Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Tekonsha PowerTrac Electronic Brake Controller - 1 to 2 Axles - Time Delayed
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti
Part Numbers: 39523, 3050-P
Retail:$78.77
Price:$74.94
Shipping SpecialTekonsha PowerTrac Electronic Brake Controller - 1 to 2 Axles - Time Delayed
part number: 39523
Easy-to-use brake controller activates your trailer brakes electronically when you engage the brakes in your tow vehicle. Set braking intensity to your preference and towing application.
Features:
- Brake controller activates electric trailer brakes (sold separately)
- Signal is sent to trailer brakes when tow-vehicle brakes are activated
- Adjustable output control lets you determine the amount of braking force
- Set to maximum when you travel through hilly terrain with your fully loaded trailer
- Back off the power output when you tow a lightweight trailer
- LED indicator on front of unit
- Green light indicates that brakes are connected
- Color changes to orange and then to red as the power output increases
- Built-in manual override
- PowerTrac can be used with trailers that have up to 2 axles (4 brake assemblies total)
- Mounting bracket and hardware included
- No need to mount level
- Additional pigtail harness (sold separately) or plug-in, vehicle-specific brake-control adapter (sold separately) can be used for certain applications to further reduce installation time
Specs:
- Dimensions: 3" wide x 5" long x 1-1/4" tall
- Limited 5-year warranty
Unlike pendulum-style controllers, which react to the inertia that is created by your tow vehicle slowing down, the PowerTrac applies your trailer's brakes when the brake pedal in your tow vehicle is engaged. The trailer brakes will be activated with an intensity set by you. This output (amount of braking power) is adjustable to suit your preference, as well as road conditions, type of trailer and load. You can also apply the brakes manually with the integrated override.
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. As a result, mounting options are nearly limitless. After mounting the unit, hardwire the end of the included pigtail harness directly into your vehicle. For even easier installation, a vehicle-specific wiring adapter (sold separately) is available for certain vehicles. One end of the custom adapter plugs into your vehicle, and the other end plugs into your controller - no hardwiring required. To transfer the PowerTrac to another vehicle or to remove it for storage, just unplug the unit and remove it from the mount.
Note: For vehicles without brake-control wiring adapters, a 20-amp circuit breaker (9506P - sold separately) is required.
See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) that includes all the parts necessary to install the PowerTrac brake controller.
80500 Tekonsha PowerTrac Electric Brake Control
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti
part number: 3050-P
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the junction box beneath your vehicle's dashboard.
Features:
- Wiring adapter eases installation of your electric brake controller
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
- Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
- Limited 1-year warranty
Installation of Tekonsha Brake Controller Adapter
This adapter plugs into the 6-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
3050-P Tekonsha Brake Control Wiring Adapter with 2 Plugs
Video of Trailer Brake Controller Installation - 2011 Nissan Pathfinder
Video Transcript for Trailer Brake Controller Installation - 2011 Nissan Pathfinder
Today in this 2011 Nissan Pathfinder we're going to install part number 39510 from Tekonsha. This isthe Voyager trailer brake controller.This vehicles already been equipped with a 4-pole wiring packaging from the factory. To add ourbrake controller and connector, we're basically going to just fill in the blanks. We're going to start offunderneath the dash. We're going to locate the tow package port underneath the dashboard whichis going to be just right of the steering wheel, behind the dash, and also a little bit above thediagnostic port.We'll go ahead and take the adapter cord and plug it into the brake controller, and then we'll goahead and plug it into the port underneath the dash. The part number for our adapter cord will be3050-P.
With all the brake controller wires plugged together, we'll go ahead and add the bracket tothe dashboard underneath. We're going to locate it next to the diagnostic port, just a little bit to theleft of it. We'll use two screws to attach the bracket to the dashboard.Next we'll pre-drill the holes in our brake controller to accept the hardware; we'll install the brakecontroller to your bracket using four more screws; and then we'll go ahead and take a moment to ziptie our wires and make sure they're safe and out of the way. Then we can go to the back of thevehicle. Thats where we're going to go ahead and add our 7-pole connector to the back of thevehicle.
