view cartView Cart

Shop by Vehicle


Filter Questions and Answers:


reset filter
Trailer Hitch
Trailer Hitch
 

Expert Answers about Trailer Hitch


  • Hitch Recommendation for a 2004 Volkswagen Golf to Tow Small Camper
  • The Curt Hitch part # C11066 that you referenced has been confirmed as a fit for your 2004 Volkswagen Golf GTI. The hitch itself has the towing capacities of 2,000 lbs trailer weight and 200 lbs tongue weight. As long as your trailer stays under this figure and the towing capacities that are listed for your vehicle in the owners manual you would be good to go. To complete your towing setup you may also be interested in purchasing the following: Draw-Tite Wiring # 119178KIT (installation...
    view full answer...

  • Trailer Hitch Recommendation for a 2005 Lexus GX470
  • For your 2005 Lexus GX470 we do have hitches available. The most popular one is the Hidden Hitch part # 70779. This is a Class III hitch with a 2 inch opening that has plenty of towing capacity. I attached an install video for you to check out for more info. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes...
    view full answer...

  • Trailer Hitch Recommendation for a 2012 Fiat 500
  • The Hidden Hitch part # 60289 that you referenced has been confirmed to fit your 2012 Fiat 500 POP. This has a 200 lb tongue weight rating and a 2,000 lb total trailer capacity so it should work very well for you as long as the owners manual of your vehicle says you can tow with your vehicle. I attached an install video for you to check out as well. While this does clamp around the bumper supports it would not prevent them from still functioning in the event of an accident. The brackets...
    view full answer...

  • Trailer Hitch Receiver and Wiring Recommendation for 2014 Nissan Frontier 4 x 4 Crew Cab
  • When it comes to a hitch for your 2014 Nissan Frontier 4 x 4 Crew Cab, I recommend going with the Curt Class III Trailer Hitch Receiver, # 13241. This hitch bolts directly to the frame of your Frontier and provides a towing capacity of 5,000 lbs and 500 lbs of tongue weight. I have attached an installation video for you. As for wiring, you will want to go with the T-One Vehicle Wiring Harness, # 118266. This harness provides the relays to activate the tow package along with the 7-way...
    view full answer...

  • Hitch Extender to Tow a Trailer with a 2005 GMC Sierra 2500 with Truck Bed Camper
  • First you will need to determine if the trailer hitch on your 2005 GMC Sierra 2500 is a 2 inch or 2-1/2 inch. Just measure the opening width to determine the size. I am assuming that the tailgate is down and/or the camper overhangs the back of the truck thus the need for an extension. I recommend an extension that is long enough to where the face of the receiver is flush with or a few inches recessed under the rear most part of the truck or camper, whichever extends out the furthest. If...
    view full answer...

  • Curt Hitch Recommendation for a 2015 Ford Transit
  • The correct hitch for a 2015 Ford Transit Connect is the part # C13167, the part # C13193 that you referenced is designed to the 2015 Fort Transit T150, T250, and T350. It sounds like you may have ordered the wrong hitch for the vehicle you have.
    view full answer...

  • Hitch Recommendation for a 2006 Chevy Cobalt
  • Based on the size of the food cart you have the only option I can recommend for you would be to install a hitch on your 2006 Chevy Cobalt like # 60808 or part # 60815 if you have an SS model and tow a small trailer. The dimensions of the food cart are too big to fit on a cargo carrier. The hitch I recommended comes with a ball mount and a pin and clip. For a ball you can use # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). You will need to check the coupler of the trailer...
    view full answer...

  • Hitch Recommendation for a 2007 Dodge Ram 1500
  • If Dodge says that the towing capacity for your 2007 Dodge Ram 1500 is 7,000 lbs then that is the heaviest trailer you can tow. A towing setup is only as strong as it's weakest component. If you were to install a hitch with a heavier capacity than what your vehicle has it would not allow you to tow a trailer above the capacity for the vehicle. If you can find a lighter trailer so that your setup weighs less than the capacity for your vehicle you could install the B and W Hitch part #...
    view full answer...

  • Hitch for 2014 Honda CR-V Capable of Carrying 3 or 4 Bikes
  • There are Class III hitches available for the 2014 Honda CR-V that have the 2 inch receiver opening, which would allow you to carry a 3 or 4 bike rack. There isn't a hitch with a larger receiver opening available for your CR-V. Of the available hitches, I'd recommend the Draw-Tite Class III hitch, part # 75742. You can see the install details and an install video by clicking the provided links. For a compatible bike rack, the Thule Hitching Post Pro, part # TH934XTR would be a high...
    view full answer...

  • Hitch Recommendation for a 2014 Ford Focus to Tow Small Trailer
  • We have everything you need so that your 2014 Ford Focus can tow a trailer. For a hitch I would recommend the Hidden Hitch part # 60290 as it has been confirmed to fit your vehicle and it includes a ball mount and pin and clip. I attached an install video for you to check as well. You will also need a hitch ball to complete the connection. For that you would want the part # 19256 for a 1-7/8 inch hitch ball or part # 19258 for a 2 inch hitch ball. For trailer wiring you would want...
    view full answer...

  • Trailer Hitch And Wiring Recommendation For 2011 Jeep Grand Cherokee
  • The Curt Trailer Hitch, part # C13065 is designed to fit your 2011 Jeep Grand Cherokee. This is a Class lll hitch and has a 2 inch receiver opening. I have attached a link to an installation video for this trailer hitch on a 2011 Grand Cherokee you can check out. The hitch is rated with a maximum trailer weight of 5,000 lbs and a maximum tongue weight of 500 lbs. You will want to check your owner's manual or with your dealership to make sure you do not exceed the towing or tongue weight...
    view full answer...

  • Hitch Recommendation for 2011 Jeep Grand Cherokee
  • Check out the Curt Hitch part # C13065. This hitch installs right up to the bottom of the rear fascia of your vehicle which will give it the best possible ground clearance. This is also a 2 inch hitch confirmed to fit your 2011 Jeep Grand Cherokee. When we installed this hitch on a similar 2011 Grand Cherokee as yours we found that there was a distance of 15 inches from the bottom of the hitch opening to the ground. If you plan on doing some towing you might be interested in etrailer...
    view full answer...

