Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Tekonsha PowerTrac Electronic Brake Controller - 1 to 2 Axles - Time Delayed
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury
Part Numbers: 39523, 3035-P
Retail:$78.50
Price:$74.94
Shipping Special
Trailer Brake Controller with Wiring Installation - 2000 Ford F-250 Super Duty - Video
Trailer Brake Controller Installation - 2003 Ford F250 - Video
Trailer Brake Controller Installation - 2003 Ford F250 - Video
Trailer Brake Controller Installation - 2002 Ford F350 - Video
Show all 12 videos
Trailer Brake Controller Installation - 2003 Ford F250 - Video
Trailer Brake Controller Installation - 2003 Ford F250 - Video
Trailer Brake Controller Installation - 2002 Ford F350 - Video
Show all 12 videos
Tekonsha PowerTrac Electronic Brake Controller - 1 to 2 Axles - Time Delayed
part number: 39523
Easy-to-use brake controller activates your trailer brakes electronically when you engage the brakes in your tow vehicle. Set braking intensity to your preference and towing application.
Features:
- Brake controller activates electric trailer brakes (sold separately)
- Signal is sent to trailer brakes when tow-vehicle brakes are activated
- Adjustable output control lets you determine the amount of braking force
- Set to maximum when you travel through hilly terrain with your fully loaded trailer
- Back off the power output when you tow a lightweight trailer
- LED indicator on front of unit
- Green light indicates that brakes are connected
- Color changes to orange and then to red as the power output increases
- Built-in manual override
- PowerTrac can be used with trailers that have up to 2 axles (4 brake assemblies total)
- Mounting bracket and hardware included
- No need to mount level
- Additional pigtail harness (sold separately) or plug-in, vehicle-specific brake-control adapter (sold separately) can be used for certain applications to further reduce installation time
Specs:
- Dimensions: 3" wide x 5" long x 1-1/4" tall
- Limited 5-year warranty
Unlike pendulum-style controllers, which react to the inertia that is created by your tow vehicle slowing down, the PowerTrac applies your trailer's brakes when the brake pedal in your tow vehicle is engaged. The trailer brakes will be activated with an intensity set by you. This output (amount of braking power) is adjustable to suit your preference, as well as road conditions, type of trailer and load. You can also apply the brakes manually with the integrated override.
Because inertia plays no role in the functioning of this controller, you do not have to mount the unit at any particular angle. As a result, mounting options are nearly limitless. After mounting the unit, hardwire the end of the included pigtail harness directly into your vehicle. For even easier installation, a vehicle-specific wiring adapter (sold separately) is available for certain vehicles. One end of the custom adapter plugs into your vehicle, and the other end plugs into your controller - no hardwiring required. To transfer the PowerTrac to another vehicle or to remove it for storage, just unplug the unit and remove it from the mount.
Note: For vehicles without brake-control wiring adapters, a 20-amp circuit breaker (9506P - sold separately) is required.
See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) that includes all the parts necessary to install the PowerTrac brake controller.
80500 Tekonsha PowerTrac Electric Brake Control
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ford, Lincoln, Mercury
part number: 3035-P
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.
Features:
- Wiring adapter eases installation of your electric brake controller
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
- Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
- Limited 1-year warranty
Installation of Tekonsha Brake Controller Adapter
For most applications, the factory plug is located beneath the dash, near the center console. If you have a Ford full-size van, the harness is underneath and to the left of the steering column. The Ford Explorer and Mercury Mountaineer have 6-pin connectors behind the glove box on the passenger's side. On a 2013 Ford Explorer, the connection point could be behind the driver's side kick panel.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
3035-P Tekonsha Brake Control Wiring Adapter with 2 Plugs
Video of Trailer Brake Controller with Wiring Installation - 2000 Ford F-250 Super Duty
Video Transcript for Trailer Brake Controller with Wiring Installation - 2000 Ford F-250 Super Duty
Today on this 2000 Ford F-250 Super Duty we are going to install part number 90885-3035P. The Tekonsha Prodigy P2 brake controller with the adapter cord that will plug into the factory Ford outlet. The first thing we need to do is get access to the port near the panel underneath the steering wheel that we have to temporarily remove. You can simply use a coin to undo the latches. Right here is the port that we need to plug into. That is kind of hard to get the wire harness in there and plug it in so you can use a screwdriver or a trim panel tool like we are using and just pop it up a little bit, get underneath of it and pop it loose so you can get a better angle at it. Take the cord and plug it in and take the cable and route it below and put the panel back into place. 00:55
We will mount the brake controller in this spot right here and it looks like it has had a brake controller in there once or twice before but we will use some fresh plastic because these holes are too big for the screws. Take a second and run the screws into the brake controller just to clean them out a little bit to make it a little easier to assemble. Plug the cord into the back of the brake controller and bolt the brake controller to the bracket. Now take a couple of seconds to zip tie and bundle up the wires. When we plug in the brake controller we notice that we did not have any power going to it, there is no lights that came on the brake controller display so we will take a look underneath the power distribution box and see if there is a blown fuse or a missing fuse. This is the spot that is normally for the brake controller accessory port and obviously it does not have a fuse so we will install a 30 amp fuse and check. Check out the brake controller, it looks like we have got two dots right here, that tells us that the brake controller is getting power and we are good to go. There you have it for part number 90885-3035P.
