Select Your Vehicle

View Cart


2013 Dodge Durango Roof Rack by Yakima

Roof Rack Includes:

Round 58" CrossBars for Yakima Roof Rack System (QTY 2)
Q10 Q Clips for Yakima Q Towers (QTY 2)
Q99 Q Clips for Yakima Q Towers (QTY 2)
Yakima Q Towers Roof Rack Feet for Naked Roof (QTY 4)


Yakima

Part Numbers: Y00409,Y00610,Y00699,Y00124

Price:$370.40

$296.40 after
Up to 20 Percent Off Select Yakima Products

Shipping Special





Round 58" CrossBars for Yakima Roof Rack System (QTY 2)
part number: Y00409

These multipurpose, galvanized steel crossbars supply the backbone for your aftermarket roof-rack system. Bars provide stability to your rack system and carry the accessories that secure your gear. Round design fits all Yakima towers.

Features:

  • Serve as backbone of your aftermarket roof-rack system
  • Provide stability to roof-mounted racks
  • Carry the accessories that secure your gear (bike racks, kayak carriers, etc.)
  • Fit all Yakima towers
  • Constructed from vinyl-coated, galvanized steel


Specs:

  • Quantity: 2
  • Capacity (depending on application):
    • 5 Bikes
    • Yakima SkyBox Pro 12, PowderHound and 1 bike
    • 2 Kayaks
    • 2 Bikes and Yakima BasketCase
    • 2 Kayaks on Yakima Kayak Stacker and 2 bikes
    • Yakima SkyBox Pro and 2 bikes
    • Yakima SkyBox Pro and kayak on HullRaiser
  • Dimensions: 1-1/8" diameter x 58" long
  • Steel wall: .085" thick
  • Lifetime warranty

NOTE: Load bars do not include end caps. The end caps are included with Yakima roof rack or ladder rack towers. Load bar end caps are also sold separately (part number Y8007026).



8000409 Round 58" CrossBars for Yakima Roof Rack System (QTY 2)



Q10 Q Clips for Yakima Q Towers (QTY 2)
part number: Y00610

Q Clips integrate with Yakima Q Towers to provide a secure base for your aftermarket roof-rack system. Clips are vehicle specific; they are required for mounting Q Towers to your doorframe.

Features:

  • Work with Yakima Q Towers to form base for aftermarket roof-rack system
    • Required for mounting Q Towers to vehicle doorframe
  • Designed as vehicle-specific application
  • Provide base pads for bottom of Q Towers
    • Pads keep towers from damaging vehicle paint job
  • Constructed of thin, strong, stainless steel
    • Resists rust
    • Will not interfere with door closure


Specs:

  • Quantity: 2
  • 2 Kits required for most vehicles
    • Vehicles often require two different sets of clips for installation of Q Towers
  • Lifetime warranty


8000610 Q10 Clips for Yakima Q Towers



Q99 Q Clips for Yakima Q Towers (QTY 2)
part number: Y00699

Q Clips integrate with Yakima Q Towers to provide a secure base for your aftermarket roof-rack system. Clips are vehicle specific; they are required for mounting Q Towers to your doorframe.

Features:

  • Work with Yakima Q Towers to form base for aftermarket roof-rack system
    • Required for mounting Q Towers to vehicle doorframe
  • Designed as vehicle-specific application
  • Provide base pads for bottom of Q Towers
    • Pads keep towers from damaging vehicle paint job
  • Constructed of thin, strong, stainless steel
    • Resists rust
    • Will not interfere with door closure


Specs:

  • Quantity: 2
  • 2 Kits required for most vehicles
    • Vehicles often require two different sets of clips for installation of Q Towers
  • Lifetime warranty


8000699 Q99 Clips for Yakima Q Towers



Yakima Q Towers Roof Rack Feet for Naked Roof (QTY 4)
part number: Y00124

For vehicles with a naked roof, Q Towers provide the base for building your own from-scratch system. Towers hold crossbars securely in place and ensure a perfect fit, with clips (sold separately) that are vehicle specific.

Features:

  • Provide base for rack system on vehicles without rain gutters or factory racks
  • Ensure perfect fit with tower and clip that move in 4 different ways (Quadruple Movement)
    • Attach using interchangeable, vehicle-specific Q Clips (sold separately)
  • Adjust to contours of vehicle with ball-and-socket mechanism
  • Have die-cast interior to form solid, sturdy anchor to support load
  • Are lockable with Same Key System (SKS) Cores (sold separately)
    • Cores lock crossbars to towers and towers to vehicle roof
    • SKS Cores can be changed out to make all your Yakima locks keyed alike
  • Remove and install quickly and easily following initial setup


Specs:

  • Quantity: 4
  • Additional components required for complete roof-rack system
    • Q-Clips (sold separately) for vehicle-specific mounting
    • Crossbars (sold separately) to provide attachment point for accessories
  • SKS Cores required: 4
  • Height: 5-1/4" from base to top of bar
  • Lifetime warranty


8000124 Yakima Q Towers for Roof Rack Base (QTY 4)



Video of Round 58" CrossBars for Yakima Roof Rack System (QTY 2)


Videos are provided As a guide only. Refer To manufacturer
installation instructions And specs For complete information.




