Draw-Tite T-One Vehicle Wiring Harness

Rating: rating rating rating rating rating
45 reviews

Code: 118300

Retail:$31.58

Price:$27.95

Shipping Weight: 2 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Trailer Wiring Harness Installation - 2007 Chrysler Town and Country - Video
Trailer Wiring Harness Installation - 2004 Chrysler Town and Country - Video
Trailer Wiring Harness Installation - 2005 Dodge Caravan - Video
Trailer Wiring Harness Installation - 2004 Dodge Grand Caravan - Video
Show all 6 videos

Tow Ready Custom Fit Vehicle Wiring - 118300

Tow Ready T-One Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese

Provides a 4-pole flat trailer connector for the vehicle
Quick and Easy
No Cutting, Splicing or Taping
Just Plug in the T-One Connector and You're Ready to Tow
Solid One Piece Construction
16 Gauge Bonded Wire w/ 4-Flat Plug
"Factory" Appearance
Connector is Equipped with a Circuit Protected Taillight Converter

Protects itself and the tow vehicle against harmful electrical shorts and mis-wire situations.

Simple Do-It-Yourself Instructions on Every Package

Can be used with 5-pole, 6-pole or 7-pole adapters.

Installation: Connection points are located behind the vehicle taillights. 4-Pole flat trailer connector will be stowed inside the jack storage compartment in the rear cargo area when not in use.

Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.

Warning:

Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:

Max. stop/turn light: 1 per side (7.5 amps)
Max. tail lights: (7.5 amps)

Read vehicle's owners manual and instruction sheet for additional information.

Picture of the driver side connectors.

Replaces # 18300

Video of Draw-Tite T-One Vehicle Wiring Harness

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video wiring install 2007 chrysler town and country

Trailer Wiring Harness Installation - 2007 Chrysler Town and Country

Video wiring install 2004 chrysler town and country

Trailer Wiring Harness Installation - 2004 Chrysler Town and Country

Video install trailer wiring 2005 dodge caravan 118300

Trailer Wiring Harness Installation - 2005 Dodge Caravan

Trailer Wiring Harness Installation - 2004 Dodge Grand Caravan

Trailer Wiring Harness Installation - 2005 Dodge Grand Caravan

Video install trailer wiring 2005 dodge grand caravan 118300

Trailer Wiring Harness Installation - 2005 Dodge Grand Caravan

Video Transcript for Trailer Wiring Harness Installation - 2007 Chrysler Town and Country

Today on this 2007 Chrysler Town and Country we are going to install part number 118300 from Tow Ready. First open up the back hatch of the vehicle and disconnect the tail lights. To take off the tail lights what we need to do is pull out these two plastic rivets right here. Swing it out and it pops right out. To disconnect the wire harness we have to push in this red tab right here so it unlocks. Push down at the top of the wire harness and it should come right apart. Repeat the same process on the passenger side. Next we are going to pull out this grommet right here and we are going to make a slit in it so we can run our new harness back through here. We are going to leave it like that for now. Repeat the same thing on the other side. 00:47

Next open up the jack storage compartment. Take out the jack tools for now. What is going to happen is from the outside we are going to pull the 4-pole wiring harness back into the jack storage compartment. That is where it will stay when it is not being used. We are going to take the 4-pole of the T-One connector and push it to the inside. There is some insulation inside here that you may have to move around to get to it. Generally if you push most of the wiring harness in there you can get a hold of it somehow if you pull the rest through. We are going to pull all of this through until we get to the T-One connector with the yellow wire and we will stop before we pull it inside the vehicle. However, we still need to pull our T-One connector with the white and green wire all the way through and then we are going to run it across to the other side. We are going to leave all of that alone for now and we are going to go back to the tail light. 01:35

This is our factory wire harness from the vehicle and we are going to add on our T-One connector, it will snap into place, push the red lock pin in, and take this half and put it inside the vehicle. Then we are going to put our grommet along the white wires and put everything back. At this point we can reinstall the driver side tail light. Now we have got our T-One connector with the green and white wire and we are going to run it underneath the plastic all the way across. I am going to take this carpet loose too because we are going to sneak the wire underneath the carpet. We are going to sneak it underneath the plastic here and we will work our way across. Pull this panel apart on the passenger side and run our wires in. Right here behind this blower assembly there is more insulation right here and we will put a fish wire from the outside in and pull it through and use that wire to pull our T-One connector back out. The same thing is going to apply as on the driver side. We will connect the wire harness from the vehicle to our T-One connector and put everything to the inside. Make sure you leave the ground screw hanging out and we will reinstall the grommet. All we have to do for our ground screw is attach it straight to the sheet metal right here. Then put the tail light back together. Reinstall the interior panels. Tuck away any loose wires you have. Right now I am going to take the wire and wrap some electrical tape around it to help keep it contained a little bit. We will reinstall the jack tools now. Take the wiring harness and store it inside there when it is not being used. To use the harness just get into your jack storage compartment and pull it out, however much you need. You can then shut the door on it, just be sure you stay away from the center latch and it should be fine. If you need to you can still pull out extra. That finishes our install of part number 118300 from Tow Ready.

Right here behind this blower assembly there is more instillation in here, what we will do is go ahead and put a fish wire from the outside, in, and pull it through and we will use the wire to pull out T-Connector back out. Same thing is going to apply like on the drivers side. We will connect our wire harness from the vehicle to our T-Connector and put everything inside. Just make sure we leave our ground screw hanging out, and we will go ahead and reinstall the grommet. We will attach our ground wire straight to the sheet metal here. Then put the tail light back together. Next, reinstall the interior panels here and tuck away any loose wires that are hanging out. Now, we are going to take the wire and wrap some electrical tape around it to help keep it contained a little bit. We will reinstall the jack tools now and take our wire harness and store it inside here when it is not being used. 3:47

To use the harness, again open your jack storage compartment and pull it out. Pull out what you need and then shut the door on it, just be sure you stay away from the center latch here and you should be fine. If you need to you can pull out extra still. That finishes our install of part number 118300 from Tow Ready.

This Product Fits The Following Vehicles

2004 - 2004 Dodge Caravan All Models including 4WD

2004 - 2004 Dodge Grand Caravan All Models including 4WD

2004 - 2004 Chrysler Town and Country All Models including 4WD

2005 - 2007 Dodge Caravan with Stow-N-Go Seats

2005 - 2007 Dodge Grand Caravan with Stow-N-Go Seats

2005 - 2007 Chrysler Town and Country with Stow-N-Go seats

2005 - 2007 Dodge Caravan without Stow-N-Go seats

2005 - 2007 Dodge Grand Caravan without Stow-N-Go seats

2005 - 2007 Chrysler Town and Country without Stow-N-Go seats

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Pin and Clip For Class III, IV and V Trailer Hitch Receiver $4.99

Ball Mount 2-3/4" Rise or 4" Drop, 6,000 lbs $20.63

Hitch Ball with 2" Diameter and Medium Shank, 6,000 lbs GTW - Chrome $8.49

Hitch Ball with 2" Diameter and Short Shank, 3,500 lbs GTW - Chrome $7.49

Class II Drawbar 2-5/8" Rise or 3-1/4" Drop (Kit) $21.95

Customer Reviews - Write a review about this product

Draw-Tite T-One Vehicle Wiring Harness - 118300

Average Customer Rating: rating rating rating rating rating 4.9 out of 5 stars (45 Customer Reviews)