Thats going to be part number 37185. We're going to take the bracket and hold it to thebottom of the hitch. Theres an existing weld nut we're going to use to fasten it to the hitch. We'llhold it up there, make a mark on the bracket, and then we'll go ahead and drill it out to a 3/8 hole.We'll take our bracket back to the vehicle and attach it to the hitch, using an 8 mm bolt, the 1.25thread hitch; then we'll go and add our 7-pole connector. On the 4-pole end of it we're going toapply some dielectric grease and then attach it to the factory 4-pole.
We're going to run a zip tiethrough the wires to make it a semi-permanent connection. We'll take a moment to tape up ourwires and also add our loom material to help protect some of the wires and make it look nice.At this point we'll go ahead and connect the 7-pole to the bracket, and then we're going to add alength of wire to it about 3 or 4, part number 10-2-1. We'll cut the sheath back and we'll have ablack and a white wire. We'll run our black wire to the black wire on the 7-pole connector and ourwhite wire to the blue wire on 7-pole connector. We'll crimp those down and then use some tape tohelp protect them.There are two remaining wires left.
Therell be a white wire for the ring terminal and a purple wirefor the buck connector. We're going to tape those two wires to our grey cable, and we'll run thosewires along with the grey cable. Now we're going to route our cables over to the end of the towpackage which is located next to the spare tire. We'll measure a length of a grey duplex cable weneed and cut the excess off; then we'll strip back to the sheath of the grey cable, exposing the wireswe'll need later. Then we can take the white wire with your ring terminal and ground it to the frame.The self-tapping screw we'll be using will be part number SA1131822.We're going to look for a connector thats at the end of our tow package. We've got a smallconnector with two wires going to it. There will be a brown wire and a purple wire going to it. Now,we dont have a connector to match that, so well rotate the connector and remove it from thewires; then we'll go ahead and crimp our wires from our grey cable to those two wires. We'll use abuck connector to make those connections. Our part number for our buck connectors we'll be usingwill be part number 05732-2.We're going to connect this as follows. Our white wire which will be our brake controller output isgoing to connect up to the brown wire; and then our other wire, a black wire, will connect up to thepurple wire. Thatll be our 12 volt power supply. We'll go ahead and tape up our connections and ziptie our wires safe and out of the way.All our connections are done at the back of the vehicle; now we'll go underneath the hood and wehave to add one relay to power our 12 volt power supply. Theres a relay box closest to the battery.We'll remove the lid and you'll see that theres two relays already installed, and therell be an opensocket for an additional relay. We'll install the relay for our 12 volt power supply, and thats going tobe part number V38937-1.With all of our connections made, we'll go ahead and test out the brake controller. We'll plug atrailer into it and you'll see that the LED on top will turn from off to a green color; and then we'll usethe manual override. You'll see that goes from a green, to a yellow, to a red that shows the manualoutput works. Now we'll go ahead and try the foot brake. We have to make the level in the brakecontroller a little bit more aggressive, so we can see it work. Push down the brake pedal and you cansee that turns from a green to an orange.And with that, thatll finish it for our install of our Voyager brake controller on our 2011 NissanPathfinder.
Ask the Experts about this Brake Controller
Do you have a question about this Brake Controller?
- Tekonsha Powertrac 2-4 Electric Brake Controller on a 2007 Chevy Tahoe
- Yes, your brake controller can be installed on your 2007 Chevy Tahoe. As long as the controller is functioning properly, it will wire the same as any other brake controller. There is no plug present under the dash, but the wires are already there. You only need to splice the brake control wires together with those already present under the dash. These wires are tied up with white tape to the left of the brake pedal. You need to connect 4 wires to the controller, as follows; red (12v power feed)
view full answer... - Availability of Brake Controller Harness for 2001 Toyota Tundra
- If you are looking for a brake controller harness, there are none available for the 2001 Toyota Tundra. The 2001 Tundra did not have factory tow packages as an option, so a brake controller will have to be hard wired into the vehicle.
