view cartView Cart

Shop by Vehicle


Filter Questions and Answers:


reset filter
Trailer Hitch
Trailer Hitch
 

Expert Answers about Trailer Hitch


  • Will the Spare Tire Be Hard to Access After Installation of Curt Hitch on a 2014 Toyota Highlander
  • I believe I found the picture you are referring to and have attached to this page. The hitch does somewhat cover the tire portion of the spare, but it really wouldn't be much effort to position the spare around the hitch as you raise or lower it. We haven't heard anything from any of our customers that would indicate that it would be difficult at all.
    view full answer...

  • Hitch Recommendation for a 2005 Subaru Outback
  • The two vehicles you referenced are different enough that one hitch style does not fit both. If you have a 2005 Subaru you will want a # 60303 if you have a hatchback or part # 60893 if you have a sedan. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike Rack part # S64670. This rack has a ton of positive reviews from our customers who have tried it. Check out the review video I attached for more info.
    view full answer...

  • Recommended Trailer Wiring Harness for 2015 Hyundai Santa Fe Sport
  • The Tow Ready # 118269 is a fit for all models of the 2015 Hyundai Santa Fe. Just to be sure, I've confirmed this with Tow Ready for you. The Curt Class III hitch, part # C13152 is a fit for the 2015 Sport model. In addition to the hitch and the wiring, you'll also need a # 2923 and a # 63845 for a 2 inch ball mount or # 19260 for a 1-7/8 inch ball mount (depending on what your trailer requires). If you click the link I've provided for you, you can see an install video showing the...
    view full answer...

  • Trailer Hitch and Wiring for a 2014 Hyundai Elantra GT Hatchback
  • We rate hitch installation difficulty based on the amount of time it takes for a professional or skilled layman to complete the installation. The hitches that take the least time to install are Draw-Tite hitch # 24905 and Hidden Hitch # 60336. The estimated pro installation time is 30 minutes so their difficulty is rated a 3 out of 10. The only difference between these two hitches is that the Hidden Hitch model, # 60336, comes with a ball mount, pin, and clip. The Draw-Tite model is...
    view full answer...

  • How Much of Curt Trailer Hitch # C11030 is Visible on 2011 Mercedes C300 4-door Sedan
  • I do not have the exact measurement but I do have two images of the Curt trailer hitch # C11030 installed on the 2011 Mercedes-Benz C300 sedan / 4-door for you to check out. As you can see, the hitch is very unobtrusive. With the Curt Stabilizer Strap, # 18050, you'll take the clip end and hook it on the lid of the trunk. I have also included a video of the Support Strap which shows this installation procedure.
    view full answer...

  • Hitch Recommendation for a 2004 Volkswagen Golf to Tow Small Camper
  • The Curt Hitch part # C11066 that you referenced has been confirmed as a fit for your 2004 Volkswagen Golf GTI. The hitch itself has the towing capacities of 2,000 lbs trailer weight and 200 lbs tongue weight. As long as your trailer stays under this figure and the towing capacities that are listed for your vehicle in the owners manual you would be good to go. To complete your towing setup you may also be interested in purchasing the following: Draw-Tite Wiring # 119178KIT (installation...
    view full answer...

  • Hitch Availability for a 2000 Dodge Ram Van
  • The 44065C was a hitch made by Reese for a Dodge Ram Van made in the 90's like the Hidden Hitch part # 87492. It is hard to tell exactly what you are looking for but it almost sounds like are interested in finding a hitch cover with Reese on it like the # 86066 which is a Reese made hitch cover. The other part number you referenced doesn't reference anything that I could find.
    view full answer...

  • Trailer Hitch Recommendation for a 2005 Lexus GX470
  • For your 2005 Lexus GX470 we do have hitches available. The most popular one is the Hidden Hitch part # 70779. This is a Class III hitch with a 2 inch opening that has plenty of towing capacity. I attached an install video for you to check out for more info. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes...
    view full answer...

  • Trailer Hitch Recommendation for a 2012 Fiat 500
  • The Hidden Hitch part # 60289 that you referenced has been confirmed to fit your 2012 Fiat 500 POP. This has a 200 lb tongue weight rating and a 2,000 lb total trailer capacity so it should work very well for you as long as the owners manual of your vehicle says you can tow with your vehicle. I attached an install video for you to check out as well. While this does clamp around the bumper supports it would not prevent them from still functioning in the event of an accident. The brackets...
    view full answer...

  • Trailer Hitch for a 2015 Buick Encore
  • The wiring for a 2015 Buick Encore is # C56216 and won't be an included item with the Curt Class-I trailer hitch # C11358. The reason wiring harnesses do not come with the hitch is because some vehicles already have a trailer wiring harness so we make them available separately. The hitch # C11358 will come with a complete hardware kit, instructions and a pin and clip. If you happen to need a ball mount and hitch ball, I recommend ball mount # C45520 and 2 inch hitch ball # C40018...
    view full answer...

  • Trailer Hitch Receiver and Wiring Recommendation for 2014 Nissan Frontier 4 x 4 Crew Cab
  • When it comes to a hitch for your 2014 Nissan Frontier 4 x 4 Crew Cab, I recommend going with the Curt Class III Trailer Hitch Receiver, # 13241. This hitch bolts directly to the frame of your Frontier and provides a towing capacity of 5,000 lbs and 500 lbs of tongue weight. I have attached an installation video for you. As for wiring, you will want to go with the T-One Vehicle Wiring Harness, # 118266. This harness provides the relays to activate the tow package along with the 7-way...
    view full answer...

  • Hitch Extender to Tow a Trailer with a 2005 GMC Sierra 2500 with Truck Bed Camper
  • First you will need to determine if the trailer hitch on your 2005 GMC Sierra 2500 is a 2 inch or 2-1/2 inch. Just measure the opening width to determine the size. I am assuming that the tailgate is down and/or the camper overhangs the back of the truck thus the need for an extension. I recommend an extension that is long enough to where the face of the receiver is flush with or a few inches recessed under the rear most part of the truck or camper, whichever extends out the furthest. If...
    view full answer...

