T-One Vehicle Wiring Harness with 4 Pole Trailer Connector

Tow Ready Custom Fit Vehicle Wiring - 118308

Tow Ready T-One Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese

• Provides a 4-pole flat trailer connector for the vehicle
• Quick and Easy
• No Cutting, Splicing or Taping
• Just Plug in the T-One Connector and You're Ready to Tow
• Solid One Piece Construction
• 16 Gauge Bonded Wire w/ 4-Flat Plug
• "Factory" Appearance
• Simple Do-It-Yourself Instructions on Every Package

Can be used with 5-pole, 6-pole or 7-pole adapters.

Installation: Connection points are located behind interior trim panels close to the taillights. The 4-pole trailer connector will be stowed inside the trunk when not in use.

Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.

Warning:

Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:

• Max. stop/turn light: 1 per side (2.1 amps)
• Max. tail lights: (4 amps)

Read vehicle's owners manual and instruction sheet for additional information.

Replaces # 18308

Close-up picture of the connectors.

This Product Fits The Following Vehicles

2002 - 2006 Toyota Camry

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Ask the Experts about this Tow Ready Custom Fit Vehicle Wiring
Do you have a question about this Custom Fit Vehicle Wiring?

• T-One Wiring Harness for a 2003 Toyota Camry
  
• We offer a T-One Wiring Harness, part # 118308, that will simply plug into your vehicle and provide you with a 4-pole Flat trailer connector. The harness is simple to install, it plugs inline into the factory connectors located behind the tail light assemblies with no cutting, taping, or splicing required.
  view full answer...


• T-One for 2005 Toyota Camry 118308 circuit protection
  
• No, the black box on the 118308 wiring harness is a converter that converts the vehicles 4 circuit wiring to work with the trailers 3 circuit wiring, and it does not protect the vehicle from any damage that could be caused if there is a problem with the trailer wiring. We do not have a separate circuit protector available, but we have a circuit protected converter, part # 119175, that you could hard wire into your vehicles taillights. You may also need a circuit tester, part # 3808, to install
  view full answer...


• How Does the Tow Ready Wiring Harness # 118428 Connect to a 2002 Toyota Camry Turn/Brake Circuit
  
• To install this T-One Vehicle Wiring Harness, part # 118308, you will first locate the vehicle wiring in the trunk by removing separate the vehicle wiring connectors on the driver side and install the harness that contains the yellow wires. On the passenger side you will repeat the same process as above with the green wire connector. These connectors should fit in line with the tail lights that are on your 2002 Toyota Camry. You should be able to just undue the connectors and put the two c
  view full answer...


• How Does the 4-Way of the Tow-Ready Harness # 118308 Route to the Outside of My 2002 Toyota Camry
  
• When you need to use the 4-way from the Tow Ready Custom Fit Vehicle Wiring, part # 118308, you will simply open the trunk, pull the 4-way out and then close the trunk over the connector. The rubber weather seal will prevent any damage from occurring to the wire as it gets shut. I would try to keep the wire clear of the trunk latch and you should be fine. I attached installation instructions below for you to check out also.
  view full answer...


• Trailer Lights Not Working When the Headlights are Turned On in a 2003 Toyota Camry
  
• It sounds like you have a ground issue. When the headlights are on, the highest amperage draw is placed on the wiring system and, a faulty ground will show at this time. Make sure you have good metal to metal contact. Paint and corrosion can act as insulators, so make sure the grounds are touching clean metal. I would check all of the ground connections on the trailer. First, check the ground at the trailer tongue. Take the ground loose and clean the connection point on the trailer and the w
  view full answer...