Expert Answers about Trailer Jack

• Will the Ultra-Fab Ultra Scissor Jacks, # UF48-979002, Fit a 1999 Coleman Pop Up Camper
• The Ultra-Fab Ultra Scissor Jacks, # UF48-979002, will most likely fit your 1999 Coleman Santa Fe pop up. But to be sure you will want to determine if the 3-1/2 inch by 7-1/4 inch base on the jacks is the appropriate size for where you want to mount the jacks. The frame does not have to be exactly this size to accommodate the jacks but you will want enough surface area contact between the jack and frame to safely use the jacks.
  view full answer...


• Will a Bulldog Powered A-Frame Trailer Jack Fit a 2013-2014 Heartland North Trailer Travel Trailer
• To determine if the Bulldog powered A-frame trailer jack # BD500185 will fit your North Trailer 32buds, you will need to measure from the center of the jack hole opening back to that storage cover on the tongue. If it is more than 4 inches then the jack will fit. Any more than less inches and it will interfere with that cover on the tongue. The mounting pattern for the bolts will be the same as the manual jack on the trailer now.
  view full answer...


• Will Ultra-Fab Power Twin II Manual Stabilizer Fit a 2003 Keystone Cougar 5th Wheel Trailer
• The frame width on your 2003 Keystone Cougar 5th wheel trailer will need to be between 48 and 80 inches (measured from the outside of the frame on one side to the outside of the frame on the other side) in order for the Ultra-Fab Power Twin II Manual Stabilizer, # UF39-941704, to fit. The stabilizer has L-shaped brackets that fit on the frame and will be bolted into place. It is a straight forward installation and the average do-it-yourselfer should have no problem performing the installation
  view full answer...


• Would the Ultra-Fab Electric Landing Gear # UF17-943010 Fit a 2006 Forest River Cardinal 33LE
• Yes, the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010 that you referenced would work well for your 2006 Forest River Cardinal 33LE. I checked the dry weight of your trailer and this jack set should have plenty of capacity. To install this you will need to Weld hangers to front of trailer frame, beneath overhang Bolt jacks to hangers Mount switches anywhere on trailer for easy access
  view full answer...


• Will the Husky Brute Powered A-Frame Trailer Jack Fit a 2013 Keystone Bullet 23 BHS
• As far as the mounting hole pattern, the Husky Brute, # HT87247, has the standard pattern that most all A-frame trailer jacks use so that should not be a problem. You will have to make sure the hole diameter for the jack is at least 2-1/4 inches. This is one of the most slim jacks at the top that we offer so if there are tanks or storage areas on the frame behind the jack it should not be a problem with the Brute installed.
  view full answer...


• Clearance to Propane Tank Cover on Keystone Trailer of Control Housing on Bulldog Lift # BD500185
• The rear of the control unit housing on the Bulldog Powered-Drive Trailer Jack, part # BD500185, extends 4 inches behind the center line of the main down tube. On your trailer frame simply measure 4 inches back from the center point of where the round mounting bracket will attach to your trailer frame to determine where the back of the housing will be when installed. Please refer to the included photo.
  view full answer...


• Stromberg Carlson Landing Gear # LG-1 for Jayco Qwest Fifth Wheel Camper
• The Stromberg Carlson # LG-1 is an industry-standard landing gear that should fit on your fifth wheel with no problems. The mounting brackets weld directly to the frame of your fifth wheel, and the jacks would then mount into the brackets. As long as your Jayco Qwest has exposed frame members under the trailer loft for the brackets to weld to, the LG-1 will work great for you. I have linked you to a copy of our return policy.
  view full answer...


• Can Pro Series Square Trailer Jack PS1401010376 be Paired With Another Jack
• The Pro Series Square Jack, # PS1401010376, can work in tandem with another jack but it was not designed to have a mate that has a pin facing out opposite if # PS1401010376. What you can do is use # PS1400990376, which has the pin at the front. You would need to provide your own connection between the two jacks.
  view full answer...


• Will Ultra-Fab Deluxe Electric Landing Gear, # UF17-943010, Fit a 2003 Keystone Challenger
• The Ultra-Fab Deluxe Electric Landing Gear, # UF17-943010, has brackets that are designed to be welded to the vertical part of a 5th wheel trailer frame beneath the overhang. This makes it a universal type of application and should work well for your 2003 Keystone Challenger. You just have to inspect the trailer for the best place to weld the brackets.
  view full answer...


• Fulton F2 Swing Up Jack # F1413040134 for 2x3 Inch Trailer Frame
• The problem with trying to mount the Fulton F2 # F1413040134 on a 2x3 trailer frame is that the u-bolts do not have enough threads on them to draw the jack tight. If you can locate the appropriate u-bolts, you can by all means use them. You would need a u-bolt with a 3-1/2 inch span, center to center with legs no longer than 3 inches. Your best bet would be a weld-on model like # F1413060334.
  view full answer...