Video Transcript for Yakima Roof Rack Review - 2016 Acura MDX

Today on our 2016 Acura MDX, we're going to be doing a test fit of the Yakima roof rack system. It's going to be part number Y00409, Y00124, and finally part number Y00731. As you can see, we've already got the first one up on the vehicle. That's going to be spaced off that front windshield 6" with an inside measurement from each Q Tower of 48". We'll explain how the second one goes together and the final measurements you need to make. The bar here is going to be your part number Y00409. You're going to have your Q Towers, which are going to be part number Y00124; and then finally, your fit kit for the vehicle specific, which is going to be part number Y00731. As you can see, we've already got one side on.

We'll show you how to put this side on over here. First thing you're going to want to do is get it set up on a flat surface. That way when you set your other Q Tower on, it will sit flat. That way when you get it up on the vehicle, you don't have one side looking like this. Go ahead and slide that Q Tower over the end just like so.

Then this inside measurement on the back bar needs to be 47-1/4". We'll get the even amount of space. We'll take our roll tape and just roll it out to 47-1/4". It looks like it's going to be right about there. Our bar overhang ...

Get a level here; 47-1/4". Then we will take our Allen tool, making sure this is out so that sits flat on the ground, space out the back part here, and you'll see that there's going to be a screw in here on the inside when you pull this cover back. We're just going to tighten that down. That will secure this Q Tower in place. Now we'll just make sure that our measurements stay the same and that there was no deviation. Looks like we had a little bit here, so let me adjust this one.

That way we can have that right measurement on the inside with the equal amount of bar overhang. We'll just loosen this side up and just slide it back just a little bit, tighten it back down, and we'll check this side. This takes just a second do. You want to make sure you get it right the first time. That way when you get it up on the vehicle, you don't have any further troubles. We'll check it all up here real quick: 47-1/4" as you can see there and 3-1/8" overhang on each side. Place our covers on the ends. Those pieces are secured now, the Q Towers are. Now we're going to place on the Q Clips. This is going to be your fit kit here. You're taking and place your . We'll rotate it around here so you can see the bottom. You can see how that's shaped and how this is shaped, those little squares will fit down in there. We'll just press this into place. This will be that protective rubber barrier between your paint and the top of your vehicle and your roof rack system. Once you have that on, we'll then take our clip . This is going to go underneath the door frame on the inside like you see up there. First you'll need to remove the safety clip and then the lock set. This lock set, it will come with the plastic inserts, but you can also get the metal inserts as well. You slide that down in just like so to where the sides of this will stick through the slots on either side and the holes will line up on the front. Place your lock set back in just like so. Then place the clip back over the top. That will secure that clip in place. From there, we'll take our regular standard screwdriver and open up the back doors. That way we can prep it for putting our rack up on top. All right, now we will place it over the top making sure that our feet sit down nicely. You can see will need to loosen that up just a little bit. We'll take our flat-head screwdriver or standard screwdriver and loosen that screw on the top until that plate drops right underneath. Then we'll move over to the other side and check it. Just like so. All right, you can see that this side was sitting down further, so we can tighten up this side and bring that screw back up in just like so, working back and forth until we get it right where it needs to be. You want to make sure that this is as even as possible. Now the next measurement we're going to get is going to be our crossbar spread. That's going to be 32" from center-to-center of your crossbars. That way we can ensure we get it in the right location. You can see we're pretty close there. We're about 3/4" off. We'll just bring this back one forward a little bit until it meets up 32" in the center. I'll just check the other side and get it equal. If it helps, you can use a normal tape measure as well. All right, once we have them even, we'll then close down the side just like so. You'll see a slight bow in the bar. That will ensure that you have it tight and secure. Now that you've seen the Yakima roof rack system for the 2016 Acura MDX, part number Y00409, Y00124, and part number Y00731, that will complete our test fit for today. .



Customer Reviews

Round 58" CrossBars for Yakima Roof Rack System (QTY 2) - Y00409

Average Customer Rating:  4.8 out of 5 stars   (49 Customer Reviews)

These multipurpose, galvanized steel crossbars supply the backbone for your aftermarket roof-rack system. Bars provide stability to your rack system and carry the accessories that secure your gear. Round design fits all Yakima towers.


- Y00409

by: Pat G08/29/2013


Great first experience dealing with you guys! Shipped fast, and was a faster install. You gave me the right parts and it went together in a flash. Will definitely be doing business with you all again. 97525



- Y00409

by: John K08/17/2012


Free delivery that showed up in 3 days!!! Can't beat it. The crossbars with the Control Towers and LandingPad 9 fit perfectly on my Honda Element. Had them installed in about 30 mins. Don't have my cargo box yet and wanted to test strength, so I had my 110lb wife standing on them with no issues (yes, the car was parked). Plan to take a long camping trip next week with a cargo box on top...wife will be in the vehicle:-) 52048


Comments

Do you have a video to see how it looks while you install that rail track roof device.

comment by: Teodoro G - 08/25/2013


1959

We have quite a few videos of Yakima roof rack installations. Is there a vehicle in particular you are looking for?

