Expert Answers about Toolbox

Toolbox

Tool Box Recommendation for a 2006 Mitsubishi Raider That Fits Below the Rails
I have found several toolboxes that will fit your 2006 Mitsubishi Raider, however, the DeeZee Toolbox # DZ8748HDS is not one of them that will sit below your rails. The 3 series of toolboxes that should fit below your rails are DeeZee # DZ8537, # DZ8546, and # DZ9560, however, you will need to measure the bed of your truck to pick the right toolbox for you. The DZ8537 series is 37-1/8 inches long, 19 inches wide and 15-9/10 inches high. There is also a black version, # DZ8537B. I have a
view full answer...

Which Port to Use With DeeZee Transfer Tank # DZ91742
Yes, according to my contact at DeeZee, the port for the tank goes on the opposite port that you use to fill. The design of this unit allows you to choose which side is to fill and which side is to be used for the pump. I have attached a short video of a similar transfer tank that describes the fill port you are questioning.
view full answer...

Product Information for Dee Zee 38-Gallon Truck Bed Transfer Tank # DZ91752SB
The Dee Zee 38-Gallon Truck Bed Transfer Tank, part # DZ91752SB, will fit the 2007 Dodge Ram 3500 Pickup with 8-foot bed according to my contact at Dee Zee, but please note that this product is not designed for use as an auxiliary fuel tank to be connected to a vehicle fuel supply. It does not meet title 49 of the United States Federal Register governing transportation. However, my contact at Dee Zee did confirm that they do now offer tanks that are suitable for connection to a vehicle fuel s
view full answer...

How to Attach the RC Aluminum A-Frame Toolbox # 350970 to a Box Trailer Frame
You could use 1/4 inch self tapping screws with fender washers to secure the RC Aluminum A-Frame Toolbox, # 350970 to your trailer frame. It is important that you use screws that are long enough to penetrate the trailer frame when a washer is used. The recommended method for attaching a toolbox to a trailer frame is to use bolts, but your method will work as well. If you would rather use bolts, you could drill an access hole in the frame (I recommend the bottom of the frame) and use the fish
view full answer...

Which UWS Truck Toolbox Will Fit a 2005 Chevy Colorado
I checked the truck bed specifications for all cab versions of the 2005 Chevrolet Colorado and the inside width between the bed rails of all models is specified to be 57 inches. If possible I suggest you measure the vehicle to confirm. Also, keep in mind that many toolboxes are wider at the top section than at the lower section and this lower portion is what sits down inside the bed between the truck bed rails. We offer the DeeZee # DZ8160, which is a 7.1 cubic-foot aluminum toolbox, that
view full answer...

Does DeeZee Trailer Tongue Toolbox Has a Gas Strut to Assist Lifting the Lid
As you can see by the photo I obtained from DeeZee, the Trailer Tongue Toolbox, part # DZ91716 does indeed feature a gas strut on the lid to ease opening the lid.
view full answer...

Using DeeZee Wheel Well Tool Box In Front of Wheel Well on 2011 Dodge Ram
I spoke with my contact at DeeZee, who did not have any information as to whether or not the box would fit in front of the wheel well, rather than in its typical installation behind it. However, the foot or bottom of the box is 17 inches in length. If you have at least 17 inches of floor space between the rear of the wheel well and the front of the truck bed, the box should fit. (Make sure to allow for the thickness of the lip at the top of the bed.) If you should find that the box fits, yo
view full answer...

Will DeeZee Toolbox # DZ8170LB Fit a 2006 Ford F-150 XLT 5.4 Liter Triton Extended Cab
I checked with DeeZee and they do list toolbox # DZ8170LB as a fit for your 2006 Ford F-150 extended cab no matter what the bed size is. We always recommend measuring the truck bed in the area the box will go and comparing those measurements to the box dimensions as follows: Overall dimensions are 69-3/4 inches Long x 20 inches wide x 12-3/16 inches tall (13-3/16 inches tall counting the lid) Base dimensions are 60-3/4 inches long x 17-1/8 inches wide x 10-3/16 inches tall I have inclu
view full answer...

Can DeeZee Toolbox # DZ8760B Be Installed on a 2011 Ford F-350 without Drilling
If you could find the right kind of clamps you may be able to clamp it to the truck bed but you would still have to at least drill into the box, but not the truck. The ideal and safest way is to bolt the box into place.
view full answer...

metal box
The closest box we have to the measurements you are looking for is DeeZee box, # UB1416-24. It is 24 inches long, 14 inches tall, and 16 inches deep. It is black and made of steel. The door opens down.
view full answer...