  • Hitch Recommendation for a 1993 Toyota Corolla Wagon
  • We have a hitch confirmed to fit your 1993 Toyota Corolla wagon, but the hitch # C11181 that you referenced is not the correct one. Instead you would want the part # C111283 as it has been confirmed to fit your vehicle. If you will be doing some towing, you will also need a ball like # 19256 for a 1-7/8 inch diameter or # 19258 for a 2 inch diameter. For trailer wiring use # 119178KIT. I have included instruction links for the wiring and hitch for you. If you will be using the...
    view full answer...

  • Trailer Hitch Recommendation for a 2011 Volkswagen Routan
  • When determining the overall towing capacity of a vehicle you must always go with the lowest rated component in the system as the overall capacity as a towing setup is only as strong as the weakest component. This is especially true if the weakest component happens to be the vehicle as that's the only component that can't be swapped out for a higher capacity component. The Hidden Hitch part # 87451 is confirmed to fit your vehicle and has more capacity than you will be able to use....
    view full answer...

  • Hitch Recommendation for a 2011 Ford Edge
  • I would recommend the Hidden Hitch part # 87604. This hitch has an e-coat base and is powder-coated on top of that for superior rust prevention over other hitches that only have powder-coating. This hitch is also a Class III 2 inch hitch that will give you more towing capacities and accessory options than a 1-1/4 inch hitch. I attached an install video for you to check out as well. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It...
    view full answer...

  • Hitch and Tandem Bike Rack Recommendation for a 2012 Ford Focus Sedan
  • The bike rack you referenced is designed to fit 2 inch hitches. I do have solution for you, but there are no 2 inch hitches available to fit your vehicle. For a hitch you will want to use the # 24872 that you referenced. I attached an install video for you to check out as well. The only tandem bike rack we offer that would work with a Class I 1-1/4 hitch like the # 24872 is the RockyMounts Tandem TailPipe # RKY1031.
    view full answer...

  • Trailer Hitch Recommendation For 2015 Honda CR-V
  • We offer three Class lll trailer hitches that are designed to fit your 2015 Honda CR-V. I recommend the Hidden Hitch Trailer Hitch, part # 87621. This hitch has a 2 inch receiver opening. The distance from the center of the hitch pin hole to the back edge of the bumper on a 2015 CR-V is 2 inches. The Curt part # C13119 and the Draw-Tite part # 75742, both have the same measurements from the pin hole to the back of the vehicle but I like the 87621 because it costs a little less than...
    view full answer...

  • Trailer Hitch and Wiring for a 2001 Mercedes E-Class
  • There are 2 different hitches available for the 2001 Mercedes E-Class. Hitch # C11830 fits E320 station wagon models. And Curt hitch # C11744 is designed for sedan models. So you would just choose the hitch based on which version you have, station wagon or sedan. We haven't installed either hitch on a vehicle yet so we do not have videos or our own pictures. But I can link the instructions for you so you can see what is involved in the installation process. If you plan on doing some...
    view full answer...

  • Recommended Wiring Setup for a 2015 Chevy Colorado Crew Cab Without a Tow Package
  • I contacted Curt Manufacturing and even though your 2015 Chevy Colorado Crew Cab doesn't have a tow package, the wiring connection point will be up under the bumper area, near the spare tire. You will use the Curt custom fit wiring # C56515. This will give you the 5-way flat trailer connector to power your trailer's signal lights. If it's a 4-way connector then use Hopkins wiring kit # 41155. A mounting bracket such as mounting bracket 4-pole flat # 18144 is something to consider because...
    view full answer...

  • Increasing Fuel Tank Protection on 2001 Jeep Grand Cherokee
  • Chrysler's solution to increasing the protection of the fuel tank on the Jeep Grand Cherokee was to install a trailer hitch. I have included a link to all of the hitch receivers available for your 2001. My personal recommendation is to go with a Class III hitch like the Curt, # 13051. A Class III hitch not only gives you the added towing capacity but by having the 2" opening you increase your options when it comes to hitch mounted accessories.
    view full answer...

  • Recommended Trailer Hitch for Cherokee 2015 Latitude 2x4
  • The Curt Class III Hitch, part # C13172 is indeed a fit for your 2015 Cherokee Latitude. If you don't already have a bike rack, you can't go wrong with the Thule Hitching Post Pro, part # TH934XTR, which is a popular bike rack for our customers who own the 2014 or 2015 Cherokee. If you'll be transporting women's bikes or bikes with sharply-angled top tubes, you might also consider a frame adapter bar like part # 64005. The bar spans the distance between the handlebar gooseneck and...
    view full answer...

  • Hitch Recommendation for a 1997 Oldsmobile 88 for Towing
  • For a hitch confirmed to fit your 1997 Oldsmobile 88 you would want the Draw Tite Hitch part # 36211. This hitch will attach to the frame of your vehicle and has towing capacities of 3,500 lbs total trailer weight and 300 lbs tongue weight. You will need to check the owners manual of your vehicle to determine the capacity for the vehicle and be sure not to exceed this figure. To complete your towing setup you may also be interested in the following products. Class II Drawbar 3-1/8"...
    view full answer...

  • Hitch Recommendation for a 2014 Toyota Camry Hybrid for Carrying Bike Rack
  • I have a solution for you, but since the Curt Hitch part # C12107 requires the use of a stabilizer strap like part # 18050 when used with a non-supported accessory like a bike rack I would instead recommend you go with the Draw Tite Hitch part # 36540 as it doesn't have the requirement.This way you won't have anything contacting any painted surfaces of your vehicle while carrying your bikes. The tech tips for this hitch install on your vehicle state that drilling is required for installation,...
    view full answer...