Patrick B - 8/26/2013




- Y00409

by: Joe C12/30/2012


The only reason I am not giving it an excellent rating is the considerable wind noise that occurs. While we had our luggage carrier atop our car it seemingly imperceptible, however after driving around for a week while on vacation with simply the bars breaking the wind it was quite loud. With that being said they were a breeze to install, aside from having to use allen tool tighten down the fittings. I later discovered that a wratcheting screwdriver with the correct bit size provided for much faster installation and removal. I would definitely recommend for purchase. 62262



- Y00409

by: Paul D.08/19/2012


A great company to do business with, and lots of merchandise in stock. I orderd a roof rack for my truck on Tuesday morning and it was on the porch when I returned from work on Thursday. I will deffinitely order more from etrailer.com 52267



- Y00409

by: GGYule02/13/2012


I ordered the Yakima Roof System for my Honda Element. I had amazingly fast delivery. Product exactly as advertised and the cost was lower than most other dealers. etrailer went the extra mile to get me my order as fast as possible (I didn't ask for quick delivery they just went ahead and took the initiative) and kept me well informed about its progress. I'd do business with them again in a heartbeat. 31755



- Y00409

by: Sean M.06/30/2012


Etrailer is great with price and service. They upgraded my shipping for free and they are excellent with follow up emails to make sure I'm satisfied. As for the product, I am surprised with the amount of wind noise with the round Yakima bars. I previously had Barrecrafters on my Land Cruiser and didn't notice noise with them. If I knew before I would have upgraded to one of the Aero bars. 46339



- Y00409

by: Dick D.07/20/2012


everything was great, got a day earlier than expected, fit fine, not to hard to install, I would recommend a helper the first time you are trying to get all the adjustments correct, 3 hands are needed at times. I worry a little about the rubber rain seal not working properly, has not been rained on yet. Using it to haul a kayak. Great price compared to local truck accessory store. 48689



- Y00409

by: Rick U.07/24/2012


Thank you for the quick shipment of my new Yakima Q tower roof rack for my 2007 F150 King Ranch. Following the simple instructions it went together easily and works and looks great. The follow up after purchase has been great from etrailer and I felt like if there had been a problem they would have been there to help me through it. Thank you! 49155



- Y00409

by: Lang Family05/26/2012


We ordered the Yakima RailGrab Towers and Cross Bar set for our Taurus X to hold 2 kayaks and it was perfect! The instructions were clear, even added some humor which was welcome. They were shipped with the exact timeframe promised which was good as we needed them before our Memorial Day camping trip. Thank you. We will recommend to others. 41749



- Y00409

by: Richard J11/22/2011


Roof rack kit worked perfectly. I tried to find out what kit I needed from the Yakima website but their fit my car function would not load. I was relieved to see that etrailer had their own kit to fit my car. I didn't have to worry that I ordered incompatible parts. Installation took less than an hour and the rack works great. 27285



- Y00409

by: Jeremy05/01/2012


Just follow the directions and everything will workout. Took me 35 to 40 minutes but I thought I knew what I was doing without directions. Follow the measurements for our vehicle and it works perfect, just remember to order the air deflector to eliminate the wind noise. Always great service and delivery was very fast. 39091



- Y00409

by: Kyle Z07/31/2013


I have included a picture of my 2008 Mitsubishi Eclipse, with the Yakima Q System and Even-Keel Kayak saddles. I also used a stretch Kit, which I picked up locally due to time constraints. I'll be sure to keep you guys in mind when I am ready to get additional parts for the system. 92525



- Y00409

by: Peggy S.12/27/2010


Roof rack for Ford Explorer Bought the rack for my son for Christmas. Ordered it on Tuesday and received the correct item on Friday. He out it on his rig on Saturday! So many times I order items that do not fit. This was nice dealing with you for the first time. Thank you, Peggy 4680



- Y00409

by: Michael J.07/22/2011


Clear concise instructions, easy to follow. Installed onto my 2004 Honda Pilot. No hiccups; the hardest part was reading my old tape measure in order to get things fasten down symmetrically. I highly recommend this product. Thank you Yakima and thank you etrailer. 19994



- Y00409

by: Ronnie07/09/2012


2009 silverado Yakima roof rack 47294



- Y00409

by: Jason11/16/2012


etrailer shipped my order very quickly and the product arrived in condition. The system was relatively easy to install. You must take your time and measure multiple times for correct placement and tightening. 59491



- Y00409

by: Scott08/08/2012


I ordered the Yakima base rack system for my 2011 Mazda CX-7, and it arrived in a timely manner and the product fit perfect and is top notch quality as always with Yakima. Thanks Yakima and etrailer.com 50966



- Y00409

by: Greg05/18/2011


Was very pleased with the Yakima racks and installation was a snap! First time customer of etrailer and was elated with whole experience! Shipping was lighting fast too!!! Will do business again... 14727



- Y00409

by: Micheal N.12/02/2011


Nice strong bars. These bars are great and worth the price. I put them on my 2004 Tahoe and they look good. Very easy to install. I would recommend to anyone looking for heavy duty crossbars. 27615



- Y00409

by: Erin McAleer03/12/2012


The product came fast and as promised. The roof rack went together fairly smoothly. You can definitely hear the wind resistance from the rack, and the bars are a lot heavier than I expected. 33590



- Y00409

by: Kevin J.10/27/2011


The roof rack worked wounderfully.. Assembly was sopt on with the instructions. Delevery was promp and as estimated in the tracking program .. Great shopping with you guys.. Kevin J..NY 26226



- Y00409

by: kerwin t. keiffer04/04/2012


all put together and installed. had to adjust measurements a little to fit my cargo carrier. if it doesn't fly off on our way back to washington i'll be happy. thanks---lotgg 36151



- Y00409

by: JC05/21/2012


Received the product with everything intact. Instructions were easy to understand and took little time to assemble. Soild product, I'll let you know how solid after my trip:) 41094



- Y00409

by: Pete07/09/2011


Rails installed easily and without an issue! Shipping was supposed to take 3-7 days but arrived in <2 days. For after market cargo add-ons, I won't go anywhere else! 19014