• Can a Gooseneck Trailer Stabilizer Jack be Used on a 5th Wheel Trailer with an Adapter Installed
• It sounds like you have the Anderson Ultimate connection # AM3225 or # AM3200. In either case since the adapter part that fits on the king pin can easily be removed I recommend going with a 5th wheel stabilizer, see link. You could use the gooseneck type and keep the adapter on but it is just one more link in the chain instead of a direct connection between the king pin and the stabilizer which would be more ideal.
  view full answer...


• Is Fastway Power Trailer Jack Flip-Foot Compatible with Stromberg-Carlson Electric Jack, # JET-3500
• Although the tube diameters of these two power jacks are similar, 2-1/4 and 2-3/16 inches, we do not recommend trying to adapt the flip-foot mechanism from the Fastway Power Trailer Jack to the Stromberg-Carlson # JET-3500. These parts are not intended for use with one another, so for safety considerations we cannot recommend that any of their components be mixed. My contact at Stromberg-Carlson confirms that a folding foot mechanism is neither available nor planned for use with the JET-3500.
  view full answer...


• Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch by 2-1/2 Inch Trailer Tongue
• Yes, the Pro Series Round Snap-Ring Jack, # PS1400300303, will bolt around your 2 inch by 2-1/2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer. I have attached a photo showing the bolt hole dimensions of this jack for you to check out.
  view full answer...


• Can I Replace Just One Jack on 2012 PJ Flatbed Trailer With Bulldog 2-Speed Jack, Part # BD183816
• In order for your existing single-speed trailer jack to work with the Bulldog 2-Speed Jack - Drop Leg w/ Spring Return, part # BD183816, it is essential that the existing jack have a cranking ratio (the number of handle turns that moves the jack one inch) that is the same as the 9-turns-per-inch high gear ratio of the Bulldog. If the two jacks do not have the same turns ratio, then the trailer will elevate unevenly, creating a safety hazard. My contact at Bulldog tells me that if the OEM jack
  view full answer...


• Stromberg Carlson JET-2500 Jack for Coachman Cascade Travel Trailer
• The Stromberg Carlson # JET-2500 Electric Trailer Jack you referenced has a lift capacity of 2500 lbs. The jack will work just great for trailers with tongue weights less than 2500 lbs, the tongue weight of your Coachmen Cascade should certainly be less than that. I have edited a photo for you showing the various dimensions and clearances related to the jack. The dimensions I provided should let you know if you will have clearance for your propane tanks.
  view full answer...


• Will Bulldog 10k Electric Landing Gear Fit a Crossroads Cross Terrain Trailer
• Bulldog makes a high quality and sturdy set of landing gear. I recently had the 12K model out of the box to check on the legs for a different customer and it is a solid set. To determine if the 10K set, # BD500161, is going to work for you take a look at the bracket height and lift specs. When retracted the bracket height is 29-13/32 inches and when extended 65-3/16 inches. You get a total lift amount of 36 inches. The drop leg makes up 18 inches and the other 18 inches is from the actual pow
  view full answer...


• Will the Ultra-Fab Power Twin II Electric Stabilizer Fit a 2013 Coachman Freedom Express 281RLDS
• The Ultra-Fab Power Twin II Electric Stabilizer, # UF39-941705, is designed to fit trailers and RVs with frames measuring 48 to 80 inches wide (measured from outside to outside). The brackets that attach to the frame are 36 inches long so there will need to be space on the frame at least this long for the brackets to fit. You will need to measure to determine if this unit will fit your 2013 Coachman Freedom Express 281RLDS.
  view full answer...


• Will 10K Bulldog Electric 5th Wheel Landing Gear Set Fit in Place of a 6.5K Set
• I spoke with my contact at Bulldog and he informed me that the 6.5k, 7k, and 10k landing gear sets uses the same mounting brackets so you can switch out the one you have with a higher capacity. On the 10k the overall height of the entire unit will be 4 inches taller than the one you have. The motor is 7-5/8 inches tall overall.
  view full answer...


• Will Pro Series A-Frame Trailer Jack # PSRV20000103 Fit a Haulmark Trailer
• The bolt pattern to mount an A-frame jack is a standard and the Pro Series jack, # PSRV20000103, also has slotted holes to allow for some variations in the pattern so it should work fine for you. Make sure that your current jack has an outer tube diameter of 2-1/8 inches so the new jack will fit. The Pro Series jack does not come with a foot or wheel. Your old foot might work if it fits around a 2 inch diameter lower tube. If you need a new foot use # PS1400700340. For a wheel use # PS1400750
  view full answer...