Ask the Experts about this Brake Controller
Do you have a question about this Brake Controller?
- Tekonsha Powertrac 2-4 Electric Brake Controller on a 2007 Chevy Tahoe
- Yes, your brake controller can be installed on your 2007 Chevy Tahoe. As long as the controller is functioning properly, it will wire the same as any other brake controller. There is no plug present under the dash, but the wires are already there. You only need to splice the brake control wires together with those already present under the dash. These wires are tied up with white tape to the left of the brake pedal. You need to connect 4 wires to the controller, as follows; red (12v power feed)
view full answer... - Availability of Brake Controller Harness for 2001 Toyota Tundra
- If you are looking for a brake controller harness, there are none available for the 2001 Toyota Tundra. The 2001 Tundra did not have factory tow packages as an option, so a brake controller will have to be hard wired into the vehicle.
You will need part # ETBC7 to create a 7 way plug at the rear of the truck. I will include a video on this kit. You will also need to install a 4 way connector. Toyota put the provision in for this so you will need part # 118378.
Once you have these parts in
view full answer... - Will a Brake Controller Draw Enough Power When Not in Use To Drain a Car Battery
- The brake controllers available now either are only on when they are activated, or a have a timed shut-off or idle state after a certain time period. Some of the older brake controllers never shut-off, but they did not drain battery power as the only component that would be on is a low amperage LED indicating that the controller has power or whether or not it was connected to a trailer.
As long as you have a healthy battery, you should not have a problem. Since your car is only 2 maybe 3 year
view full answer... - Adjusting Prodigy Brake Controller For Maximum Braking On a 1500 Pound Camper with a 1999 Ford F-150
- There are a number of factors to address if you feel that the trailer brakes on your camper are not performing to expectations. The first thing I would check is the mounting and leveling of the brake controller. The Prodigy must be mounted from 0 degrees to 70 degrees nose up but cannot be mounted canted to the right or left. Once mounted correctly the Prodigy, item # 90185, will acquire the level setting and you will need to adjust the power. If you have the power set to full and the trailer br
view full answer... - Trouble Shooting Tekonsha AccuTrac Brake Controller Not Recognizing Trailer on a 1999 Ford F-150
- I spoke with my co-worker, Bob, about this for some time this morning. We are both thinking you have a ground issue somewhere or possibly a short. Between the trailer brakes and the brake controller there are several grounds that need to be checked. I will start at the top and work down one by one till we can find the source of the problem. Some of this may be redundant so bear with me.
I assume you mean that the green light does not come on when the truck is on and the trailer is connected.
view full answer... - Brake Controller Not Functioning Properly On a 2004 Chevrolet Pickup When Brake Pedal is Pressed
- It sounds as if you may have the incorrect brake controller wiring harness. The correct wiring harness for the 2004 Silverado 2500 HD is the Universal Brake Control Wiring Adapter 2003 - 06 Chevrolet, GMC, Cadillac, item # 20264. Unplug the harness and check the wire locations in the connector.