  • 2015 Nissan Murano Hitch Recommendation
  • The Hidden Hitch Trailer Hitch # 87679 that you referenced is a new hitch that has been confirmed to fit your 2015 Nissan Murano. It does not fit older models of the Murano, only the 2015. I confirmed this by checking with Hidden Hitch. The Hidden Hitch that fits the older Muranos is actually part # 87486. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a...
    view full answer...

  • Cargo Carrier Recommendation for a 2001 Ford Taurus with Draw Tite Hitch # 24699
  • The issue that you are running into is that the Draw Tite hitch part # 24699 that you referenced is a Class I hitch and the cargo carrier you bought is a Class II only accessory. That tab that you have found in the hitch is designed to prevent Class II accessories from being used in the hitch. This is so you don't overload the hitch. Realistically the only solution I can recommend for you would be to go with a Class I rated cargo carrier like the # C18145. Check out the review video...
    view full answer...

  • What Size Socket or Wrench Is Needed to Install Curt Hitch part # 13322
  • The install hardware that is included with the Curt Hitch part # 13322 that you referenced includes bolts that are M14-2.00. That size of bolt head calls for a 21 millimeter socket or wrench. I attached an install video for you to check out as well.
    view full answer...

  • Trailer Hitch Recommendation for a 2004 Volkswagen Jetta GLS
  • The reason the Curt Hitch part # C11070 that you referenced won't fit a GLI is because the GLI models have OEM ground effects. The GLS models do not have the ground effects so the # C11070 would fit. I attached an install video for you to check out as well. If you are looking to doing any light towing with your vehicle, I would also recommend these items listed below. Wiring Kit # 119178KIT 2 inch Hitch Ball # 19258 1-7/8 inch Hitch Ball # 19256
    view full answer...

  • Recommended Trailer Hitch and Ball Mount for a 2009 Chevy HHR
  • The trailer hitch I recommend is the Draw-Tite Class I # 24756 and Draw-Tite ball mount # 3594 because the top of the receiver to the ground is 10-1/4 inches and the ball mount will give you a 4-inch rise. As a result, giving you a 14-1/4 inch ground clearance and stay above the 13-1/2 inches. The weight will bring the clearance down a tad from the 14-1/4 inch clearance which will keep your trailer more level. The wiring for your 2009 Chevy HHR is # 118407 and 1-7/8 hitch ball is # 19256.
    view full answer...

  • Trailer Hitch for Carrying 350lb Dirt Bike in Hitch Mounted Carrier on 1999 Ford Explorer
  • The Curt Class III hitch you referenced, part # 13540 will indeed allow you to retain the full-sized spare in place under the rear of the vehicle. If the 350 lb figure you mentioned is just the weight of the bike, not including the carrier you'll be overloading the hitch. In that case, I'd recommend the Draw-Tite Class III, part # 75096 which has a 500 TW capacity and would also allow the spare tire to remain in place. Even if that 350 lb figure included the weight of the carrier, I'd...
    view full answer...

  • Hitch Mounted Options for Carrying 540lb Motorcycle with 2001 Nissan Frontier
  • Although we do offer tray-style motorcycle carriers, the 400-500 lb tongue weight capacity of the hitch, which is the maximum downward force that can safely be applied, would be exceeded by the weight of your bike. This would cause the hitch or its attachment points on the truck to fail while you're transporting the bike, which would be very bad. If your bike is smaller than a 750cc, a hitch mounted carrier like part # RHMC2 would be a good alternative if the tires on your bike are between...
    view full answer...

  • Trailer Hitch Recommendation for a 2000 Toyota Tacoma
  • For a Draw Tite Hitch that has been confirmed to fit your 2000 Toyota Tacoma you would want the part # 75078. The part # 75031 that you referenced is designed to fit older Toyota trucks so I cannot recommend it for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch...
    view full answer...

  • Trailer Hitch Recommendation for a 2005 Subaru Forester
  • The difference between the Curt Hitches part # C120383 and part # C12038 is that the # C120383 comes with a ball mount that you would use for towing and the other hitch does not. Either hitch would fit your 2005 Subaru Forester. I attached an install video for you to check out as well. Then you will need to add a properly sized ball and the wiring. Those items are not included with the hitch. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring...
    view full answer...

  • Trailer Hitch Recommendation for a 2015 Volkswagen Golf
  • All of the hitches we offer for the 2015 Volkswagen Golf are confirmed to fit all models except for the R models. The Draw Tite hitch part # 24925 that you referenced will fit either a TDI or the gas models so it would be the one to use as long as you don't get the R model with the center exhaust. With that being said, I recommend the ball mount # C45016 as it fits 1-1/4 inch trailer hitch receivers. For a 1-7/8 inch hitch ball, go with # 19256. For a 2-inch hitch ball # 19258...
    view full answer...

  • Trailer Hitch Recommendation for a 2014 Ford Escape
  • The etrailer.com Ball Mount Kit part # 989900 does not include a wrench to tighten the hitch ball down. For a wrench to go with this kit you would want the part # 62342. For a trailer hitch the part # 87627 that you referenced would be the correct hitch to use. I attached an install video for you to check out as well. For trailer wiring you would want the part # 118566.
    view full answer...

  • Hitch Recommendation for a 2012 Dodge Ram 1500 without Factory Hitch
  • For your 2012 Ram 1500 without a factory hitch the correct part number for a Curt Class IV hitch would be the # 14374. The # 14361 is designed to fit older 1500 models so it would not work for you. I attached an install video for you to check out as well.
    view full answer...

  • Hitch Recommendation for a 2011 Mercedes Benz E350 Sedan
  • For your 2011 Mercedes E350 Sedan the only hitch we have available for it is the Curt Hitch part # C11001. This hitch has a 1-1/4 inch opening like you mentioned. 2 inch hitches are typically reserved for larger vehicles like SUVs and trucks. The only solution I have for you would be to get this hitch and then also upgrade to a bike rack and cargo carrier confirmed to fit this hitch size. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman...
    view full answer...