- Y00409

by: Stacie Temple01/03/2011


Great Experience I know nothing about this sort of thing and your company made it so easy to find what I needed, order it, and have it delivered. Thanks. 4916



- Y00409

by: Tony B.12/09/2012


When I bought the rack, I didn't realize that it was easily removable. This is exactly what I need to carry my Pirogue around on my Element. 61001



- Y00409

by: Brig Harris05/15/2012


It looks great and was alreadt set up to fit my wife's Honda Pilot... Thanks and I will follow up when I order my rack for my 2012 Civic 40556



- Y00409

by: Cindy lou09/22/2012


so simple to enstall, I orderd the locks and the fairing after I put the racks on.. will share picture after the new order comes in 55489



- Y00409

by: Frank P.01/07/2013


Very nice equipment for a great price. Fast shipping. was able to track my order the whole way to Maryland. Also easy to installe 62582



- Y00409

by: Gwyn04/22/2015


Yakima roof rack was very easy to install and looks great! etrailer.com was fast, efficient and very helpful! 187355



- Y00409

by: Casey W.06/27/2012


The service at Etrailer was excellent and the product I ordered was top quality. Very satisfied. 45837



- Y00409

by: brandon07/10/2015


Solid product from Yakima with the friendly staff of etrailer. extra length for more toys 210741



- Y00409

by: Jeff07/18/2013


The bars have not changed much over the years, but don't really need to. 90154



- Y00409

by: Jim07/09/2012


Fit my Ford Freestyle, easy install, fast safe delivery. Quality product. 47246



- Y00409

by: Tom B07/04/2014


Metal is too soft. The u-bolts from the cargo carrier cut into the rods 139209



- Y00409

by: john wright03/12/2012


I have installed on my Prius and it fit very nicely. I am well pleased 33650



- Y00409

by: William M10/31/2012


Good old Yakima. Always great quality with excellent instructions. 58511



- Y00409

by: Paul M04/02/2012


Worked on my 2003 Ford Excursion no problem. Done in about 20 min. 35922



- Y00409

by: CrossBars and towers06/15/2012


Great product, quick shipping, looked great and installed easily! 44325



- Y00409

by: Tom05/16/2012


Great Price. the best I could Find. Very Prompt delivery. 40747



- Y00409

by: Ronnie S07/02/2012


The rack fit perfect. Showed up quick. Nikki was great 46566



- Y00409

by: Carissa Swilley07/13/2012


Thanks for quick deliever and good prod uct. 47897



- Y00409

by: Tim H10/05/2012


Good Product Easy Install Thank You 56479



- Y00409

by: CM Hess10/15/2012


Great product and great service. 57231



- Y00409

by: Jose M03/23/2011


Excellent Service! 10204



- Y00409

by: pete t09/21/2012


Heavy Duty bars . 55378



- Y00409

by: Tom C03/21/2011


Asadvertised. 9928



- Y00409

by: ernie p01/26/2012


great racks 30419



- Y00409

by: Tommy M06/07/2013


Great 83758

51
51


Ask the Experts about this Roof Rack


  • How To Reduce Wind Noise Caused by Roof Rack on 2013 Honda Civic
  • When equipment is installed on the roof of a vehicle, wind noise will occur. It is unavoidable, but you can do certain things to minimize the noise. The round bars used with the Yakima rack system you mentioned can be quieted to some degree by using a fairing like part # Y07049. Keep in mind, the fairing will help streamline the rack itself, but whatever is placed on the crossbars like a cargo basket, box or ski rack will cause further turbulence and therefore noise. Using a Aero-style
    view full answer...

  • Roof Rack Options for 2013 Hyundai Santa Fe With Panoramic Sun Roof
  • You are correct that the discontinued Rola Roof Rack # 59765 was a fit for your 2013 Hyundai Santa Fe with panoramic sunroof. The other Rola rack you referenced, # 59790, is not a fit for your 2013 Santa Fe. Our contact at Rola advised that they have a replacement for the discontinued rack, part # 59779, which will fit the Santa Fe with a naked roof. We do also have other options for you and these will vary depending on which specific version of the Santa Fe you have; Hyundai offered
    view full answer...

  • Roof Racks for 2015 Ford Edge with Panoramic Vista Roof
  • We do have plenty of choices in roof racks for your 2015 Ford Edge with Vista roof. Just click on the link provided and select your roof style, flush rails or a bare roof, at the top of the page. You'll then see the options for that roof style. If you happen to have the bare roof you can use Yakima's round bar rack system consisting of parts # Y00409, # Y00124, # Y00664 and # Y00731. You'll also want to get the end caps # Y8007026 for a nice neat appearance. If you have the flush
    view full answer...

  • Can Thule Cargo Boxes Fit Yakima Round Cross Bars
  • Yes, Thule roof cargo boxes will attach to round Yakima crossbars. It looks like you have a 2011 Toyota Prius with the Yakima roof rack that consists of # Y00409, # Y00699, # Y00605, and # Y00124. For a smaller cargo box that would fit this rack I would recommend the Thule Force part # TH624. I attached a review video that shows this box being demoed on a similar Prius as yours.
    view full answer...

  • Using Longer Than Recommended 58 Inch Yakima # Y00409 Crossbars on 2009 Kia Optima
  • As long at the crossbars you use aren't wider than the widest part of the vehicle, which could be a safety problem, you could certainly use the 58 inch crossbars instead of the 48 inch ones. According to my research, the 2009 Optima is about 71 inches wide at it's widest point. Using a 58 inch crossbar would be just fine. The rack capacity is 100 lbs, but keep in mind you might be limited by the actual capacity of the roof, if it's less. Your owner's manual or Kia dealer should be able
    view full answer...