You will need part # ETBC7 to create a 7 way plug at the rear of the truck. I will include a video on this kit. You will also need to install a 4 way connector. Toyota put the provision in for this so you will need part # 118378.
Once you have these parts in
view full answer... - Will a Brake Controller Draw Enough Power When Not in Use To Drain a Car Battery
- The brake controllers available now either are only on when they are activated, or a have a timed shut-off or idle state after a certain time period. Some of the older brake controllers never shut-off, but they did not drain battery power as the only component that would be on is a low amperage LED indicating that the controller has power or whether or not it was connected to a trailer.
As long as you have a healthy battery, you should not have a problem. Since your car is only 2 maybe 3 year
view full answer... - Adjusting Prodigy Brake Controller For Maximum Braking On a 1500 Pound Camper with a 1999 Ford F-150
- There are a number of factors to address if you feel that the trailer brakes on your camper are not performing to expectations. The first thing I would check is the mounting and leveling of the brake controller. The Prodigy must be mounted from 0 degrees to 70 degrees nose up but cannot be mounted canted to the right or left. Once mounted correctly the Prodigy, item # 90185, will acquire the level setting and you will need to adjust the power. If you have the power set to full and the trailer br
view full answer... - Trouble Shooting Tekonsha AccuTrac Brake Controller Not Recognizing Trailer on a 1999 Ford F-150
- I spoke with my co-worker, Bob, about this for some time this morning. We are both thinking you have a ground issue somewhere or possibly a short. Between the trailer brakes and the brake controller there are several grounds that need to be checked. I will start at the top and work down one by one till we can find the source of the problem. Some of this may be redundant so bear with me.
I assume you mean that the green light does not come on when the truck is on and the trailer is connected.
view full answer... - Brake Controller Not Functioning Properly On a 2004 Chevrolet Pickup When Brake Pedal is Pressed
- It sounds as if you may have the incorrect brake controller wiring harness. The correct wiring harness for the 2004 Silverado 2500 HD is the Universal Brake Control Wiring Adapter 2003 - 06 Chevrolet, GMC, Cadillac, item # 20264. Unplug the harness and check the wire locations in the connector.
When holding the connector with the locking tab in the down position the red wire should be in the bottom right position closest to the locking tab. If the red wire is in the top left position, farthes
view full answer... - Looking to Upgrade the Brake Controller On a 2004 Silverado 1500 for Towing a 2010 Outback Trailer
- The Prodigy P-3, item # 90195, is definitely an upgrade from the Hayes-Lemmerz Energize III Electric Trailer Brake Controller, item # 81741B. You would definitely see an improvement in the braking performance and a reduction in the delay you are experiencing with the Energizer controller.
The P-3 uses an accelerometer to detect how fast the vehicle is slowing and apply the correct amount of power, based on user settings, to the trailer brake magnets. This system is almost seamless with the ve
view full answer... - Can You Give Detailed Step By Step Instructions For Brake Controller Install On 2001 Toyota Tundra
- To install a brake controller on your vehicle you will need Brake Controller 7 & 4 Way Installation Kit, part # ETBC7 and the Tow Ready Custom Fit Vehicle Wiring, part # 118378 on your 2001 Toyota Tundra.
If your 2001 Toyota Tundra has an existing 4-way connector, you will not need to install part # 118378.
For installation of part # 118378, start by disconnecting the negative terminal on the battery and remove the battery hold down bracket and slide the battery towards the motor. Next,
view full answer... - How to Adjust the Power Trac Brake Controller on a 2004 Grand Cherokee Overland with AccuTrac
- It sounds as if you will need to adjust the power settings on your brake controller. There is only one adjustment on the Tekonsha Power Trac Brake Controller, item # 39523. It is the power gain setting and should be adjusted so the trailer brakes are close to but do not lock up, with each different load on the trailer.