  • Long Hitch Extension and High Capacity Hitch Recommendation for a Ford F250 Super Duty
  • Sounds like you are looking for a setup that will allow you to use a longer hitch extension than the 24 inch bar you are currently using without reducing your towing capacity. If you use the TorkLift SuperTruss Hitch Extension # TLE1536 which is 36 inch extension with a TorkLift SuperHitch Original # TLF1002 you will have the following capacities: Maximum gross trailer weight: 6,500 lbs. Maximum GTW when used with weight distribution: 12,000 lbs Maximum tongue weight: 650 lbs Maximum...
    view full answer...

  • Hitch Recommendation for a 2016 Kia Sorento
  • The Curt hitch part # C13195 has been confirmed as a fit for your 2016 Kia Sorento so I would recommend it for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right rise or drop to tow the...
    view full answer...

  • Recommended Hitch for 2014 Honda CRV Carrying a Scooter Carrier
  • As long as your daughters 2014 Honda CR-V has the tongue weight rating to carry the weight of the scooter and the lift you could use a hitch like the # 75742 to carry the scooter carrier. This hitch has a tongue weight capacity of 350 lbs, you will need to consult the owners manual of the CR-V to determine what Honda recommends as the tongue weight capacity and be sure not to exceed the lower of the two figures. As long as you center the scooter on the carrier you wouldn't have to worry...
    view full answer...

  • Hitch Recommendation for a 2011 Buick Lacrosse CXL and CXS
  • Actually both the Draw Tite Hitch # 36538 and the Hidden Hitch part # 90242 that you referenced are made by the same company so they are basically identical. Either would work great for you. The Harmar AL160 is a scooter carrier, if the one you are looking at is confirmed to fit a 1-1/4 inch hitch it should work with either hitch previously mentioned. The weight of the carrier plus your scooter could not exceed 300 lbs otherwise it would be too heavy for either hitch.
    view full answer...

  • Does the Trunk Pan Shield Get Removed to Install Hidden Hitch 87755 on a 2007 Mercedes ML350
  • The installation instructions for the Hidden Hitch part # 87755 that you referenced say that if you want to reinstall the trunk pan shield you can trim it so that it is compatible with the hitch, but when we installed this hitch on a similar vehicle as your 2007 MB ML350 we just left it off. I attached a link to this video as well.
    view full answer...

  • Trailer Hitch for a 1996 Chevy S-10 with Roll Pan Bumper
  • We do have a trailer hitch for your 1996 Chevy S-10 with the roll pan bumper. it is Curt hitch # 13920. I have included a link to the installation instructions for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount...
    view full answer...

  • Highest Rated Hitch Recommendation for a 1997 Dodge Ram 3500
  • The highest rated hitch we offer for your 1997 Dodge Ram is the Curt Hitch part # C15300. The capacities for this hitch are 2,400 lbs tongue weight and 17k total trailer weight when used with weight distribution. It doesn't look like this hitch would have enough capacity for the trailer you plan to tow unless you can reduce the weight of the trailer by 1,000 lbs or so. You will need a weight distribution system though. To get the full weight capacity you would need a WD system will be...
    view full answer...

  • Recommended Trailer Hitch for a 2015 Toyota Sienna
  • Yes, there are several trailer hitches that will fit your 2015 Toyota Sienna Limited AWD. The hitch I recommend is the Curt Class III # C13105. It will have a 350 pound tongue weight which will be just fine for carrying a bike rack like the Swagman Trailhead # S63360 that has a 3-inch rise in the shank. I included a link to all the trailer hitches that will fit your 2015 Toyota Sienna (Class II and III) along with a couple installation videos and informative article.
    view full answer...

  • Recommended Trailer Hitch for a 2014 Nissan Versa Note
  • I recommend the Draw-Tite I hitch # 24909 as the towing capacity is 2,000 pounds and will have a maximum tongue weight of 200 pounds. It's corrosion resistant and the fully welded steel construction ensures great strength and durability. A pin and clip is included with this Draw-Tite hitch # 24909 and if you plan on doing any light duty towing, I recommend the ball mount # 3592, 2-inch hitch ball # 19258 or 1-7/8 hitch ball # 19256 and wiring by Tow Ready # 118582. I would double check...
    view full answer...

  • Recommended Trailer Hitch for a 2013 Honda Odyssey Pulling Fully Loaded Trailer with a UTV
  • The trailer hitch I recommend is the Hidden Hitch Class III # 87479 and it will have a maximum tongue weight of 350 pounds and gross trailer weight of 3,500 pounds. The wiring you need is # 118521, and ball mount kit I recommend is # EBMK4 which will include an interchangeable ball set, ball mount with 2-3/4 inch rise or 4-inch drop, pin and clip and a storage bag. With that said though, you will not want to exceed the 350 pound tongue weight because it could bend the hitch and potentially...
    view full answer...

  • Hitch and Wiring Harness Recommendations for 2014 BMW 3-Series 328d Sedan
  • The 1-1/4-inch Class I trailer hitch you referenced, Curt # C11367, is indeed a correct confirmed fit for the 2014 BMW 328d sedan. This light-duty hitch bolts on using included hardware and if desired it can be ordered with a ball mount for towing. For the 1-7/8-inch ball version order # C113671; for a 2-inch ball order # C113672; if you already have a hitch ball that fits your jet ski trailer coupler then you can order # C113673 that includes a standard ball mount. make sure you choose...
    view full answer...

  • Trailer Hitch Recommendation for a 2009 Isuzu Rodeo
  • The Hidden Hitch part # 70498 that you referenced has been confirmed to fit your 2001 Isuzu Rodeo as long as it has its spare mounted under the vehicle. If the spare is on the rear door you would instead want the # 87473. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch...
    view full answer...

  • Hitch and Trailer Wiring Recommendation for a 2015 Subaru Forester
  • For your 2015 Subaru Forester either the Curt Hitch part # C13144 or the Hidden Hitch part # 87654 would work well for you. If it were me I would go with the one that costs less. Both hitches have the same capacities and will install in basically the exact same way. Since you do not have a factory trailer wiring you will need to start with a 4-way (if you do not have one). For that you would want the # C56040. From there you would need to convert the 4-way to a 7-way so that you...
    view full answer...

