Expert Answers about Trailer Jack

Trailer Jack

Will Stromberg Carlson Replacement Follow Jack # LG-179014 Fit On Fleetwood Prower Lynx Camper
After consulting with Stromberg Carlson, I have found that the Stromberg Carlson Replacement Follow Jack # LG-179014 is a compatible replacement for the follow leg on your Fleetwood Prower Lynx 5th-Wheel camper. This item replaces the follow jack for your tandem landing gear. It is the jack in the landing gear that does not have a crank or motor mounted to it. It works with most brands of landing gear and is constructed of heavy-duty steel. It has a lift of 21 inches from the weld-on point
view full answer...

Replacing OEM Electric Landing Gear on a 2009 Heartland Cyclone 3950 5th Wheel Trailer
To determine if the Ultra-Fab Deluxe Electric Landing Gear Set, # UF17-943010, or the Bulldog Electric Fifth Wheel Landing Gear, # BD500161, will fit with your existing clamps, we will need to find the space between the clamps. The Ultra-Fab and the Bulldog landing gears will mount to the clamps different ways. The Ultra-Fab set requires the clamps to sit on top of each weld stop on the landing gear legs. For the Ultra-Fab set to fit, the distance between the bottom of your lower clamp and t
view full answer...

Difference Between Ultra-Fab Scissor Jack Part Numbers UF48-979032 and UF48-979031
The Ultra-Fab Ultra Scissor Jacks # UF48-979031 that you referenced is a quantity of 2 of the Ultra-Fab Ultra Scissor Jack # UF48-979032. So its the same jack, but one part number you get a pair of them and the other part number you get just one.
view full answer...

Powered Bulldog Jack Recommendation for a 24 ft Flatbed Gooseneck Trailer with Camper
The best recommendation I can give you would be to replace your current jack with a Bulldog Jack like our part # BD182804 and then get a Bulldog Powered-Drive Kit # BD1824200100. The powered drive kit is only confirmed to fit Bulldog jacks so you would not be able to install the kit on your current jack.
view full answer...

Which Way Will the Handle Face on the Dutton-Lainson A-Frame Trailer Jack # DL22530
The orientation of the handle on the A-frame trailer jack # DL22530 will depend on the hole pattern on the trailer. The jack uses a 3 hole pattern that is basically in the shape of a triangle. The handle will be in a different place depending on how you want to mount it. Normally, the handle would be off to the left side of the trailer.
view full answer...

Recommendations for Side-wind Pipe-Mount Weld-On Swivel Jacks Rated for 5000-8000 Lbs
We offer the Bulldog Round Pipe-Mount Swivel Jack rated for 5000 lbs, part # BD178203. This includes the 2-inch weld-on coupler pipe (and retaining pin and clip) and the foot plate. This jack offers 15 inches of lift. Please refer to the video link provided. We also offer the Bulldog Square Swivel Jack, part # BD190758, which also provides 15 inches of lift, includes the 2-inch weld-on coupler pipe, pin and clip, and footplate. This jack is rated for 8000 lbs static capacity and also offers a
view full answer...

Trailer Dolly Recommendation for a Boat Trailer with a Tongue Weight Under 600 lbs
For a trailer dolly that will work with your boat and trailer, I would recommend looking at the Buffalo Tools Trailer Dolly, # BTTRDOLLY. This trailer dolly has a tongue weight capacity of 600 lbs which is the highest tongue weight capacity of our trailer dolly selection. This trailer dolly comes with a 1-7/8 inch hitch ball that makes it easy to use with multiple trailers that use different hitch ball sizes.
view full answer...

Fully Retracted Length of Fulton Swivel Jack Part # FXP10W0301
The overall length of the Fulton # FXP10W0301 jack you referenced is just slightly less than 24 inches, therefore it would be longer than what you are looking for. I took a look at the rest of the jacks rated for 1,200 lbs, and found that they are all of roughly similar length. If a 2,000 lb capacity jack that uses a foot plate instead of a caster would work for you, I would recommend the Pro Series Pipe-Mount Jack, part # PS1401060303. Fully retracted, the jack measures 17-1/4 inches lon
view full answer...

Does Dutton-Lainson Sidewind Swivel 1200 Pound Trailer Jack Have to be Lubricated
Jacks like # DL22300 come greased already and normally you would not need to add any grease unless excessive dirt, moisture, or corrosion got inside. Take the cap off of the top of the jack to inspect the gears. Inspecting the nut and screw inside would require removing these gears. If corrosion has built up on the screw and nut then that could be causing the problem. If additional grease is needed you will need to make sure to use a compatible grease or remove all the old grease before addin
view full answer...

Will the Ultra-Fab Ultra Scissor Jacks, # UF48-979002, Fit a 1999 Coleman Pop Up Camper
The Ultra-Fab Ultra Scissor Jacks, # UF48-979002, will most likely fit your 1999 Coleman Santa Fe pop up. But to be sure you will want to determine if the 3-1/2 inch by 7-1/4 inch base on the jacks is the appropriate size for where you want to mount the jacks. The frame does not have to be exactly this size to accommodate the jacks but you will want enough surface area contact between the jack and frame to safely use the jacks.
view full answer...

What is the Diameter of the Round Base on Ultra-Fab Stackable Stabilizers, # UF48-979004
I went out to the warehouse and measured the round base that contacts the bottom of the trailer for Ultra-Fab Stackable Stabilizers, # UF48-979004. It measures 1-3/4 inches in diameter. I made a video with this information and a picture as well. In terms of using this item to support a door to create a porch on a trailer you will have to determine if the door is rated for the weight associated with being a porch. The construction of the door may not be conducive to porch-ness.
view full answer...