  • How Does a Weight Distribution System Increase the Tongue Weight Rating of a Trailer Hitch
  • You ask a very good question. A weight distribution (WD) system that is properly tuned for the trailer weight and correctly installed will move some of the trailer tongue weight (TW) off the hitch and shift it forward to the tow vehicle's front axle. The hitch ball essentially becomes a pivot point - like the wheel of a wheel barrow when you lift the barrow's two handles. With some of the TW shifted forward a hitch then can, in many instances, handle more weight from the trailer tongue....
    view full answer...

  • Curt Hitch Recommendation for a 2015 Ford Transit
  • The correct hitch for a 2015 Ford Transit Connect is the part # C13167, the part # C13193 that you referenced is designed to the 2015 Fort Transit T150, T250, and T350. It sounds like you may have ordered the wrong hitch for the vehicle you have.
    view full answer...

  • Hitch Recommendation for a 2006 Chevy Cobalt
  • Based on the size of the food cart you have the only option I can recommend for you would be to install a hitch on your 2006 Chevy Cobalt like # 60808 or part # 60815 if you have an SS model and tow a small trailer. The dimensions of the food cart are too big to fit on a cargo carrier. The hitch I recommended comes with a ball mount and a pin and clip. For a ball you can use # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). You will need to check the coupler of the trailer...
    view full answer...

  • Can Factory D-Rings Be Installed Over the Curt Hitch 13567 on a 1995 Jeep Wrangler
  • If you have a set of D-rings that are currently installed where the Curt Hitch part # 13657 would install on your 1995 Jeep Wrangler you could install them over the mounting bracket of the hitch as long as you got the appropriate length Grade 5 or higher bolt to replace the hitch's install bolts.
    view full answer...

  • Hitch Recommendation for a 2007 Dodge Ram 1500
  • If Dodge says that the towing capacity for your 2007 Dodge Ram 1500 is 7,000 lbs then that is the heaviest trailer you can tow. A towing setup is only as strong as it's weakest component. If you were to install a hitch with a heavier capacity than what your vehicle has it would not allow you to tow a trailer above the capacity for the vehicle. If you can find a lighter trailer so that your setup weighs less than the capacity for your vehicle you could install the B and W Hitch part #...
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Dodge Grand Caravan
  • Draw-Tite trailer hitch # 36455 does indeed fit all models of the 2015 Dodge Grand Caravan. But if you want a model that does include the ball mount, pin, and clip, then you want Hidden Hitch model # 90169. Hidden Hitch and Draw-Tite are sister companies and the hitches are identical. The ball mount is not included with the Draw-Tite hitches because we pair the ball mounts with the Hidden Hitch models instead. If you are also interested in trailer wiring harnesses you can use # 118534.
    view full answer...

  • Can Hidden Hitch Trailer Hitch for a Cadillac SRX Tow a Car Trailer with 3,000 Pound Car on It
  • Hidden Hitch trailer hitch # 87573 has a gross trailer weight capacity of 4,000 pounds (5,000 when using weight distribution) and a tongue weight capacity of 400 pounds (500 with weight distribution). So this trailer hitch could handle your trailer as long as the combined weight of the trailer with the vehicle loaded on it does not exceed the hitch capacity. The other thing you will have to look at is the capacity of the vehicle. The hitch might be able to tow up to 5,000 pounds but...
    view full answer...

  • Hitch for 2014 Honda CR-V Capable of Carrying 3 or 4 Bikes
  • There are Class III hitches available for the 2014 Honda CR-V that have the 2 inch receiver opening, which would allow you to carry a 3 or 4 bike rack. There isn't a hitch with a larger receiver opening available for your CR-V. Of the available hitches, I'd recommend the Draw-Tite Class III hitch, part # 75742. You can see the install details and an install video by clicking the provided links. For a compatible bike rack, the Thule Hitching Post Pro, part # TH934XTR would be a high...
    view full answer...

  • Would a Hitch Extender Be Needed to Carry a Harmar Scooter on a 2011 Buick Lacrosse
  • The problem with hitch extenders is that they reduce the capacity of the hitch they are installed on by 50 percent. The Hidden Hitch part # 90242 that you referenced has a tongue weight capacity of 300 lbs, so if you were to use an extender you would now be limited to 150 lbs of tongue weight. When installed the hitch opening should be recessed behind your bumper about 4 inches, so most likely the carrier you have would not require more clearance, but you can measure it from the center...
    view full answer...

  • 2015 Ford Explorer Exhaust Hanger Makes Contact with Trailer Hitch
  • If there is no noise from the contact between the exhaust hanger and the hitch then you don't have to do anything. If there is noise or you just want some more space then there are some things you can do to create more space. I have included a link to a help article that covers the different methods you could employ. If all else fails then a muffler shop would be able to take care of the issue pretty easily since they have the tools and the know-how to work on exhaust systems. I doubt...
    view full answer...

  • Exhaust on 2011 Ford Taurus Rattles Against Trailer Hitch Going Over Bumps
  • The exhaust on any given vehicle could be able to move enough to make contact with a trailer hitch. If this happens there are some things that you can do to correct the issue. We have a help article on the subject that I have linked for you which includes the various ways that the issue can be resolved. If you go with Curt hitch # C12296 and plan on doing some towing then you can use ball mount # C45518. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer...
    view full answer...

  • Hitch Recommendation for a 2014 Ford Focus to Tow Small Trailer
  • We have everything you need so that your 2014 Ford Focus can tow a trailer. For a hitch I would recommend the Hidden Hitch part # 60290 as it has been confirmed to fit your vehicle and it includes a ball mount and pin and clip. I attached an install video for you to check as well. You will also need a hitch ball to complete the connection. For that you would want the part # 19256 for a 1-7/8 inch hitch ball or part # 19258 for a 2 inch hitch ball. For trailer wiring you would want...
    view full answer...

  • Rise and Length of Ball Mount Included with Hidden Hitch Class I # 60339 for 2015 Mazda 6
  • The Hidden Hitch Class I hitch, part # 60339 does indeed include the ball mount, which has a rise of 4 inches, and is 10 inches long, measured from the hitch pin hole to the hole where the ball installs. I've edited a diagram showing these dimensions for you. Since you'll be towing with your Mazda 6, I'd encourage you to check with your owner's manual to determine the towing capacity of the vehicle and be sure not to exceed that amount. To complete your towing set-up, you might need...
    view full answer...

