Alfred Hitch Cover

Expert Answers about Alfred Hitch Cover

• Is Pin and Clip or Hitch Lock Required to Hold Hitch Cover In Place
• The Cubs Tail Gater Receiver Cover, part # AH-40314 will require either a pin and clip, part # PC3, or a hitch lock, such as part # 40107. The pin and clip or hitch lock are not involved with the electrical system, they hold the hitch cover or other accessory in place.
  view full answer...


• How Does the Colorado Buffaloes 2 inch Trailer Hitch Cover Install into a Hitch
• You are correct, the metal rods will go into the hitch opening and a hitch pin will slide through it to secure it. Check out the link I attached to another question I answered on a similar hitch cover that shows you exactly how it installs. You might also be interested in purchasing a Trailer Hitch Receiver Lock # 7683 to secure the hitch cover to your hitch. I attached a link to a review video for this product for you to check out also.
  view full answer...


• How is the Boise State Hitch Cover Held in the Receiver
• The Boise State Hitch Cover you mentioned, part # 03409210172 is retained in the receiver by means of a heavy wire hoop at the rear of the cover. The hitch pin or lock holds the cover in place. If you refer to the photo I produced, you can see a view of the back of the hitch cover.
  view full answer...


• How to Use the Bottle Opener on Tailgater Hitch Cover # AH-41102
• Although it is not as easy to use as some traditional bottle openers, Tommy did test out a tailgater hitch cover with the same bottle opener as the # AH-41102 and was able to get it to work. It took a little additional muscle and getting the bottle to exactly the right angle to get the opener to catch the cap properly. At first it seems a bit too small for the cap, but the entire cap should not really be inserted in the opening. Basically, you press the top of the bottle cap against the ton
  view full answer...


• Will the One Nation Under God Rattle in a Hitch
• This One Nation Under God 2 inch Trailer Hitch Cover # AH-10256 should not rattle much at all in the hitch of your vehicle. I have used hitch covers that use the same wire setup as this and they install very snugly leaving very little room for vibration. As long as you use a hitch pin and install this product correctly you should have no problem using this product while driving on back roads. For a little added security you might be interested in a locking hitch pin like our Trailer Hitch
  view full answer...


• Is a Locking Pin Required on the Alfred Hitch Cover # 034092100232
• The Alfred Hitch Cover, part # 034092100232, does not require a locking pin, but you can use one to prevent theft of the hitch cover. The hitch cover can be installed and held in place with your existing hitch pin and clip or you can use the Hidden Hitch Pin and Clip, part # PC3. If you want to lock the hitch cover to your hitch you can use the Deadbolt Hitch Lock, part # 7683. I am including a link to a video that will show how the Alfred hitch cover will attach to your hitch.
  view full answer...


• Which Style of Hitch Lock will Work to Secure the U.S. Navy Hitch Cover in a 2 Inch Hitch
• The C.T. Johnson DeadBolt Trailer Hitch Lock, # 7683, for 2 inch hitches, would be an excellent choice for securing the U.S. Navy Tailgater 2 inch Trailer Hitch Cover, # AH-41072. If you wanted a heavier duty stainless steel model, the Stainless Steel version, # 40107, would be a good choice also. Finally, if you have a newer Chevrolet or Toyota truck that requires a longer hitch pin, the DeadBolt Extra Long Trailer Hitch Receiver Lock, # RH5-XL, would be the correct choice.
  view full answer...


• Which Way Does the Pink Ribbon Trailer Hitch Receiver Cover, # 03409210234 When Installed
• Once installed into the receiver, the Pink Ribbon Trailer Hitch Receiver Cover, # 03409210234, will be oriented just like it is in the picture on the product page. The loop of the ribbon will be pointed towards the upper right corner (passenger side) of the vehicle.
  view full answer...


• How Does the One Nation Under God Hitch Cover Install Onto a Hitch
• The One Nation Under God 2 inch Trailer Hitch Cover # AH-10256 uses bent metal rods that will go into the hitch opening and allow for a hitch pin or lock to pass through and secure the cover to the hitch. I attached a couple pictures of the back of this product for you to check out as well as a video I put together that shows how the hitch cover will install onto a hitch opening. You may be interested in purchasing a Trailer Hitch Receiver Lock # 7683 as a theft deterrent also. I attached
  view full answer...


• What Size Hitch Cover Will Fit a 2009 Jeep Wrangler Unlimited.
• The hitch receiver size on a 2009 Jeep Wrangler Unlimited can be either a 1-1/4 inches or 2 inches. You will want to measure the inside diameter of the hitch opening on your Jeep to determine what size hitch you have. I am including a picture of the two different sizes of hitch receivers with the measurements. Also, I am including a link to a FAQ page on hitch receiver sizes. The Minnesota Vikings Hitch Cover, part # AH-10281, you have referenced will only fit a 2 inch hitch receiver. The
  view full answer...