Bolt On Trailer Landing Gear Jack for a 24,000 Pound Trailer
Bulldog jack # BD500154 is very much overkill for a 12 ton trailer but also one of only a few we are going to have for 24,000 pounds. The manufacturer has not provided us with images and we have not yet had the item in to take pictures. But it is a landing gear set not unlike # BD500153 which is the weld-on counter part. We also have a 45K option, # BD1839060383, bolt on or # BD1839050383 weld-on. For 25K we have some options that I have linked for you but they are all weld on.
view full answer...

Ultra-Fab Steel Tripod Stabilizer Extensions
Since you have the steel tripod stabilizer, # UF19-950500, you would need the steel extensions # UF19-950002. Like you said, the extensions are 8 inches long. There are a total of 3 extension pieces included and each of those is 8 inches long.
view full answer...

Powered A-Frame Trailer Jack for a 2008 Aerolite Trailer and Towing Mirrors for a 2003 Dodge Ram
The Husky Brute, # HT87247, would be a fine choice for your trailer. The Brute jacks are designed with an automatic stop to prevent over extension and damage of the jack. The 4,500 pound capacity is more than enough for the gross trailer weight of your Aerolite. And the mounting pattern is standard for A-frames. You will just need to make sure the hole for the jack leg is 2-1/4 inches for this jack to fit through. We also offer this same model with a wireless remote, # HT87641. For custom
view full answer...

Does the Jack Motor of the Stromberg Carlson have to be Orientated Forward
Theres really no reason why you could not install the Stromberg Carlson Electric A-Frame Tongue Jack # JET-2500 in any orientation on your trailer as you would need as long as it does not interfere with anything. You will want to have the jack itself as a whole orientated. I would not recommend you attempt to rotate the gearbox case as that would not be necessary.
view full answer...

How To Manually Operate Jammed Electric Trailer Tongue Jack
It is likely that the interior gears have stripped when the jack over-extended. If you have the manual crank that should have came with the jack, use it by removing the rubber plug at the top of the jack, insert the crank and fit it to the override nut. Turn handle counter-clockwise to lower the trailer. If you no longer have the crank, we sell a replacement as part # JCH-1. If manually cranking the jack is unsuccessful, you will probably need to replace the jack, as the jack manufactur
view full answer...

How to Remove the Snap-Ring on the Bulldog Round Snap-Ring Swivel Jack # BD151101
To remove the snap ring from the Bulldog Round, Snap-Ring Swivel Jack, # BD151101, you will need snap-ring or retaining ring pliers. These pliers are available at most local hardware and auto parts stores. The snap ring pliers will have two pins on the end that will fit in the holes of the snap ring on jack. When you squeeze the pliers, the ring will open up enough to be removed. To replace the snap-ring, you will simply use the snap ring pliers to open the ring enough to fit it back into
view full answer...

What is the Bolt Hole Size of the Dutton-Lainson Bolt-On Trailer Jack # DL22320
The diameter of the bolt holes on the mounting bracket for the Dutton-Lainson Bolt-On Trailer Jack, # DL22320, is 7/16 of an inch. This jack includes the bolts and additional brackets needed to mount this jack on the trailer frame, so you will not need to provide your own hardware.
view full answer...

Stabilizer Jacks for the Front of an Enclosed Toy Hauler Trailer
The stabilizer jacks, # JB-20, are made to help support slide-outs on travel trailers and would not be the best option for your application. What I recommend is a pair of scissor jacks like # UF48-979031, one on each side of the trailer frame. You can actually use a power drill with the correct socket to raise and lower the legs to make it easier and faster. I assume that you have one in the trailer since it is hauling a drag car and all. You could use bit # UF48-979005.
view full answer...

Powered Trailer Jack Fuse Keeps Blowing on Stromberg Carlson Trailer Jack # JET-3500
It sounds like there is a short somewhere in the wiring on the trailer. Something may be switched like the positive/negative or there is some bare metal on a wire that is touching the trailer frame. The fuse blowing indicates a short or something drawing too much power constantly. You will want to go through the trailer wiring and make sure its all set up correctly, there are no broken wires touching bare metal, and that all the grounds are attached to clean and corrosion free bare metal surface
view full answer...

Will a Bulldog Powered A-Frame Trailer Jack Fit a 2013-2014 Heartland North Trailer Travel Trailer
To determine if the Bulldog powered A-frame trailer jack # BD500185 will fit your North Trailer 32buds, you will need to measure from the center of the jack hole opening back to that storage cover on the tongue. If it is more than 4 inches then the jack will fit. Any more than less inches and it will interfere with that cover on the tongue. The mounting pattern for the bolts will be the same as the manual jack on the trailer now.
view full answer...

Will Ultra-Fab Power Twin II Manual Stabilizer Fit a 2003 Keystone Cougar 5th Wheel Trailer
The frame width on your 2003 Keystone Cougar 5th wheel trailer will need to be between 48 and 80 inches (measured from the outside of the frame on one side to the outside of the frame on the other side) in order for the Ultra-Fab Power Twin II Manual Stabilizer, # UF39-941704, to fit. The stabilizer has L-shaped brackets that fit on the frame and will be bolted into place. It is a straight forward installation and the average do-it-yourselfer should have no problem performing the installation
view full answer...

Would the Ultra-Fab Electric Landing Gear # UF17-943010 Fit a 2006 Forest River Cardinal 33LE
Yes, the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010 that you referenced would work well for your 2006 Forest River Cardinal 33LE. I checked the dry weight of your trailer and this jack set should have plenty of capacity. To install this you will need to Weld hangers to front of trailer frame, beneath overhang Bolt jacks to hangers Mount switches anywhere on trailer for easy access
view full answer...

Trailer Jack Recommendation for a Bandit Chipper with a Square Pipe Mount
We have two Bulldog jacks that use the square pipe mount attachment. We have the Topwind Swivel Jack, # BD195312, and the Sidewind Swivel Jack, # BD195362. Both of these jacks have a 15 inch lift, a 3,000 lb lift capacity and a 5,000 lb static weight capacity. For these jacks to fit on your chipper, the square pipe mount on your chipper must measure 2 inches x 2 inches. You should also note the retracted and extended heights of the jacks to make sure they will not be too short or too long for
view full answer...

