Contact and Help



What our customers are saying:

Ordered on 4/13/04 and received on 4/15/04...two days...no bad!

Dave

Knightstown, IN

Fulton Trailer Jacks Fulton Trailer Couplers Fulton Trailer Accessories

Fulton





Fulton Reviews and Installation Videos



See all Fulton videos
Expert Answers about Fulton

  • How to Choose the Correct Size Trailer Winch For a Boat Trailer
  • The size winch that you will need depends on a couple of different factors. I have included part of our hand winch FAQ below regarding boat winches and have linked the FAQ article for you to view. Finding the Right Capacity Winch for your Boat Trailer Boat-size-to-winch capacity is generally 2 to 1 With good rollers and short winching distances, increase the ratio to 3 to 1 With wooden bunks and long winching distances, reduce the ratio to 1 to 1 For example, a 2,200-lb boat...
    view full answer...

  • Trailer Dolly Recommendation for Moving a Boat Trailer in and out of a Garage
  • The Fulton F2 Swing-Up Trailer Jack # F1413020134 that you referenced would certainly be capable of moving your trailer around as long as the tongue weight of your trailer does not exceed the 1,600 lb capacity of the jack. However, it would not be nearly as easy as using a Trailer Valet Swivel Jack and Trailer Mover # STC-V211. I believe I have something that would be ideal for you. Since you are looking for an easy way to move your trailer in and out of your garage I think you might...
    view full answer...

  • How to Replace the Strap on the Fulton Trailer Winch # FT2605Z0301
  • Look for the bolt on in the drum on your Fulton Winch, # FT2605Z0301, that is closest to the center of the drum. The bolt and nut that came with the winch use this hole. You will want to have the strap with the sewed side down. Run the bolt through the first hole, only slightly, then through the loop in the strap, and then out the other side of the drum. Secure the nut only tight enough to eliminate the side to side play of the bolt. Over tightening it can damage the drum. All you...
    view full answer...

  • Wheel Bearing Replacement For Snow Bear Trailer
  • I spoke with Snow Bear and they said they no longer support the utility trailers, so information about your trailer is not available. The best way to find the correct bearings is to get the numbers off of the old bearings. Another method is to take measurements of the spindles, using a precision digital caliper. I have attached a drawing that shows where the measurements need to be taken. If you can get the original part numbers, it would be much more reliable. The drawing shows where...
    view full answer...

  • Will the Replacement F2 Swivel Jack fit a Mastercraft Boat Trailer with Weld On Swing Up Jack Plate
  • To determine if the Fulton F2 Swing-Up Trailer Jack with Dual 7 inch Wheels, Sidewind -1,600 lbs - No Mounting Hardware, item # F1413100334, will bolt directly to the old bolt through mount, without cutting it off, you will need to measure the bolt pattern on your trailer. I went out to the warehouse and measured the bolt mounting pattern on the Fulton F2 Swing-Up Trailer Jack, item # F1413100334, and the bolt holes are 3-3/8 inches on center by 4-3/8 inches on center. If you determine...
    view full answer...

  • How to Mount a Fulton Plastic Fender # F008553 To a Trailer To Support Weight of Stepping On It
  • The Fulton Plastic Fender with Top Step, part # F008553, does not come with mounting hardware. Fulton does not provide mounting bracket kits for the fenders. You can use your fenders original mounting brackets or use the Redline Galvanized Steel, L-Shaped, Bolt-On Brackets, part # PF775-BKT-2. See picture to the right that will show the underside of the fender with the brackets to give an idea of how to mount it to your trailer. I would recommend to install the fender with L-shaped...
    view full answer...

  • Replacement Fulton Jack for a Ranger Boat Trailer
  • It is possible that Fulton jack # FTJ120W0301 is the same jack that is used on your Ranger boat trailer. If your current jack is a side wind swivel jack with 10 inches of lift and rated for 1,200 pounds AND it mounts to a bracket welded to the trailer frame and held to it with a snap ring, then yes, this is the correct jack. I have linked a video review of this jack for you. I have also included a link to all of the Fulton side winding swivel jacks for you.
    view full answer...

