that we need to plug our fuses and relays into place. This fuse block can be located over on the driver side, just forward of the fire wall here. I am going to go ahead and lift the lid on it. If you look at the backside of the lid, all our fuses and relays are numbered in position. We are going to start by plugging our relays into place. We are looking to plug in our relays at position 58 and 59. These relays are going to activate our right turn and right stop leads and our left turn and left stop leads. When plugging the relays into place, we want the slope side of the relay facing towards the driver side of the vehicle. 2:05

There are three fuses that we need to plug in place as well. These, again are provided with our installation kit and are all 10 amp fuses. For these we need to locate fuse positions number 35, 37, and 43. Position 35 is located right here. Position 37 is located right here. And fuse position 43 is located right here. With the two relays and three fuses in place all of our leads in the tow package should be active now. We want to reinstall the lid to our fuse block and our installation will be complete. This will conclude the installation of wiring harness part number 118432 on a 2009 Chevrolet Equinox.

This Product Fits The Following Vehicles

2007 - 2009 Chevrolet Equinox

2007 - 2009 Pontiac Torrent

2007 - 2009 Suzuki XL7

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Ball Mount 3/4" Rise or 2" Drop, 6,000 lbs $17.78

Pin and Clip For Class III, IV and V Trailer Hitch Receiver $4.99

Hitch Ball with 2" Diameter and Medium Shank, 6,000 lbs GTW - Chrome $8.49

American Flag 2" Trailer Hitch Receiver Cover $14.95

Class II Drawbar 5/8" Rise or 1-1/4" Drop (Kit) $21.95

Customer Reviews - Write a review about this product

T-One Vehicle Wiring Harness with 4 Pole Trailer Connector - 118432

Average Customer Rating: rating rating rating rating rating 4.9 out of 5 stars (47 Customer Reviews)