Swivel Jack Recommendation for a Bot Trailer with a 3000 lb to 5000 lb Weight Capacity
We have a number of jacks that fall within the 3,000 lb to 5,000 lb capacities, however, the only jack that we carry that is similar to the Pro Series, Snap-Ring Swivel Jack, # PS1401020303, is the Bulldog Round, Snap-Ring Swivel Jack, # BD171401. This jack has a 10 inch lift and a 5,000 lb weight capacity. If you did not want to go with the Bulldog jack, we offer pipe-mount jacks like the Pro Series Round, Pipe-Mount Swivel Jack, # PS1401420303. The inner pipe mount of this jack must be wel
view full answer...

Recommendation for Electric Trailer Jacks on a 48 Foot MTI Gooseneck Race Car Trailer
We have two options that would work for your MTI 48ft. gooseneck trailer. Option #1: Ultra-Fab Products Trailer Jack -# UF17-943010 - with this option it has a combined weight capacity of 12,000 pounds, which will currently hold your trailer and race car providing that the weight at the front of the trailer does not exceed the 12,000 pound recommendation. If you decide to add more weight in the future, you will want to re-look at your jack situation. This item has a 3 year warranty.
view full answer...

Is the 2,500 Pound Capacity MaxxTow Electric A-Frame Trailer Jack Enough for 690 lbs Tongue Weight
The 2,500 pound capacity of the MaxxTow jack # MT70146 will be more than enough for your 2007 Coachmen trailer with its 690 pounds of tongue weight. I have included a link to a video review of this jack for you.
view full answer...

Is the Mounting Hardware Included with the Domar Stabilizer Jack # TJ01RT
The Domar Stabilizer Jack, # TJ01RT, does not include the installation hardware. This jack can be welded or bolted to the trailer frame. Having the jack welded to the trailer frame by a qualified professional would be the best option, but bolting the jack to your trailer will work as well. The bolt holes on this jack are 7/16 inches in diameter and 3 inches apart on center. I recommend using grade 5 or grade 8 bolts for the strongest possible connection. These can be found at most local hard
view full answer...

Will the Husky Brute Powered A-Frame Trailer Jack Fit a 2013 Keystone Bullet 23 BHS
As far as the mounting hole pattern, the Husky Brute, # HT87247, has the standard pattern that most all A-frame trailer jacks use so that should not be a problem. You will have to make sure the hole diameter for the jack is at least 2-1/4 inches. This is one of the most slim jacks at the top that we offer so if there are tanks or storage areas on the frame behind the jack it should not be a problem with the Brute installed.
view full answer...

Replacement Jack Tube and Wheel for a Bulldog Heavy-Duty, Rack-and-Gear Jack # BD165411
Yes, we do actually. You will want a Bulldog Heavy-Duty, Rack-and-Post Assembly w/ Wheel # BD019060 to replace the zinc-plated post and wheel of the Bulldog Heavy-Duty, Rack-and-Gear Jack with Steel Wheel # BD165411.
view full answer...

Diameter of the Outer Tube of the MaxxTow Electric Trailer Jack # MT70146
I spoke to my contact at MaxxTow and he informed me that the outer dimension of the outer tube of the jack is 2-1/8 inches.
view full answer...

Installation of Stromberg Carlson Electric A-Frame Trailer Tongue Jack, Part # JET-2500
Installation of the Stromberg Carlson Electric A-Frame Tongue Jack, Part # JET-2500, should be completed by following all of the manufacturer instructions. You should install the jack using all three supplied star washers, bolts and nuts. The washers should be placed on the bolts first; they will dig through the paint on the top surface of the jack mounting plate to provide the essential solid ground connection between the jack and trailer frame. The nuts should be installed on the bolts eve
view full answer...

How to Wire the Motor and Switch for Stromberg Carlson Electric Landing Gear LG-1
The shorter, fused wire on the switch should be pink and the longer wire should be the true red wire. To connect the switch for the # LG-1 Stromberg Carlson landing gear motor, you will connect the longer black and red wires from the switch to the matching wires on the motor. The pink fused wire will be run to the trailer battery for 12V power on the positive terminal, and the shorter black wire will be grounded to the negative battery terminal. It is a little confusing since the switch has
view full answer...

Electric Jack Recommendation to Replace a Jack with a 2 inch Outer Diameter
The Bulldog Powered-Drive Trailer Jack # BD500187 has an outer tube diameter of 2-1/4 inches and an inner tube diameter of 2-1/16 inches. This jack should be able to work on your trailer but it really depends on the diameter of the hole in your coupler. If it is larger than 2-1/4 inches then the jack will install. If the hole is smaller than that you may have to enlarge the hole to install the # BD500187. Or, if you can get by with a lower capacity you could use a Stromberg Carlson Electri
view full answer...

A-Frame mount Electric Trailer Jack for a 10K Race Car Trailer
Toy haulers like your race car trailer often times have a higher tongue weight than the traditional 10 to 15 percent of the gross trailer weight. The higher capacity you go with, the easier it will be for the jack to lift the load and the longer it will last. You could get a Husky 4,500 pound capacity jack # HT87247 at a good price. The available 4k capacity jacks actually cost a little more. If you measure the tongue weight of the trailer, when loaded and ready to tow, and it ends up bei
view full answer...

What is the Inner Tube Outer Diameter of the Pro Series Jack part # PS1401140303
I went out into our warehouse and measured Pro Series Round, Snap-Ring Swivel Jack # PS1401140303 and found that the outer diameter of the inner tube is 2 inches and the outer diameter of the outer tube is 2-1/4 inches. Based on that this jack should work well for you.
view full answer...