• Will Ultra-Fab Power Twin II Electric Stabilizer Fit on a 2013 Outback 300RB
• The Ultra-Fab Power Twin Electric Stabilizer, # UF39-941600, is a cross-frame mount unit. This means it mounts width-wise on the trailer. It can be mounted wherever you have the space to mount it including to the welded on square tube on the frame (assuming this piece is factory and not an aftermarket item) but attaching it directly to the frame would be best.
  view full answer...


• What is the Amperage Draw of Stromberg Carlson Powered A-Frame Trailer Jack # JET-2500
• When under load, the Stromberg Carlson jack, # JET-2500, draws 24 to 25 amps. Provided that the 12 volt battery on your trailer has the capability to provide this much power while running the other things tied into it or not, you can use this jack. Powered jacks with the same capacity, see link, have about the same power draw, no more than 30 amps.
  view full answer...


• Will the Fastway Power A-Frame Trailer Jack Fit a 2013 Keystone Outback 210RS Travel Trailer
• The 2013 Outback 210RS is going to be similar to the 2012 280RS in terms of clearance and the propane tank. You will want to go with a powered jack that provides the most clearance possible and that would be a jack like # FA88-00-7065. The only time you will run into trouble is if you had to manually crank the jack for any reason. The handle goes in at the top and based on images I saw of your trailer you would not be able to turn the handle a full 360 degrees.
  view full answer...


• Can the Weld-On Fulton F2 Swing-Up Jack be Installed on a 6 Inch Trailer Frame
• Actually, you could weld the Fulton trailer jack # F1413200334 to a 6 inch frame if you wanted. Fulton does list the weld-on jacks as fitting a certain frame size but if the frame is a little larger it would not be an issue. As long as there is enough surface area for a proper weld you can use this jack.
  view full answer...


• Center Hole Measurement on the mounting Bracket for Pro Series Trailer Jack PS1401030303
• I went out to the warehouse and measured a Pro Series trailer jack # PS1401030303. The center hole will fit around a 2 inch diameter pipe. The bracket will need to be welded to the trailer frame. You will want to measure the round pipe on your trailer to determine if this jack will fit.
  view full answer...


• Can the Bulldog Pipe Mount Swivel Sidewind Jacks # BD158109 and # BD158151 Use the Same Weld-On Pipe
• I verified with my contact at Bulldog that the Bulldog Pipe Mount Swivel Jacks, # BD158109 and # BD158151, can use the same weld-on pipe. The 15 inch jack # BD158151 does use a slightly larger 9/16 inch pin because the pin hole on the jack is larger. The pin hole on the weld-on pipe can accept a 1/2 inch or a 9/16 inch pin. The footplate and pin are included with the jack.
  view full answer...


• Will Ultra-Fab Rear Electric Stabilizer, # UF39-941602, Fit a 2012 Heartland Cyclone 3800
• You will need to measure the frame on your 2012 Heartland Cyclone 3800 to determine fit of the Ultra-Fab Rear Electric Stabilizer, # UF39-941602. It will fit on frames that measure 66-5/8 inches to 69-5/8 inches wide. Many travel trailers have a frame that is actually 74 inches wide. A similar powered unit, # UF39-941705, is rated for 6,000 pounds and fits frames 48 to 80 inches wide.
  view full answer...


• What Size Socket Fits on the Ultra-Fab Ultra Scissor Trailer Jack
• The not that turns the worm gear on the Ultra Fab jack, # UF48-979006, is a 3/4 inch. You can use the Ultra Fab speed socket, # UF48-979005 with a drill that accepts 3/8 inch drive bits to extend/retract the jack faster.
  view full answer...


• Boat Trailer Jack For a 1998 Shorelander Trailer with Original Snap Ring Jack
• The inside diameter of the snap ring for the Fulton Trailer Jack, # FTJ120W0301, is 2.28 inches, and is designed to fit in the 2-1/2 inch retaining groove on the mounting plate. As long as the diameter of the retaining groove on your jack mounting plate is 2-1/2 inches this jack will work. This is the highest capacity jack that we have that has a snap ring attachment. Jacks with higher capacities have different attachment systems.
  view full answer...


• Will Ultra Fab Stackable Stabilizers # UF48-979004 Prevent Movement When Walking Across Coachman RV
• The Ultra-Fab Stackable Stabilizers you mentioned, part # UF48-979004 are specifically designed to provide stability for your trailer, thus eliminating the movement felt when you are moving about in the trailer. They would make a good complement to your factory installed jacks. Due to the fact that they do not take up much storage space and their affordable price, the Ultra-Fab Stabilizers are a very popular item.
  view full answer...


• Recommendation For Trailer Jack To Fit a 3 Inch Wide and 5 Inch Tall Aluminum I-Beam Trailer Frame
• I would recommend to use the correct trailer jack for the 3 x 5 inch trailer frame, instead of trying to modify something to work. The Fulton F2 Trailer Jack, part # F1413130334, that you have referenced is designed for 4 x 5 inch trailer frames. The Fulton Trailer Jack, part # FXP15, with a single wheel and the Fulton Trailer Jack, part # FXPD15L, with the dual wheels are both rated at 1,500 lbs. They are both designed to bolt-on to a 3 x 5 inch frame. It would work fine on your aluminum I-b
  view full answer...