  • Should I Use a Bolt On or a Weld on Fold Away Coupler On a Shorelander Trailer with 3x3 Frame
  • I more or less agree with you. The Fulton Fold-Away Hinge Kit for 3 x 3 inch Trailer Tongue - Weld-On, item # FHDPW330300, is a cleaner look and if you got a bad weld job you would not have a safe setup. I have done some welding, I am in no way a professional weldor, and in my limited experience a good weld will not fail before the steel it is welded to will fail. If you like the clean look of the weld on I would have a certified weldor perform the operation. If you take the trailer to...
    view full answer...

  • Recommended Hand Winch to Pull Up a 3,500 Pound Vehicle onto a Tow Dolly
  • There are a few options I recommend when using a winch to pull a 3,500 pound car onto a tow dolly. The Fulton single speed hand winch # FT18010301 has a 1,800 pound capacity. A winch can pull a rolling load that exceeds its rated capacity, but an incline, like the ramps on your tow dolly, adds some resistance. To find the amount of load that can be pulled up an incline, multiply the winch capacity by the factor shown in the chart (see the help article on hand winches I included). For...
    view full answer...

  • Recommendation for a Spare Trailer Tire Mount for a 6 Lug Trailer Wheel and Tire
  • We have three different spare tire carriers that will accommodate 6 lug wheels. The first is the Fulton High Mount spare tire carrier, FHDSTC0101. It fits wheels up to 16-1/2 inches in diameter. It is for 3 inch by 5 inch trailer tongues and has a 4-3/4 inch lift. The second is a Bumper Mount Spare Tire Carrier, # TR-1. This is designed for 4 inch box bumpers and is 18 inches high. Finally, we have a spare tire carrier for horse and livestock trailers, # 413200. This is a weld on...
    view full answer...

  • Best Swivel Trailer Jack for Salt Water Environment for a Boat Trailer
  • The problem that some people have with the Fulton F2 jacks such as # F1413040134 is that they are not used to seeing plastic pieces on a trailer jack. If you are rough with a piece of plastic, it can break. But at the same time plastic is not going to corrode. If the jack is abused a person could have trouble with it. The metal parts of the jack are aluminum which is naturally corrosion resistant. Other jacks are going to be made of steel and zinc-plated or coated. Steel can rust, even...
    view full answer...

  • Replacement Fender for Shorelander Boat Trailer SRV1724
  • Thanks for the information regarding your boat trailer, I was able to look up the tire size of your trailer in order to determine an appropriate replacement fender. I found that the trailer tire specified for your trailer was listed as a ST185/80R13. Therefore the trailer wheel is a 13 inch wheel with an approximate overall diameter of 24.4 inches. If your trailer tire is not this size please feel free to reply with an updated tire size and I can make additional recommendations for you....
    view full answer...

  • Trailer Frame Fit and Retracted Heights For Fulton F2 and Fulton XLT Trailer Jacks
  • I spoke with my contact at Fulton and he confirmed that both the Fulton XLT # F141133 and the F2 Swing-Up # F1413040134 will fit your trailer frame that measures 3 inches x 1-1/2 inches. Typically bracket height is measured from the bottom of the wheel to the center of the bracket. I was able to determine the height from the bottom of the wheel to the bottom of the bracket using the bracket dimensions. For the XLT # F141133, to the center of the bracket measures 15 inches when retracted....
    view full answer...

  • Corrosion Resistant Trailer Jack for a Trailer with 2 Inch by 4 Inch Frame
  • I think the best choice is going to be a bolt-on Dutton-Lainson jack with a Zinc plated yellow chromate TUFFPLATE finish. If your trailer has a channel tongue, jack # DL22300 fits up to a 3 x 5 inch frame. If you have a square tongue use # DL22800. The finish on these jacks is very corrosion resistant. An aluminum jack that will fit your frame size is not available.
    view full answer...

  • Determining Which Trailer Fender Size is Needed
  • Trailer fenders are classified by the diameter of the trailer wheels they're compatible with. For instance, the # F008583 fender you referenced works with 13 inch diameter wheels. If you're unsure of the diameter of your wheels, the last two digits of your tires size will indicate the diameter of the wheel. For example, if your tire size is 185/80-13, 13 represents the diameter of the wheel. Choosing a fender appropriate for the wheel diameter is the most important factor. I've linked...
    view full answer...