  • Stabilizer Strap Recommendation for Curt Hitch C13130 on a 2013 Acura RDX
  • The correct stabilizer strap to use with the Curt Hitch part # C13130 that you referenced is the part # 18050. To see how it would get used check out the review video I attached. Another option you have that might interest you is to use a Hidden Hitch like part # 87642. Hidden Hitch does not require the use of a stabilizer strap. I attached an install video for this hitch for you to check out as well. The most popular bike rack we carry that has been confirmed to fit this vehicle...
    view full answer...

  • Replacement Hardware Recommendation for the Curt Hitch part # C12232
  • Yes we do, the part number you will need is # RHK. You will need to select Curt from the drop down menu and you will need to enter the part number C12232 in the part box and we will ship you out the correct replacement hardware.
    view full answer...

  • Hitch Lock and Anti-Rattle Device for Curt Hitch 13581 on a 2011 Mitsubishi Outlander GT
  • An anti-rattle hitch lock that uses a regular hex-head bolt should fit your Curt trailer hitch # 13581. Take a look at # SR25219. The head will be approximately 3/4 inches wide so measuring from the center of the hitch pin that would be 3/8 of an inch. If you have 3/8 of an inch from the center of the pin hole to the bar on your hitch then this lock would work. Another option is to use a regular hitch lock such as # 5201 and a stand-alone anti-rattle device like # BX88224.
    view full answer...

  • Hitch Recommendation for a 2015 Subaru WRX
  • Yes, I spoke with my contact at Curt and the Curt Hitch part # C11408 that you referenced has been confirmed to fit the 2015 Subaru WRX so it will work for you. The hitch will hang below the rear bumper when installed. I attached a picture that shows this hitch installed as well. For a ball mount you would want part # C45521, 1-7/8 inch hitch ball # 19256, 2 inch hitch ball # 19258. For trailer wiring you would want the part # C56259.
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Subaru WRX
  • The Curt trailer hitch # C11408 will not be concealed behind the rear fascia of your 2015 Subaru WRX. The cross tube and receiver will be visible beneath the rear fascia. Take a look at the installation instructions I have linked that shows some pictures of the hitch position. If you plan on doing some towing the correct ball mount to use is # C45521. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # C56259. If you will be using the...
    view full answer...

  • Trailer Hitch for Scooter and Lift for a 2011 Buick LaCrosse
  • If the rear of your 2011 Buick LaCrosse is 6-1/2 inches from the ground on the driveway incline then anything that extends out further then that would be even closer to the ground. Basically you can probably expect to scrape the ground with a carrier installed in the trailer hitch. The way around this would be if the carrier you use had a rise in the shank effectively increasing its ground clearance. Carrier # PS10401-10402 for example has a slight rise in the shank (4 inches) and would...
    view full answer...

  • Rust Resistant Hitch Recommendation for a 2015 Ford Explorer
  • For your 2015 Ford Explorer I would recommend you go with the Draw-Tite Trailer Hitch # 75710. This hitch has an e-coat base plus powder coating to help prevent corrosion. The Curt hitch part # C13100 only has a powder coat finish so it won't fight corrosion quite as well. I attached a help article on rust prevention for you to check out as well. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch...
    view full answer...

  • Recommended Trailer Hitch and Towing Accessories for 2001 Nissan Frontier
  • Curt, Hidden Hitch and Draw-Tite all offer hitches for your Frontier. All three hitches share a similar design and would install in the same manner. Due to the fact that the Curt # 13841 has a slightly higher rating (500 lb Tongue Weight/5000 lbs towing, versus 400 lb Tongue weight/4000 lbs towing) of the other two, as well as having a lower price, I'd recommend the Curt hitch. Curt makes a great product, so you won't sacrifice anything by going with the lower cost hitch. Keep in mind...
    view full answer...

  • Recommended Trailer Hitch And Bike Carrier For 2014 Subaru Outback Wagon
  • Even though the generation of the Subaru Outback has not changed, through the years the mounting holes and models could have slight differences. I would use the measurement we have for the 2014 as a reference when looking at hitch-mounted accessories like a bike rack. Since Hidden Hitch, part # 87568 and Draw-Tite, part # 75673 are made by the same parent company and have the same weight carrying capacities, I recommend the Hidden Hitch, part # 87568 because of the small difference...
    view full answer...

  • Fabricating a Ball Mount for a Curt Class I Trailer Hitch on a 2009 Volkswagen Jetta SportWagen
  • Yes you would need 1-1/4 inch square tubing to fabricate something for the Class I trailer hitch # C110723 for your 2009 VW Jetta SportWagen. I would urge you to use caution since the offset of the design will put additional stress on the receiver and it is not really designed for what would essentially be a twisting force in the receiver. But if the antenna is not too heavy it shouldn't be a problem. The center of the 1/2 inch diameter hole in the shank should be 1-1/2 inches from...
    view full answer...

  • Hitch Recommendation for a 2007 Land Rover Range Rover Sport HSE Model
  • For your 2007 Land Rover Range Rover Sport HSE Model you would want the Curt Hitch part # 13456. I attached an install video for you to check out as well. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not...
    view full answer...

  • Trailer Hitch and Wiring for a 2013 Ford E-350 Van
  • All of the trailer hitches we carry for your 2013 Ford E-350 van use 6 bolts to attach to the vehicle frame. The hitches are given their ratings based on several factors, including how they mount to the vehicle so having 6 bolts to mount a hitch does not diminish its rated capacity. But if you want an 8-bolt hitch none of the options we have use more than 6. The most popular hitch for your van is Curt hitch # 14055 rated for 1,000 pounds tongue weight and 10,000 pounds gross trailer...
    view full answer...