When holding the connector with the locking tab in the down position the red wire should be in the bottom right position closest to the locking tab. If the red wire is in the top left position, farthes
view full answer... - Looking to Upgrade the Brake Controller On a 2004 Silverado 1500 for Towing a 2010 Outback Trailer
- The Prodigy P-3, item # 90195, is definitely an upgrade from the Hayes-Lemmerz Energize III Electric Trailer Brake Controller, item # 81741B. You would definitely see an improvement in the braking performance and a reduction in the delay you are experiencing with the Energizer controller.
The P-3 uses an accelerometer to detect how fast the vehicle is slowing and apply the correct amount of power, based on user settings, to the trailer brake magnets. This system is almost seamless with the ve
view full answer... - Can You Give Detailed Step By Step Instructions For Brake Controller Install On 2001 Toyota Tundra
- To install a brake controller on your vehicle you will need Brake Controller 7 & 4 Way Installation Kit, part # ETBC7 and the Tow Ready Custom Fit Vehicle Wiring, part # 118378 on your 2001 Toyota Tundra.
If your 2001 Toyota Tundra has an existing 4-way connector, you will not need to install part # 118378.
For installation of part # 118378, start by disconnecting the negative terminal on the battery and remove the battery hold down bracket and slide the battery towards the motor. Next,
view full answer... - How to Adjust the Power Trac Brake Controller on a 2004 Grand Cherokee Overland with AccuTrac
- It sounds as if you will need to adjust the power settings on your brake controller. There is only one adjustment on the Tekonsha Power Trac Brake Controller, item # 39523. It is the power gain setting and should be adjusted so the trailer brakes are close to but do not lock up, with each different load on the trailer.
The Power setting is turned up and down to increase or decrease the amount of power sent to the trailer brakes. If you have the power setting set too high on a time delayed con
view full answer... - Can the Tekonsha Powertrac Trailer Brake Controller # 39523 be Installed on a 2010 Toyota Tundra
- Yes, you can install the Tekonsha Powertrac, # 39523, in your 2010 Toyota Tundra. There are 2 ways you can wire in the brake controller. If the harness that came with the truck has blunt cut wires at the end that connects to a brake controller, you will need to match the wires on the brake controller to the functions on the harness as follows:
White on brake controller ground
Black on controller = 12 volt power
Blue on controller = out put to trailer brakes
Red on controller = in from sto
view full answer... - Troubleshooting a Tekonsha Powertrac Brake Controller # 39523
- There should not be 12 volts coming out of your ground terminal (7:00) on your vehicle connector. That sounds like where your problem is located. It sounds as if the 12 volt accessory that should be in the 2:00 position of your connector has been mistakenly wired to your ground circuit.
I attached a picture of how the connector on your tow vehicle should be wired by function for you to check out. I also attached an FAQ page on trailer wiring that you might find helpful.
view full answer... - Troubleshooting Fading Brake Output with Tekonsha Powertrac Trailer Brake Controller # 39523
- I spoke with my contact at Tekonsha about the Powertrac Brake Controller, # 39523. She stated that if the testing you are doing is with the vehicle and trailer parked, when you step on the brake or use the manual override, the output will go to the preset limit, but then, since the voltage is not needed, it will fade out. When moving the voltage will stay applied.
She also suggested testing the blue output wire using a test light like # 3808 while stepping on the brake. Having the testing lig
view full answer... - Using Wire for Bed Cap 3rd Brake Light Instead of Brake Stoplight Switch to Install Brake Controller
- As long as you have verified that the wire in question only goes hot when the brake pedal is applied, there is no reason why you cannot use the wire intended for the bed cap third brake light. If you do not have a circuit tester, we offer one, part # 3808.
Certain vehicles (like GM trucks produced in the late 1990s) had brake switch wiring that was very difficult to access. In those instances, we typically recommend doing exactly what you propose.
view full answer... - Finding Correct Brake Stoplight Switch Circuit to Install Brake Controller on 2004 Toyota Highlander
- I do not have any specific information about the color of the wire you are looking for, but I can describe how to find it.
Use a circuit tester like part # 40376, and probe each wire coming off of the brake stoplight switch. As you probe each wire, press the brake pedal. Once you find the circuit that only shows current when the brake pedal is pushed, tap the red controller wire into it.
view full answer... - Tekonsha Power Trac Brake Controller # 39523 No Longer Applying Brakes When Brake Pedal Pushed
- It sounds as if you might try to adjust the power settings on your brake controller. There is only one adjustment on the Tekonsha Power Trac Brake Controller, part # 39523. It is the power gain setting and should be adjusted so the trailer brakes are close to but do not lock up, with each different load on the trailer.
