Expert Answers about Trailer Coupler

• Is the Inner Tube Portion of Bulldog Gooseneck Coupler, Part # BD0289500300 Available Separately
• We do offer just the inner tube portion for Bulldog # BD0289500300 gooseneck coupler. That part # is BD1289050300. I do see that you have already ordered the entire gooseneck coupler, part # BD0289500300. Given that your original coupler could potentially have hidden damage or have been weakened by the accident, your decision to replace the entire unit is the right choice for safety reasons.
  view full answer...


• Channel for an Adjustable Lunette Ring Trailer Coupler
• The adjustable lunnete ring, # 63036 comes with the channel. The channel itself is not 6 inches wide. It is the outside diameter of the ring that is 6 inches. The channel width is approximately 3 inches. The nuts and bolts are included as well. I have linked a video review for you. I have also linked the channel brackets we carry. A six inch wide option is not available.
  view full answer...


• Availability of a 3 inch Ball Gooseneck Coupler
• The only style of 3 inch gooseneck coupler that we offer is the Redline Trailer Coupler # WF2. This coupler uses a steel pin to secure the hitch ball.
  view full answer...


• Availability of a Trailer Coupler that Fits a 3-1/2 Inch Wide Tongue
• If the trailer tongue in question is 3-1/2 inches round then you can use Bulldog coupler # BD028383. If you have a square or rectangular tongue then a 3-1/2 inch wide straight coupler is not available. You may be able to use a channel bracket like # BDAC3000300, weld it to the end of the tongue, and then use coupler # BDA200C0317.
  view full answer...


• Availability of 12,500-Lb Rated Brake Actuator Coupler with Reverse Lockout For Drum Brakes
• The largest weight capacity I would have for a brake actuator coupler for drum brakes with a reverse lockout feature is 8,000 lbs. I have two models available, one would be the Atwood Trailer Coupler, part # 83010, and the other is the Atwood Trailer Coupler, part # 83000. These actuators will fit a 2 inch hitch ball only. They will include a manual reverse lockout that permits backing of the trailer. Since the Titan Brake Actuator Coupler, part # T1735200, that you have referenced, has no r
  view full answer...


• Availability of Offset 5th Wheel To Gooseneck Adapter that Extends to 16 Inches High
• The Ranch Hitch Universal 5th Wheel to Gooseneck Adapter you referenced, part # AM3139 extends to a maximum height of 14-3/4 inches. There is not a Ranch Hitch Adapter that has a higher height adjustment. To determine the exact height adapter you need, Jack the trailer so that it is level, and then back the truck up as if you were hitching it. Measure the distance from the bottom of the pin box (not the king pin) to the top of the gooseneck ball. (See provided diagram). This distance is the
  view full answer...


• Availability of a 2 to 3 Foot Fold-Away Trailer Coupler Hinge with Attached Coupler
• If you are needed a coupler and tongue that is already attached to a fold away hinge, we have # FHPB3530301. This is a 3x3 bolt on fold-away coupler and it is 34 inches long. But if you are looking for a 2 to 3 foot extension to the tongue you have, you will need to have a qualified welder in a machine shop of shop that works on trailers fabricate an extension for you. The work should be professionally done if you go this route.
  view full answer...


• Is There A 2-5/16 Bulldog Coupler That Slides Over Hitch Ball
• We do have a variety of 2-5/16 inch trailer couplers available. For a coupler that would slide over or onto your hitch ball, we have the Bulldog Collar-Lok Coupler, part # BD028499. The Bulldog Collar-Lok Coupler is available for different types of trailers. For a square channel tongue, we have the Bulldog Collar-Lok Coupler, part # BD028444. For an adjustable channel mount, we have the # BD028630, and for a round tongue, you would need # BD028442. However all the Bulldog Collar-Lok Coupl
  view full answer...