  • Roof Rack and Kayak Carrier Recommendation for a 2012 Ford Focus.
  • We carry many roof rack and kayak carrier options for your 2012 Ford Focus. The roof rack that I would recommend is the Yakima Q Tower roof rack that includes two 58 inch crossbars, # Y00409, the Q5 Q Clips, # Y00605, the Q83 Q Clips, # Y00683, and the Q Tower Feet, # Y00124. This will provide you with two crossbars to mount your kayak or kayak carrier to. I have attached a link to all of the roof rack options that will fit your vehicle for you to check out. You can mount your kayak
    view full answer...

  • Will the Yakima Q Tower Roof Rack Support an Extension Ladder on a 2013 Scion xB
  • You can carry an extension ladder on your 2013 Scion xB with the Yakima Q Tower Roof Rack, but there are a few factors you will want to take into consideration. Once this roof rack is installed, you will have a crossbar spread of 45 inches. The crossbar spread is the distance from the center of the front crossbar to the center of the rear crossbar. The most important factor to consider is the weight of the ladder. The Yakima Q-Tower crossbars have a weight capacity of 165 lbs, however,
    view full answer...

  • Recommended Roof Rack for 2013 Wrangler 2 Door with Hard Top
  • The easiest solution would be to assemble a roof rack using the following parts from Yakima: 58 Inch Long Round Crossbars, part # Y00409 Yakima 1A Raingutter Towers, part # Y00101 Once the crossbars are in place, the Thule Flat Top Ski and Snowboard Carrier you already have will attach directly to the crossbars. When used on a Wrangler Hard Top, the drip rails that the roof rack towers attach to have a limited carrying capacity. Yakima recommends carrying skis or snowboards only,
    view full answer...

  • Will 50 Inch Thule Load Bars Fit Instead of 58 Inch Yakima Cross Bars for 2010 Toyota Prius
  • I used our Fit Guide to determine which cross bars will work for your 2010 Toyota Prius. I found that the 50 inch Thule Loadbars, part # THLB50, will fit your 2010 Toyota Prius, if you do not have a glass roof. If there is a glass roof, you will need to go with the 58 inch Yakima Crossbars. Also, the 48 inch Yakima Crossbars, part # Y00408, will not fit your 2010 Toyota Prius. If your vehicle does not have the glass roof, and you decide to use the Thule Loadbars, part # THLB50, you will
    view full answer...

  • Using 48 Inch Long Crossbar With Yakima Roof Rack Installed on 2014 Ford Focus
  • I spoke with my Yakima representative, who tells me that they recommend the longer 58 inch crossbar and that a 48 inch bar hasn't been tested and therefore they don't recommend using bars that short. I've provided an install photo showing the 58 inch bar installed. As you can see, there's not much overhang. I doubt the 48 inch bar would be long enough. I don't believe you'd be able to use those shorter bars on a 2014 Focus. I wish I had better news for you.
    view full answer...

  • Roof Rack Recommendation for a 2016 Ford Mustang
  • For a roof rack confirmed to fit your 2016 Ford Mustang you would want the Yakima part numbers # Y00409, # Y00124, and # Y00678.
    view full answer...

  • Yakima Roof Rack Recommendation for a 2014 Wrangler Unlimited
  • For your 2014 Jeep Wrangler Unlimited Yakima recommends the use of their Yakima 1A Raingutter Towers # Y00101. There is no way to install a Q-tower setup on your vehicle. You still will be able to use your round crossbars if you happen to have them still and they are at least 58 inches long like the part # Y00409.
    view full answer...

  • Roof Rack for 2014 Ford Transit Connect Titanium
  • As long as your Transit Connect has the roof mounted rails that run front to back along the edges of the roof, the Yakima RailGrab Roof Rack consisting of the # Y00409 crossbars and # Y00138 RailGrab towers is indeed a fit for your vehicle. According to Yakima, all models of the Transit Connect are equipped with the roof rails I mentioned, so you should be good to go.
    view full answer...

  • Roof Rack Recommendation for a 2013 Jeep Wrangler Unlimited
  • We have a few different roof rack options for your 2013 Jeep Wrangler Unlimited. Two roof racks that I recommend looking at is the Yakima round bar roof rack or the Thule square bar roof rack systems for hardtops. It appears that your Jeep has a hardtop in the photo you provided. The Yakima roof rack consists of the following: 58 inch round crossbars # Y00409 Yakima 1A Raingutter Towers # Y00101 The Thule roof rack consists of the following: 58 inch square crossbars # THLB58 Gutter
    view full answer...

  • Recommended Roof Rack For 2012 Toyota Highlander With No Side Rails
  • I called my contact at Yakima about your 2012 Highlander. They told me the 4 points you said that are on your roof are actually there if you would decide to have the raised side rails installed and are not used as mounting points for a roof rack. The Yakima roof rack we have that is a confirmed fit for your Highlander has three components. To order this roof rack you would need part # Y00409, part # Y00124, and part # Y00699.
    view full answer...

  • Roof Rack and Kayak Carrier for a 2014 Jeep Wrangler Unlimited Hard Top
  • The gutter mount roof racks such as the Yakima system are not likely to hurt the hard top roof on your 2014 Jeep Wrangler Unlimited. The rain gutter area where the feet install is the strongest part of the roof so no worries! Yakima indicates that with their rack you can only carry skis and snowboards. So I recommend the Thule roof rack using gutter feet # TH300 and load bars # THLB58. Then you can use a kayak carrier such as a the sTACKER # TH830. I have linked videos on the roof rack
    view full answer...