• Will the Pro Series Swivel Trailer Jack, # PS1401440303, Fit a 7 Inch Trailer Frame
• The Pro Series swivel jack, # PS1401440303, includes a separate male pipe that you will need to weld to the side of the trailer frame. Provided you have a clear spot on the side of the frame you can attach it to the 7 inch frame. Any welding should be done by a qualified professional.
  view full answer...


• Swivel Trailer Jack Recommendation for a 6 Inch Tall Trailer Frame
• The Fulton Bolt-Thru Swivel Marine Jack, # FXP15, fits a 3 inch by 5 inch frame. A 6 inch frame is going to be too tall for this jack. The best option for you would be a weld-on swivel jack, # 5876A8. This jack does have a wheel, it has 1,500 pounds capacity, and it will fit the 6 inch frame on your trailer. The welding should be done by a qualified professional.
  view full answer...


• What is the Width and Diameter of the Wheel/Castor Of the Bulldog Heavy-Duty Jack
• I went out into our warehouse and measured the wheel of the Bulldog Heavy-Duty Jack # BD165412 that you referenced and found that the wheel is 2-5/8 inches wide and 5-3/4 inches in diameter. Check out the picture I attached to see these measurements.
  view full answer...


• Hole Dimensions of Snap Ring Bracket for Fulton Snap Ring Swivel Jack Part # FTJ12000101
• The hole in the bracket of the Fulton 1200 lb Snap Ring Swivel Jack is 2.55 inches in diameter to accommodate the 2-1/2 inch diameter flange on the trailer mounted bracket that the snap ring attaches to. The 2-1/2 inch diameter flange on the trailer bracket passes through the 2.55 inch diameter hole in the bracket on the jack. The holes that the retaining swivel pin passes through are 3 inches apart on center. I have produced a photo of the snap ring bracket included with the above mention
  view full answer...


• Ultra-Fab Electric A-Frame Jack # UF38-944016 for 2009 Keystone Outback Toy Hauler
• According to the information I was able to find, the Ultra-Fab Electric A-Frame Jack you referenced, part # UF38-944016 would be a good choice for the Keystone Outback Toy Hauler you mentioned. The jack has a 3500 lb lift capacity, which is plenty for the listed tongue weight of the toy hauler, plus anything stowed on it. Among the many features of this jack, I like the fact that is uses LED lamps for long life as well as the fact that a 9/16 inch socket wrench can be used in an emergency
  view full answer...


• Swing Up Jack Needed for a Coleman Trailer with a Battery Box Mounted on the Tongue
• As long as the tongue on your trailer is a 3 x 3 or 3 x 4 inch tongue, the Fulton F2 Trailer Jack, # F1413040134, that you mentioned should work great. The Pivot point on this jack is adjustable. I produced a short video, see link, showing how to adjust the mounting bracket so you can determine if there is clearance for the battery box on your trailer. At the highest point the center of the swivel is 6-1/2 inches from the top of the jack. This should give you clearance to mount the jack and s
  view full answer...


• Effectiveness of Ultra-Fab King Pin Tripod Stabilizer # UF19-950200 with TrailAir Tri-Glide Pin Box
• The Ultra-Fab 5th Wheel King Pin Tripod Stabilizer, part # UF19-950200, will work with your TrailAir Tri-Glide Pin Box. It will still be beneficial because it will help transfer the weight of the fifth wheel to the tripod stabilizer and help eliminate the front to back and side to side motion of your fifth wheel after it has been unhitched. The tripod stabilizer will still be effective and give the needed support at the front of your fifth wheel even with the air bag in your Tri-Glide pin bo
  view full answer...


• Is the BullDog Power Drive Trailer Jack the Correct Jack for a 3 Horse Trailer with Living Quarters
• The Bulldog Power-Drive Trailer Jack, # BD500185, will work great on your 3 horse trailer with living quarters, as long as the tongue weight of the trailer is less than 4,000 lbs when loaded and ready to tow. You will also need to make sure there is room for installation of the jack. The head of the jack measures 11 inches tall, 4-1/2 inches wide and 8-3/4 inches deep, see photo link.
  view full answer...


• Will the Fulton F2 Swing-Up Trailer Jack Fit a 1978 Apache Trailer with 3 Inch Frame
• The Fulton F2 Swing-Up Trailer Jack, # F1413020134, fits up to 3 inch by 4 inch frames, so there is a good chance it will fit your trailer frame. The mounting bracket for the jacket has 8 inches of travel along the main body of the jack if you need more or less length and if you have limited space on your trailer frame. We also have the Fulton F2 Swing-Up, Wide-Track Trailer Jack, # F1413040134, that fits 3 inch by 3 inch or 3 inch by 4 inch frames.
  view full answer...