Truck Bed Toolbox for 2012 Nissan Frontier SV
I checked the UWS online fitguide, and found that they do not list a toolbox that is a fit for the 2012 Frontier. We carry DeeZee truck boxes,and their fitguide lists the # DZ6160NB as being a fit for your truck. I would recommend measuring your truck bed and comparing your dimensions to those shown on the photo I have edited for you to ensure that the # DZ6160NB is a fit for your truck.
view full answer...

Will DeeZee Specialty Series Wheel Well Toolbox, # DZ95D, Fit a 2013 Toyota Tundra Platinum
To determine if the DeeZee Specialty Series Wheel Well Toolbox, # DZ95D, will fit your 2013 Toyota Tundra, you will need to go by the measurements of the box. I have included a picture showing the dimensions for you. It is 8-1/2 inches wide, 20-1/2 inches front to back, and 18-7/8 inches tall. Compare this to the space available in your truck to determine fit.
view full answer...

Will DeeZee Wheel Well Toolbox Fit a 2012 Dodge Ram 2500 Short Bed
DeeZee does list wheel well toolbox, # DZ956, as a fit for the 2012 Dodge Ram short bed models with or without the crew cab. To be sure you can compare the measurements in the picture I have provided with the available space in your truck bed. This box can be used on the driver or passenger side.
view full answer...

Availability of Metal Tool Box That Measures 30 Inches Long by 10 Inches Wide by 10 Inches Tall
I have some metal tool boxes that will measure close to the 30 inches long by 10 inches wide by 10 inches deep, but nothing that will have those exact measurements. I am listing below the tool boxes that will be closest in size to the dimensions of 30 inches by 10 inches by 10 inches. DeeZee Silver Toolbox, part # DZ74, measures 30 inches long x 20 inches wide x 18 inches tall. DeeZee Silver Toolbox, part # DZDB-2030, measures 32 inches long x 14 inches wide x 16 inches tall. DeeZee Blac
view full answer...

Height of DeeZee Truck Bed Transfer Tank DZ91752SB Including Vented Cap
The vented cap will add 3-1/2 inches to the height of the # DZ91752SB transfer tank, so it would be 22-1/2 inches tall including the cap. This transfer tank is also available in black aluminum, part # DZ91752B. See the included diagram for reference.
view full answer...

Construction of RC Industries Z-Series Underbody Truck Toolbox # UB1416-24
The RC Industries Z-Series Underbody Truck Toolbox you mentioned, part # UB1416-24 is constructed of 14 gauge powder coated steel. The T-Handle is constructed of stainless steel.
view full answer...

Will TruXedo TonneauMate Truck Bed Toolbox Fit 2002 Ford F-250 Extended Cab Short Bed
We do have a TruXedo TonneauMate Truck Bed Toolbox that will fit your 2002 Ford F-250 Extended Cap Short Bed pickup, but the one you referenced is custom-made for a newer truck. The correct kit for your vehicle is the # TX1117416. The toolbox measures 55 inches by 22 inches by 15 inches. I recommend measuring your truck bed to ensure a proper fit. I have included a link to the installation instructions for this item. This product will not fit flareside, stepside, or composite beds.
view full answer...

Will 48 inch Sheets of Plywood Fit in a Truck Bed that has DeeZee Wheel Well Toolboxes
In order to determine if you will still have enough room to haul a 48 inch wide piece of plywood you will need to measure the width of your truck bed. You will want to measure from inside of the bed rails. And since each of the DeeZee Specialty Series Tool Box # DZ94 and the driver side tool box # DZ95 are 7-3/4 inches wide you will need to subtract 15-1/2 inches from the width you measured previously and if that is more than 48 inches you will know if you will be able to carrry 48 inch wide ply
view full answer...

DeeZee Tool Box Recommendation for a 2012 Toyota Tacoma Crew Cab
I checked with DeeZee and they recommend the DeeZee Hardware Series Truck Bed Toolbox # DZ8160NB as a fit for your 2012 Toyota Tacoma. The dimensions of this box are 60 inches long by 20 inches wide and 12-1/5 of an inch tall. I would still recommend you check the measurements of your bed to be sure this box will fit.
view full answer...

How Secure is Attachment Method of DeeZee Red Label Chest-Style Toolbox # DZ8556
A chest type toolbox like the DZ8556 would be attached to the truck bed using the included sheet metal screws through the bottom of the box into the truck bed itself. Be sure to take care when drilling the holes so as not to damage the fuel tank, brake lines or any other components that might be located under the truck bed. If you wish, you can use bolts instead of the sheet metal screws for added security.
view full answer...

DeeZee Toolbox for a 2009 Toyota Tacoma with Bed Rail System and 6 Foot Bed
I spoke with my contact at DeeZee and toolbox # DZ8160 fits all models of the 2009 Toyota Tacoma with the 6 foot bed. It should not interfere with the the bed rail system but also it will not utilize it for installation. The overall width left to right at the top is 60 inches. At the bottom below the rails it is 51 inches left to right.
view full answer...