  • Trailer Hitch Fit for 2015 Jeep Wrangler Willy Wheeler Special Edition
  • The Hidden Hitch 2-inch Class III hitch receiver you referenced, part # 87424, is compatible with your 2015 Jeep Wrangler Willy Wheeler Special Edition according to my technical contact at Hidden Hitch. I have linked the written instructions, a video and two helpful articles on hitch installations. If you will be towing you will need a wiring harness # 118416. This is a custom-fit plug-and-play harness that requires no cutting or splicing of wires in your new Willys. An install video...
    view full answer...

  • Is Draw-Tite Class I # 24755 for an Acura TL Capably of Carrying A Mountain Bike on a Bike Rack
  • The Draw-Tite Class I hitch you referred to, part # 24755 has a 200 lb tongue weight capacity. This means that no more than 200 lbs can be safely suspended from the hitch, therefore the weight of your bikes and the bike rack you use can't exceed that weight limit. The Thule Vertex, part # TH9028XT would be an excellent choice. The rack can carry two bikes up to 35 lbs each, and features an integrated cable lock to help deter theft. An available hitch pin lock is available as part # THSTL2....
    view full answer...

  • Will Curt Trailer Hitch Work On 1989 Chevrolet Camaro With Aftermarket Dual Exhaust
  • The Curt Trailer Hitch, part # C11117 is designed to fit the frame of your 1989 Chevrolet Camaro, but the manufacturer states it will not work with dual exhaust. I have attached the installation instructions you can check out. Since you said the exhaust is an aftermarket system, I cannot tell you that the installation would be successful on your Camaro. You can take a look at the instructions and also the frame on your Camaro to determine if the exhaust would interfere with the hitch.
    view full answer...

  • Trailer Hitch And Wiring Recommendation For 2011 Jeep Grand Cherokee
  • The Curt Trailer Hitch, part # C13065 is designed to fit your 2011 Jeep Grand Cherokee. This is a Class lll hitch and has a 2 inch receiver opening. I have attached a link to an installation video for this trailer hitch on a 2011 Grand Cherokee you can check out. The hitch is rated with a maximum trailer weight of 5,000 lbs and a maximum tongue weight of 500 lbs. You will want to check your owner's manual or with your dealership to make sure you do not exceed the towing or tongue weight...
    view full answer...

  • Hitch Recommendation for a 2004 Mitsubishi Endeavor
  • The Draw Tite Hitch part # 75163 that you referenced has been confirmed to fit your 2004 Mitsubishi Endeavor and would work great for you. I attached a link to an install video that details exactly how this hitch will install on a very similar Mitsubishi Endeavor as yours. I also attached a link to the install instructions. If you follow both of these as your guide you shouldn't have any problems. I attached a link to our returns policy page for you to check out as well.
    view full answer...

  • Hitch Recommendation for 2011 Jeep Grand Cherokee
  • Check out the Curt Hitch part # C13065. This hitch installs right up to the bottom of the rear fascia of your vehicle which will give it the best possible ground clearance. This is also a 2 inch hitch confirmed to fit your 2011 Jeep Grand Cherokee. When we installed this hitch on a similar 2011 Grand Cherokee as yours we found that there was a distance of 15 inches from the bottom of the hitch opening to the ground. If you plan on doing some towing you might be interested in etrailer...
    view full answer...

  • Hitch Recommendation for a 1993 Toyota Corolla Wagon
  • We have a hitch confirmed to fit your 1993 Toyota Corolla wagon, but the hitch # C11181 that you referenced is not the correct one. Instead you would want the part # C111283 as it has been confirmed to fit your vehicle. If you will be doing some towing, you will also need a ball like # 19256 for a 1-7/8 inch diameter or # 19258 for a 2 inch diameter. For trailer wiring use # 119178KIT. I have included instruction links for the wiring and hitch for you. If you will be using the...
    view full answer...

  • Trailer Hitch Recommendation for a 2011 Volkswagen Routan
  • When determining the overall towing capacity of a vehicle you must always go with the lowest rated component in the system as the overall capacity as a towing setup is only as strong as the weakest component. This is especially true if the weakest component happens to be the vehicle as that's the only component that can't be swapped out for a higher capacity component. The Hidden Hitch part # 87451 is confirmed to fit your vehicle and has more capacity than you will be able to use....
    view full answer...

  • How to Determine Ground Clearance on a 2015 Lexus IS 350 After Hitch Install
  • All of the hitches you referenced have about the same dimensions. We haven't had the chance to install any of them so while I can't give you the exact dimensions you are looking for I can help you determine it. From the mounting surface of all of the hitches down to the bottom of the hitch opening the hitches measure 9-1/2 inches. If you measure from the frame of your vehicle down 9-1/2 inches that is where the hitch will sit. From that point you can measure to the ground and you will...
    view full answer...

  • Hitch Recommendation for a 2011 Ford Edge
  • I would recommend the Hidden Hitch part # 87604. This hitch has an e-coat base and is powder-coated on top of that for superior rust prevention over other hitches that only have powder-coating. This hitch is also a Class III 2 inch hitch that will give you more towing capacities and accessory options than a 1-1/4 inch hitch. I attached an install video for you to check out as well. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It...
    view full answer...

  • Hitch and Tandem Bike Rack Recommendation for a 2012 Ford Focus Sedan
  • The bike rack you referenced is designed to fit 2 inch hitches. I do have solution for you, but there are no 2 inch hitches available to fit your vehicle. For a hitch you will want to use the # 24872 that you referenced. I attached an install video for you to check out as well. The only tandem bike rack we offer that would work with a Class I 1-1/4 hitch like the # 24872 is the RockyMounts Tandem TailPipe # RKY1031.
    view full answer...

  • Trailer Hitch Recommendation For 2015 Honda CR-V
  • We offer three Class lll trailer hitches that are designed to fit your 2015 Honda CR-V. I recommend the Hidden Hitch Trailer Hitch, part # 87621. This hitch has a 2 inch receiver opening. The distance from the center of the hitch pin hole to the back edge of the bumper on a 2015 CR-V is 2 inches. The Curt part # C13119 and the Draw-Tite part # 75742, both have the same measurements from the pin hole to the back of the vehicle but I like the 87621 because it costs a little less than...
    view full answer...