• Will Pro Series A-Frame Jack # PSRV20000103 Fit in Same Mounting Holes as Older Fulton F2 Jack
• The mounting holes on the Pro Series Round, A-Frame Sidewind Jack, part # PSRV20000103, are elongated holes that are 3 inches from the center of one hole to the center of the next hole. This is a industry standard dimension for A-Frame jacks. If the caster you have on your Fulton F2 jack will fit a 2 inch diameter tube, your caster will work in this jack. The Fulton caster and Pro Series caster like the Pro Series 6 Inch, Detachable Caster, part # PS1400750340, will usually interchange with e
  view full answer...


• Will the Pro Series 5K Pipe Mount Swivel Trailer Jack Work on a 2,500 Pound Dump Trailer
• The Pro Series Square Swivel Jack, # PS1401610383, has a 5,000 pound capacity. Since the jack is mounted on the tongue near the front of the trailer, this should be more than enough capacity for your application. It is unlikely the tongue weight of the trailer will be as great or greater than 5,000 pounds so this jack should work well in that respect. This is a pipe mount swivel jack, so you will need to make sure there is room on the trailer for the jack to swing up. It will need at least 17
  view full answer...


• Will Pro Series Square Swivel Jack # PS1401520383 work w/ Mount Tube For Bulldog Jack # BDPG9810-00
• I contacted our representative at Pro Series about the compatibility of the Pro Series Square Swivel Jack # PS1401520383, and the Mount Tube for Bulldog Round Jack, part # BDPG9810-00. He informed me that the Bulldog Mount Tube will work with the Pro Series Jack. Both the Bulldog Mount Tube and Pro Series will attach to each other, but the Bulldog Mount will need to be welded to the trailer. However, the Pro Series Swivel Jack # PS1401520383 comes included with a mount.
  view full answer...


• Will a Fulton Trailer Jack Fit the Same Weld On Mount Used by a Shelby Jack
• It is possible that you can reuse the same mount. It depends on the style of the jack you have and the one you want to replace it with. For example, the Fulton Round, Snap-Ring Swivel Marine Jack, # FTJ120W0301, has a mounting bracket with an inner diameter of 2-1/2 inches. It uses a 3/8 inch pull pin. If it does not match what you have on the trailer, the jack does come with a new weld-on bracket that you can use.
  view full answer...


• Will Pro Series Trailer Jack Part # PSEJ10000101 fit a 3 Inch Trailer Tongue
• The Pro Series Snap-Ring Swivel Jack you referenced, part # PSEJ10000101 will fit your 3 by 3 inch trailer tongue.
  view full answer...


• Would the Leveling Jacks # JSC-30 Work as Replacement Jacks on my Coleman Utah Pop-Up
• These Leveling Scissor Jack Set # JSC-30 have a capacity of 5,000 lbs per jack. As long as you would not be asking the winch to handle more than 5,000 lbs each these jacks would work well as replacement leveling jacks on your Coleman Utah pop-up camper.
  view full answer...


• How To Determine if Fulton Round, Snap-Ring Swivel Jack # FTJ120W0301 Will Fit Existing Weld Mount
• To determine if the Fulton Round, Snap-Ring Swivel Marine Jack, part # FTJ120W0301, will fit on your existing weld mount on your trailer you will need to measure the diameter of the weld mount on your trailer. The inner diameter of the large mounting hole on the center of the mounting bracket for Fulton Jack, # FTJ120W0301, is 2-1/2 inches. The Fulton jack also uses a 3/8 inch size pull pin. This jack will also come with a new weld-on mounting bracket in case it will not fit your older mounti
  view full answer...


• Outside Dimensions of the Outer and and Inner Tube on the Pro Series A-Frame Top Wind Trailer Jack
• The outer tube diameter where the mounting flange is welded on to the Pro Series Round, A-Frame Jack, item # PSEA20000103, is 2-1/4 inches. The inner tube that extends and retracts has an outer diameter of 2 inches, see photo. At this time we do not have a Jack with an outer tube diameter of 1-7/8 inches and inner tube diameter of 1-5/8 inches. Your best options would most likely be to enlarge the hole in your mounting plate for a 2-1/4 inch diameter jack or to go with a frame mounted option
  view full answer...


• Which Support Plate Can be Used with Pro Series A-Frame Trailer Jack # PSEA20000103
• The outer tube diameter of the Pro Series A-frame Trailer Jack, # PSEA20000103, is 2-1/4 inches, so you will need a support plate with a hole diameter larger than that. The Bulldog Jack Support Plate, # BDSPB50, has a diameter of 2-9/32 inches, slightly larger than the jack tubing, so it will work. And Bulldog Jack Support Plate, # BD003135, is a little larger than that at 2-11/32 inch diameter. Either of these plates should be a good fit.
  view full answer...