Clearance to Propane Tank Cover on Keystone Trailer of Control Housing on Bulldog Lift # BD500185
The rear of the control unit housing on the Bulldog Powered-Drive Trailer Jack, part # BD500185, extends 4 inches behind the center line of the main down tube. On your trailer frame simply measure 4 inches back from the center point of where the round mounting bracket will attach to your trailer frame to determine where the back of the housing will be when installed. Please refer to the included photo.
view full answer...

How does the Bulldog Sidewind Jack # BD150415 Swivel
The Bulldog Sidewind Jack, # BD150415, requires the 2 inch pipe, # BD015279, to swivel. The pipe has 4 holes that are compatible with the 4 holes on the pipe extension on the jack and swivels from the towing position to lifting position with the included pin. I made a short video showing how this jack swivels for you.
view full answer...

How does the Bulldog Jack # BD1541150301 Swivel
The Bulldog Jack, # BD1541150301, swivels on a metal tube, # BD015279, that will need to be welded to your trailer frame. I made a short video showing how this jack swivels for you.
view full answer...

How to Wire the Stromberg-Carlson Electric A-Frame Tongue Jack, # JET-3500, to a Trailer Battery
The red power wire on the Electric A-Frame Tongue Jack, # JET-3500, is the power wire and it will attach to the positive battery terminal on your trailer battery. First, remove the fuse in the in-line fuse holder on the red wire. Mount the jack to the trailer and tighten it down. The jack grounds through the mounting hardware. Then connect the red wire to the positive battery terminal. The last step is to insert the fuse in the fuse holder.
view full answer...

Stromberg Carlson Landing Gear # LG-1 for Jayco Qwest Fifth Wheel Camper
The Stromberg Carlson # LG-1 is an industry-standard landing gear that should fit on your fifth wheel with no problems. The mounting brackets weld directly to the frame of your fifth wheel, and the jacks would then mount into the brackets. As long as your Jayco Qwest has exposed frame members under the trailer loft for the brackets to weld to, the LG-1 will work great for you. I have linked you to a copy of our return policy.
view full answer...

Can Pro Series Square Trailer Jack PS1401010376 be Paired With Another Jack
The Pro Series Square Jack, # PS1401010376, can work in tandem with another jack but it was not designed to have a mate that has a pin facing out opposite if # PS1401010376. What you can do is use # PS1400990376, which has the pin at the front. You would need to provide your own connection between the two jacks.
view full answer...

Distance Between Welded Stops for Clamp Hangers on the Bulldog Landing Gear Set # BD500170
The distance between the bottom of the lower welded stop to the top of the upper welded stop on the Bulldog 7,000 lb Landing Gear Set, # BD500170, is 17-1/2 inches This means that the distance from the bottom of the upper clamp welded to your trailer frame to the top of the lower clamp must be 17-1/2 inches (see photo). I went out to our warehouse and measured all of our fifth wheel landing gear sets and we do not have a set that measures 18-1/2 inches from the top of the upper welded s
view full answer...

Replacement Jack Recommendation for Shamrock Forest River 2000
The Atwood Trailer Jack # 273800 that you referenced should work as a replacement jack for your Forest River 2000 because it has a 5,000 lb capacity and can be welded or bolted on.
view full answer...

Husky Trailer Jack Stopped Working Even After Replacing Trailer Battery
The first thing I would check is the wiring to the jack, Check for corrosion, loose or broken wires. You will want to take a close look at the ground connection too. If there are any wires with nicks in the wires and they are touching bare metal, it can be causing a short. A short could cause the fuse or circuit breaker on the jack to trip and that may be the click you are hearing. If the jack is an older model and it was over extended then it could potentially be damaged. The newer versions
view full answer...

Where Does the In Line Fuse Holder Get Installed on Ultra-Fab Electric A-Frame Trailer Jack
On the Ultra-Fab trailer jack # UF38-944017 the in line fuse holder will be cut in half and spliced in along the power wire. Ultra-Fab makes the following statement: The Fuse Holder can be installed by means of either crimping or soldering the connections. For convenience the Fuse Holder should be installed near the power source. Cut red wire in half, connect one end to the end of the black wire from the jack and connect the other end of the red wire to the positive post of the battery.
view full answer...

Will Ultra-Fab Deluxe Electric Landing Gear, # UF17-943010, Fit a 2003 Keystone Challenger
The Ultra-Fab Deluxe Electric Landing Gear, # UF17-943010, has brackets that are designed to be welded to the vertical part of a 5th wheel trailer frame beneath the overhang. This makes it a universal type of application and should work well for your 2003 Keystone Challenger. You just have to inspect the trailer for the best place to weld the brackets.
view full answer...

Which is Better, a Side Wind Trailer Jack or a Top Wind Trailer Jack
You would choose a side wind or top wind jack based on several factors. Each has its advantages. If clearance is an issue for the radius of a top wind, then you would choose a side wind. The opposite is also true. It is my experience that a side winding jack is easier to turn. However, if the tongue is low to the ground a top wind would be a better option because you would not have to bend down as much and it would not be as awkward to turn. A side winding jack normally has inner components t
view full answer...

How Far Past Edge of Trailer Will Crank Stems of Husky Crossframe Stabilizer Jack # 76856 Extend
The mounting flanges of the Crossframe Mount Stabilizer Jack are width adjustable from 64-74 inches apart. The flanges serve as the attachment point to the travel trailer frame. Once installed, the crank stems will extend about 8 inches to either side of the attachment point at the frame member. If you measure the distance from the outside of the frame member to the outside edge of the trailer, you should have a pretty good idea how far if at all the stems will extend past the side of the tra
view full answer...

Which A-Frame, Top Wind Trailer Jack is Shortest from Mounting Bracket to Top of Jack
The A-frame, top wind jack that has the shortest distance is going to be the Bulldog jack you referenced, # BD155032. From the mounting bracket to the top is a little over 10 inches (10.2). Another possible solution is to use a longer ball mount to move the trailer further back so the tail gate can lower without hitting the jack. We have some very long ball mounts, see link, some of which have a distance of 16 inches from the center of the hitch pin hole to the center of the ball hole.
view full answer...