  • Trailer Hitch and Wiring for a 2001 Mercedes E-Class
  • There are 2 different hitches available for the 2001 Mercedes E-Class. Hitch # C11830 fits E320 station wagon models. And Curt hitch # C11744 is designed for sedan models. So you would just choose the hitch based on which version you have, station wagon or sedan. We haven't installed either hitch on a vehicle yet so we do not have videos or our own pictures. But I can link the instructions for you so you can see what is involved in the installation process. If you plan on doing some...
    view full answer...

  • Installation Instructions for Curt Trailer Hitch 13555 on a 2011 Honda CR-V
  • Take a look at the instructions I have linked for Curt trailer hitch # 13555. The torque specs will be located in step 4. I have included a link to a video showing an example installation for you as well. I have also included a link to our help article with hitch installation tips.
    view full answer...

  • Will Curt Hitch # C15300 Fit 1979 Ford F-150 Long Bed with Standard or Step Bumper
  • Yes, the Curt Class V trailer hitch you referenced, part # C15300, is a confirmed fit for your 1979 Ford F-150 long bed with standard or step bumper and 37-1/2-inch wide frame. Installation will require some drilling and temporary removal of the spare tire. An install video is linked for you. For a wiring harness you can use Draw-Tite # 18252 which provide a 4-pole flat trailer connector for your trailer lights. A great option in a ball mount kit is item # EBMK2416 which includes...
    view full answer...

  • Recommended Wiring Setup for a 2015 Chevy Colorado Crew Cab Without a Tow Package
  • I contacted Curt Manufacturing and even though your 2015 Chevy Colorado Crew Cab doesn't have a tow package, the wiring connection point will be up under the bumper area, near the spare tire. You will use the Curt custom fit wiring # C56515. This will give you the 5-way flat trailer connector to power your trailer's signal lights. If it's a 4-way connector then use Hopkins wiring kit # 41155. A mounting bracket such as mounting bracket 4-pole flat # 18144 is something to consider because...
    view full answer...

  • Increasing Fuel Tank Protection on 2001 Jeep Grand Cherokee
  • Chrysler's solution to increasing the protection of the fuel tank on the Jeep Grand Cherokee was to install a trailer hitch. I have included a link to all of the hitch receivers available for your 2001. My personal recommendation is to go with a Class III hitch like the Curt, # 13051. A Class III hitch not only gives you the added towing capacity but by having the 2" opening you increase your options when it comes to hitch mounted accessories.
    view full answer...

  • Recommended Trailer Hitch for Cherokee 2015 Latitude 2x4
  • The Curt Class III Hitch, part # C13172 is indeed a fit for your 2015 Cherokee Latitude. If you don't already have a bike rack, you can't go wrong with the Thule Hitching Post Pro, part # TH934XTR, which is a popular bike rack for our customers who own the 2014 or 2015 Cherokee. If you'll be transporting women's bikes or bikes with sharply-angled top tubes, you might also consider a frame adapter bar like part # 64005. The bar spans the distance between the handlebar gooseneck and...
    view full answer...

  • Does the Draw-Tite Class I Hitch # 24925 Have a Stop Punched Into the Receiver Tube
  • Hidden Hitch and Draw-Tite brand Class I hitches will all have the stop punched or welded into the receiver tube to prevent higher capacity Class II accessories from being used. This is intentionally done as a safety measure. Overloading the hitch can cause the receiver tube to bend or the hitch attachment points to the vehicle to fail. Curt offers a Class I, part # C11355 that doesn't have the stop in the receiver tube. This being said, only a Class I rated accessory should be used...
    view full answer...

  • Hitch Recommendation for a 1997 Oldsmobile 88 for Towing
  • For a hitch confirmed to fit your 1997 Oldsmobile 88 you would want the Draw Tite Hitch part # 36211. This hitch will attach to the frame of your vehicle and has towing capacities of 3,500 lbs total trailer weight and 300 lbs tongue weight. You will need to check the owners manual of your vehicle to determine the capacity for the vehicle and be sure not to exceed this figure. To complete your towing setup you may also be interested in the following products. Class II Drawbar 3-1/8"...
    view full answer...

  • Hitch Recommendation for a 2014 Toyota Camry Hybrid for Carrying Bike Rack
  • I have a solution for you, but since the Curt Hitch part # C12107 requires the use of a stabilizer strap like part # 18050 when used with a non-supported accessory like a bike rack I would instead recommend you go with the Draw Tite Hitch part # 36540 as it doesn't have the requirement.This way you won't have anything contacting any painted surfaces of your vehicle while carrying your bikes. The tech tips for this hitch install on your vehicle state that drilling is required for installation,...
    view full answer...

  • 2015 Nissan Murano Hitch Recommendation
  • The Hidden Hitch Trailer Hitch # 87679 that you referenced is a new hitch that has been confirmed to fit your 2015 Nissan Murano. It does not fit older models of the Murano, only the 2015. I confirmed this by checking with Hidden Hitch. The Hidden Hitch that fits the older Muranos is actually part # 87486. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a...
    view full answer...

  • Cargo Carrier Recommendation for a 2001 Ford Taurus with Draw Tite Hitch # 24699
  • The issue that you are running into is that the Draw Tite hitch part # 24699 that you referenced is a Class I hitch and the cargo carrier you bought is a Class II only accessory. That tab that you have found in the hitch is designed to prevent Class II accessories from being used in the hitch. This is so you don't overload the hitch. Realistically the only solution I can recommend for you would be to go with a Class I rated cargo carrier like the # C18145. Check out the review video...
    view full answer...

  • What Size Socket or Wrench Is Needed to Install Curt Hitch part # 13322
  • The install hardware that is included with the Curt Hitch part # 13322 that you referenced includes bolts that are M14-2.00. That size of bolt head calls for a 21 millimeter socket or wrench. I attached an install video for you to check out as well.
    view full answer...