• Will the Fulton F2 Swing-Up Jack work with a 12 Foot Coleman Pop-up Camper
• As long as the tongue framing on your Pop-up Camper is 3x3 or 3x4 inches and you will have clearance to rotate the side wind crank 360 degrees at the side of the trailer, the Fulton F2 Swing-Up Jack # F1413040134, should work great. If your trailer frame is not this size or you do not have clearance to rotate the handle, send me a photo of the jack you have and I will be glad to make a recommendation for you.
  view full answer...


• Will Atwood Trailer Jack # 273400 Fit a 1995 A-Frame Float-On Trailer
• The Atwood Trailer Jack, # 273400, is designed to fit the standard bolt pattern of A-frame jacks. The outer tube diameter is 2-7/32 inches in diameter so you will need to make sure that the trailer can accept this size tube. You may also be interested in adding a bottom support plate, # DL22763, to the trailer if it does not already have one. This bottom plate is a weld-on application and any welding will need to be performed by a qualified professional. This jack does not come with a wheel o
  view full answer...


• Installation Details For The Atwood RV Landing Gear # 75333 On A 1996 Fleetwood Mallard
• If the Atwood RV Landing Gear # 75333 can be mounted between 52 and 74 inches apart and as long as the pin or tongue weight of the trailer when fully loaded and ready to tow is less than 6,000 lbs, you will be able to use the Atwood RV Landing Gear, part # 75333. The Atwood RV Landing Gear # 75333 is designed as a bolt-on application. This landing gear has a manual crank to raise and lower. If you prefer an automatic operation, we have the Electric Motor for R.V. Landing Gear, part # 75391.
  view full answer...


• Will Pro Series Trailer Jack # PSEA20000340 Replace a Shelby # 5793-24Z
• According to the research I did, the Pro Series Round, A-Frame Jack, # PSEA20000340, is comparable to the Shelby jack you have referenced. There are some minor differences. First, they both fit the standard A-frame mounting pattern and have a 2,000 pound capacity and have a top wind design. The differences are in the dimensions. According to Shelby, their jack has 15 inches of travel, the Pro Series has 14 inches of travel. The extended length from the mounting bracket to the bottom of the
  view full answer...


• What is the Difference Between a Horizontal Clevis Crank Handle and a Vertical Clevis Crank Handle
• The clevis in regards to Bulldog 2-Speed Jack, part # BD183816, is the style of the crank handle for the jack. The difference is in the alignment of the pivot point to the rest of the crank handle. A horizontal clevis crank handle when folded up will pivot almost like a wing and lay flat on the side of the trailer when not in use, whereas a vertical clevis crank handle will pivot in like an elbow and fold in to the trailer and be secured in place. In order to pick the right one for your ap
  view full answer...


• Mounting Fulton Swivel Marine - Weld On Jack # FTJ120W0301 To Replace Exising Fulton Jack
• I contacted our representative at Fulton about the Fulton Round, Snap-Ring Swivel Marine Jack, part # FTJ120W0301. The inner diameter of the mounting hole is 2-1/2 inches. He informed me that up to a few years ago the Fulton jacks were made in Wisconsin, but are now made in China. At that time the mounts were tightened up, so the mounting holes were changed slightly. He informed me that part # FTJ120W0301 includes a new weld-on mount and chances are that you may have to replace your weld on m
  view full answer...


• What Is Total Overall Length and Width of Pro Series Trailer Jack # PS1401060303 When Retracted
• I walked out to our warehouse and took some measurements of the Pro Series Trailer Jack, part # PS1401060303. Yes, the Pro Series Jack # PS1401060303, will be able to rotate into a 17-1/2 Inch space if the the jack is retracted. The overall height of the jack when retracted is less than 17 inches, and will clear no problem. I measured the width of the mount and the tube and it measured 5 inches wide. The total width from the mount to the end of the handle measured 9-3/4 inches.
  view full answer...


• Will Bulldog Powered-Drive Trailer Jack, # BD500186 Work on a 4,700 Pound Travel Trailer
• The total lift capacity of the Bulldog Powered-Drive Trailer Jack, # BD500186, is 4,000 pounds. If mounted on the tongue of the A-Frame trailer, the tongue weight cannot exceed 4,000 pounds. If you do not know the tongue weight of your travel trailer, it is typically 10 to 15 percent of the gross trailer weight. For a trailer weighing 4,700 pounds, the tongue weight would be 470 to 705 pounds. The jack mounts on a standard A-frame trailer, most of which use the same bolt pattern for mounting
  view full answer...