• Are There Any A-Frame Trailer Couplers That Do Not Require Welding For Installation
• All of the A-Frame Trailer Couplers are a weld-on application. There is not a way to hookup a temporary coupler to tow the trailer. What you could do, like you said, is have a qualified welder come out and install a replacement coupler on your trailer. The other option would be to have a towing company trailer the trailer to a professional and have a new coupler welded on.
  view full answer...


• Availability of Straight Coupler Replacement for Titan Aero 7500 Brake Actuator # T4500600
• The Titan Aero 7500 brake actuator, part # T4500600, has a 2-inch ball and fits a 3 inch wide channel tongue. It has a weight capacity of 7,500 lbs. In a straight bolt-on coupler with a 2 inch ball that fits a 3 inch wide channel, the coupler with the highest weight capacity would be the Titan Leverlock Coupler - Adjustable Ball, part # T4845000. This coupler will only have a weight capacity of 5,000 lbs, which is lower than the 7,500-lb capacity on the Titan Aero 7500 brake actuator. Th
  view full answer...


• Replacement Shock and Push Rod for a Titan Model 60 Trailer Disc Brake Actuator
• It does sound like the shock is not returning. We do carry the part you need. It is Titan Shock Absorber for Model 60 Brake Actuators, # T2336200. The Titan Coupler, # T4819900, is for disc brake applications. If it were used on drum brake applications, the psi level would be too high. Also the brake lines and fittings normally used for drum brakes would not be large enough for disc brake applications. The push rod could also be in need of replacement. It is part # T2346300. When performing
  view full answer...


• Availability of an A-Frame Coupler that will Fit a 1-7/8 Inch Hitch Ball
• The only A-Frame couplers that I have for a 1-7/8 inch ball are the two Titan brake actuator couplers. The Titan A-Frame Brake Actuator- Multi-Fit Ball - Weld On - 6,000 lbs, part # T2492800, and the Titan A-Frame, Leverlock Brake Actuator - Adjustable Ball - Weld On - 6,000 lbs, part # T4845500. These are couplers that include a hydraulic brake actuator and will work on drum brakes. The couplers that are available for a 1-7/8 inch size hitch ball are all for a straight tongue trailer. Th
  view full answer...


• Availability Of Keyed Alike Locks For Bulldog Collar-Lok Coupler # BD028287 And Trailer Hitch
• If you are needing a lock for the Bulldog Collar-Lok Coupler w/ Low-Profile Latch, part # BD028287, and a lock for the hitch receiver on your vehicle that are keyed alike you can use the Deadbolt brand lock. For your Bulldog coupler you would have to use the Deadbolt Trailer Coupler Lock, part # 28012. This is a coupler lock with an inside width of 3-3/8 inches. I pulled the Bulldog coupler from our warehouse and measured the size of the lock pin that goes in the coupler. It measured 5/16 in
  view full answer...


• Availability of a Replacement Master Cylinder for a DICO Model 20 Trailer Brake Actuator
• I spoke with my contact at Titan and he stated that the Dico model 20 coupler is similar to the Titan model 20 actuators like # T4750720. We do have numerous replacement parts made specifically for the Dico model 20 actuator. Below is a list starting with a replacement master cylinder. Dico Replacement Master Cylinder for Model 10 and 20 Actuators, # 23744 Dico Replacement Cover for Model 10 & 20 Actuator, # 15070 Dico Actuator Hydraulic Connector Fitting, fits Models 10 and 20 Old Style,
  view full answer...


• Availability of a Flexible Brake Line for Use with a Fold-Away Trailer Coupler
• Since your existing brake line going to the brake actuating coupler on the trailer tongue is a hard line, it will need to be replaced with a flexible line, like # 18018-SF, at least to the point where the Fulton Fold-Away Coupler Hinge Kit, # FHDPB330301, is installed.
  view full answer...