Height of Bulldog and the Powered-Drive Trailer Jack, # BD500187, from Bracket to Top of Jack
I spoke with my contact at Bulldog and the Powered-Drive Trailer Jack, # BD500187, measures 20-1/2 inches from the mounting bracket to the top of the jack. I have included a picture showing this measurement for you.
view full answer...

What is the Capacity of Ultra-Fab 5th Wheel King Pin Tripod Stabilizer # UF19-950001
The support capacity of the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer, # UF19-950001, is 5,000 pounds, just like you have said. As long as the pin weight of your trailer does not exceed 5,000 pounds at any given time it is resting on the tripod then it will work well for you. With that said you do not want to suddenly drop 5,000 pounds on it. It should be lowered onto the tripod gradually. If you need additional length beyond the 42 to 56 inches this tripod has, you can add extension le
view full answer...

Is the Atwood Deluxe Power Trailer Jack Waterproof
In order for something to be considered waterproof it needs to be able to be submerged underwater for a length of time without allowing any water to seep in. The Atwood Deluxe Power Trailer Jack # 80515 that you referenced is considered weather proof and under normal circumstances would not get damaged by rain. If this was going on a boat trailer you would not want to submerge the jack during launching.
view full answer...

Fulton F2 Swing Up Jack # F1413040134 for 2x3 Inch Trailer Frame
The problem with trying to mount the Fulton F2 # F1413040134 on a 2x3 trailer frame is that the u-bolts do not have enough threads on them to draw the jack tight. If you can locate the appropriate u-bolts, you can by all means use them. You would need a u-bolt with a 3-1/2 inch span, center to center with legs no longer than 3 inches. Your best bet would be a weld-on model like # F1413060334.
view full answer...

Looking for Swivel Trailer Jack with Overall Length of 15 Inches or Less
The closest I can come to the measurement you mention is the Pro Series Pipe Mount Swivel Jack, part # PS1401060303. The total height of the jack when fully retracted is 16-5/8 inches tall, measured from the bottom of the foot plate to the top of the bracket where the handle assembly where the handle attaches to the jack tube itself. The center of the mounting pipe to the bottom of the foot plate measures 11-3/16 inches. This jack is a weld-on application, and you can see these dimensions by ref
view full answer...

Installation and Wiring of a MaxxTow Electric Trailer Jack on a 2012 Forest River Wildwood Trailer
The MaxxTow Electric Trailer Jack # MT70146 that you referenced has a lifting capacity of 2,500 lbs. That should be plenty for your 2012 Forest River Wildwood travel trailer. It will install in the same place as your current jack. You can either have it welded on by a qualified welder or bolt it on. You will need to provide your own hardware. If your current jack is bolted on you could most likely just reuse those bolts. You will have to remove your current manual jack, but the # MT70146 come
view full answer...

How Far Does the handle Stick out on Bulldog Trailer Jack # BD195369
I suppose that since you are using this jack but are asking for the measurement that you do not actually have the jack present. So I will be happy to help you. There is a little bit of play in the handle but when measuring from the side of the jack out to the end of the handle it will be at least 4-5/8 inches and at most 4-7/8 inches. I made a picture showing the measurement for you.
view full answer...

Replacement Handle or Handle Grip for a Fulton Pro Series PSEJ10000101 Trailer Jack
I spoke with my contact at Fulton and Pro Series and got some information for you. A lot depends on the age of the jack. If the handle is held in place by an e-clip and not a pin then there are no replacement parts available. If the handle is held in with a pin in the top gear then you would need to replace the entire handle assembly using # F0933301S00 which is a different handle design but would fit. The black handle grip on your jack is not available as a separate part.
view full answer...

Replacement Wheel For a Bulldog Rack and Gear Trailer Jack
If the jack model is 165311 (our Bulldog # BD165311) then you will need the rack and post assembly with the steel wheel attached that you have referenced, # BD018006. The wheel by itself for this style jack is not available unless the inner diameter of the jack is 1-1/4 inches, then you could use # BD018507. If the wheel is not meant to come out (if you will have to drill to remove it) then you would need to replace the entire rack and post assembly with # BD018006.
view full answer...

Installing PS1400800383
The Pro Series Square Topwind Jack with Footplate and Drop Leg, part # PS1400800383, has an overall height when fully retracted and with the drop leg fully inserted, of 22-7/8 inches. You can select an appropriate mounting height for welding the jack to your trailer frame based on having adequate clearance between the bottom of the footplate and the ground when under a typical load. My contact at ProSeries confirms that the outer tube on this jack is designed to be strong enough to allow fle
view full answer...

What is the Overall Height from Mounting Bracket to Top of Husky Brute Jack, Part # HT87248
The round mounting plate on the Husky Brute Electric Trailer Jack, part # HT87248, is 22-1/4 inches below the top of the motor housing. Please refer to the included photo with measurement.
view full answer...

Can a Gooseneck Trailer Stabilizer Jack be Used on a 5th Wheel Trailer with an Adapter Installed
It sounds like you have the Anderson Ultimate connection # AM3225 or # AM3200. In either case since the adapter part that fits on the king pin can easily be removed I recommend going with a 5th wheel stabilizer, see link. You could use the gooseneck type and keep the adapter on but it is just one more link in the chain instead of a direct connection between the king pin and the stabilizer which would be more ideal.
view full answer...

How Does the Ultra-Fab Rear Electric Stabilizer for Trailers and RVs Install on a Trailer Frame
The first thing you will want to do is measure the frame on your trailer to determine fit of the Ultra-Fab Rear Electric Stabilizer, # UF39-941602. It will fit on frames that measure 66-5/8 inches to 69-5/8 inches wide. It bolts to the bottom of the frame and with the proper tools, an assistant, and some grade 5 or better hardware you should be able to install this yourself. The remote is actually no longer available. The panel which is included can be installed anywhere that is convenient fo
view full answer...