  • Hitch Recommendation for a 2014 Toyota Prius
  • We have everything needed for your Prius to tow a small trailer, but you will want to check the owners manual of your vehicle to determine if Toyota recommends you tow with your vehicle. For a hitch for your 2014 Toyota Prius you would want the Hidden Hitch part # 60263. You'd also need a trailer ball, like part # 19256 for the 1-7/8 inch or # 19258 for the 2 inch ball. A trailer wiring harness, part # 119147KIT would also be needed.
    view full answer...

  • Trailer Hitch and Wiring for a 2010 Nissan Xterra
  • We have everything you need to tow with your 2010 Nissan Xterra. The most popular and economical trailer hitch for your Xterra is # 13514. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right...
    view full answer...

  • Choosing a Ball Mount for Use with Curt Hitch # C11158 on 2014 Ford Focus SE Hatchback
  • The Curt Class I trailer hitch you referenced, part # C11158, is indeed a correct choice for your 2014 Ford Focus SE Hatchback. As noted in the linked installation video at the 18-second mark, the top of the receiver opening will be approximately 10-3/4-inches above the ground once installed. With this hitch you will need to use one of the ball mounts recommended by Curt. The hitch comes with a choice of sizes of matching Euro style ball mount. For the hitch and 1-7/8-inch ball order...
    view full answer...

  • Trailer Hitch and Bike Carrier Recommendations for a 2014 Ford Focus
  • The further the trailer hitch receiver is recessed under the back of a vehicle the less clearance there is for accessories and the harder it is to pin in any accessories to the trailer hitch. The Draw-Tite hitch # 24872 measures 2 inches from the center of the hitch pin hole to clear the rear bumper. To me, that is perfect. Curt trailer hitch # C11158 we have installed on a 2012 Focus sedan but not a 2014 hatchback like in the other video so it is really not a fair comparison. But on...
    view full answer...

  • Choosing a Hitch for 2010 Dodge Grand Caravan with Stow-N-Go Seats
  • Your 2010 Dodge Grand Caravan with Stow-N-Go Seats can be fitted with either a light-duty 1-1/4-inch Class II hitch or a heavier duty 2-inch Class III type. We offer options in both sizes and all will fit your version of the Grand Caravan with Stow-N-Go seats. The link will let you see all options. I suggest a heavier-duty Class III type hitch because it will give you a greater safety margin and also be more widely compatible with a whole range of accessories like bike racks and cargo...
    view full answer...

  • Trailer Hitch for a 2015 Ram 1500 for up to 7,000 Pound Travel Trailer
  • Since you are looking at travel trailers upwards of around 7,000 pounds I recommend a hitch that has a 10,000 pound capacity. But you will also want to check the truck owners manual to determine the towing capacity of your specific 2015 Ram 1500. Whichever is lower, the hitch or the truck, is the capacity you need to go by. The most popular hitch with 10,000 pound capacity that fits your truck is Curt hitch # 14374. I have linked a video showing how the hitch installs. I also recommend...
    view full answer...

  • Hitch Recommendation for a 2002 Chevy S-10 Extreme with Roll Pan Bumper
  • The Curt Hitch part # 13920 has been confirmed to fit your 2002 Chevy S-10 Extreme with a roll pan bumper. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right rise or drop to tow the trailer level,...
    view full answer...

  • 7-Way and Brake Controller Recommendation for a 2014 GMC Terrain
  • Since you do not have a factory trailer wiring you will need to start with a 4-way (if you do not have one). For that you would want the # 56094. From there you would need to convert the 4-way to a 7-way so that you can install the brake controller. For that you will want the Brake Controller Install Kit and 7-Way Adapter part # ETBC7. I attached installation instructions and an install video for this product as well. This also will give you a 12 volt accessory power circuit. For...
    view full answer...

  • Recommended Trailer Hitch and Bike Rack for 2014 Acura TL
  • If you are concerned about voiding the warranty of your 2014 Acura TL, I recommend checking the towing section in your owner's manual if you plan on installing a trailer hitch. Honda states the Acura TL was not designed for towing and doing so could void the warranty. That is something to keep in mind before installing a trailer hitch. For a trailer hitch, you have three options. I have attached a link to them for you to check out. The Draw-Tite Sportframe Class I Trailer Hitch, # 24899,...
    view full answer...

  • Trailer Hitch for 2008 Smart fortwo Passion
  • According to Curt Manufacturing, their Class I # C11020 hitch is a fit for all 2008-2014 Smart fortwo models except for the Barabus model. Since the Passion is a trim level, and not a specific model, the hitch will fit just fine. If you were needing a cargo carrier or bike rack, be sure to choose something that's compatible with a Class I hitch. Curt's hitch warranty stipulates that a stabilizing strap like part # 18050 must be used for non-trailer loads like cargo carriers or bike racks. I'll...
    view full answer...

  • Best Way to Transport Expensive Bikes with a 2010 Honda Accord CrossTour
  • We have hitches that are designed to fit your 2010 Honda Accord Crosstour. Hitch mounted bike racks are the way to go, especially for transporting expensive bikes for a long period of time. For a hitch you would want the Draw Tite Hitch part # 24852 as this has been confirmed to fit your vehicle. For a top of the line bike rack to use with this hitch I would recommend the Thule T2 Bike Rack part # TH917XTR. This rack is compatible with the hitch I referenced, can lock to your hitch and...
    view full answer...

  • How Do Curt Stabilizer Straps Work for Supporting Hitch Accessories
  • The stabilizer strap part # 18050 that Curt recommends you use when you are carrying a non-supported hitch accessory like a bike rack will get attached to the rack and then the other end of the strap will clip to the top of the hatch or trunk of the vehicle it gets used on. Check out the review video I attached for the strap. The Curt Hitch part # C12490 that you referenced is for a Scion xB, for a vehicle like this the strap would get attached to the top of the rear cargo door. I attached...
    view full answer...