The Power setting is turned up and down to increase or decrease the amount of power sent to the trailer brakes. If you have the power setting set too low on a time delayed cont
view full answer... - Light Does Not Come On when Tekonsha Pod Trailer Brake Controller is Installed on a 2010 Ford F-150
- The first thing I reocmmend is to connect a trailer to the vehicle. The light will not come on if a trailer is not connected. If you do connect a trailer and the light does not come on it could indicate a few different issues.
First, check the black wire behind the controller for voltage. If there is no voltage going to the controller it will not turn on. You will need to check the fuses associated with the tow package to determine if something is blown or missing.
You may also have an op
view full answer... - Is a Brake Controller Plug and Play Wiring Harness Available for a 2003 Mercedes ML 350
- There is not an aftermarket plug and play brake controller wiring connector available for the 2003 Mercedes ML 350. You may be able to purchase one from the vehicle dealer though.
I spoke with my contact at Tekonsha and his advice is that you should take your Mercedes M Class vehicle to the dealer to have a brake controller installed. The Mercedes vehicles have very sensitive wiring and splicing into the brake circuit or power on the vehicle can cause issues.
If you have wiring experience
view full answer... - Brake Controller Power and 12 Volt Hot Lead Fuse Locations on a 2011 Chevy Tahoe
- Most vehicles are already equipped with the fuses mentioned in the video, which is what we have come across. If your vehicle does not have one or both fuses, you will need to insert your own fuses. To find the correct locations, you can look at the legend on the inside cover of the power distribution box.
Sometimes, the locations are the ones closest to the terminals. In this case they are slightly off to the right (driver side) as you can see in the video I have linked at about the 5:25 mar
view full answer... - Replacing the Manual Slide Knob on a Pod Brake Controller and Troubleshooting No Green Light
- I made you a short video that shows how to replace the knob provided that the little tabs on the back of the knob or where they mount are not damaged.
When you do not get a green light, that means that the trailer is not connected, there is a short to the brake output wire, or there is a bad ground connection. It could also mean that there is no power going to the controller black wire. Use a circuit tester like # 3808 if needed to determine if power is on the black wire.
Then, sever the
view full answer... - Will the Pod Trailer Brake Controller Fit a 2005 Dodge Ram 1500
- The Pod brake controller, # 39523, does come up for a 2005 Dodge Ram. Depending on how the truck is equipped, you will also need 1 of 2 harnesses. If the truck came with a factory 4 or 7-Way trailer connector, you will also need wiring harness # 3020-P. If the truck did not come with a trailer connector, you will need # 20127. I have included links to a couple of videos that should help.
view full answer... - Location of the Brake Controller Port for 2004 Ford Explorer with Tow Package
- On a 2004 Explorer with the newer body, the port is behind the glove box on the left side. You will open the glove box, push in the two tabs it rests on to get it to open further and the connector is buried on the left hand side, close to the center console.
The port is located above the pedals for F-150/Expedition or larger Ford Trucks and SUVs.
view full answer... - Location of Brake Controller Port on 2001 Ford Expedition
- The female port for this part should be located underneath the dash close to or behind the center console, it is gray in color. It should be very close to the OBDII diagnostic port, the large trapezoidal shape plug by the center console underneath the dash. I spoke with one of our installers and he said it should be within a 6 inch radius of that OBDII port.
We have a video on a 2007 Expedition, but you said you have searched our site so I assume you have seen it. I will include a link in ca
view full answer... - Brake Controller Wiring Harness For a 2009 Ford F-150 Pickup
- The Brake Control Wiring Adapter for Ford F-150 - 2 Plugs, item # 22292, is the wiring harness you will need for installation of a Tekonsha Prodigy P2- # 90885, Tekonsha P3 - # 90195 or a Draw-Tite Activator III - # 5520.
If you need a harness to wire a brake controller which is hard wired you will need the Brake Controller Wiring Adapter for Ford F-150, item # 20272.