What Replacement Parts Available for Stromberg-Carlson Electric A-Frame Jack, Part # JET-3500
We do offer some replacement parts for the Stromberg-Carlson Electric Tongue Jack, part # JET-3500, however these are limited to extend/retract switches, light switches, LED light components and plastic housings. Based on your description it sounds like the only user-serviceable item we offer that might address the wiring issue you have is the replacement extend/retract switch, part # 7145-226023. My manufacturer contact confirms that no motor or internal mechanical replacement parts, such as
view full answer...

How to Determine What Brand of Landing Gear on 1998 Fleetwood Mallard and Can Gear Box Be Replaced
Usually, you can find the brand and model information directly on top of the jack or landing gear, or sometimes it is near the bottom of the outer tube. A third place to check would be the the housing that covers the gears. If you cannot find it in any of these places, it may be in the owners manual literature. To determine if you can just replace the inner parts and use your existing jack, you will want to inspect the whole jack to make sure everything is structurally sound. Replacing the
view full answer...

Replacing Venture Motor on Atwood Gear Box on Powered Landing Gear
If your motor runs but the landing gear does not move (except when manually cranked) this suggests that the gearbox in the landing gear is still functioning properly but that there is some issue preventing the motor torque from reaching the gearbox. First I suggest you unbolt the motor from the landing gear. Check the motor drive shaft; it is possible that it has been sheared off. If the motor were to remain on after the landing gear legs are fully retracted or fully extended all the force fr
view full answer...

Is Fastway Power Trailer Jack Flip-Foot Compatible with Stromberg-Carlson Electric Jack, # JET-3500
Although the tube diameters of these two power jacks are similar, 2-1/4 and 2-3/16 inches, we do not recommend trying to adapt the flip-foot mechanism from the Fastway Power Trailer Jack to the Stromberg-Carlson # JET-3500. These parts are not intended for use with one another, so for safety considerations we cannot recommend that any of their components be mixed. My contact at Stromberg-Carlson confirms that a folding foot mechanism is neither available nor planned for use with the JET-3500.
view full answer...

Does the Ultra-Fab Ultra Scissor Jacks # UF48-979031 Have a Lift Capacity
The Ultra-Fab Ultra Scissor Jacks, part # UF48-979031, are stabilizer jacks which are designed to be attached to the frame of your trailer or RV and crank down to stabilize a portion of the trailers weight. It has a support weight capacity of 6,500 lbs. This stabilizer jack does not have a lift capacity rating because is not designed to do any lifting of your trailer, plus you do not want to lift or level a trailer or RV because you can cause damage to it. A trailer frame is not intended to c
view full answer...

What are the Dimensions of the Stromberg Carlson Electric A-Frame Tongue Jack # JET-2500
I have provided a picture that shows the jack dimensions. These measurements were taken here by another Expert recently. The outer tube is 2 inches in diameter and the inner tube is 1-3/4 inches in diameter. The bracket to mount the jack uses a standard A-frame pattern.
view full answer...

Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch by 2-1/2 Inch Trailer Tongue
Yes, the Pro Series Round Snap-Ring Jack, # PS1400300303, will bolt around your 2 inch by 2-1/2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer. I have attached a photo showing the bolt hole dimensions of this jack for you to check out.
view full answer...

How Does the Ultra-Fab Power Twin II Electric Stabilizer Install on a Trailer
You will need to bolt on the Ultra-Fab Power Twin II Electric Stabilizer, # UF39-941705, using the included hardware. It bolts to the bottom of the frame on the travel trailer. You CAN do it. I believe in you. If you have the proper tools (drill, bits, wrenches) you can install this yourself at home. If you are not familiar with projects like this or have any reservations about performing the installation I do recommend having a professional install it. RV dealerships with service centers or
view full answer...

Can I Replace Just One Jack on 2012 PJ Flatbed Trailer With Bulldog 2-Speed Jack, Part # BD183816
In order for your existing single-speed trailer jack to work with the Bulldog 2-Speed Jack - Drop Leg w/ Spring Return, part # BD183816, it is essential that the existing jack have a cranking ratio (the number of handle turns that moves the jack one inch) that is the same as the 9-turns-per-inch high gear ratio of the Bulldog. If the two jacks do not have the same turns ratio, then the trailer will elevate unevenly, creating a safety hazard. My contact at Bulldog tells me that if the OEM jack
view full answer...

Ultra Fab Power Twin II Electric Stabilizer Jack Recommendation for a 2008 Montego Bat KZ 5th Wheel
I did some research on your 2008 Montego Bay by KZ and found that it weighs around 12,000 lbs unloaded. Due to this weight and the location of where the stabilizer jacks would install I would recommend you go with 6,000 lb Ultra-Fab Power Twin II Electric Stabilizer # UF39-941705. This product comes with the necessary hardware to bolt to the frame of your vehicle.
view full answer...

Electric A-Frame Mount Trailer Jack for a 2013 Winnebago Minnie 2201DS
It looks like the gross trailer weight of the 2013 Winnebago Minnie 2201DS is in the neighborhood of 5,500 pounds. This should put the tongue weight around 550 to 825 pounds (10 to 15 percent of gross trailer weight). Any of the electric A-frame mount trailer jacks we carry are going to have the capacity needed for this trailer. The issue is going to be with the storage box that is directly behind the jack mounting location. This may cause some interference issues. You also need one that has
view full answer...

Mounting Option for the Shelby Sidewind Drop Leg Jack # 6108SW
The Shelby Sidewind Drop Leg Jack, # 6108SW, is a weld-on style jack that does not include any mounting hardware. This jack was designed to weld directly to the trailer frame along the outer tube (see photos). If you want a bolt-on style jack, I would recommend the Fulton Square Drop Leg Jack, # FHD2500. This jack will bolt around a trailer frames up to 3 inches wide by 5 inches tall. I have attached a review video of this jack for you to check out.
view full answer...

