Expert Answers about Carr
Installation Instructions For Carr Tube Step # CARR104504 on a 2005 Dodge Sprinter Van- The installation of the Carr Tube Step # CARR104504 will require drilling on your 2005 Dodge Sprinter. The hardware used to attach the steps are standard hex bolts.
The attached directions give you a step by step, detailed installation procedure to follow.
The hardware you will need is included in this kit, however, depending upon your installation, you may not use all of the hardware that is included. The tools you will need are minimal - a Philips screwdriver, 1/2 inch open or box wrench
view full answer...
- Is the Gutterless Mount Kit Required to Install the Carr M-Profile Light Bar on a 2009 Ford F-150
- You will need to order the Gutterless Mount Kit, # CARR220062, to install the Carr M-Profile Light Bar, # CARR210701, on your 2009 Ford F-150 Lariat. Your truck does not have rain gutters on the sides of the doors or roof for the light bar to mount to.
To install the Gutterless Mount Kit, you will place the bracket under the topside of the door jamb. You can choose the location you like best to mount the brackets. If the weather seal is in the way, it can be pulled back and the bracket can b
view full answer...
- Will the Carr Hoop II Steps fit a 2013 Wrangler Unlimited
- Yes, I spoke with my contact at CARR and she confirmed that the Carr Custom-Fit Side Steps # CARR101241 that you referenced will work on your 2013 Jeep Wrangler Unlimited.
view full answer...
- Will Gutterless Mount Kit for Carr Light Bars, Part # CARR221502, Fit 1996 Dodge Ram Pickup
- The Carr Gutter-less Mount Kit for Light Bars, Part # CARR221502, is intended to allow mounting of various Carr light bars on vehicles that do not have rain gutters.
Rain gutters are u-shaped channels above the doors that direct rain water to the front and rear of the vehicle. This kit is a correct fit for your 1996 Dodge Ram Pickup so long as you do not have rain gutters. You can tell if you have them by running your finger from the vehicle roof down across the top of the door; if there is
view full answer...
- Step Bars for 2012 Jeep Wrangler Unlimited that are Lower than OEM Step Bars
- According to the folks at Carr, the OEM step bars you currently have would most likely interfere with the Carr steps. I am unaware of any longer brackets that would lower your bars, I would recommend you check with your Jeep dealer.
Your best bet would be to remove your existing steps and install the a set of # CARR101241 hoops. According to Carr, the step portion of the hoops would sit about 5-1/2 inches below the rocker panels. The steps are sold in sets of 2, for all four doors you would n
view full answer...
- Will Carr Custom-Fit 17-Inch Side Step, part # CARR124874-1, Fit a 1990 Toyota 4Runner V6
- Your 1990 Toyota 4Runner can be fitted with a number of different side step products, but not this particular one. I have included a link to our product page for all suitable steps for your 1990 4Runner. You have several options for sizes, materials and colors.
If you are interested in a 17-inch aluminum step (like the part # CARR124874-1 you were looking at) you can instead consider part # CARR124034. This part is a pair of two silver-finish cast aluminum alloy steps that comes complete with
view full answer...
- Is Drilling Required to Install Carr Hoop II Side Steps # CARR104501 on 2012 Toyota Tundra
- The Carr Hoop II Side Steps you referenced attach to the vehicle via holes that will need to be drilled in the back side of the rocker panel under the driver and passenger side door.
I have confirmed that this step is indeed a fit for your 2012 Tundra.
To see the installation instructions, click the provided link.
view full answer...
- Is There Drilling Required to Install the Carr Custom-Fit Side Steps
- Yes, to install the Carr Custom-Fit Side Steps # CARR125772 you will need to a little bit of drilling.
Check out the installation instructions for this product that I attached.
view full answer...
- Dimensions of the Carr Hitch Mounted Step # CARR180012
- The step dimensions of the Carr Hitch Mounted Step, # CARR180012, are 5 inches long by 2-1/2 deep. I have attached a photo for you to check out.
We also offer the CIPA Hitch Mounted Step, # 60050, which is slightly larger at 5-7/8 inches long by 2-5/8 inches deep.
If you wanted a significantly larger hitch step, then I would recommend the Bully Hitch Mounted Step, # CR-600, that has a 9 inch wide step pad that is 2-5/8 inches deep.
I have attached product links to each of these hitch
view full answer...
- Selecting Carr Gutterless Light Bars for 2009 Toyota FJ Cruiser
- There are two general types of light bars to consider, fixed and rotating. Rotating bars allow the bar and attached lights to rotate down out of the way when not in use. Both types can accept up to 4 lights.
Since the vehicle is predominantly black in color, and has black roof rails, I will suggest you consider options with black powder-coat finish as these may offer the best cosmetic match.
For the fixed-type bar, I suggest the Carr M-Profile Light Bar - Black Powder Coated Steel
Gutterl
view full answer...