  • How to Install the Spring in the Ratchet Repair Kit for Fulton Winch, # 1562S00-SP
  • I went out to the warehouse and pulled one of the winches the Ratchet Repair Kit for Fulton Winch, # 1562S00-SP, and took it apart. I got to use tools so I was happy to do so. The spring is the trickiest part of this particular assembly because if it is not in the right place, the winch will not ratchet correctly (as I found out). The whole assembly will need to be loose to position the spring. But as far as placement, on the inside of the winch, one end of the spring goes through the small...
    view full answer...

  • Will Fulton Plastic Trailer Fenders # F008575-2 Fit an 18 Foot Boat Trailer with 15 Inch Wheels
  • Based on the measurements you have provided it sounds as if the Fulton plastic fenders, # F008575-2, are slightly larger than your existing fenders. Larger is fine, but if they were too small that is when you run into problems. Given that you have 15 inch wheels these fenders should fit well because they are designed for 15 inch wheels. The only thing that you may have to move or modify would be the existing mounting brackets on the trailer. This is because there is not standard measurement...
    view full answer...

  • What are the Dimensions of Fulton Plastic Trailer Fender # F008584 and # F008585
  • I would be happy to provide the dimensions for the Fulton Plastic Fender, # F008584 and # F008585. I have actually made a picture showing the dimensions for you.
    view full answer...

  • Is Mounting Hardware and Brackets Available for Fulton Trailer Fenders
  • To replace the fenders on your trailer with the Fulton black trailer fenders, # F008585-2, you will need to either reuse the old hardware or you will have to fabricate some hardware. If the old hardware cannot be used, a visit to a hardware store will provide you with the parts to fabricate something that will work.
    view full answer...

  • Bolt On Swivel Trailer Jack Recommendation for a 6,000 lb 27 foot Boat Trailer
  • To determine the correct jack capacity for your boat trailer, you will need to know the tongue weight of the trailer. Once the tongue weight is known you can select a jack with a lift capacity that is equal to or greater than the tongue weight of your trailer. Typically tongue weights on boat trailers do not exceed 15 percent of the gross trailer weight capacity. Using this figure your tongue weight most likely will not exceed 1,000 lbs, (slightly more than 15 percent of 6,000 lbs) so...
    view full answer...

  • Are Mounting Brackets Included With Fulton Single Axle Trailer Fenders with Top and Side Steps
  • The Fulton Single Axle Trailer Fenders with Top and Side Steps , part # F008575-2, do not come with mounting hardware. Fulton does not provide mounting bracket kits for their fenders. You can use the original fender mounting brackets or use L brackets to mount the fender to your trailer frame. I have attached a link to the brackets we offer that you can choose from.
    view full answer...

  • Winch Needed to Secure Boat Dock When Water Level Changes
  • The weight capacity of the winch you need is pretty much going to dictate the cable size that is used on the winch you select. If you are using the winch to secure a 2 slip boat dock on a lake or river and need to extend and retract the cable due to water level changes, the closest thing we have at this time is the Fulton High-Performance 2-Speed Trailer Winch, # FT37000301. This winch will accept up to 185 feet of 7/32 inch cable. If 70 feet of 5/16 inch cable would work for you,...
    view full answer...

  • Instructions Needed for Bevel Gear Replacement in the Fulton Bolt-Thru Swivel Marine Jack # FXPD15L
  • We carry a replacement gears for the Fulton Bolt-Thru Swivel Marine Jack, item # FXPD15L. For the gears, you will need the Fulton Bevel Gear Kit, # F0933306S00. Installing the gears is fairly easy, You will need to remove the cap at the top of the jack. The handle and gear are held in place with a roll pin that will need to be removed. You can then remove the handle, square block and gear. You can then remove the bottom gear by lifting it out. If the bottom roll pin is damaged remove...
    view full answer...