Dimensions of Mounting Holes for Stromberg Carlson Scissor Jack # JSC-24-IND
To determine the measurements you were looking for, I went into our warehouse and measured the Stromberg Carlson Scissor Jack # JSC-24-IND. The diameter of the small, circular holes on the outer edge are 5/8 inches. The size of the larger, rectangular holes are 7/16 inches wide by 3/4 inches long. I have provided a graphic showing all the dimensions.
view full answer...

How do the Ultra-Fab Stabilizer Jack Attach to RVs
The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs # UF39-941704 that you referenced is designed to be bolted on with the included mounting hardware. The difference between the # UF39-941704 and the # UF39-941705 is that the # UF39-941705 comes with dual 12 volt motors to raise and lower the legs of the stabilizer jacks. Whereas, the # UF39-941704 that you referenced require manual operation that includes cranking a jack handle.
view full answer...

Trailer Dolly Recommendation for Moving a Boat Trailer in and out of a Garage
The Fulton F2 Swing-Up Trailer Jack # F1413020134 that you referenced would certainly be capable of moving your trailer around as long as the tongue weight of your trailer does not exceed the 1,600 lb capacity of the jack. However, it would not be nearly as easy as using a Trailer Valet Swivel Jack and Trailer Mover # STC-V211. I believe I have something that would be ideal for you. Since you are looking for an easy way to move your trailer in and out of your garage I think you might also be
view full answer...

Stromberg Carlson JET-2500 Jack for Coachman Cascade Travel Trailer
The Stromberg Carlson # JET-2500 Electric Trailer Jack you referenced has a lift capacity of 2500 lbs. The jack will work just great for trailers with tongue weights less than 2500 lbs, the tongue weight of your Coachmen Cascade should certainly be less than that. I have edited a photo for you showing the various dimensions and clearances related to the jack. The dimensions I provided should let you know if you will have clearance for your propane tanks.
view full answer...

Footplate and Caster Availability for Bulldog Fixed-Leg Trailer Jack # BD195321
We do have a drop leg with a foot plate available for the Bulldog Fixed-Leg Trailer Jack # BD195321, but casters are not currently available for jacks with square tubes. I recommend the Bulldog 17-11/16-Inch Drop Leg With Pin # BDDF3500 to go with the trailer jack you mentioned. It has a footplate width of 7-1/2 inches and a tubing width of 1-7/8 inches and includes the pin. To avoid the cost of buying the jack and drop leg separately, you might be interested in the Bulldog Drop Leg Trailer J
view full answer...

Dimensions of Bulldog Trailer Jack # BD1700100301
I ran out to our warehouse and pulled one of the Bulldog # BD1700100301 jacks off the shelf. I measured the retracted height of the jack at 21-5/16 inches, and found the outer tube to be 2-1/4 inches in diameter. I edited a photo showing these and other relevant dimensions for you.
view full answer...

Replacement King Pin Cup for Ultra-Fab Economy 5th Wheel Tripod Stabilizer, part # UF19-950500
UltraFab does offer a replacement King Pin Cup for their Economy 5th Wheel King Pin Tripod Stabilizer, part # UF19-950500. The replacement King Pin Cup part consists of the cup and threaded post, which are one assembly. This product is on our website and the part number is # UF19-001081.
view full answer...

Does the Atwood Deluxe Power Trailer Jack Come with a Manual Jack Handle
Yes, a manual handle does come with the Atwood Deluxe Power Trailer Jack # 80515. We also sell the handle as a replacement part. Check out part # 87891 to see what the handle looks like.
view full answer...

Jack Recommendations for a Trailer with a 5 inch by 3 inch Frame
I do have a couple jack options for you, but the Fulton F2 Swing Up Jack # F1413130334 that you referenced will not work on your 5 inch by 2 inch trailer frame. The jack you referenced will work on trailer frames that are 4 inches tall by 5 inches in width. For the same jack with the only difference being that it welds on instead of bolts on I would recommend the Fulton F2 Swing-Up # F1413050334. Another option you have would be to get a Fulton Bolt-Thru Swivel Marine Jack # FXP15. This jack
view full answer...

Will Bulldog 10k Electric Landing Gear Fit a Crossroads Cross Terrain Trailer
Bulldog makes a high quality and sturdy set of landing gear. I recently had the 12K model out of the box to check on the legs for a different customer and it is a solid set. To determine if the 10K set, # BD500161, is going to work for you take a look at the bracket height and lift specs. When retracted the bracket height is 29-13/32 inches and when extended 65-3/16 inches. You get a total lift amount of 36 inches. The drop leg makes up 18 inches and the other 18 inches is from the actual pow
view full answer...

Can I paint the Primed Wheel on Bulldog Rack-and-Gear Jack with Steel Wheel, Part # BD165311
I spoke to my contact at Bulldog about this product and the primed finish on the wheel and swivel bracket. These parts can be spray painted. Bulldog suggests using a premium-quality spray paint, and a black gloss finish is fine. It is advisable to first thoroughly clean the parts to be painted, even if the jack has not yet been used. (It is possible that there could be a light coating of a protective lubricant on the jack and this will need to be completely removed to allow proper adhesion of
view full answer...

How to Determine if There is Enough Clearance to Install an Atwood Powered Jack on a Jayco X23B
You will need to do some measuring to determine if the Atwood Power Trailer Jack # AT80718 will fit on your trailer. I would recommend you lower the front bed and measure the distance between the top of the frame of the trailer to where you think it would interfere, if this distance is more than 25-3/4 inches you will be fine. The reason is because the distance from the mounting plate to the top of the jack is 25-3/4 inches. So if the measurement you took is more than that you should be fine
view full answer...