The Tekonsha Wire Replacement for Ford Vehicles, item # 3035-P, is for older Ford models and will not work on the 2009 mode
view full answer... - Installing a Tekonsha P3 Brake Controller on a 2008 Ford F-450 with a Factory Brake Controller
- You should not have a problem installing the Tekonsha P3 Proportional Brake Controller with Ford Super Duty Adapter, item 90195-3034P, in your F-450 truck. This item number comes with the vehicle specific wiring connector for your truck. The biggest problem is that when removing your factory brake controller you will get a fault code on the dash that will not go away until you take the truck to the dealer and have the PCM (Power-Train Control Module) flashed so that the vehicle does not look for
view full answer... - Wiring Harness for Installation of the Voyager 9030 Brake Controller on a 2006 Ford F-150
- You will need the Universal Brake Control Wiring Adapter Ford, Land Rover, Lincoln, Mercury, item # 20260, to install the Tekonsha Voyager 9030 Brake Controller, item # 39510, on your 2006 Ford F-150. You will just have to splice the like colored wires from the Voyager to the harness with the included butt connectors.
I have linked instructions for the Voyager in case you would like to review them before setting the controller up on your new vehicle.
view full answer... - Hardwiring a Brake Controller from Scratch on a 2010 Ford Flex
- On the 2010 Ford Flex, you will have to hardwire a brake controller. There are 3 items you will need to complete installation. First is a brake controller, second is the Tow Ready Custom Fit Vehicle Wiring, # 118472, and third is the 7 and 4 Way Installation Kit, # ETBC7.
You will start by installing the Tow Ready Custom Fit Vehicle Wiring, # 118472. I have included a link to the installation details below. Installation is simple. The T-one harness plugs in line with your vehicles taillight w
view full answer... - Recommended Brake Controller for 1991 Ford F250
- Brake Controllers are not vehicle specific, you can use any controller you wish on your F250. This being said, I would recommend a proportional-type controller like the Tekonsha Prodigy, part # 90185. The Prodigy is our best selling brake controller, and is popular because it is easy to use and the initial set up is very simple.
A proportional controller is superior to the older technology used by the time-delayed brake controllers. The proportional controller uses an internal sensor that can
view full answer... - Where is the Brake Controller Port Located on a 2010 Land Rover Range Rover Sport
- You should find your brake controller port underneath the dash somewhere in the center, somewhere above the brake pedal. You would find the port in this location on all Land Rover vehicles equipped with a port. It should be a gray colored plug that will have 6 pins/holes. There should only be 4 or 5 wires.
view full answer... - Blown Stop and Turn Signal Fuses After Installation of Prodigy Brake Controller 2004 Ford F150
- It sounds to me as if you may have a wiring harness that is pinned out improperly causing the fuse to blow.
The first thing I would do is check the pin out diagram in the instructions (see link) and make sure your connector matches the diagram in the instructions. If it is improperly pinned you can change the pin out to the correct orientation using the instructions.
If the connector is pinned out properly there may be an issue with the brake controller or vehicle wiring.
Check out this
view full answer... - Where is the Brake Controller Port on a 2005 Ford E-350 Super Duty Diesel with Cut Away Box
- If your 2005 Ford E-350 has a factory 7-Way trailer connector, the brake controller harness, # 3035-P, is the correct harness for numerous Tekonsha and Draw-Tite brake controllers. The port will be tucked up under the dash, to the left of the steering column.
If your vehicle has a factory 4-Flat, you will need to add Adapter 4 Pole to 7 Pole and 4 Pole, # 37185, at the rear of the vehicle. The blue brake wire will need to be routed from the brake controller to the 37185 harness. The wires for
view full answer... - Can The Prodigy Brake Controller, # 90885, Be Installed In The Console On A 2009 Ford Flex
- Since your 2009 Ford Flex has the factory tow package and a factory 7-Way trailer connector at the rear of the vehicle the location of the brake controller plug is located under the dash, near the center console. There should be a open connector that will plug into the one end of the Tekonsha Wiring Adapter, # 3035-P, and the other end of the adapter will plug into the back of the brake controller.
The Prodigy Brake Controller, # 90885, can be mounted in a 360 degree vertical range. So the mo
view full answer... - Location of Brake Controller Port Underneath Dash Of 2001 Ford Expedition
- I spoke with one of our installers and he informed me that the factory port you are looking for will be towards the center of the dash on the driver side. It will be located within 6 to 12 inches of the OBD II port. If you have the bottom panel removed on the driver side of the dash and are looking in and up towards the center of the dash you should be able to see the plug. It won't be hanging down, and may be tucked away behind some other wires. The color of the port should be gray.