  • Trailer Hitch Recommendation for a 2004 Volkswagen Jetta GLS
  • The reason the Curt Hitch part # C11070 that you referenced won't fit a GLI is because the GLI models have OEM ground effects. The GLS models do not have the ground effects so the # C11070 would fit. I attached an install video for you to check out as well. If you are looking to doing any light towing with your vehicle, I would also recommend these items listed below. Wiring Kit # 119178KIT 2 inch Hitch Ball # 19258 1-7/8 inch Hitch Ball # 19256
    view full answer...

  • Recommended Trailer Hitch and Ball Mount for a 2009 Chevy HHR
  • The trailer hitch I recommend is the Draw-Tite Class I # 24756 and Draw-Tite ball mount # 3594 because the top of the receiver to the ground is 10-1/4 inches and the ball mount will give you a 4-inch rise. As a result, giving you a 14-1/4 inch ground clearance and stay above the 13-1/2 inches. The weight will bring the clearance down a tad from the 14-1/4 inch clearance which will keep your trailer more level. The wiring for your 2009 Chevy HHR is # 118407 and 1-7/8 hitch ball is # 19256.
    view full answer...

  • Trailer Hitch for Carrying 350lb Dirt Bike in Hitch Mounted Carrier on 1999 Ford Explorer
  • The Curt Class III hitch you referenced, part # 13540 will indeed allow you to retain the full-sized spare in place under the rear of the vehicle. If the 350 lb figure you mentioned is just the weight of the bike, not including the carrier you'll be overloading the hitch. In that case, I'd recommend the Draw-Tite Class III, part # 75096 which has a 500 TW capacity and would also allow the spare tire to remain in place. Even if that 350 lb figure included the weight of the carrier, I'd...
    view full answer...

  • Hitch Mounted Options for Carrying 540lb Motorcycle with 2001 Nissan Frontier
  • Although we do offer tray-style motorcycle carriers, the 400-500 lb tongue weight capacity of the hitch, which is the maximum downward force that can safely be applied, would be exceeded by the weight of your bike. This would cause the hitch or its attachment points on the truck to fail while you're transporting the bike, which would be very bad. If your bike is smaller than a 750cc, a hitch mounted carrier like part # RHMC2 would be a good alternative if the tires on your bike are between...
    view full answer...

  • Hitch, Cargo Carrier, and Accessory Recommendations for 2014 Chevrolet Orlando 1LT
  • Yes, the Curt Class I Trailer Hitch Receiver, # C11278, is the correct hitch for your 2014 Chevrolet Orlando 1LT. Please keep in mind that Curt does require the use of Support Strap, # 18050, for all non-trailer loads including bike racks, cargo carriers and so forth. Failure to properly support these loads will void your hitch warranty from Curt. As for a cargo carrier, the 20x48 Pro Series Cargo Carrier, # 6500, with angled shank for added ground clearance is a great choice. In an...
    view full answer...

  • Clearance Issues with 2015 Subaru Outback with Hidden Hitch Trailer Hitch and Yakima Holdup 2
  • We have not yet taken that measurement but I can tell you how to determine the bumper clearance measurement. To determine if the Yakima Holdup Bike Rack # Y02443 will work on your vehicle when carrying bikes and folded on your 2015 Subaru Outback, the measurement from the center of the hitch pin hole to the farthest back portion of the rear bumper is needed. We installed the Hidden Hitch Trailer Hitch, # 87568, on a 2014 Outback and measured 4-1/2 inches from the center of the hitch...
    view full answer...

  • Class III Trailer Hitch Fit for 1997 Ford F-150 with Flareside Bed
  • Yes, the trailer hitch you referenced, Curt Class III # 13355, is indeed a confirmed fit for the 1997 Ford F-150 with flareside bed. This hitch bolts on with included hardware with no drilling required. You will need to temporarily lower your 20-inch (or smaller) spare tire for installation. If you have a larger spare then the hitch will not fit unless you relocate the spare. An installation video is linked for you. I did go to our warehouse to measure the hitch for you; its overall...
    view full answer...

  • Trailer Hitch Recommendation for a 2000 Toyota Tacoma
  • For a Draw Tite Hitch that has been confirmed to fit your 2000 Toyota Tacoma you would want the part # 75078. The part # 75031 that you referenced is designed to fit older Toyota trucks so I cannot recommend it for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch...
    view full answer...

  • Trailer Hitch Recommendation for a 2005 Subaru Forester
  • The difference between the Curt Hitches part # C120383 and part # C12038 is that the # C120383 comes with a ball mount that you would use for towing and the other hitch does not. Either hitch would fit your 2005 Subaru Forester. I attached an install video for you to check out as well. Then you will need to add a properly sized ball and the wiring. Those items are not included with the hitch. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring...
    view full answer...

  • Trailer Hitch Recommendation for a 2015 Volkswagen Golf
  • All of the hitches we offer for the 2015 Volkswagen Golf are confirmed to fit all models except for the R models. The Draw Tite hitch part # 24925 that you referenced will fit either a TDI or the gas models so it would be the one to use as long as you don't get the R model with the center exhaust. With that being said, I recommend the ball mount # C45016 as it fits 1-1/4 inch trailer hitch receivers. For a 1-7/8 inch hitch ball, go with # 19256. For a 2-inch hitch ball # 19258...
    view full answer...

  • Trailer Hitch Recommendation for a 2014 Ford Escape
  • The etrailer.com Ball Mount Kit part # 989900 does not include a wrench to tighten the hitch ball down. For a wrench to go with this kit you would want the part # 62342. For a trailer hitch the part # 87627 that you referenced would be the correct hitch to use. I attached an install video for you to check out as well. For trailer wiring you would want the part # 118566.
    view full answer...

  • Hitch Recommendation for a 2012 Dodge Ram 1500 without Factory Hitch
  • For your 2012 Ram 1500 without a factory hitch the correct part number for a Curt Class IV hitch would be the # 14374. The # 14361 is designed to fit older 1500 models so it would not work for you. I attached an install video for you to check out as well.
    view full answer...