Outer Tube Wall Thickness of Pro Series 8,000 lb Jack # PS1400800383
I pulled one of the Pro Series # PS1400800383 jacks off the shelf for you, and disassembled it in order to get an accurate measurement of the outer jack tube. I found that the wall thickness of the outer tube was .108, or about 7/64 of an inch.
view full answer...

How to Choose the Correct Jack for a Small Utility Trailer
When choosing a jack for your trailer you will want to choose a jack that has enough lift to lift the coupler over the hitch ball on the tow vehicle. I would recommend hooking your trailer to your truck and, with additional help, lift the trailer coupler a few inches above the hitch ball. With the trailer tongue lifted, find an appropriate location for the jack on your trailer tongue and measure from the center of the frame to the ground. This will tell you the approximate extended height that y
view full answer...

Replacement Motor for Ultra-Fab Rear Electric Stabilizer for Trailers and RVs # UF39-941602
We do offer the motor for Ultra-Fab stabilizer jack # UF39-941602. You will need Replacement Motor for Ultra-Fab Rear Electric Stabilizer, # UF39-842001. The cost between the motor and the complete jack is only slightly different so you may want to consider just replacing the jack with the complete unit # UF39-941602 so you will get all new parts.
view full answer...

Fulton Snap-Ring Jack Recommendation
The Fulton Round, Snap-Ring Swivel Marine Jack # FTJ120W0301 that you referenced would be a good choice for you. The zinc coating helps prevent corrosion also. This jack has a 1,200 lb lifting capacity. You will need to be sure that is enough capacity to lift the tongue of your trailer. The # FTJ120W0301 is designed tor snap ring pilot holes with a 2.3 inch diameter. So if you measure the one that is on your trailer and it would be compatible this would bolt right up. Or you could weld on
view full answer...

Will the Ultra-Fab Power Twin II Electric Stabilizer Fit a 2013 Coachman Freedom Express 281RLDS
The Ultra-Fab Power Twin II Electric Stabilizer, # UF39-941705, is designed to fit trailers and RVs with frames measuring 48 to 80 inches wide (measured from outside to outside). The brackets that attach to the frame are 36 inches long so there will need to be space on the frame at least this long for the brackets to fit. You will need to measure to determine if this unit will fit your 2013 Coachman Freedom Express 281RLDS.
view full answer...

Swivel Trailer Jack with a Wheel for an RC Enclosed V-Nose Enclosed Utility Trailer 2 x 3 Frame
With a 2 by 3 inch frame we will not have a bolt on option but I recommend going with a weld-on swivel jack instead. You could use # F1413060334. The welding should be done by a qualified professional welder. This jack has a lift height of 10 inches and the bracket can be adjusted up and down 8 inches to best fit your application. The jack has a capacity of 1,600 pounds which is good for most enclosed trailer applications like yours that can hold a couple of motorcycles or a 4-wheeler. C
view full answer...

Sidewind Jacks Versus Topwind Jacks
There really is not an advantage to having a side-wind jack versus a top-wind jack. It really just comes down to personal preference and what clearances are available on the trailer. You may find that the handle location would interfere with components mounted on your trailer with one style, but not for the other. In theory you would need to bend over farther to operate a sidewind jack since the jack handle goes up and down. Depending on the height of your trailer this may not be an issue for
view full answer...

What Size are the Mounting Holes for the Domar Stabilizer Jack
I went out to the warehouse and pulled the Domar stabilizer jack, # tj01rt, to take the measurements of the mounting holes. The diameter of the mounting holes is 7/16 inches. The mounting holes are 3 inches apart on center. I have made a short video showing how I took the measurements for your viewing pleasure.
view full answer...

Extended and Retracted Length of 2k BullDog Swivel Trailer Jack and Does the Inner Tube Spin
I went out to the warehouse and pulled the Bulldog Swivel Trailer Jack # BD1541150301. When fully retracted it measure 7-3/4 inches from the bottom of the inner tube to the center of the mounting bracket. When fully retracted it measures approximately 18 inches. The inner tube does spin so you can use wheel # BDCP555. If you are turning the handle and the wheel is spinning the jack will not go up or down so you will have to prevent the wheel from spinning in those scenarios. I have include a
view full answer...

Will 10K Bulldog Electric 5th Wheel Landing Gear Set Fit in Place of a 6.5K Set
I spoke with my contact at Bulldog and he informed me that the 6.5k, 7k, and 10k landing gear sets uses the same mounting brackets so you can switch out the one you have with a higher capacity. On the 10k the overall height of the entire unit will be 4 inches taller than the one you have. The motor is 7-5/8 inches tall overall.
view full answer...

Dimensions of the Outside Tube of the Pro Series Jack # PS1401500383
I went out into our warehouse and measured a Pro Series Square Jack with Footplate # PS1401500383 and found that the outside dimensions are 2-1/4 inches by 2-1/4 inches.
view full answer...

Are Replacement Pull Pins Available for Fulton F2 Swing-Up, Wide-Track Trailer Jack # F1413040134
We do sell a replacement for the pull pin on your Fulton F2 Swing-Up # F1413040134. It is the Replacement Pull Pin Kit # F500136, which fits the Fulton F2 series swing-up jacks. It includes a spring and retaining ring in addition to the replacement pull pin.
view full answer...

Overall Length Including Motor and Dimensions of the Bulldog Landing Gear Set # BD500170
I spoke with my contact at Bulldog and verified the overall length and dimensions of the Bulldog Landing Gear Set, # BD500170. The overall length of the jack is 37 inches when it is fully retracted and 73 inches when fully extended. The outer tubing of the jack is 2-1/2 inches square and the footplate measures 6 inches wide by 8 inches long. I have attached a photo showing these dimensions. If you need additional information on this assembly from what I have provided, then just let me know.
view full answer...

Order Tracking
Shipping Information
Contact Us
About Us

Help Videos and Articles
Search
Privacy Policy
Your Account Login