- Will Carr Deluxe Light Bar Fit on 2009 Jeep Commander and Is Drilling Required
- The Carr Deluxe Light Bar # CARR210341 is a custom fit for your 2009 Jeep Commander and will provide an attachment point for 4 off-road lights. I have provided a link to the instructions for the proper installation of this product.
You will also need the Carr Gutterless Mount Kit # CARR220052 to install your light bar. It is designed for applications without external rain gutters. You will be required to drill 4 1/8 inch holes per bracket. I have included a link providing installation instruc
view full answer...
- Will the Carr Super Hoop Side Steps Fit on a 2012 Jeep Rubicon with Factory Installed Rock Rails
- I spoke with my contact at Carr and she told me that the Carr Custom-Fit Super Hoop Side Steps, # CARR121241, will fit on your 2012 Jeep Rubicon with the Rock Rails, but the Rock Rails will have to be removed to install the Super Hoop side steps. Once you have the Super Hoops installed, the Rock Rails can be re-installed in their original location.
view full answer...
- Installing Carr Super Hoop Side Step # CARR121241 on 2009 Jeep Rubicon
- The mounting brackets for the Carr Super Hoop Side Steps would mount directly behind the pinch weld or downward pointing lip that runs along side the underside of the vehicle below the doors. For each step, two holes would be drilled through the pinch weld, and two smaller holes drilled into the underside of the vehicle for the sheet metal screws. Carr recommends centering the step on the front edge of the drivers seat.
I have edited a diagram for you that will hopefully make things clearer f
view full answer...
- Are Carr Custom-Fit Side Steps Difficult to Install on a 2011 Jeep Rubicon
- The Carr Custom-Fit Side Steps, part # CARR121241, will fit your 2011 Jeep Rubicon. Installation requires a drill, a center punch, 5/16 inch and 1/8 inch drill bits, a pair of both 1/2 inch and 7/16 inch wrenches, a Phillips screwdriver and a pencil.
The assembly process consists of first attaching the mounting brackets to the cast aluminum steps using the supplied hardware (please note that not all hardware supplied will necessarily be needed for any given installation).
After you have de
view full answer...
- Which Truck Bed Step for a 2012 Ford F-250/350 Super Duty
- Since you are specifically looking to improve access to the tool box in your truck bed, we can recommend several better options. The item you referenced, part # CARR125001, is a cab step, and this might not provide you with the better access to your tool box that you want. It sounds like you would be better served by a bed step, two of which are listed below.
The Bestop Trekstep # B7540315 is spring-loaded and offers extruded aluminum construction with black powder-coat finish and a 400 pound
view full answer...
- Will a 40 Inch LED Light Bar Mount on the Carr XRS Rota Light Bar on a 2011 Jeep Wrangler
- You should be able to mount a 40 inch LED light bar on the Carr XRS Rota Light Bar, # CARR210221. The crossbar for this light bar is 53 inches long which should leave plenty of room for a 40 inch LED light. The top of the light bar has 1/2 inch bolt holes and elongated bolt holes giving you several options for mounting your LED light. I have attached the installation instructions for you to check out.
At this time we do not have a bumper mount or front mount light bar for your 2011 Jeep Wran
view full answer...
- How do the Carr Super Hoop Steps Mount to a 2012 Chevy Silverado 2500HD
- Those other stores are not entirely correct. You will need to drill into the metal of the truck and the steps are held on with nuts and bolts. I have linked the instructions for you to view. page 3, step 12 states to use the 5/16 x 1-3/4 hex bolts and nuts in the drilled holds to mount the brackets to the truck. There are sheet metal screws used in the installation, not self-tapping because drilling is required, but they are not the primary fastener used to hold the steps on the truck.
view full answer...
- Why are there Different Mounting Positions for Carr Custom-Fit Side Steps - Super Hoops
- The Carr Tube Steps, # CARR124991, have different mounting capabilities for the different vehicles they fit. These steps fit a 1998 to 2012 Ford Ranger 2-door or a 1998 to 2009 Mazda B-Series truck. Other vehicles that use the same or similar mounts may need to more horizontal or vertical depending on where they can fit on the truck body. I have included a link to the installation instructions for you.
view full answer...
- Do the Carr Custom-Fit Side Steps Require Drilling for Installation on a 2009 Jeep Wrangler
- The Carr Customer-Fit Side Steps, # CARR101241, mount by bolting steel brackets to the body of your 2009 Jeep Wrangler at each door. Drilling is required for installation. You will need a 1/8 inch and a 5/16 inch drill bit. I have attached the installation instructions for you to check out.
view full answer...
- Roof Rack and Side Step Recommendations for a 1998 Toyota 4Runner
- For side steps, we have several options for a 1998 Toyota 4Runner. I have included a link to the available options for you. For silver steps, we have # CARR103994 and # CARR124034 that you have referenced. I have included links to the installation instructions for each set for you.
For a roof rack, there are 3 different roof options that were available on the1998 Toyota 4Runner. You could have factory tracks that run front to back, a plain roof with no rails, crossbars, or tracks, or a factor
view full answer...