  • What Vehicles does the Curt Hitch Part # C13149 Fit
  • The Curt Hitch part number # C13149 that you referenced will fit 2006-2015 Toyota RAV4s. When you sell the hitch you can have the person who buys it check out the link I attached for info on how to install it. If the install hardware has been used you will need to replace it with new hardware. For that you would need part # RHK. You will need to select Curt from the drop down menu on the product page and enter the part number in the box provided.
    view full answer...

  • Availability of Draw-Tite Class III/IV Trailer Hitch for 2015 Audi Q5
  • Draw-Tite has just released their Class III/IV # 75940 receiver hitch, so it is available for order. If you'll be towing with your hitch, you might need the following to complete your towing system: Ball mount, part # 2923 1-7/8 inch trailer ball, part # 19260 2 inch trailer ball, part # 63845 The trailer ball you need will depend on the coupler of the trailer you tow. The necessary ball size should be stamped into the coupler itself. You'll need to obtain the trailer wiring...
    view full answer...

  • Hitch Recommendation for a 2011 Mercedes Benz E350 Sedan
  • For your 2011 Mercedes E350 Sedan the only hitch we have available for it is the Curt Hitch part # C11001. This hitch has a 1-1/4 inch opening like you mentioned. 2 inch hitches are typically reserved for larger vehicles like SUVs and trucks. The only solution I have for you would be to get this hitch and then also upgrade to a bike rack and cargo carrier confirmed to fit this hitch size. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman...
    view full answer...

  • Confirming Trailer Hitch Receiver Fits for a 2015 Buick Lacrosse FWD
  • The Hidden Hitch Class II # 90242 and Draw-Tite Class II # 36538 are confirmed fits for your 2015 Buick Lacrosse FWD. The Hidden Hitch Class II # 90226 and the Draw-Tite Class II # 36522 you referenced will not fit your 2015 Buick Lacrosse FWD. Currently, the Hidden Hitch # 90242 will include a ball mount, pin and clip. The wiring you will need for either hitch is # 118497. If you go with the Draw-Tite I recommend the ball mount kit # EBMK4 which will include an interchangeable...
    view full answer...

  • Does Cross Member of a 2015 GMC Canyon Get Removed to Install Curt Hitch C13176
  • The factory cross member or hitch of your 2015 GMC Canyon will have to get permanently removed to install the Curt Hitch part # C13176 that you referenced. This hitch will replace the cross member and as long as you install it correctly your warranty would not be voided. You will be able to reinstall your spare tire with this hitch installed as well. There are safety chain loops on this hitch too. If you plan on doing some towing you might be interested in etrailer ball mount kit...
    view full answer...

  • Long Hitch Extension and High Capacity Hitch Recommendation for a Ford F250 Super Duty
  • Sounds like you are looking for a setup that will allow you to use a longer hitch extension than the 24 inch bar you are currently using without reducing your towing capacity. If you use the TorkLift SuperTruss Hitch Extension # TLE1536 which is 36 inch extension with a TorkLift SuperHitch Original # TLF1002 you will have the following capacities: Maximum gross trailer weight: 6,500 lbs. Maximum GTW when used with weight distribution: 12,000 lbs Maximum tongue weight: 650 lbs Maximum...
    view full answer...

  • How to Fix Exhaust Rattle After Trailer Hitch Install
  • This is a fairly common problem that has a fairly simple solution. What you will need to do is reposition the exhaust of your 2010 Chevy Traverse so that it is far enough away from the hitch that it will stop rattling against it. For more info on how to do this check out the help article and video I attached. Basically you will either have to bend the exhaust hangers slightly or use different length hangers.
    view full answer...

  • Hitch Recommendation for a 2016 Kia Sorento
  • The Curt hitch part # C13195 has been confirmed as a fit for your 2016 Kia Sorento so I would recommend it for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right rise or drop to tow the...
    view full answer...

  • Recommended Hitch for 2014 Honda CRV Carrying a Scooter Carrier
  • As long as your daughters 2014 Honda CR-V has the tongue weight rating to carry the weight of the scooter and the lift you could use a hitch like the # 75742 to carry the scooter carrier. This hitch has a tongue weight capacity of 350 lbs, you will need to consult the owners manual of the CR-V to determine what Honda recommends as the tongue weight capacity and be sure not to exceed the lower of the two figures. As long as you center the scooter on the carrier you wouldn't have to worry...
    view full answer...

  • Choosing Class II or III Hitch for 2006 Subaru Legacy Sedan
  • The Hidden Hitch Class III hitch, part # 87446 and the Class II model, part # 90138 both are a confirmed fit for the 2006 Subaru Legacy sedan model. The Class II hitch would provide slightly better ground clearance, by about 3/4 of an inch or so. Other than the different size receiver tube, either hitch would fit your Legacy equally well. Due to the much better selection of hitch mounted accessories like bike racks and cargo carriers, we customarily recommend folks go with the 2 inch...
    view full answer...

  • Recommended Trailer Hitch For 2011 Ford Escape
  • The Hidden Hitch, part # 87626, and the Draw-Tite, part # 75751, both are designed to fit your 2011 Ford Escape. They both measure 1-1/2 inch from the rear of the bumper to the hitch pin hole and both use the same mounting holes on the frame of the Escape. Since both hitches have the same weight rating and features I recommend going with the less expensive Hidden Hitch, part # 87626. Both are Class lll hitches and have 2 inch receiver openings. I have attached a couple of installation...
    view full answer...

  • Hitch Recommendation for a 2011 Buick Lacrosse CXL and CXS
  • Actually both the Draw Tite Hitch # 36538 and the Hidden Hitch part # 90242 that you referenced are made by the same company so they are basically identical. Either would work great for you. The Harmar AL160 is a scooter carrier, if the one you are looking at is confirmed to fit a 1-1/4 inch hitch it should work with either hitch previously mentioned. The weight of the carrier plus your scooter could not exceed 300 lbs otherwise it would be too heavy for either hitch.
    view full answer...

  • Does the Trunk Pan Shield Get Removed to Install Hidden Hitch 87755 on a 2007 Mercedes ML350
  • The installation instructions for the Hidden Hitch part # 87755 that you referenced say that if you want to reinstall the trunk pan shield you can trim it so that it is compatible with the hitch, but when we installed this hitch on a similar vehicle as your 2007 MB ML350 we just left it off. I attached a link to this video as well.
    view full answer...