  • Recommendation for a Hand Winch to Lift For Deer Feeder Poles To Raise 320 Pounds
  • I spoke with another member of our content team who uses a similar winch for deer feeder poles. He informed me that the item you selected, Fulton Single Speed Winch - 8 Long Handle - 1,300 lbs, part # FT13000301, will work fine. Another winch that will work for your application is Dutton-Lainson Hand Winch with TUFFPLATE Finish, Single Speed - 900 lbs, part # DL15002. When using either winch, for safety, you will want to make sure that nobody is standing under the barrels when they...
    view full answer...

  • Trailer Jack Repair or Replacement Parts
  • The nut you are seeing in the inner pipe is not designed to be replaced. It sounds as if your jack was wound past is working limit and either broke or ruined the threads on the lift rod. You will need to replace the jack, if this is the case. The parts you referred to, # F0933306S00, are located in the top of the jack and can be replaced. If you open the top of the jack and find these parts damaged, send me the make-model number of your jack and I will be glad to help determine the correct...
    view full answer...

  • Determining Which Replacement Wheel Bearings Needed for SnowBear 8000 Utility Trailer
  • To find the correct replacement bearings, you will need to pull one of the hubs off and remove the inner and outer bearing to obtain the reference numbers from them. The reference number will be stamped into the steel cage holding the bearings, as seen in the provided photo. Your grease seal will also have a reference number, as shown. If the numbers are unreadable, you can use an accurate measuring tool like a # PTW80157 digital caliper and measure the surfaces of the spindle where...
    view full answer...

  • Black Plastic Fender Recommendation for a Harbor Freight Trailer
  • You have 12 inch rims, but extra 3/4 of an inch you measured is for the lip of the tire that does not count towards the overall diameter. The black fenders part # F008559 should work well for you, but to utilize your current mounting setup you would need to trim these fenders near the underside so that you could attach them to your mounting brackets. You would also need to drill through the top of the fenders too.
    view full answer...

  • Reversing Handle to Other Side of Hand Winch
  • The Fulton winch you referred to, part # FT11000301 would not be easily modified to relocate the handle to the other side, as there is no hole to secure the pawl tension spring. The folks at Dutton-Lainson have told us that their 1600 lb capacity single speed winch, part # DL14527 is capable of being modified. The drum, its shaft, the gear shaft and pawl shaft would all need to be removed, and reversed. The gear shaft is held in place by both a nut and an e-clip that would need to be...
    view full answer...

  • Where to Attach the Safety Chains After Installing the Fulton Fold-Away Coupler Hinge Kit
  • You will need to locate the safety chains before the cut that is made to install the Fold-Away Coupler Hinge, # FHDPB330301, to be in compliance with DOT regulations. Normally the chains are welded to the bottom or side of the trailer framing, and ran forward. I would have a qualified weldor, weld a Safety Chain Loop, # E950, to the bottom of the trailer frame, before the fold way cut, and then attach safety chains, like part # 2118-348-04, with Safety Chain Quick Links, # 2114-553-04....
    view full answer...

  • Will the Fulton Trailer Fender # F008554 Work on a Master Tow Dolly Model 80THD
  • I checked out the master tow dolly 80THD online and it looks like the Fulton Plastic Fender, item # F008554, will mount to the brackets on the tow dolly, as long as the wheels on the tow dolly are no larger than 14 inches. The original equipment size for the master tow 80THD is 14 inches. Some modification of the brackets for mounting the fenders may be required, and the 80THD has lights mounted to the fenders, which will need to be transferred to the new fenders. Modification for attachment...
    view full answer...





^
About Us
photos and videos
1,056,204

Original Photos & Videos

Produced to make sure you know what you are getting and you get exactly what you need.

installations
35,570

Installations Completed

To make sure products work and fit the way they are supposed to.

etrailer call center
2,476,511

Phone Calls & Emails Answered

1,125,924 phone calls and 1,350,587 emails to help find the right solution.

etrailer training
400+

Average Hours of Product Training

We get to know our products firsthand so experts can better help you.

etrailer service
71

Years of Quality Customer Service

Assisting our neighbors and customers, face to face at the counter.

etrailer experts
193,357

Pages of Expert Information

Created to make sure you have all the answers to your questions, from real experts.