  • Roof Rack Recommendation for a 2013 Kia Soul With a Naked Roof
  • You definitely have a lot of options that are substantially less than what your husband was quoted to have a quality roof rack for your 2013 Kia Soul with a naked roof. The first roof rack system I would recommend would be the Thule Square Load Bar System # THLB50. These square bars can hold just about any roof top accessory on the market and are made in the USA, and are constructed of galvanized steel. I have attached a brief video of this system on a 2013 Kia Soul. If you would
    view full answer...

  • Recommended Roof Rack for 1998 Chevrolet C/K Series Pickup with Extended Cab
  • My contact at Yakima confirmed that their roof rack system you referenced does not fit your 1998 Chevrolet C/K Series 3-door pickup with extended cab. They have no custom-fit racks for your truck. However, we do offer a direct-mount track-type roof rack system from Rhino-Rack, their RT-Style Roof Rack Tracks # RTS507 that can be riveted directly to your cab's roof. Pop rivets are included and a rivet gun is required to install them but you could certainly select alternate hardware.
    view full answer...

  • Recommended Roof Rack And Bike Carrier For 2015 Scion tC
  • The roof rack we have that is designed for a 2015 Scion tC is the Yakima Q Tower roof rack. This roof rack is for all models of the tC that have no existing rails or crossbars. For this roof rack you will need part # Y00409, part # Y00124, part # Y00699, and part # Y00728. Thule does not have a roof rack that is designed to fit the 2015 tC. The bike rack I recommend is the Yakima HighRoller Roof Bike Rack, part # Y02107. This bike carrier allows you to keep the front wheel on
    view full answer...

  • Will Yakima 48-Inch Roof Rack Crossbars Fit the 2013 Dodge Dart
  • The Yakima roof rack components that you referenced, parts # Y00409, # Y00702, # Y00606 and # Y00124, make up a complete rack system that fits the naked roof on your 2013 Dodge Dart. The crossbars in this system, part # Y00409, are 58-inches in length. Installation of this system on your vehicle is shown in the linked video. Crossbars that are 48-inches will not be long enough for your vehicle. The shortest crossbars that will work on your Dart are the 53-inch size that are part of the
    view full answer...

  • Recommendation for Wind Noise Prevention for Yakima Roof Rack on 2012 Jeep Grand Cherokee
  • To help prevent wind noise created by the Yakima roof rack you installed on your 2012 Jeep Grand Cherokee, I recommend the Yakima Windjammer Airfoil # Y01115. It is a small, wing shaped airfoil that serves as a low-cost alternative to fairing. It installs in seconds over the front crossbar and reduces rack noise. I have included a video review and description of this product. It is 1-1/4 inches tall by 3-3/4 inches wide by 8 inches long and comes with a lifetime warranty. I have included
    view full answer...

  • Which Q Clips are the Front for Installing Yakima Roof Rack on a 2012 Jeep Grand Cherokee
  • For installing a Yakima roof rack on your 2012 Jeep Grand Cherokee the Q10 Clips part # Y00610 go in the front and the Q5 clips part # Y00605 go in the rear. The rest of the components needed are the Q Towers part # Y00124 and crossbars # Y00409. I also attached an install video for this rack on a 2012 Grand Cherokee just like yours.
    view full answer...

  • What Roof Rack Can Carry Surfboards on a 2013 Scion tC
  • We do offer a Yakima Roof Rack System for your 2013 Scion tC that consists of four components, including the Q99 Q Clips, part # Y00699. The other components are 58-inch round crossbars, part # Y00409; the Q128 Q Clips, part # Y00728; and the Q Tower Roof Rack Feet, part # Y00124. I have included a link to our product page showing all of these components. I have also provided a link to an installation video. Please note that the sun/moon roofs cannot be opened when the rack is in place
    view full answer...

  • Do Yakima Q Clips for Roof Racks have a Part Number On Them
  • The best way is to ask me! On the 2011 Hyundai Elantra Touring models the front and rear Yakima Q Clips are Q99 clips, # Y00699. If you take the clips off of the vehicle the number clip it is will be stamped into the clip, like in the picture I have included.
    view full answer...

  • Replacement Parts for Yakima Q Tower Roof Rack on 2005 Toyota Corolla
  • Yes, we can help you! For your 2005 Toyota Corolla's Yakima roof rack you will use Q99 front clips # Y00699 and Q31 rear clips # Y00631; order one set of each. The Q31 kit includes two of the correct pads so you'll have a spare. You might care to refer to the linked installation video.
    view full answer...

  • Roof Rack Recommendation For 2002 Honda CR-V
  • Your 2002 Honda CR-V has fixed mounting points on the roof so all of the roof racks we offer are designed to be installed using those attachment locations. We do not offer any roof racks that attach to the door jambs of your CR-V. I recommend the Rhino-Rack Vortex Aero roof rack. This has 49 inch aerodynamic crossbars that are extremely quiet. To get this roof rack system you will need to order three parts. They are part # RRVA126B-2, part # RRVA-FK2-2, and part # RLCP01. I have attached
    view full answer...