  • Recommended Trailer Hitch And Cargo Cargo Carrier For 2014 Scion xB
  • It sure looks like you have been doing your homework. The Curt trailer hitch, part # C12490 is the hitch designed to fit your 2014 Scion xB. This is a Class l trailer hitch with a 1-1/4 inch receiver opening. And the note from Curt states that all non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps like part # 18050. Failure to properly support these loads will void your hitch warranty from Curt. This is a simple no-drill installation...
    view full answer...

  • Hidden Hitch Recommendation for a 2012 Jeep Grand Cherokee
  • I have a hitch recommendation I can make for your 2012 Jeep Grand Cherokee, but we no longer carry the Bosal brand of hitches. Instead I can recommend the Hidden Hitch brand hitch part # 87595 that has been confirmed to fit your vehicle. I attached an install video for you to check out as well. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch...
    view full answer...

  • Replacement Hitch Install Hardware for a 2000 Buick LeSabre
  • We can help you, but you will need to know what hitch manufacturer made the hitch you have and what part number it is. The part number you will need is # RHK. If for example you had the Draw Tite Hitch part # 36309 you would need to enter the part number 36309 on the product page and then select Draw Tite from the drop down menu and we will ship you out the correct hardware kit. I attached an install video for you to check out as well for this hitch on a similar LeSabre as yours.
    view full answer...

  • Hitch Recommendation for a 2016 Acura MDX
  • The Curt Hitch part # C13146 that you referenced will fit the 2016 Acura MDX with and without the rear sport bumper trim so it will work for you. For trailer wiring you would want the part # 118628. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a...
    view full answer...

  • Hitch Recommendation for a 2006 Subaru Forester
  • The only hitch size available for your 2006 Subaru Forester is a 1-1/4 inch hitch like the Draw Tite hitch part # 36311 that is a Class II hitch. 2 inch hitches are used on larger vehicles like SUVs and trucks. I attached a help article on hitch sizes for you to check out as well. You could use a hitch adapter like part # HTAD to convert the hitch opening to a 2 inch opening, but you should note that hitch adapters like this cut the capacity of the hitch in half. I attached a help...
    view full answer...

  • Could the Safety Chain Loops of the Hidden Hitch for a 2011 Nissan Murano be Used for Tow Hook
  • The tow hook loops of the Hidden Hitch part # 87486 that you referenced were designed to have the same capacity as the hitch so they would work in the event of you needing them. Or if you wanted a hitch mounted tow hook you could use the part # TR63044.
    view full answer...

  • Hitch Recommendation for a 2014 Grand Cherokee SRT
  • All of the hitches we carry that are confirmed to fit your 2014 Jeep Grand Cherokee SRT like the Draw Tite Hitch part # 75699 that you referenced will hang below the bumper fascia. Only an OEM hitch would fit the hitch cover opening you have at the rear of your vehicle. Also, this hitch only has a 7,500 lb capacity when used with a weight distribution system. If you are unfamiliar with them check out the help article I attached for them.
    view full answer...

  • Trailer Hitch and Wiring for a 2010 Dodge Grand Caravan
  • The designs of trailer hitches from different manufacturers for a given vehicle often look the same. This is because the hitches have to be a certain shape to fit nicely under the vehicle. The most popular hitch for your 2010 Dodge Grand Caravan is Curt hitch # 13364. This is a Class III trailer hitch with a 2 inch receiver. It is rated for 400 pounds tongue weight and 4,000 pounds gross trailer weight. Consult the vehicle owner's manual for the towing capacity of the van. Whichever...
    view full answer...

  • Recommended Trailer Hitch for 2013 Lexus CT200h
  • Curt Trailer Hitch, # C11200, is a confirmed fit for the 2013 Lexus CT200h. You will want to check the owner's manual for your specific vehicle before adding a trailer hitch and any accessories. If you want a hitch bike rack, we have a few dozen class I-compatible racks to choose from, click the provided link to see them. To maintain the hitch warranty, Curt requires the use of a stabilization strap like part # 18050 on any non trailer load carried by the hitch. The Thule Helium Aero...
    view full answer...

  • Install Hardware Recommendation for a Draw Tite Hitch on a 2000 Toyota Camry
  • To install the Draw Tite Hitch part # 36336 on your 2000 Toyota Camry you would need to use the included install hardware that is M10 x 1.25 x 30 mm. Or if you wanted us to send you all new install hardware for this hitch you would need part # RHK. On the product page you would enter Draw Tite as the manufacturer and 36336 as the part number and we'll ship you out all the needed hardware to install this hitch.
    view full answer...

  • Trailer Hitch Recommendation for a 2011 Jeep Grand Cherokee with Dual Exhaust
  • Yes, both the round tube Curt hitch part # C13182 and the square tube Curt hitch part # C13065 have been confirmed to fit all models of the 2011 Jeep Grand Cherokee (including models with dual exhaust) so either would work well for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch...
    view full answer...

  • Hitch Recommendation for a 2013 Hyundai Veloster
  • If you have basic tools and basic mechanical skills I would be confident in your ability to the install the Curt Hitch part # C11254 on your 2013 Hyundai Veloster. It's not very complicated and would only take you about 40 minutes to install. Check out the install video I attached for more info. Hitch installs are pretty easy for qualified mechanics. If you wanted to let someone else install the hitch I would just find a local garage in your area that has a good reputation and let them...
    view full answer...

  • Hitch Option for a 1960 Ford F100
  • We don't have any custom fit hitches confirmed to fit your 1960 Ford F-100, but a multi-fit hitch like the # 41990-07 could possibly work. I'd recommend using a hitch like this or having one professionally fabricated by a qualified welder.
    view full answer...

  • Does Using Additional Washers to Install a Hitch on a 2004 Subaru Outback Affect Capacity.
  • I spoke to my contact at Curt and he said that as long as you install enough washers for the attachment point to the tow hook so that the hitch sits solidly against it the capacity of the hitch won't be reduced at all. The issue would be the same for the Draw Tite Hitch part # 36284 and Hidden Hitch part # 90176.
    view full answer...