  • Trailer Hitch for a 1996 Chevy S-10 with Roll Pan Bumper
  • We do have a trailer hitch for your 1996 Chevy S-10 with the roll pan bumper. it is Curt hitch # 13920. I have included a link to the installation instructions for you. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount...
    view full answer...

  • Is Heat Shield Trimming Required to Install the Curt Hitch part # C11681 on a 2015 Honda Accord
  • To install a hitch like the Curt Hitch part # C11681 that you referenced on your 2015 Honda Accord you will need to trim the heat shield. For more info on that check out the install video and installation instructions I attached.
    view full answer...

  • Highest Rated Hitch Recommendation for a 1997 Dodge Ram 3500
  • The highest rated hitch we offer for your 1997 Dodge Ram is the Curt Hitch part # C15300. The capacities for this hitch are 2,400 lbs tongue weight and 17k total trailer weight when used with weight distribution. It doesn't look like this hitch would have enough capacity for the trailer you plan to tow unless you can reduce the weight of the trailer by 1,000 lbs or so. You will need a weight distribution system though. To get the full weight capacity you would need a WD system will be...
    view full answer...

  • Recommended Trailer Hitch for a 2015 Toyota Sienna
  • Yes, there are several trailer hitches that will fit your 2015 Toyota Sienna Limited AWD. The hitch I recommend is the Curt Class III # C13105. It will have a 350 pound tongue weight which will be just fine for carrying a bike rack like the Swagman Trailhead # S63360 that has a 3-inch rise in the shank. I included a link to all the trailer hitches that will fit your 2015 Toyota Sienna (Class II and III) along with a couple installation videos and informative article.
    view full answer...

  • Towing Capacity For 2007 Subaru Impreza WRX
  • Per the instructions for the Curt Hitch, part # C11318, which is a Class l hitch, the tow hooks are removed and are not reinstalled on your 2007 Subaru Impreza WRX. The hitch has a 2,000 lb towing weight capacity, but you would need to either check your owner's manual or with your dealership to see what the vehicle is rated for. You do not want to exceed the vehicle capacity for tongue weight or towing capacity. Typically, a Class l hitch is used for carrying items like bike racks...
    view full answer...

  • Recommended Trailer Hitch for a 2014 Nissan Versa Note
  • I recommend the Draw-Tite I hitch # 24909 as the towing capacity is 2,000 pounds and will have a maximum tongue weight of 200 pounds. It's corrosion resistant and the fully welded steel construction ensures great strength and durability. A pin and clip is included with this Draw-Tite hitch # 24909 and if you plan on doing any light duty towing, I recommend the ball mount # 3592, 2-inch hitch ball # 19258 or 1-7/8 hitch ball # 19256 and wiring by Tow Ready # 118582. I would double check...
    view full answer...

  • Routing Power Wire to Install Curt # 56146KIT Wiring Harness on 2003 Mercedes-Benz C240 Wagon
  • When installing a powered converter like the # 56146KIT on a vehicle, people will run the power wire along the underside of the vehicle, by following an existing wiring harness as it runs under the vehicle up into the engine compartment. As the wire goes from the rear to the front of the vehicle, be sure to avoid anything that's moving like suspension or steering components or hot like exhaust components. I don't have specifics to offer you, but we have a helpful FAQ article that provides...
    view full answer...

  • Will Curt # C15300 Clear Flatbed on 1997 Ford F350
  • I spoke with my Curt representative, who tells me that the front face of the receiver would sit 10-3/4 inches rearward of the rear-most mounting hole. If you find the rear most mounting hole in the underside of the frame member and measure 10-3/4 inches rearward, it'll give you a good idea of how far back the face of the receiver would sit. I've edited a photo for you that shows this dimension.
    view full answer...

  • Recommended Trailer Hitch for a 2013 Honda Odyssey Pulling Fully Loaded Trailer with a UTV
  • The trailer hitch I recommend is the Hidden Hitch Class III # 87479 and it will have a maximum tongue weight of 350 pounds and gross trailer weight of 3,500 pounds. The wiring you need is # 118521, and ball mount kit I recommend is # EBMK4 which will include an interchangeable ball set, ball mount with 2-3/4 inch rise or 4-inch drop, pin and clip and a storage bag. With that said though, you will not want to exceed the 350 pound tongue weight because it could bend the hitch and potentially...
    view full answer...

  • Will Hidden Hitch Trailer Hitches Fit Both 2006 and 2015 Honda Odyssey
  • The 2006 Honda Odyssey will use either Hidden Hitch trailer hitch # 87479 (2 Inch Hitch Opening) or # 90153 (1-1/4 Inch Hitch Opening), and these are also the trailer hitches listed as fits for the 2015 Honda Odyssey, so yes, your Hidden Hitch trailer hitch should fit. To complete your towing package you will want custom wiring harness # 118521, and for a ball mount and hitch ball use # EBMK4. For install details and some product demonstration videos, click the provided links.
    view full answer...

  • Can a Harmar AL160 Scooter Lift be Carried by a 2011 Buick LaCrosse
  • I checked up on the Harmar AL160 scooter lift. It is pretty sweet. According to the specs the hitch height range is 5 to 18 inches. The trailer hitches for your 2011 Buick LaCrosse will be within that range so you would not have to change anything using that lift with a trailer hitch.
    view full answer...

  • Hitch and Wiring Harness Recommendations for 2014 BMW 3-Series 328d Sedan
  • The 1-1/4-inch Class I trailer hitch you referenced, Curt # C11367, is indeed a correct confirmed fit for the 2014 BMW 328d sedan. This light-duty hitch bolts on using included hardware and if desired it can be ordered with a ball mount for towing. For the 1-7/8-inch ball version order # C113671; for a 2-inch ball order # C113672; if you already have a hitch ball that fits your jet ski trailer coupler then you can order # C113673 that includes a standard ball mount. make sure you choose...
    view full answer...

  • Trailer Hitch Recommendation for a 2009 Isuzu Rodeo
  • The Hidden Hitch part # 70498 that you referenced has been confirmed to fit your 2001 Isuzu Rodeo as long as it has its spare mounted under the vehicle. If the spare is on the rear door you would instead want the # 87473. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch...
    view full answer...