  • Yakima Roof Rack for a 2004 Ford Mustang GT
  • We have not installed a Yakima roof rack on a 2004 Ford Mustang, but Yakima has. I included a pictured showing the rack installed. Bascially what will happen is that when the clips and feet are properly tightened down the clips will pull up and out of the way of glass window. The parts needed to install a Yakima roof rack are: Crossbars # Y00409 Q56 Clips, # Y00656 Q50 Clips, # Y00650 Q Towers, # Y00124 And if you wanted more space between the crossbars use the stretch kit # Y00134.
    view full answer...

  • Should the Yakima Bolt TopLoader, # Y08005, Be Mounted through the Roof or Sidewall of a Trailer
  • You should mount the TopLoader, # Y08005 and Q Towers, # Y00124 through the single-wall areas on the top (roof) and not the sidewall according to the Yakima instructions for the Bolt-On Top Loader. I have included a link to a video installation of a Yakima roof rack system below.
    view full answer...

  • Roof Rack Recommendation for a 2015 Toyota Prius
  • Yakima has a roof rack confirmed to fit your 2015 Toyota Prius without a sunroof. For that you would want the following components. Yakima Q Towers part # Y00124 Q99 Clips part # Y00699 Q5 Q Clip part # Y00605 44 inch Fairing # Y07048
    view full answer...

  • What Roof Rack Fits a 2008 Ford Ranger XLT 2-Door Supercab
  • The roof rack I recommend for your 2008 Ford Ranger XLT 2-Door Supercab is the Yakima system consisting of parts # Y00409, # Y00625, # Y00124 and # Y00134. This kit includes 58-inch round crossbars, Q-Towers, Q-25 Clips and the stretch kit to allow wider placement of the crossbars to help fit larger loads. Also, the round crossbars included in this rack offer the widest possible compatibility with accessory items. This Yakima system is intended specifically for the Ranger 2-door Super
    view full answer...

  • Will Yakima Q Towers Roof Rack Feet and Load Bars Fit on a 2010 Jayco J Series Pop Up Camper
  • Yes, you can use the Yakima Q Towers Roof Rack Feet for Naked Roof (QTY 4), # Y00124, on top of your 2010 Jayco pop up camper. First, you will need Bolt-On TopLoader Mounting Brackets for Yakima 1A Raingutter Towers, Q Towers, # Y08005, so you can mount the towers. These are sold in pairs so you will need two sets to install all four towers. You would then just need to add load bars depending on how wide your camper is. I have included a link to our Yakima load bar main page below.
    view full answer...

  • Availability of a Roof Rack for a 2009 Jayco Series 1006 Trailer
  • If your 2009 Jayco trailer has a fiberglass roof, you can first install Yakima tracks like # Y01135 (60 inches long), # Y01127 (54 inches long), or # Y01126 (42 inches long). Then, you can add LandingPad 1 for Yakima Control Towers, # Y00221, and Control Towers, # Y00214. You would then add Yakima crossbars of the width you need, like the 86 inch long bars, # Y00420. The cross bars are 58 inches wide and the tracks are 42 inches long. You will need to measure your trailer to make sure
    view full answer...

  • Recommended Roof Rack And Bike Carrier For 2016 Hyundai Veloster
  • Due to the body style of your Veloster the only system we offer that would allow you to carry two bikes is a roof rack and roof rack bike racks. We do not have a trunk-mount carrier that will work or a trailer hitch that will fit your Veloster. I recommend the Yakima Q-Tower roof rack. This roof rack features custom clips designed to fit the contour of your Veloster roof. To order this roof rack you will need part # Y00124, part # Y00699, part # Y00716, and part # Y00409. Next, you
    view full answer...

  • 2010 Camaro Roof Rack Recommendation for Carrying Kayaks
  • The correct roof rack for your 2010 Chevy Camaro consists of the Yakima Cross Bars # Y00409, Q-towers # Y00678, and the Q-Clips # Y0124. This roof rack will mount directly to your vehicle door frame and doos not require drilling for installation. If you would like locks for this roof rack you can use the Yakima Same Key System (SKS) # Y07202. With the above Yakima Roof rack system mentioned above your cross bar spread (distance from the center of one cross bar to the center of the other
    view full answer...

  • Complete Custom Fit Roof Rack System and Kayak Carrier for a 2004 Volkswagen New Beetle
  • The racks available for your 2004 Beetle have been tested on the actual vehicle they are made for. That is how the companies determine that they will fit. Everything you will need to install a roof rack on your 2002 V-dub New Beetle is included in the Yakima complete roof rack system (itemized below). You would then be able to add a kayak carrier like the Yakima HullRaiser J-Style Roof Mounted Kayak Carrier, # Y04039. For the Yakima kit you will need a total of 2 sets of Q123 Q Clips,
    view full answer...

  • Roof Rack Recommendation for a 2002 Ford Windstar
  • To install tracks in the grooves on the roof of your Windstar you will have to have a custom installation done. I checked with my contacts at Thule and Yakima and they do not offer a custom fit track for your vehicle at this time. Yakima has a system, if your 2002 Windstar has the dual sliding doors, that will provide crossbars for carrying cargo or bikes on the top of the vehicle. To install this system you will need 3 parts. Yakima Q Towers item # Y00124 Round 58" CrossBars for
    view full answer...

  • Recommendation for Bolt on Roof Rack System for 2008 Ford Ranger
  • Rhino Rack offers the RT-Style Roof Rack Track that would mount directly to the roof of your 2008 Ford Ranger with pop rivets. You will need a rivet gun to install this track so if you do not have one already, you could purchase one from a local hardware or auto parts store. We offer the # RTS507 which is our shortest RT track and it measures 43-1/2 inches long. These tracks are offered in different lengths and can be cut if necessary. You will want to measure the roof of your Ranger
    view full answer...