The Power setting is turned up and down to increase or decrease the amount of power sent to the trailer brakes. If you have the power setting set too high on a time delayed con
view full answer... - Can the Tekonsha Powertrac Trailer Brake Controller # 39523 be Installed on a 2010 Toyota Tundra
- Yes, you can install the Tekonsha Powertrac, # 39523, in your 2010 Toyota Tundra. There are 2 ways you can wire in the brake controller. If the harness that came with the truck has blunt cut wires at the end that connects to a brake controller, you will need to match the wires on the brake controller to the functions on the harness as follows:
White on brake controller ground
Black on controller = 12 volt power
Blue on controller = out put to trailer brakes
Red on controller = in from sto
view full answer... - Troubleshooting a Tekonsha Powertrac Brake Controller # 39523
- There should not be 12 volts coming out of your ground terminal (7:00) on your vehicle connector. That sounds like where your problem is located. It sounds as if the 12 volt accessory that should be in the 2:00 position of your connector has been mistakenly wired to your ground circuit.
I attached a picture of how the connector on your tow vehicle should be wired by function for you to check out. I also attached an FAQ page on trailer wiring that you might find helpful.
view full answer... - Troubleshooting Fading Brake Output with Tekonsha Powertrac Trailer Brake Controller # 39523
- I spoke with my contact at Tekonsha about the Powertrac Brake Controller, # 39523. She stated that if the testing you are doing is with the vehicle and trailer parked, when you step on the brake or use the manual override, the output will go to the preset limit, but then, since the voltage is not needed, it will fade out. When moving the voltage will stay applied.
She also suggested testing the blue output wire using a test light like # 3808 while stepping on the brake. Having the testing lig
view full answer... - Using Wire for Bed Cap 3rd Brake Light Instead of Brake Stoplight Switch to Install Brake Controller
- As long as you have verified that the wire in question only goes hot when the brake pedal is applied, there is no reason why you cannot use the wire intended for the bed cap third brake light. If you do not have a circuit tester, we offer one, part # 3808.
Certain vehicles (like GM trucks produced in the late 1990s) had brake switch wiring that was very difficult to access. In those instances, we typically recommend doing exactly what you propose.
view full answer... - Finding Correct Brake Stoplight Switch Circuit to Install Brake Controller on 2004 Toyota Highlander
- I do not have any specific information about the color of the wire you are looking for, but I can describe how to find it.
Use a circuit tester like part # 40376, and probe each wire coming off of the brake stoplight switch. As you probe each wire, press the brake pedal. Once you find the circuit that only shows current when the brake pedal is pushed, tap the red controller wire into it.
view full answer... - Tekonsha Power Trac Brake Controller # 39523 No Longer Applying Brakes When Brake Pedal Pushed
- It sounds as if you might try to adjust the power settings on your brake controller. There is only one adjustment on the Tekonsha Power Trac Brake Controller, part # 39523. It is the power gain setting and should be adjusted so the trailer brakes are close to but do not lock up, with each different load on the trailer.
The Power setting is turned up and down to increase or decrease the amount of power sent to the trailer brakes. If you have the power setting set too low on a time delayed cont
view full answer... - Light Does Not Come On when Tekonsha Pod Trailer Brake Controller is Installed on a 2010 Ford F-150
- The first thing I reocmmend is to connect a trailer to the vehicle. The light will not come on if a trailer is not connected. If you do connect a trailer and the light does not come on it could indicate a few different issues.
First, check the black wire behind the controller for voltage. If there is no voltage going to the controller it will not turn on. You will need to check the fuses associated with the tow package to determine if something is blown or missing.
You may also have an op
view full answer... - Is a Brake Controller Plug and Play Wiring Harness Available for a 2003 Mercedes ML 350
- There is not an aftermarket plug and play brake controller wiring connector available for the 2003 Mercedes ML 350. You may be able to purchase one from the vehicle dealer though.
I spoke with my contact at Tekonsha and his advice is that you should take your Mercedes M Class vehicle to the dealer to have a brake controller installed. The Mercedes vehicles have very sensitive wiring and splicing into the brake circuit or power on the vehicle can cause issues.