  • Hitch Install Picture Request for a 2013 Cadillac ATS
  • We don't have a picture of the hitch part # 60361 installed on a vehicle like your 2013 Cadillac ATS, but the Curt hitch part # C11311 that has also been confirmed to fit your vehicle does have some install pictures in the installation instructions link that I attached. I attached those pics for you to check out as well.
    view full answer...

  • Hitch and Trailer Wiring Recommendation for a 2015 Subaru Forester
  • For your 2015 Subaru Forester either the Curt Hitch part # C13144 or the Hidden Hitch part # 87654 would work well for you. If it were me I would go with the one that costs less. Both hitches have the same capacities and will install in basically the exact same way. Since you do not have a factory trailer wiring you will need to start with a 4-way (if you do not have one). For that you would want the # C56040. From there you would need to convert the 4-way to a 7-way so that you...
    view full answer...

  • Stabilizer Strap Recommendation for Curt Hitch C13130 on a 2013 Acura RDX
  • The correct stabilizer strap to use with the Curt Hitch part # C13130 that you referenced is the part # 18050. To see how it would get used check out the review video I attached. Another option you have that might interest you is to use a Hidden Hitch like part # 87642. Hidden Hitch does not require the use of a stabilizer strap. I attached an install video for this hitch for you to check out as well. The most popular bike rack we carry that has been confirmed to fit this vehicle...
    view full answer...

  • Troubleshooting Vibration/Buzz at Idle After Trailer Hitch Install
  • It sounds like your exhaust may be rattling against the hitch when at idle. This is a fairly common problem that can be fixed pretty easily. Basically you will have to reposition the exhaust so that it is further away from the hitch and will no longer contact it at idle. I attached a help article and video for you to check out that will detail how to fix the problem.
    view full answer...

  • Replacement Hardware Recommendation for the Curt Hitch part # C12232
  • Yes we do, the part number you will need is # RHK. You will need to select Curt from the drop down menu and you will need to enter the part number C12232 in the part box and we will ship you out the correct replacement hardware.
    view full answer...

  • Hitch Lock and Anti-Rattle Device for Curt Hitch 13581 on a 2011 Mitsubishi Outlander GT
  • An anti-rattle hitch lock that uses a regular hex-head bolt should fit your Curt trailer hitch # 13581. Take a look at # SR25219. The head will be approximately 3/4 inches wide so measuring from the center of the hitch pin that would be 3/8 of an inch. If you have 3/8 of an inch from the center of the pin hole to the bar on your hitch then this lock would work. Another option is to use a regular hitch lock such as # 5201 and a stand-alone anti-rattle device like # BX88224.
    view full answer...

  • Can the Curt Stabilization Strap be Used on a Platform Style Kuat Bike Carrier
  • The Kuat NV, # N101 as an example, and the Sherpa, # S101 as an example, are platform style carriers that hold the bikes at the wheels and would not be the best bike racks when using stabilization strap # 18050 with a Curt trailer hitch # C11471 on your 2009 Hyundai Elantra. Curt does not provide instructions on how you would attach the strap to this type of bike rack so you would basically need to attach it anywhere that you could. The other option is to use Draw-Tite trailer hitch...
    view full answer...

  • Hitch Recommendation for a 2015 Subaru WRX
  • Yes, I spoke with my contact at Curt and the Curt Hitch part # C11408 that you referenced has been confirmed to fit the 2015 Subaru WRX so it will work for you. The hitch will hang below the rear bumper when installed. I attached a picture that shows this hitch installed as well. For a ball mount you would want part # C45521, 1-7/8 inch hitch ball # 19256, 2 inch hitch ball # 19258. For trailer wiring you would want the part # C56259.
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Subaru WRX
  • The Curt trailer hitch # C11408 will not be concealed behind the rear fascia of your 2015 Subaru WRX. The cross tube and receiver will be visible beneath the rear fascia. Take a look at the installation instructions I have linked that shows some pictures of the hitch position. If you plan on doing some towing the correct ball mount to use is # C45521. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # C56259. If you will be using the...
    view full answer...

  • Can a 2012 Hyundai Santa Fe Tow a Horse Trailer
  • Your friend will first to consult the vehicle owners manual of his 2012 Hyundai Santa Fe to see what the towing capacity is for his specific model. If the towing capacity of the vehicle and the trailer hitch used exceed the gross trailer weight then the Santa Fe would be able to tow the trailer. The Curt trailer hitch # C13073 is rated for 350 pounds tongue weight and 3,500 pounds gross trailer weight. Given the average weight of a horse this probably means that only one horse could...
    view full answer...

  • Is Threadlocker Needed When Installing TorkLift Superwinch Trailer Hitch Receiver
  • Loctite Threadlocker 243, like part # LT1330799 creates a strong bond that can still be removed with hand tools. It isn't required by the manufacturer for installing a hitch like the TorkLift SuperHitch Original Trailer Hitch Receiver, part # TLC1212. If torqued properly per the installation instructions, the hitch should be just fine.
    view full answer...

  • Dimensions of the Class 3 Hidden Hitch for a 1980 Jeep CJ-5
  • Absolutely! I went to our warehouse to provide you the measurement you are needing on the Class III Hidden Hitch # 87001. This hitch has a towing capacity of 3,500 pounds and tongue weight of 300 pounds. See the diagram I included as well. Please note that if you have a 20 gallon gas tank, the Hidden Hitch # 87001 will not fit. If your Jeep has the 20 gallon tank then you would need Curt hitch # 13412. On the trailer hitch # 13412, you would remove your aftermarket bumper to install....
    view full answer...

  • Trailer Hitch for Scooter and Lift for a 2011 Buick LaCrosse
  • If the rear of your 2011 Buick LaCrosse is 6-1/2 inches from the ground on the driveway incline then anything that extends out further then that would be even closer to the ground. Basically you can probably expect to scrape the ground with a carrier installed in the trailer hitch. The way around this would be if the carrier you use had a rise in the shank effectively increasing its ground clearance. Carrier # PS10401-10402 for example has a slight rise in the shank (4 inches) and would...
    view full answer...










Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com