Compatibility of TruXedo TonneauMate Truck Bed Toolbox with 2003 GMC Sierra 1500
According to my contact at Truxedo, their TonneauMate toolbox, part # TX1117416 is indeed compatible with your 2003 GMC Sierra, unless you have a flareside, stepside or composite bed. If your truck has the GM Cargo Management System, which is the factory installed tracks along the top edge of the bed side, you will also need a clamp kit, part # TX1117458.
view full answer...

Will UWS Crossover Toolbox # UWS00404 Fit a 2013 Toyota Tacoma Double Cab Short Composite Bed
To determine if UWS toolbox # UWS00404 will fit your 2013 Toyota Tacoma you will need to compare the box measurements with the available space in the truck bed. The box dimensions are on the product page below the description and I have included a picture as well. The crossover toolbox comes with J-hook bolts that will secure it to the side rails of the truck bed. If your truck has the bed rail system it may interfere with the J-hook method of installation. In that case you may need to use th
view full answer...

Will UWS Truck Bed Chest - Wedge Series 12 Cu Ft, Part # UWS01040, Fit a 2005 GMC Sierra
UWS does not specify a fit for this toolbox with your 2005 GMC Sierra. I have attached a measured drawing of this toolbox that you can use to double-check the potential fit in your Sierra. Your provided bed width measurement of 63-3/4 inches suggests that this item will potentially work, but you will want to review and compare all dimensions beforehand to ensure a suitable fit, from both safety and appearance perspectives. Since this toolbox is not a specified fit for your Sierra your mou
view full answer...

Will UWS Toolbox, # UWS00404, Fit a 2012 Toyota Tacoma Double Cab
The UWS toolbox, # UWS00404, is listed as a fit for the 2012 Toyota Tacoma Double Cab. We always recommend taking a look at the box dimensions, see picture I have included, to ensure proper fit. Because of the size of this item, it ships via a freight service. Use the pull down menu under the shipping special box on the product page to determine the freight cost. You can also call customer service at 800-298-8924 for additional and more specific information.
view full answer...

What are the Dimensions of UWS Chest Toolbox UWS01049 Not Counting the Lid
The overall side to side width of the UWS toolbox # UWS01049 not counting the lid, is 36 inches. The front to back measurement is 19-1/4 inches. The height is 12 inches. Add an inch to that to account for lid clearance. I have included a drawing of the dimensions.
view full answer...

Tongue Mounted Tool Box Used on V-Nose Trailer
As long as there is some of the trailer A-frame exposed and the sides of the box would not extend too far past the trailer frame so that it could hit the tow vehicle during sharp turns, there is no reason why you could not install the box on the A-frame of your V-nose trailer. You would also want compare the dimensions of the box to the available space on the trailer tongue to ensure that the box does not interfere with anything else installed on the trailer tongue, like a jack or a weight distr
view full answer...

UWS Crossover Toolbox Fit for a 2005 Toyota Tacoma Regular Cab
The UWS Deep Truck Bed Toolbox, # UWS04545, is confirmed to fit your 2005 Toyota Tacoma regular cab. This toolbox will sit on the top of your truck bed walls and secures using j-hooks that grab the underside of the top of the truck bed wall. I have attached an image of the dimensions of this toolbox so you can compare them to the space available in your truck bed to be absolutely certain that you will not have any fit issues. If you have a bed liner that covers the underside of the top of th
view full answer...

Will UWS Truck Bed Toolbox Fit on 1996 GMC 1500 C/K Series Stepside Truck
The UWS Truck Bed Toolbox #UWS00080 will fit your 1996 GMC 1500 C/K Series Stepside truck. Made in the US, this toolbox is 54 inches long by 19-1/4 inches wide by 13-1/2 inches deep for a volume of 6.4 cubic feet. I have included a link to a video review of this product. You also might be interested in the UWS Toolbox Rubber Mat Liner # TOOLBOXLINER, which lines the inside of your UWS toolbox to minimize damage to and shifting of equipment. It is 61-1/4 inches long by 16-3/4 inches wide and c
view full answer...

Tray Options for UWS Aluminum Crossover Toolbox # UWS01015
For the UWS Aluminum Crossover Toolbox # UWS01015, we offer the UWS Aluminum Tool Tray # UWS060028. It is custom-made for the toolbox you referenced, which is 19-1/4 inches wide. The tray is 18-1/2 inches wide by 16 inches long by 1-1/2 inches deep, including the lip. Please be sure to compare the box measurements shown on the product page to the actual measurements of your truck bed to confirm the fit. I also recommend the UWS Rubber Mat Liner # TOOLBOXLINER, which line the inside of your to
view full answer...