If you have wiring experience
view full answer... - Brake Controller Power and 12 Volt Hot Lead Fuse Locations on a 2011 Chevy Tahoe
- Most vehicles are already equipped with the fuses mentioned in the video, which is what we have come across. If your vehicle does not have one or both fuses, you will need to insert your own fuses. To find the correct locations, you can look at the legend on the inside cover of the power distribution box.
Sometimes, the locations are the ones closest to the terminals. In this case they are slightly off to the right (driver side) as you can see in the video I have linked at about the 5:25 mar
view full answer... - Replacing the Manual Slide Knob on a Pod Brake Controller and Troubleshooting No Green Light
- I made you a short video that shows how to replace the knob provided that the little tabs on the back of the knob or where they mount are not damaged.
When you do not get a green light, that means that the trailer is not connected, there is a short to the brake output wire, or there is a bad ground connection. It could also mean that there is no power going to the controller black wire. Use a circuit tester like # 3808 if needed to determine if power is on the black wire.
Then, sever the
view full answer... - Will the Pod Trailer Brake Controller Fit a 2005 Dodge Ram 1500
- The Pod brake controller, # 39523, does come up for a 2005 Dodge Ram. Depending on how the truck is equipped, you will also need 1 of 2 harnesses. If the truck came with a factory 4 or 7-Way trailer connector, you will also need wiring harness # 3020-P. If the truck did not come with a trailer connector, you will need # 20127. I have included links to a couple of videos that should help.
view full answer... - Nissan Xterra Brake Controller Adapter
- The product you referenced, 3050-P, is vehicle specific and will not work with your Xterra. Your vehicle needs to be hardwired to use an electric brake controller. The 3050-P is only for vehicles pre-wired to accept a brake controller.
If you only need the Plug In Harness for the Tekonsha brake controller, product number 20127 will work for your vehicle. If your require the entire harness, you will need product ETBC7 and the wiring harness with the 4-Pole trailer connector, product number 43
view full answer... - Troubleshooting Brake Controller Installed on 2004 Nissan Titan
- If the display of your brake controller is not showing any indication that the unit is receiving power, use a volt meter or circuit tester like part # 40376 on the black wire feeding the controller to ensure the controller is not getting power. If you show no power on that wire, check your # 3050-P wiring adapter to ensure it is fully inserted into the connector under the dash. The connector on either side of the adapter should plug into place until it clicks.
If this checks out okay, you mos
view full answer... - Mounting the Tekonsha Prodigy Brake Controller on a 2010 Nissan Frontier
- Your Prodigy brake controller, # 90185, can be mounted between 0 degrees (level) and 70 degrees (facing up), or anywhere in between. As long as the brake controller is within the appropriate range, is mounted in an easily accessible location, and the harness will reach on your 2010 Nissan Frontier, it will work. It does not have to be under the dash on the right of the steering column.
It will not work properly if it is mounted tilted left or right or if it is not parallel to the direction o
view full answer... - Parts Needed for Installation of the Tekonsha P-2 Brake Controller on a 2010 Nissan Titan
- Yes, you will need the Tekonsha Wire Harness for Nissan, item # 3050-P, to plug the P-2 Brake Controller, item # 90885, in under the dash on your 2010 Nissan titan.
If your vehicle is not equipped with a factory 7-Way connector at the rear of the vehicle you will also need to install the Factory Style 7-Way and 4-Way Flat Vehicle End Trailer Connector, item # N40975, which comes with the needed relays for vehicles without the towing package, see video.
The brake controller and harness can
view full answer... - Connection Point for Tekonsha Brake Controller Wiring Harness # 3050-P, 2004 and Newer Nissan Titan
- The Tekonsha Brake Controller Wiring Harness, # 3050-P, that fits the 2004 and newer Nissan Titan plugs into a harness that is already on the vehicle. This harness will be located under the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
The wiring functions of this harness are as follows:
White = ground
Black = 12 volt power
Blue = brake controller output
Red = stop light
view full answer... - Brake Controller Wiring Harness # 3050-P Recommendation for a 2011 Nissan Xterra
- I spoke with my contact at Tekonsha and she informed me that the Tekonsha Brake Controller Harness, part # 3050-P that you referenced will work on your 2011 Nissan Xterra to allow you to connect your brake controller to the 7-way wiring that is on your vehicle.