  • Roof Rack and Accessories to Carry Stand Up Paddleboard on a 2011 Chevy Camaro
  • Yes, there is a roof rack that will fit your 2011 Chevy Camaro. However the crossbars will be so close together (20 inches on center) that none of the stand up paddleboard carriers will work. But I think I have a solution that could work. You would start with the roof rack using the following parts: 58 inch crossbars # Y00409 Q Towers # Y00124 Q78 clips # Y00678 (you will need to order 2 of these to get 4) Then you could use pads # Y04070 that will go around the bars to product
    view full answer...

  • Does the Yakima Q Tower Roof Rack for 2014 Dodge Grand Caravan Include Locks
  • The Yakima Q Tower Roof Rack for the 2014 Dodge Grand Caravan consists of parts # Y00409, # Y00657 and # Y00124. This round crossbar system does not include the lock cores needed to secure it to your Grand Caravan but these are available as separate items. We offer the Same Key System (SKS) lock cores in various quantities: 4-pieces as part # Y07204 (enough for the rack itself) but also in a 6-piece set as part # Y07206 (enough for the rack plus some Yakima accessories). This system
    view full answer...

  • Fitting Of The Yakima Q Towers Roof Rack Feet, # Y00124, On A 2000 Mercury Mystique
  • On the Yakima Q Towers Roof Rack Feet, # Y00124, for the 2000 Mercury Mystique there is a footnote in the instructions. It says placement of the clips for this vehicle requires pulling a portion of the interior weather seal off from the door frame. Place the clips over the exposed steel ledge. Replace weather seal by pushing over clip and ledge. I have a picture of how to attach the clips under the weather seal. I will send the picture in a separate email. That might be what is
    view full answer...

  • Parts Needed to Add a Yakima Roof Rack to a 2014 Audi A4
  • The Q Clips for a Yakima roof rack are vehicle specific so they are not included with the Q Towers, # Y00124. For your 2014 Audi A4 you will need 48 inch bars # Y00408, 2 sets of Q5 Q Clips, # Y00605, and the Q Towers # Y00124.
    view full answer...

  • Yakima Roof Rack Recommendation for a 2009 Pontiac Montana SV6
  • Yes, the Yakima Q Towers # Y00124 that you referenced would be a component for a roof rack that is confirmed to fit your 2009 Pontiac Montana SV6. To complete the roof rack you would need the following components as well: Round 48 inch Cross Bars # Y00408 A quantity of (2) Q Clips # Y00729 I attached an install video and installation instructions for this product for you to check out also.
    view full answer...

  • What is the Yakima Roof Rack Weight Capacity for a 2010 Nissan Altima Sedan with Sunroof
  • According to Yakima when using their roof rack system on a 2010 Nissan Altima the capacity is 100 pounds. You can consult the vehicle owners manual and/or Nissan to confirm the roof weight carrying capacity. If it is different than 100 pounds go with the lower rating. You will need the following parts to install the roof rack: 48 inch crossbars # Y00408 Q Towers # Y00124 Q96 front clips # Y00696 Q35 rear clips # Y00635
    view full answer...

  • Aftermarket Roof Rack Recommendation for a 2014 Infiniti QX60
  • I checked and Yakima has a fit for the roof of your 2014 Infiniti QX60 with a factory roof rack to install their round bars. You will need the following products: Q-Towers # Y00124 Q127 Clips # Y00727 Q116 Clips # Y00716 58 inch Round Bars # Y00409
    view full answer...

  • Kayak Carriers for a Yakima Roof Rack on a 2010 Chevy Camaro
  • I do have a solution for you but none of the Yakima kayak carriers will work with the roof rack on your 2010 Chevy Camaro. The issue is that the crossbar spread (center to center distance from one bar to the other) is only 20 inches. You would need at least 24 inches. You can't change the position of the bars on the roof since the parts are contoured to match the roof line. What you would have to do is use foam blocks # SR5525, one set for each kayak. And there will need to be enough
    view full answer...

  • Roof Rack Components For 2008 Honda Accord
  • We do sell the roof rack components for the Yakima system that will fit your 2008 Honda Accord with a naked roof. Just for information this system is designed to use crossbars that are 58 inches long. You will need to order 3 different numbers to complete the roof rack system. You will need part # Y00702, part # Y00665, and part # Y00124. This will give you the custom clips that attach to the doorframe of your Accord and the feet that the crossbars are attached to. To cut down on
    view full answer...

Yakima Carriers

Fit to this rack on your 2013 Dodge Durango

Info for these parts were:


Expert Research:
Michael L

Video Edited:
Zack K

Written by:
Tyler C

Expert Research:
Michael H

Expert Research:
Reno H

Expert Research:
Jameson C

Video Edited:
Joshua S

Video Edited:
Jacob T

Expert Research:
John H

Video by:
Patrick B

Expert Research:
Adam R

Video Edited:
Kathleen M

Video Edited:
Dustin K

Test Fit:
Sabrina B

Expert Research:
Lori W

Expert Research:
Jeffrey L

Video Edited:
Sue W

Test Fit:
Randy B

Video Edited:
Chris R

Test Fit:
Jared G

Photos by:
Theodore B

Expert Research:
Brandon M

Test Fit:
Joe V

Test Fit:
Patrick B

Test Fit:
Rick A

Photos by:
Jackie C

Expert Research:
Robert G

Expert Research:
Jeff D

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.








Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviews etrailer.com reviews

All images, layout and content copyright etrailer.com