T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Tow Ready Custom Fit Vehicle Wiring - 118353

Tow Ready T-One Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese

• Provides a 4-pole flat trailer connector for the vehicle
• Quick and Easy
• No Cutting, Splicing or Taping
• Just Plug in the T-One Connector and You're Ready to Tow
• Solid One Piece Construction
• 16 Gauge Bonded Wire w/ 4-Flat Plug
• "Factory" Appearance
• Simple Do-It-Yourself Instructions on Every Package

Can be used with 5-pole, 6-pole or 7-pole adapters.

Installation: Connection points are located behind the vehicle taillights. The 4-pole trailer connector will be stowed under the vehicle close to the trailer hitch. A mounting bracket is recommended.

Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.

Warning:

Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (4 amps)

Read vehicle's owners manual and instruction sheet for additional information.

This Product Fits The Following Vehicles

1987 - 1997 Nissan Pickup

1987 - 1995 Nissan Pathfinder 2 and 4 Dr.

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Ask the Experts about this Tow Ready Custom Fit Vehicle Wiring
Do you have a question about this Custom Fit Vehicle Wiring?

• Left Turn Signal Causes all Trailer Lights to Flash and Right Turn Signal Does Nothing
  
• If you have the Tow Ready Wiring Harness # 118353 installed on your 1997 Nissan Pickup you will want to check the 4-flat connector with a circuit tester like the Quickee Tester # 3808 and make sure that the wiring on the vehicle is correct and that you have a good ground. It sounds like a ground problem on the trailer is what is causing your lighting problem. You will want to check that the white ground wire on the trailers 4-way is properly grounded to a good, clean area of bare metal on the
  view full answer...


• Troubleshooting Trailer Light Turn Signal Functions Reversed on Trailer
  
• If you used a wishbone type of wiring on the trailer, it could be lending to the issue you are having. With a wishbone wiring harness on the trailer, the running light signal is split at the plug and carried down two separate wires; one for the left (yellow with brown) and one to the right (green with brown). If it was these wires that got switch and not the turn and brake wires, you will still have the blinker problem. What you will need to do is use a circuit tester like the Quickee # 3808,
  view full answer...


• Diagnosing Trailer Wiring Problem on 1995 Nissan Pickup
  
• A ground problem is a possibility, but having an insufficient ground connection usually causes the trailer lamps to behave erratically, or to work properly until the vehicle headlights are switched on. The best place to start would be to use a circuit tester like part # 3808 and test the trailer connector as each function is tested. This will tell you if the problem exists on the vehicle or the trailer. If your testing shows that the trailer connector is functioning properly, then you kno
  view full answer...


• Parts Needed to Wire Lighting Functions When Flat Towing a 1997 Nissan Pickup Truck
  
• The T-One Vehicle Wiring Harness, # 118353, is for the Nissan if it were towing a trailer and needed to power the trailer lights. Instead, there are a couple of different options for when you are towing the Nissan and need lights. Since you mentioned that you wanted to power the Nissan lights, you will want to use a diode kit, # RM-154. Installing this kit will put the turn signals and brake lights on the same bulb and the running lights will be on a separate bulb. If you want the turn signal
  view full answer...


• Availability of a Trailer Wiring Harness To Fit A 1986 Nissan D21 Hardbody Truck
  
• If you have the mid-year 1986.5 Nissan Hardbody that has the two large headlights rather than the four smaller lights on the older model, you can use the Tow Ready T-One Wiring Harness, part # 118353, to install a 4-Way at the rear of your vehicle. The # 118353 wiring harness will plug into the back of your vehicles taillights. I am including a link to the installation instructions on the # 118353 wiring harness. If your vehicle is not the 1986.5 or newer model, you will need to hardwire t
  view full answer...