• Will the Bulldog Round, Snap-Ring Swivel Jack # BD151443 Fit on a 2 inch by 5 inch Trailer Frame
• We have several options for a bolt on swivel jack for your trailer with 2 by 5 inch frame (see link). I would recommend the Pull Pin, Easy Swivel Trailer Jack with 8 inch Wheel - Sidewind - 1,500 lbs. by Dutton-Lainson, item # DL22800, for your trailer if the 1500 pound capacity is sufficient for your boat and trailer. These jacks are high quality and designed to fit square tongues up to 3 x 5 inches. The Bulldog Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10 inch Lift - 2,000 lbs, ite
  view full answer...


• Does Pro Series Powered Trailer Jack PS500198 Have a Full 18 Inches of Height
• The Pro Series powered A-frame jack # PS500198 has 18 inches of lift, meaning that the leg would measure 8-1/2 inches down from the mounting bracket when retracted, or 26-1/2 inches when extended. Basically, you will still have the 8-1/2 inches of leg extending downward when the jack is completely retracted. If you need the trailer to be lowered more, you would look for a shorter bracket height. For example, A-frame jack # BD155033 would have a bracket height of 5-13/16 inches when fully ret
  view full answer...


• Will Crossframe-Mount Stabilizer Jack, # 76856 Fit on a 1971 Airstream Trailer
• As long as the frame on your Airstream is between 64 and 74 inches wide and is rated for use with this type of jack, then the Crossframe-Mount Stabilizer Jack, # 76856, will work. The 16 or 17 inches from the ground to the frame is within the limits of this jack. It will go up to 19 inches between the ground and frame but no higher. You may also be interested in the CP Products Stabilizer Jack Foot Pads, # 76851. These feet are designed to work with the jack you have referenced will provide i
  view full answer...


• Can the Internal Parts of A Pro Series Jack Fit Inside the Housing of a Comparable Bulldog Jack
• The best solution would be to replace the handle on your existing Bulldog Jack, # BD171401. You will need Replacement Topwind Handle for Bulldog Round Jacks, # BD500180. I did speak with my contact at Reese and Bulldog and he stated that the internal parts of the Pro Series Jack, # PS1401460303, cannot be removed. The jack is designed not to come apart, so you will not be able to make the switch.
  view full answer...


• What Fulton Trailer Jack Will Fit A 3 Inch X 3 Inch Trailer Tongue And Be Used Around Salt Water
• The Fulton F2 Trailer Jack, # F1413140334, you have referenced is designed for a 4 inch X 5 inch trailer tongue. It will not fit your 3 inch X 3 inch trailer tongue. The same jack to fit your 3 inch X 3 inch trailer tongue would be the Fulton F2 Trailer Jack, # F1413040134. This is the same corrosion-resistant jack that will work for marine applications. It can be used in and around salt water. It comes with the mounting hardware for a 3 inch X 3 inch trailer tongue. The Fulton line of jac
  view full answer...


• Will Atwood or Bulldog Powered Trailer Jacks Fit a Jayco Jayflight Travel Trailer # RKS-31
• I went out to the warehouse to measure both of the jacks. The Atwood Power Trailer Jack with Cover and Foot, # AT80718, has a 3 bolt pattern. The center to center distance between the bolt holes is 3 inches. It is designed for A-frame trailers. The mounting bracket is more of a triangle shape. The Bulldog Jack, # BD500185, is also made for A-frame trailers, but it has a different bolt pattern because it has 6 holes for a wider variety of mounting options. Center to center Distance between bol
  view full answer...


• Which Fulton F2 Swing Up Jack can I use for my Boat Trailer
• I will get ahold of Fulton to gather some dimension information. In the meantime, when the trailer is level, what is the measurement from the ground to the top of the trailer frame?
  view full answer...


• Is Mounting Hardware Included With The Dutton-Lainson Trailer Jack, # DL22580
• The Dutton-Lainson Trailer Jack, # DL22580, does come with all the mounting hardware. The mounting hardware that comes with the jack is the Dutton-Lainson Mounting Hardware, # DL22443. It will fit trailer tongues up to 3 inches X 5 inches, so it will fit your trailer securely. The jack has a 12 inch lift and a capacity of 1,500 lbs. I am sending a video link of a similar jack being installed on a trailer.
  view full answer...


• Will the Replacement F2 Swivel Jack fit a Mastercraft Boat Trailer with Weld On Swing Up Jack Plate
• To determine if the Fulton F2 Swing-Up Trailer Jack with Dual 7 inch Wheels, Sidewind -1,600 lbs - No Mounting Hardware, item # F1413100334, will bolt directly to the old bolt through mount, without cutting it off, you will need to measure the bolt pattern on your trailer. I went out to the warehouse and measured the bolt mounting pattern on the Fulton F2 Swing-Up Trailer Jack, item # F1413100334, and the bolt holes are 3-3/8 inches on center by 4-3/8 inches on center. If you determine tha
  view full answer...