• Measuring a Trailer Hitch Receiver to Determine Which Size It Is
• When choosing accessorizes for your trailer hitch, like the Minnesota Vikings Hitch Cover, # AH-10281, you measure the width of the inside of the receiver opening. The cover you have referenced will fit into a 2 inch receiver. The only Minnesota Vikings cover we have that will fit a 1-1/4 inch receiver is # FTH165SL. It is actually adjustable and will fit both a 1-1/4 and a 2 inch receiver. I have included a link to an FAQ on trailer hitch receiver sizes for you.
  view full answer...


• Is Hardware Included with the Atlanta Braves Logo MLB Trailer Hitch Cover # BHC402
• Everything is included with the Atlanta Braves Logo MLB Trailer Hitch Cover, # BHC402L, to install the cover in a 1-1/4 or 2 inch trailer hitch, except the hitch pin. I would recommend a Deadbolt hitch lock, # 7683, for 2 inch hitches, or # 7682 for 1-1/4 inch hitches, to secure the hitch cover when installed on the vehicle. I have added a link to all of the Atlanta Braves hitch covers for you to review.
  view full answer...


• Can a 2Inch Florida Gators Trailer Hitch Cover be Used with a Locking Hitch Pin
• Yes, you can use a locking hitch pin with the Florida Gators 2 inch Hitch Cover, # 034092100683. I recommend the DeadBolt Lock, # 7683, for 2 inch receivers. This will not only secure the cover to the hitch but also deter theft. The cover is made of metal. The only piece that is not metal is the foam gasket on the back. And, it is made in the U.S.A. I made a short video showing the compatibility of the cover and lock for you.
  view full answer...


• What Is The Diameter of the Face of the Iowa Hawkeyes 2 Inch Hitch Cover # 03409210154
• I went out into our warehouse and pulled a Iowa Hawkeyes 2 inch Trailer Hitch Receiver Cover # 03409210154 and found that it measures 4-1/16 inches in diameter. Check out the picture I attached to see how this measurement was taken. In order to determine how much of this cover would overhang on either side of your receiver hitch you will need to measure across the opening of your hitch and take that number and subtract it from 4-1/16 and divide by 2 to get how much the # 03409210154 would han
  view full answer...


• How Can I Get an Old School New England Patriots Logo on a Hitch Cover
• There might be a way for you to get an old New England Patriots on a hitch cover, but of all of the New England Patriot hitch covers that we carry none of them have the old logo on them. I searched on the internet and could not find any elsewhere either. What you could do is get a Blank Trailer Hitch Cover # TTBLANK114 and have an old school Patriots logo made for the cover. If you have a 2 inch hitch opening you would want a Blank Trailer Hitch Cover # TTBLANK2.
  view full answer...


• Do Hitch Covers Include a Hitch Pin or Lock
• The Hitch Covers we sell do not include the hitch pin. For a 2 inch receiver, you would either need a hitch pin, part # PC3 or a locking hitch pin, like part # 40107. As hitch covers are frequently stolen, I would recommend the locking hitch pin. If you should decide to go that route, make sure you write down your key number. With the key number, replacement keys can be obtained if necessary.
  view full answer...


• Will Indiana University Hitch Cover # 034092102311 Fit a 2008 Cadillac Escalade With Factory Hitch
• Your 2008 Cadillac Escalade should have a factory hitch size of 2 inches, but I would recommend to make sure by measuring the width of the opening on your factory trailer hitch. If it measures 2 inches then the Indiana University Logo Hitch Cover, part # 034092102311 will fit in your factory hitch. If your hitch does not have a pin and clip available, you will also need the Hidden Hitch Pin and Clip, part # PC3 to install the hitch cover to your vehicle. If you want to lock the hitch cover t
  view full answer...


• Is Alfred U.S. Marines Hitch Cover # 034092100737 Available with a Blue Background
• The Alfred U.S. Marines Hitch Cover, part # 034092100737 is only available in the red background with yellow lettering. They no longer offer the blue background. I am including a link to a product page that will list the 2 inch hitch covers that I have available that will reference the Marines.
  view full answer...


• How Thick is St. Louis Cardinals Stainless Steel License Plate SLP67
• I pulled one of the SLP67 license plates from our warehouse, and it is 1/32 of an inch thick. The mounting holes are 5/8 of an inch wide and 3/8 of an inch tall. We also offer a St. Louis Cardinal hitch cover, part # BHC423L, in which you might be interested if your 2011 Ford Fusion is equipped with a 1-1/4 inch trailer hitch.
  view full answer...


• Can the Iowa State University Hitch Cover # AH-10327 be Secured with a Locking Hitch Pin
• Yes, you can secure the Iowa State University Collegiate Hitch Receiver Cover, item # AH-10327, to your trailer hitch using a locking type of hitch pin. I would recommend the Deadbolt Lock for 2 Inch Hitches, item # 7683, for use with the hitch cover and any other ball mount that you may need to install in the hitch.
  view full answer...


