Curt Trailer Hitch Receiver with Drawbar - Custom Fit - Class I - 1-1/4"

Curt Trailer Hitch - 11469

Perfect for light-duty towing, this custom, vehicle trailer hitch receiver features fully welded, gloss powder coated steel construction. Drawbar, pin and clip are included.

Features:

• Custom fit is designed specifically for your vehicle
• Precision, robotic welding maximizes strength and improves fit
• WeatherTite construction prevents interior rust by sealing main body
• Bolt-on installation - no welding required
  • Complete hardware kit and installation instructions included
• Lifetime technical support from the experts at etrailer.com
• Gloss black powder coat finish over steel resists corrosion
• Stylish, round-tube design
• Drawbar, pin and clip included
• Made in USA

Specs:

• Receiver opening: 1-1/4" x 1-1/4"
• Rating: Class I
  • Maximum gross trailer weight: 2,000 lbs
  • Maximum tongue weight: 200 lbs
• Limited lifetime warranty

Note: All non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps. Failure to properly support these loads will void your hitch warranty from Curt.

etrailer.com Technical Support

At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.

11469 Curt Class 1 Trailer Hitch Receiver

Video of Curt Trailer Hitch Receiver with Drawbar - Custom Fit - Class I - 1-1/4"

This Product Fits The Following Vehicles

2010 - 2011 Toyota Prius

Customers Who Purchased This Trailer Hitch Also Bought...

Ask the Experts about this Curt Trailer Hitch
Do you have a question about this Trailer Hitch?

• Trailer Hitch Ball Shank Size and Use of Hitch Adaptrers on a 2010 Toyota Prius
  
• Class 1 receiver hitches use a 3/4 inch ball shank size. I would recommend item # 19256, for a 1-7/8 inch ball for your hitch or the item # 19258, 2 inch ball. 1-1/4 inch to 2 inch Trailer Hitch adapters like the Hitch Adapter 1-1/4 inch to 2 inch Trailer Hitch Receiver, item # HTAD, are not to be used for towing because the use of an adapter significantly reduces the tongue capacity of the trailer hitch and puts excess stress on the hitch if used for towing due to the extended length from th
  view full answer...


• Is the Required Curt Stabilizing Strap Included with Hitch # 11469 for a 2010 Toyota Prius
  
• The Curt Stabilizing Strap, part # 18050, is not included with their hitches. It attaches to the bike rack then to the vehicle to keep the forces exerted on the bike rack and hitch when hitting bumps from damaging the hitch. On passenger cars this can be attached to the edge of the trunk lid that meets rear windshield or on SUVs, you can attach to the top edge of the hatch. The use of a strap is necessary for Curt warranty requirements. You can also use bungee cords like # 3044DAT, or a ratc
  view full answer...


• Will the Thule Helium Trailer Hitch Mount Bike Rack Fit a 2010 Toyota Prius with a Curt Hitch
  
• The Class I trailer hitches have a stop built into them that prevent the accidental use of a Class II accessory. The older versions of the Helium had a longer shank and thus could not fit in a Class I hitch. The new versions will. A Curt trailer hitch, # 11469, should allow the old version to fit. However, the 971 Helium is a 3 bike carrier but on a Class I trailer hitch, you will be limited to carrying just 2 bikes. The reason is that a Class I trailer hitch cannot handle the stress of a thi
  view full answer...