• Mounting Bolt Pattern of the Bulldog A-Frame Jack and is Hardware Included
• The bolt holes on the Bulldog Round, A-Frame Jack, item # BD1700100317, triangle mounting flange are 3 inches from center of one hole to the center of the next hole. They are equally spaced apart and they are elongated for easier installation. A-Frame jacks are all the same size and have the same bolt-pattern. The manufacturers did this so they could simplify the manufacturing process for both bolt-on and weld-on A-frame jacks. The jack can be bolted on, hardware not included, or it can be
  view full answer...


• Will Pro Series Snap-Ring Swivel Marine Jack, # PSEJ10000101, Fit a 3 x 3 Inch Square Trailer Frame
• The Pro Series Snap-Ring Swivel Marine Jack, # PSEJ10000101, will fit trailer frames up to 3 by 5 inches, so it will fit on your trailer. You will need to use 1/2 inch bolts. I recommend grade 8 bolts for this application.
  view full answer...


• What Tubular Swivel Trailer Jack Is Available To Replace A Bulldog 170 Series
• The Bulldog Trailer Jack, # BD195304, you have referenced is a direct weld jack. A similar jack to the # BD195304 in a tubular swivel mount with a round mount would be the Bulldog Round, Pipe-Mount Swivel Jack - Topwind, # BD178151. It has a 5,000 lbs. support capacity, 15 inches lift and is a topwind. The Bulldog Round, Pipe-Mount Swivel Jack - Sidewind, # BD178203, is a tubular swivel mount with a round mount and it also has a 5,000 lbs. capacity, 15 inches of lift, but it is a sidewind
  view full answer...


• Can Husky Crossframe-Mount Stabilizer Jack, # 76854, Be Modified To Fit Pop-Up Camper
• The Husky Crossframe-Mount Stabilizer Jack, # 76854, is designed for frame widths of 64 inches to 74 inches. We cannot recommend modifying this product to fit your application because it is tested at the manufacturer for a 2,000 lbs. static load capacity and any altering to the product will change the capacities and safety of that product. We do have the Domar Stabilizer Jack - 1,000 lbs, # TJ01RT, which is designed for pop-up campers. It has a capacity of 1,000 lbs. and can be bolted on or w
  view full answer...


• Trailer Jack Recommendation for 25 Foot Roadrunner Trailer with a 7,000 Pound Boat
• If your boat and trailer together weigh 7,000 pounds, that could mean you have a tongue weight over 1,000 pounds. In this scenario, I would not recommend the Fulton Snap-Ring Swivel Marine Jack, # FEJ1000, as it has a max capacity of 1,000 pounds. Instead I would go with the next step up to be on the safe side. Take a look at the Fulton Bolt-Thru Swivel Marine Jack w/ Caster - Sidewind - 10 inch Lift - 1,200 lbs, # FXP10. This is very similar to the jack you referenced but it has a capacity
  view full answer...


• Will Bulldog Round A-Frame Jack Fit a Wells Cargo Trailer
• All A-Frame mounted jacks like this Bulldog jack, use the same bolt pattern. In other words, those mounting holes are a universal size and pattern that way any A-Frame jack will fit into any A-Frame jack mount. As long as your Wells Cargo has an A-Frame jack mount, this jack will fit.
  view full answer...


• Fit of Fulton Fulton Trailer Jack, # F1413040134, on Dual Jet Ski Trailer
• The Fulton Trailer Jack, # F1413040134, will fit 3 inch x 3 inch and 3 inch x 4 inch tongues and has a capacity of 1,600 lbs. If your dual jet ski trailer is under 1,600 lbs with jet skis and has either one of those tongue sizes it should work.
  view full answer...


• Replacement Handle for a Fulton # FXP10 Sidewind Swivel Trailer Jack
• The correct replacement handle for the Fulton Bolt-Thru Swivel Marine Jack w/ Caster - Sidewind - 10 inch Lift - 1,200 lbs, item # FXP10, is the Replacement Sidewind Handle Kit for Fulton Marine Jacks - 800 lbs, F0933301S00. I spoke with my contact at Fulton and he assured me that this is the replacement handle for your 1,200 pound jack.
  view full answer...


• Shaft diameter on the Bulldog Powered-Drive Camper Jack # BD500185
• The Diameter of the main tube is 2-1/4 inches on the Bulldog Powered-Drive Camper Jack, item # BD500185. There are 6 holes in the mounting plate for either 2-1/2 inch mounting pattern or 3 inch mounting pattern. These are the standard bolt patterns used by most trailer manufacturers.
  view full answer...


• Trailer Tongue Frame Sizes Dutton-Lainson Trailer Jack , Part # DL22320 will Fit
• I checked with the manufacturer, and Dutton-Lainson trailer jack, part # DL22320 will fit up to a 3 inch frame channel with the bolts provided. If your channel is wider, you would be able to make the jack fit using longer bolts.
  view full answer...