T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

Rating: rating rating rating rating rating
28 reviews

Code: 118302

Retail:$45.16

Price:$32.95

Shipping Weight: 2 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Trailer Wiring Harness Installation - 2006 Honda Accord - Video

Tow Ready Custom Fit Vehicle Wiring - 118302

Tow Ready T-One Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese

Provides a 4-pole flat trailer connector for the vehicle
Quick and Easy
No Cutting, Splicing or Taping
Just Plug in the T-One Connector and You're Ready to Tow
Solid One Piece Construction
16 Gauge Bonded Wire w/ 4-Flat Plug
"Factory" Appearance
Simple Do-It-Yourself Instructions on Every Package

Can be used with 5-pole, 6-pole or 7-pole adapters.
Installation: Connection points are located behind trunk liner on the driver's side. Wiring harness will remain in trunk for storage.
Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.

Warning:

Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:

Max. stop/turn light: 1 per side (2.1 amps)
Max. tail lights: (4.2 amps)

Read vehicle's owners manual and instruction sheet for additional information.

Replaces # 18302

Video of T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Trailer Wiring Harness Installation - 2006 Honda Accord

Video Transcript for Trailer Wiring Harness Installation - 2006 Honda Accord

Today we are going to be installing wiring harness part number 118302 on a 2006 Honda Accord. We are inside the trunk area here. The connection points are actually located behind the tail light assembly, so we are going to need to remove this rear threshold piece. There are push rivets located here that are holding the threshold piece on. I am going to take a flat-bladed screwdriver and just gently pull up. OK, next I am going to go ahead and remove the carpeting. To do so, there are two Phillips-head screws that we are going to take out. We are going to remove the plastic plugs that are in here as well, and that will allow us to pull the carpeting back here. So here on the drivers side we are going to go ahead and make all three of our connections.

We are going to start with the connector with the yellow wire, and that one is going to actually plug into the top plug-in here on the drivers side, and then back into the tail light. The second connector, with the brown and red wires, that is going to plug into the lower connector on the back of the tail light. And lastly we are going to take the connector with the green wire, single-sided here. See, there is a little connector here taped to the main wiring harness right in between the two connections that we just made. Here, below where our connections were made, you can see there is a grounding stud. We are going to take that, remove the bolt there, and add our ground wire to that connection point. We want to mount our converter box here.

As you can see here on the back side, we have got a piece of double-sided tape. I am just going to go ahead and probably mount that directly, down here next to where the main wiring harness is. The connector is going to stay inside the trunk here when not in use. And when we go to use it, we are just going to pull it out of the trunk here. The weatherstripping here along with the threshold will prevent the harness from pinching at all. From there, we just need to put the interior of the vehicle back together and then our installation will be complete. You may want to secure any loose wires that you may have here with a zip-tie that is provided in the installation kit. This will conclude the installation of wiring harness part number 118302 on a 2006 Honda Accord.

This Product Fits The Following Vehicles

2006 - 2010 Acura TSX

2003 - 2007 Honda Accord 4 Dr. Sedan

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Hitch Ball with 1-7/8" Diameter and Short Shank, 2000 lbs GTW - Chrome $7.49

Rubber Tube Cover 1-1/4" $4.29

Sportframe Drawbar 2-1/8" Rise or 2-3/4" Drop 2000# Kit $21.95

Hitch Ball with 2" Diameter and Short Shank, 3,500 lbs GTW - Chrome $7.49

Hitch Ball Cover for 1-7/8" and 2" Diameter Hitch Balls $2.56

Customer Reviews - Write a review about this product

T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118302

Average Customer Rating: rating rating rating rating rating 4.9 out of 5 stars (28 Customer Reviews)