# 1
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 2
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
I pull a 20 ft. Travel trailer and had jackknifed backing up twice. The truck taillight creased the trailer. So I bought the extra long drawbar and have not had any problems since. Now I can also open the tailgate without hitting the tounge Jack.
# 3
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 4
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 12" Long - 5,000 lbs
The Ball Mount was noisy upon hitting bumps, uneven road, etc. I have since gone to a shorter, dampened ball mount but I have to remove the spare tire when I use it!!! Ruben
The receiver is exactly what I was looking for. Put it on a 2016 chevy traverse and it is the right length for pulling a trailer. Looked at 6 1/2 inch, too short. Quality is good also. I give it 4 stars.
# 5
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
This slightly longer than average bar was perfect for my application. The drop length was perfect also for the application. As usual, eTrailer's site and retail experience was first rate. Lots of info and specs (and videos) available makes it easier to get that piece of mind knowing that what you needed was what you ordered.
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 7
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 4" Drop - 7,500 lbs
All of the products I've have bought for my trailer project from etrailer have been great. My go-to place for anything trailer related!
Haven't set this up yet but quality feels good. User error on my part as this is not a ball I can replace but the flat bed I plan on buying for my motorcycle is a 2" so not a big deal and the price was a decent buy.
# 8
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.
Easy install, took around 30 minutes by my self to install. Hardest part of install was torquing the bolts ! Installed 13322 Class III Hitch - Gm 1500/2500 Pickup and Curt Class III Ballmount -2ball-2 Drop
# 9
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
I bought this on my knowledgeable brother's advice - he gave me the exact order number and link to buy from etrailer! I had it installed locally, without complications. I use my truck mostly to haul my horse or my friend's two donkeys in my 14-foot stock trailer. I have no complaints, the hitch does what it's supposed to do.
Easy install, everything included, and great instructional video. Worked out great for my RAV4.
# 10
Curt Ball Mount for 2" Hitches - 6-1/4" Rise, 7-1/2" Drop - 13" Long - 5,000 lbs
It is a Receiver!
The box it was shipped in had a hole in it, so the mount slipped out of the box when it was delivered. There was some minor paint damage from that, but the mount itself seems fine.
# 11
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
The one foot ball mount works great on a 2014 Chevrolet Silverado work truck(no lift kit). We use it for a one axle, lawn care/utility trailer. It is used at least half the work week and has held up for a year. It may not be a good choice for a heavier trailer, but at that point we would also purchase a 2500 truck too. The mount helps clear the jack when the tailgate is opened with about 2 inches to spare.
e trailer is my “go to” place for everything i need for towing my trailers great products - excellent selection - quick delivery and excellent customer service .
# 12
Ball Mount Adjustable with Sway-Control Tab, 6,000 lbs
The ball mount did not fit onto the shank. This was a very disappointing experience.
The fit of the U channel for the ball mount was too tight over the verticle drilled box tube. It needed “persuasion” to get it over the tube. This will make height changes away from the shop difficult. No rattle though.
# 13
Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Drop - 7,500 lbs
I haul a 5.5x10 open trailer w/ a 900 lb. ZTR, a push mower, and a handful of other tools 3 days a week. It is what it is. It does the job, no problem. A little finish wear and rust on the ball, but nothing major. I LIVE ON A DIRT ROAD, which is probably responsible for the wear.
The ball on this hitch is not spherical. If you clamp it into a trailer hitch, it rattles up and down (though not side-to-side). Other ball hitches in my arsenal (from different tow vehicles) are held snugly and don't rattle in any direction. Although not a safety issue, I don't like hearing the rattle on bumpy roads.
# 14
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
Great product, Fast shipping, Good Price
Well built using it on my Honda side by side to pull trailers gave me all the height I needed and moved the ball out to miss the muffler works great and very sturdy thanks again for another great part from etrailer
# 15
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Exactly what I needed to extend the reach of the ball beyond my rear tire carrier WITHOUT losing any tongue weight capacity! I used mine for the 2" rise.
Not usually a fan of any extra length between the truck and trailer, I opted for this extended ball mount so I could drop the tailgate without hitting the trailer jack. This did the trick. But this not a mount you should leave on your truck after detaching the trailer! Ouch!
# 16
Curt Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 9-3/8" Long - 10,000 lbs
10,000 Ball Mount, excellent price
Etrailer is always dependable to carry just the right supplies.
# 17
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
My order was missing installation parts, but the etrailer team were quick to correct the issue. Even without a lift, I was able to install the receiver and brake light cable quickly, thanks to their extensive video libray.
2024 CRV. Pretty straightforward install. The fish wires in the kit are a fantastic solution to holding the bolts. Thanks!
# 18
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
Needed a 3-ball tow bar (including the 3 most common sizes; 1&7/8", 2", & 2&5/16") for my 2" receiver, and bought the "mid-range" one in terms of towing capacity. It has a solid feel and will make switching ball sizes a breeze.
# 19
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
There were some UPS delivery issues, damaged in shipment. But, etrailer.com jumped right on sending out another shipment after it was apparent that UPS would not complete the delivery. The installation took longer, maybe 1-1/2 hours, because I did not have all my tools ready and I was working on the concrete floor in the dark to outside with a portable shop light. Everything fit well and it looks great. The 2" drop ball mount was the perfect height for my 2019 Toyota Highlander Hybrid. I love the look of the Curt black insert that makes the hitch looks like it belongs on the car, nothing embarrassing at all. Anything negative? Maybe. The flat plate was a little difficult to hook onto with the UHaul safety chains on a 5x8 trailer. That's hardly a negative, though, and I wouldn't have spent more on another brand choice because of this. Happy happy!
Excellent receiver kit! Combined with the curt trailer hitch and the oem Mazda trailer harness add on, this is legit!
# 20
Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers - 2" Hitch - 5" Drop/Rise - 10,000 lbs
This hitch is amazing!!! Be prepared though it is very heavy! I love how easy it is to adjust to different heights and ball sizes with the 2 common sizes provided. The scale on the back can be helpful to let you know if you have the proper trailer weight. The more you use it the more you will like it!
Love the height adjustment for all 3 of my trailers suuper solid, I get compliments all the time when people see it "wow that things stout!" Keeps the trailer tongue from excessive bobbing, the pins it came with are a huge improvement from the standard Bobby pin style I was used to. Over all I do not regret a dollar spent and would highly recommend to anyone looking for an initial purchase or upgrade their tow life
What our customers are saying:
"The phone operator was very helpful and made my purchase easy. I will keep this website handy."