In addit
view full answer... - What Are the Correct Brake Controller Wiring Harness Adapters for a 2005 Ford F-350 Super Duty
- For a 2005 Ford F-350 Power Stroke, the correct brake controller wiring harness adapter for Tekonsha brake controllers is the Tekonsha Wire Replacement, # 3065-P.
For Draw-Tite brake controllers, you would use # 20267. And for Hopkins you would need # HM47735.
On the 2005 Ford F-350 Super Duty, the available brake controllers come with the specific wiring harness required to connect it to the port on the truck in the storage pocket, just above the ashtray and toward the center of the dashb
view full answer... - What Brake Controller Wiring Harness Is Needed For A 2005 Ford F350
- For your 2005 Ford F350 that has the factory installed brake controller port you will need the Tekonsha Wire Replacement for 2005-07 Ford Super Duty, # 3065-P. This will have a plug on one end that will plug into the factory brake controller port and the other end will plug into a Tekonsha brake controller.
The Tekonsha Wiring Harness, # 3035-P, will not fit on your 2005 Ford F350.
If you need a brake controller I would recommend the Tekonsha Prodigy P2 Brake Controller, # 90885. The Prod
view full answer... - What Is Needed To Add A Brake Controller To A 2003 Ford F-150 With Factory Tow Package
- The parts you will need to add a Tekonsha brake controller to your 2003 Ford F150 with factory tow package will depend on the trailer connector you have on your vehicle.
If you have a factory 7-way connector on your vehicle, you will need the brake controller and the Tekonsha Wire Replacement Harness, # 3035-P. The # 3035-P will plug into your brake controller and the other end will plug into the factory brake controller port, which will be located under the dash near the center console on yo
view full answer... - Installing a Trailer Brake Controller on a 2011 Ford Escape with Factory Tow Package
- I spoke with my contact at Tekonsha about a brake controller wiring adapter for a 2011 Ford Escape with the Trailer Tow Package. He did not have specific information regarding the 2011 models, but historically the Ford Escape has been a hardwire only model. This means that you would first need a 4-Way wiring harness.
With the factory tow package, you would use the Draw-Tite Custom Fit Vehicle Wiring, # 118251. Without a tow package, you would use the Tow Ready Custom Fit Vehicle Wiring, # 11
view full answer... - Brake Controller Wiring Adapter for 2010 Ford F150
- The Brake Controller Wiring Adapter, part # 22292 does carry over from the 2009 to the 2010 Ford F150 and is the correct wiring adapter for installing a Tekonsha P3 in your 2010 Ford F150.
I will link you to the install instructions for the wiring adapter, as well as a link to an installation video that you might find helpful. The video shows a controller being installed on a 2009 F150, but the procedure on your 2010 model would be similar.
view full answer... - Which Wiring Harness Adapter Do I Need to Install A Prodigy Brake Controller on 2011 Ford F-450
- The wiring adapter that you will need for your 2011 Ford F-450 is the Tekonsha Wire Replacement for Ford Super Duty Pickups, part # 3034-P.
For a brake controller, I would recommend the # 90195-3034P kit, which includes the wiring adapter and the brake controller unit. The Prodigy P3 can be used with electric trailer brakes and/or electric over hydraulic brakes. The P3 also has an LED display with 9 different color options and features diagnostic troubleshooting displays. I recommend the P3
view full answer... - What Is Needed to Install a Tekonsha P2 Electric Trailer Brake Controller on a 2010 Ford F-150
- The only parts you will need to install the Tekonsha P2 brake controller on your 2010 Ford F-150 with tow package are the brake controller itself and the correct wiring adapter. We sell these parts together as # 90885-22292. I have included the brake controller instructions and the wiring adapter instructions below. I have also included a video showing the harness being installed on a 2009 model which will be very similar to your 2010. The port to plug in the harness could also be up under the d
view full answer... - Installing Trailer Brake Controller on a 2006 Ford F-150 with Factory Installed Brake Controller
- According to our FAQ, which I have linked for reference, you only need to unplug the one connector that will be used with the Prodigy P2, # 90885. The plug that is needed will have matching wires with the brake controller adapter harness. The wiring should be labeled for function.
view full answer...