  • How to Store a 4-Way Harness Out of Plain Sight
  • What you could use to keep the 4-way trailer connector you have installed on your 2011 Dodge Durango is use the 4-way Bracket part # HM48595. This will attach to the lower fascia of your vehicle and will allow the connector to be as out of sight as you like based on where you install it.
    view full answer...

  • How to Pick Out a Weight Distribution System for a 2006 Honda Pilot EX-L AWD
  • Weight distribution systems apply a different angle of torque on the hitch and vehicle they are installed on than not using one. A lot of the time the problem isn't that the hitch can't handle the WD system it's that the vehicle's attachment points can't handle the added stress. The spring bars of a system take and apply the tongue weight of the trailer and transfer it through the hitch and vehicle back up to the front axle. You can imagine that puts a different kind of strain on a vehicle/hitch...
    view full answer...

  • Trailer Hitch with Best Ground Clearance for a 2015 Volkswagen Golf
  • On your 2015 Volkswagen Gold Curt trailer hitch # C11355 will have the receiver slightly below the rear fascia. If you measured up from the ground to the bottom of the rear fascia and then subtracted 1-3/4 inches that would be approximately where the bottom of the hitch would be. Draw-Tite hitch # 24925 would be the better option. It is tucked up a little higher compared to the Curt hitch so I recommend going with it. For a bike rack you will need one that is compatible with a Class...
    view full answer...

  • Recommended Trailer Hitch For 2014 Chevrolet Impala LTZ2
  • We have several trailer hitches that are designed to fit your 2014 Chevrolet Impala LTZ. We have not had an opportunity to install a hitch on a 2014 Impala but we have installed some hitches on a 2014 Malibu. I will make my recommendations based on the Malibu. The hitch I recommend is the Draw-Tite Trailer Hitch, part # 36543. This is a Class ll hitch and has a 1-1/4 inch receiver opening. As the attached installation video shows, the distance from the center of the hitch pin hole...
    view full answer...

  • Hitch Recommendation for a 2015 Volvo V60
  • Between the two hitches you referenced that are both confirmed to fit your 2015 Volvo V60 the biggest differences are that the Draw Tite Hitch part # 75916 has a 400 lb tongue weight capacity as well as a 4,000 lb total trailer weight capacity. Whereas the Curt # 13266 has a 350 lb tongue weight capacity and a 3,500 lb trailer weight capacity. Also, the Draw Tite hitch does not require the use of a stabilizer strap when carrying a non-supported load like a bike rack or cargo carrier....
    view full answer...

  • Hitch Recommendation for a 2015 Volkswagen Jetta TDI
  • I spoke with my contact at Draw Tite and the hitch part # 24926 has been confirmed to fit your 2015 Volkswagen Jetta TDI so it should work well for you. This hitch will actually fit all models of the 2015 Jettas except the hybrids. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike Rack part # S64670. This rack has a ton of positive reviews from our customers who have tried it. Check out the review video I attached for more info.
    view full answer...

  • Recommendation for Transporting Bikes with a 2014 Toyota Corolla
  • It is always advised to follow the towing recommendations of the manufacturer of a vehicle, failure to do so can void vehicle warranties. That being said we do carry hitches for your 2014 Toyota Corolla like the Draw Tite Hitch part # 24913. I attached an install video for you to check out as well. Another option for transporting bikes that doesn't require a hitch is a trunk mounted bike rack like the Thule Raceway Bike Rack part # TH9001PRO that has been confirmed to fit your vehicle. What...
    view full answer...

  • Hitch Recommendation for a 2014 Toyota Avalon for Carrying Bike Rack
  • For a hitch for your 2014 Toyota Avalon I would recommend the Draw Tite Hitch part # 36540. This would be a great hitch to use for carrying a bike rack. I don't have a specific installer I can recommend for you to use, but hitch installations are pretty basic, any qualified mechanic in your area would do an excellent job. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike Rack part # S64670. This rack has a ton of positive reviews...
    view full answer...

  • Hitch and Bike Rack Recommendation for a 2013 Chevy Camaro RS Convertible
  • For your 2013 Chevy Camaro Convertible RS you would want the Curt Hitch part # C11222 as this hitch has been confirmed to fit your vehicle. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike Rack part # S64670. This rack has a ton of positive reviews from our customers who have tried it. Check out the review video I attached for more info. With this Curt hitch all non-trailer loads - bike racks, cargo carriers and so forth - should...
    view full answer...

  • Hitch Recommendation for a 2007 Ford Escape Hybrid
  • The Curt Hitch part # 13650 that you referenced has been confirmed to fit your 2007 Ford Escape Hybrid and would work great as it has a 2 inch opening that will give you more capacity and flexibility. I attached an install video for you to check out as well. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a...
    view full answer...

  • Trailer Hitch for a 2015 Volkswagen GTI
  • Hidden Hitch has not confirmed the fit of any trailer hitches for the 2015 Volkswagen GTI which is why you do not see it listed. We could test fit a hitch but we would need a willing volunteer in the Wentzville, Missouri area. Since Golf and GTI are separate models that is why there are other options for it. The Hidden Hitch models for the 2014 Golf are different than the ones listed for the 2014 GTI so Hidden Hitch will likely produce an all new hitch for the 2015 GTI. Basically...
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Toyota Highlander
  • Curt trailer hitch # C13200 will have the face of the receiver pretty much flush with the back bumper on your 2015 Toyota Highlander. I have included a picture out of the instructions, also linked, that shows the hitch installed. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball,...
    view full answer...

  • Trailer Hitch And Wiring Recommendation For 2013 Volkswagen Tiguan
  • We have a few trailer hitches designed to fir your 2013 Volkswagen Tiguan. I recommend the Curt Trailer Hitch, part # C13133. This is a Class lll hitch and has a 2 inch receiver opening. This hitch is rated with 3,500 lb towing capacity and 350 lb tongue weight capacity. You will want to check your owner's manual or with your dealership to make sure you do not exceed the towing or tongue weight capacity for your Tiguan. Using a heavier duty hitch does not increase the towing capacity...
    view full answer...










Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com