T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Rating: rating rating rating rating rating
28 reviews

Code: 118424

Retail:$45.16

Price:$34.95

Shipping Weight: 2 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Trailer Wiring Harness Installation- 2010 Acura MDX - Video
Trailer Wiring Harness Installation - 2007 Acura MDX - Video

Draw-Tite Custom Fit Vehicle Wiring - 118424

Tow Ready T-One Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese

Provides a 4-pole flat trailer connector for the vehicle
Quick and Easy
No Cutting, Splicing or Taping
Just Plug in the T-One Connector and You're Ready to Tow
Solid One Piece Construction
16 Gauge Bonded Wire w/ 4-Flat Plug
"Factory" Appearance
Connector is Equipped with a Circuit Protected Taillight Modulite
- Modulite wiring harnesses reduce the strain on the vehicle wiring system by drawing power for the trailer lights directly from the vehicle battery. Circuit protection further safeguards the vehicle from mis-wire situations on the trailer.
Simple Do-It-Yourself Instructions on Every Package

Can be used with 5-pole, 6-pole or 7-pole adapters.

Installation: Connection point is located on the grey electric junction box in the rear of the vehicle, on the driver's side. The 4-pole trailer connector will be stowed in the jack storage compartment when not in use.

Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.

Warning:

Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:

Max. stop/turn light: 1 per side (2.1 amps)
Max. tail lights: (4.2 amps)

Read vehicle's owners manual and instruction sheet for additional information.

Video of T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Trailer Wiring Harness Installation- 2010 Acura MDX

Video install trailer wiring 2007 acura mdx 118424

Trailer Wiring Harness Installation - 2007 Acura MDX

Video Transcript for Trailer Wiring Harness Installation- 2010 Acura MDX

Today on this 2010 Acura MDX we are going to install part number 118424. The first thing we need to do is open up the back tail gate to get to the interior components of the vehicle, because we have to remove a few panels. First off we are going to open up this hatch right here and remove it. Then we will take out the cover for our jack storage compartment. Then we will remove our threshold right here . The reason we are moving all these pieces is because we need access to run our wires from the court, out to where we can use it. :27

This panel pretty much pops up on its own. Now that we have this cover up what is going to happen is we are going to run this T-One connector underneath the plastic inside this panel right here. Lets go ahead and remove this panel, there is our electrical panel right here. This is the T-One connector, this is the port on it. We are going to plug in on the port on the panel right here. We will take our port, run it underneath the panel and up. Just plug it in. Next we will take the ground wire and attach it to this ground stud right here. Put it through our white wire and reattach the bolt to the body along with the other ground wires. 1:10

Now we will go ahead and mount our convertor box, it has a piece of adhesive back here that we are going to use to attach it to this plastic piece right here that will be a good, safe spot for it. At this point here we are going to route this back through our jack storage compartment. We can have it reside in the storage compartment when you are not using it. You can then, pull it out, and shut the door on it. The door seal is thick enough where when you shut the door on it, it will not hurt the wires, all you have to do is make sure you stay away from the center latch and you will be fine. However, in this case we are going to run our wires outside and mount it to the hitch itself. So I have to do a couple more things. We are going to find a location to run the wires out of the body. Right in here there is a grommet, we can pop that out and we can have access through to the outside. As you can see that 4-pull will not fit through there so we are going to take our 4-pull wire and cut it in half and run it through and make new connections on the inside. We are going to cut our wire short right here, just enough so you can still work with it. When you do this you want to make sure there is no power going to this so you do not cross a ground wire with the other circuits just in case something is on. We will go ahead and unplug it from the port. Then lets go ahead and split our wires back. Next we will go ahead and work on our grommet, I am going to take a knife and put a slit through it. You have to make quiet a few passes because it is a pretty thick grommet. From underneath the vehicle we are going to push our wire back through. Then we will slide our grommet back on to our wire and push it back into place and leave it alone for now. 2:56

Now we will reconnect our wires, color for color. Slide on the butt connectors and crimp them into place. Now that we have our connections done lets grab some electrical tape and secure them. Then we will go ahead and reassemble the rest of the vehicle. We will plug back into our port. Now we will get back underneath the vehicle and figure out how to route our wires. I think we will just go along the original harness, above the hanger for the muffler and go over the hitch and then we will come back over the top of the hitch here and then we will mount our bracket on top of the tube here. Keep it a flat alignment with the hitch, mark the holes for it, then drill it out. Alright, we will go ahead and pop our 4-pole into the bracket, it is a friction fit so you have to push it on through, get a good grip on it and kind of pull it out. Then install the hardware that came with the bracket. However, on the other side we are going to add some additional flat washers we found laying around. With everything secured and our wire zip tied in place, that will finish our install of part number 118424 from Tow Ready.

This Product Fits The Following Vehicles

2007 - 2012 Acura MDX

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Ball Mount 3/4" Rise or 2" Drop, 6,000 lbs $17.78

Pin and Clip For Class III, IV and V Trailer Hitch Receiver $4.99

Hitch Ball with 2" Diameter and Medium Shank, 6,000 lbs GTW - Chrome $8.49

Rubber Tube Cover for 2" Trailer Hitch Receivers $8.95

American Flag 2" Trailer Hitch Receiver Cover $14.95

Customer Reviews - Write a review about this product

T-One Vehicle Wiring Harness with 4 Pole Trailer Connector - 118424

Average Customer Rating: rating rating rating rating rating 4.9 out of 5 stars (28 Customer Reviews)