The harness will be located underneath and left of the steering column, taped to another harness near the emergency brake pedal. It is a 6-pin connector that mates with the 3050-P brake control wiring adapter.
If you need a brake c
view full answer... - Can the Tekonsha P3 Trailer Brake Controller be Set Up without Having a Trailer Connected
- Yes you can setup the Tekonsha P3, # 90195, without a trailer connected. However, you will most likely need to do some fine tuning once a trailer is connected to get the proper amount of power back to the brakes for the particular trailer and load you are towing.
The first thing to do before even setting the power output is to make sure the controller is mounted properly in the vehicle according to the installation instructions which I have linked for you. If the controller is not mounted wi
view full answer... - How Long is the Electric Brake Controller Pigtail Adapter For Tekonsha Brake Controllers
- I went out to the warehouse and pulled the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers, # 3050-P and found that it is 31-3/4 inches long overall, including the connectors. I produced a short video showing the length of the adapter for you.
The # 3050-P harness is compatible with the Prodigy 2, # and all of the Tekonsha brake controllers in current production.
At this time the manufacturer lists this harness for the 2004 - 2012 Nissan, Armada, All Styles. This could chan
view full answer... - Where is the Factory Brake Controller Plug Located on a 2011 Nissan Titan
- The factory trailer connector on a 2011 Nissan Titan will be located underneath the dash and left of the steering column, taped to another harness near the emergency brake pedal. There will be a 6-pin connector that mates with the one on the adapter.
view full answer... - Brake Controller and Harness Recommendation for a 2012 Nissan Xterra
- I would recommend you go with the Prodigy P2 Brake Controller # 90885 and the 3050-P harness that you referenced. The P2 is one of our best selling controllers because of how easy it is to setup and how well it works.
The # 3050-P will simply plug into the back of the brake controller and then plug into the port under the dash.
view full answer... - Parts Needed to Add a Trailer Brake Controller and 7-Way Connector to a 2011 Nissan Xterra
- To add a 7-Way trailer connector and a brake controller you will need # ETBC7 and the brake controller itself. Since your 2011 Nissan Xterra did not come with a factory 7-Way, a brake controller will need to be hardwired in. The ETBC7 kit comes with everything you will need, minus the brake controller, to set the vehicle up properly.
Since at most you will have 4 brake assemblies you will use the 20 amp circuit breaker that is included with the ETBC7. The 30 amp one will not be used and the
view full answer... - Options to Install a Brake Controller and Trailer Hitch on a 2013 Infiniti JX35
- We can provide you with all of the parts that you will need to install a trailer hitch, 7-way trailer connector and a brake controller on your 2013 Infiniti JX35, however none of the items will work with pre-wired circuits or plug-in ports on your vehicle. I spoke with my contact at Tekonsha and they have not guarantee that the Plug-In Wiring Adapter, # 3050-P will work on your vehicle. I also spoke with my local Infiniti dealer and they told me that the JX35 does not come with a port under the
view full answer... - Trailer Brake Controller Wiring Harness for 2013 Nissan Pathfinder
- The Tekonsha Brake Controller Wiring Adapter, part # 3050-P is indeed compatible with your 2013 Nissan Pathfinder. The adapter is compatible with Tekonsha Brake Controllers like the Prodigy P2, part # 90885 or the P2, part # 90195.
The harness will plug into the connector located near the top of the emergency brake pedal. Look for a wiring harness with a white tag on it that that reads Trailer Brake Connection..
view full answer... - 2013 Pathfinder trailer wiring
- The trailer wiring harness that you ordered # 118263 is a replacement designed to fit a 2005 - 2012 Nissan Pathfinder, All Styles. but it is not currently listed as a fit for a 2013. However, on a 2012, if the vehicle did not come with the factory tow package, then relay6s are needed, # C57000, to make everything fully functional.
view full answer...