• How Does Trailer Hitch Cover # 03409210151 Secure to the Trailer Hitch Receiver Opening
• The U.S. Army 2 Inch Trailer Hitch Receiver Cover, # 03409210151, fits into the 2 inch receiver opening and is wedged into place using 1 of 2 supplied wire inserts. These triangle shaped inserts fit into mounting holes on the back of the hitch cover and hold it into place using tension. The instructions state that you will then need to use a hitch pin, like # PC3, to secure the cover. I recommend using trailer hitch receiver lock # 7683 to both secure the cover in the receiver and to deter theft
  view full answer...


• Does State of Texas Flag Trailer Hitch Cover, # 034092101109 Come with a Hitch Pin
• A hitch pin, like # PC3, does not come with the State of Texas Flag Trailer Hitch Cover, # 034092101109. It comes with what are essentially retention clips that wedge it into the receiver opening. I recommend a locking hitch pin like # 7683 to secure the cover in the hitch and to deter theft. I have included a link below to a video review of the hitch cover and a link to a review of the locking hitch pin.
  view full answer...


• Will The Toys Go Here Hitch Cover For 2 Trailer Hitches # AH-10331 Fit A Toyota 2 Inch Hitch
• The Toys Go Here Hitch Receiver Cover, part # AH-10331, will fit a Toyota 2 inch hitch on a 2004 Toyota Tundra. The pin location is not the problem that we have encountered on the Toyota Tundra it is the length of the hitch pin that is needed. The Toyota hitch receiver has a heavier wall thickness, so you will need to use a hitch pin like the Hidden Hitch Pin And Clip, part # 74149. This hitch pin is designed for a 2 inch and a 2-1/2 inch hitch, and will work on your Toyota hitch. I am including
  view full answer...


• Where Is The U.S. Navy Retired 2 Inch Trailer Hitch Receiver Cover # 034092101413 Made
• I called the manufacturer (Siskiyou) and they said that the U.S. Navy Retired 2 Inch Trailer Hitch Receiver Cover # 034092101413 is made in the USA at their Medford, Oregon location.
  view full answer...


• How to Determine the Correct Hitch Cover Size for a 2009 GMC Yukon SLT
• Your 2009 GMC Yukon SLT should have a 2 inch receiver hitch installed on it, but you should check just to be sure before ordering. We have an FAQ article, see link, that shows how to measure the hitch to determine the correct accessories to order. If your Yukon does have a 2 inch receiver hitch then the Pink Ribbon Trailer Hitch Receiver Cover for 2 inch Trailer Hitches, item # 03409210234, will work great. At this time the the # 03409210234 is the only hitch cover we offer with the Breast
  view full answer...


• Can I Use A Lock To Secure U.S. Air Force Retired 2 Inch Trailer Hitch Receiver Cover
• The item you selected, U.S. Air Force Retired 2 Inch Trailer Hitch Receiver Cover, part # 034092101420, can be locked to your hitch. To lock part # 034092101420, you would need Trailer Hitch Receiver Lock, part # 7683, if you do not already have a locking hitch pin. I walked out to the warehouse and pulled part # 034092101420 and part # 7683 and took a picture of both in a 2 inch receiver and a picture of the back of the U.S. Air Force Retired Hitch Cover to better illustrate how it will f
  view full answer...


• Will a Receiver Lock Work on the Christian and Marines Alfred Hitch Covers
• Yes, the Alfred hitch covers can be secured with a locking hitch pin, like the C.T. Johnson Deadbolt Lock for 2 Inch Hitches, item # 7683. Both the Christian Fish 2 inch Trailer Hitch Receiver Cover, item # 034092100324, and the U.S. Marines Semper Fi 2 inch Trailer Hitch Receiver Cover, item # 034092100188, have metal mounting wire that secures the cover in the trailer hitch. If you have a Toyota Tundra a 2-1/2 inch receiver lock, item # RH5-XL, is required to fit through the 2 inch OEM h
  view full answer...


• What Size Trailer Hitch Will the Pink Ribbon Trailer Hitch Receiver Cover, # 03409210234 Fit
• The Pink Ribbon Trailer Hitch Receiver Cover, # 03409210234, is designed to fit in 2 inch square trailer hitch receiver openings. If your 2003 Chevy TrailBlazer has a 2 inch receiver, this cover will fit. The cover is held in place with 2 metal clips that act like springs and provide tension to hold the cover in place. I would recommend the Trailer Hitch Receiver Lock, # 7683, for a more secure connection and to deter theft of the cover.
  view full answer...


• USMC Hitch Cover for 1-1/4 Inch Receiver
• The USMC Hitch Cover you were interested in, part # 034092100737 will not fit a 1-1/4 inch receiver. For that size receiver we offer two USMC hitch covers part # 104047 or part # MHC602. I will provide links below to the hitch covers I have recommended. Semper Fi!
  view full answer...


• Dimensions and Material of the Tribal Skull Hitch Receiver Cover, # AH-10236
• I spoke with my contact at the manufacturer. The Tribal Skull Hitch Receiver Cover, # AH-10236, is made of cast pewter (metal) and is 4 inches by 4-1/2 inches.
  view full answer...