• Do You Carry the Mounting Bolts for Lunette Right Part 1385
• We offer a complete hardware kit with all the nuts, bolts and washers for this lunette ring. The hardware kit is part # BLT716100. If you need a nose plate as well, you can use part # TNP716100. I have added links to these parts below.
  view full answer...


• Is There A 2-5/16 Inch Trailer Coupler With A 25,000 Lbs. Capacity That Fits A 3 Inch Channel
• The Bulldog Trailer Coupler, # BDA256C0317, is made to use with the Bulldog 3-Position Adjustable Channel Bracket, # BDAC3000300. This bracket has a inside width of 3 inches. Keep in mind that manufacturing tolerances allow for this bracket to be slightly wider or narrower. The only couplers I have with 25,000 lbs, capacity are the flat mount couplers like the Bulldog Cast Head Coupler, # BD4425000317, and the Wallace Forge Flat Mount Trailer Coupler, # FC25. The highest rated height adju
  view full answer...


• Do You Have Adapters to Convert a Gooseneck Trailer to a Fifth Wheel
• Yes, we have a couple different solutions that could solve your problem. Since you have a fifth wheel with rails already in your bed, I would suggest using a Gooseneck plate built for fifth wheel rails like Draw-Tite part # 49080. If you will be towing other fifth wheel trailers and need to keep your fifth wheel on the truck at all times and do not want to pull the fifth wheel on and off, we do have adapter tubes. If you have a round gooseneck coupler with a 4 inch outer diameter, you could u
  view full answer...


• Availabiltiy of a Gooseneck Coupler to Replace a Fifth Wheel King Pin On a Trailer Coupler
• We have the Gooseneck Coupler - 24K, Item # SM2516NP, that can be welded to a 4 inch square inner tube. This coupler does not come with the tube so you would have to remove the fifth wheel king pin from your coupler and weld the gooseneck coupler to the existing square tube or weld the coupler to another tube and install it after removing the existing coupler and inner tube. At this time we do not carry the replacement 4 inch square tubing for gooseneck hitches.
  view full answer...


• Availability of Brake Actuator Coupler Replacement Nylon Wear Pads
• We do have replacement pads for the actuator you were looking at. The pads are part # 10966 for the bottom side and part # 10965 for the top wear pad. They are meant to fit the Demco D10 actuators. If you can write back with a part or model number of your actuator, I may be able to find replacement parts for it.
  view full answer...


• Availability of Lunette Rings Smaller than 3 Inches
• We carry a 2-1/2 inch Lunette ring that has a four hole flat mount base, item # 63023. Other than that our Lunette rings are 3 inches. We do have other couplers that bolt to your trailer tongue. I have listed them below. Trailer Coupler 2-5/16 Adjustable (15,000 lbs) # 80281 Atwood Flat Nose Trailer Coupler, 25K # 75074 Wallace Forge Flat Mount Trailer Coupler, 25K # FC25 Flat Mount Trailer Coupler 2-5/16, 14K # FmC251614 Trailer Coupler 2-5/16 HammerBlow (12,500 lbs)
  view full answer...


• Do You Have a Coupler Lock for the Atwood Flat Nose Trailer Coupler
• At this time we do not carry a coupler lock that will work with the Atwood Flat Nose Trailer Coupler, item # 75074. If your trailer has a flat mount coupler that has 4-1/2 inch mounting holes, and is within the 25,000 pound weight capacity and 5,000 tongue capacity of the Atwood Flat Nose Coupler, item # 75074, then it will fit. This coupler requires a 2-5/16 inch ball.
  view full answer...


• Parts Available for Converting a Gooseneck Trailer for a Fifth Wheel Hitch
• We do have a couple adapters that will take your gooseneck trailer to a fifth wheel king pin. It is part # 2085205. The tube is 4 inches outer diameter round so if you have an adjustable gooseneck, this part will slip right in. If you have a square tube gooseneck, you could use part # KP84HB. This tube is 4 inches square.
  view full answer...