Will DeeZee Wheel Well Toolbox # DZ95D Fit 2012 Ford F-350 Super Crew Long Bed Carrying 4x8 Plywood
After doing some research, I have found that 2 DeeZee Wheel Well Toolboxes # DZ95D will fit in the bed of your 2012 Ford F-350 Super Crew Long Bed with enough room for 4 foot by 8 foot sheets of plywood with room to spare. The bed width of your truck is 79.9 inches and each toolbox has a width of 8.5 inches for a combined width of 17 inches, so with both toolboxes and the sheets of plywood, you should have approximately 14.9 inches of space remaining in your truck bed. The drawers of this too
view full answer...

Fifth Wheel Compatible Toolbox for 2012 Ford F350 SD with 8 Foot Bed
According to UWS, the # UWS01040 is compatible with a 2012 Ford F350 SD with 8 foot bed. At 17-1/4 inches high, this chest-style box will not extend above the side of the bed rails, and would therefore not interfere with a properly installed fifth wheel hitch. I would recommend comparing the measurements shown for the toolbox on the product description page with actual measurements taken of your truck bed to make sure that the 20 inch front-to-back thickness of the box will not interfere
view full answer...

Will UWS Chest Style Toolbox Fit Beneath the Tonneau Cover on a 2010 Nissan Frontier SE
To determine if the UWS chest style toolbox, # UWS01026, will fit under the tonneau cover of your 2010 Nissan Frontier, you will need to measure. The overall height of this box is 17-1/4 inches. Measure from the bed up to the bottom of the tonneau cover to determine if 17-3/4 inches is short enough to fit under the cover. I have included a picture with the box measurements for you.
view full answer...

Is the Transfer Tank Included with # UWS03507 Baffled
I have just spoken with my UWS representative, who confirmed that the transfer tank included with part # UWS03507 is indeed baffled to minimize the movement of the liquid. Keep in mind that the transfer tank is meant to transport Diesel fuel or non-potable water, not gasoline.
view full answer...

Truck Bed Chest Recommendation for 2001 Ford Ranger Flare Side Short Bed
Based on my research, the UWS Truck Bed Chest # UWS01043 is a compatible fit for your 2001 Ford Ranger Flare Side (step side) short bed truck. The tool box is 36 inches long and the truck bed is 43.9 inches wide. I have included a picture showing these measurements. I also recommend the UWS Rubber Mat Liner # TOOLBOXLINER, which lines the inside of your UWS tool box to minimize damage to and shifting of equipment. I have included a link to a review video for this product.
view full answer...

DeeZee Toolbox Recommendation for a 2012 Ram 2500 Laramie Mega Cab with Regular Bed
I spoke with my contact at DeeZee and she stated that they have not had any fit issues of their DeeZee toolboxes with the Mega Cab model of your 2012 Ram 2500 Laramie. The DeeZee Red Label Toolbox, # DZ8560, that you referenced is the correct toolbox for your truck. This toolbox will fit trucks with the 8 ft or 6-1/2 ft beds. DeeZee also offers a slightly smaller Red Label toolbox, # DZ8556. This toolbox has the same height and width as the other toolbox, but it is 4 inches shorter at 56 inch
view full answer...

Will Chest Toolbox # UWS01044 Fit a 2011 Nissan Frontier Crew Cab with Utili-Track System
Chest style tool boxes like # UWS01044 for the 2011 Nissan Frontier are designed to be installed directly to the bed of the truck. It is not made specifically for a truck with the Utili-track system so if the system runs all the way from the front of the bed floor to the back then installing this box would cover part of the track. You would need to provide your own hardware to secure the box to the truck bed. You will need to drill through the bottom of the box and truck bed and use nuts and
view full answer...

How to Install a UWS Chest Style Toolbox in the Truck Bed of a 2011 Nissan Frontier
The best way to secure the UWS Truck Bed Chest, # UWS01043, would be to drill through the bottom of the box, through the truck bed, and then use nuts, bolts, and washers obtained locally to secure the box to the bed. You will also want to seal the holes using a sealant like # 0160297. While drilling through the truck may not sound desirable, securing it in this manner will allow the box to remain stationary and not damage the inside of the bed. When drilling be careful not to drill through an
view full answer...

Rear Door Clearance of # UWS00369 Tool Box on 2011 Ford Ranger XLT 4X4 Supercab 4 Door
According to my contact at UWS, the box will not interfere with the rear doors opening. The lid is 60 inches wide, you can confirm that the doors will clear by opening both rear doors, and measuring their distance apart right at the top of the bed. If this distance is more than 60 inches, the doors will clear the box with no problem. The photo I edited for you will show you where to take the measurement.
view full answer...

Will UWS Crossover Toolbox # UWS00419 Fit a 1996 Toyota Tacoma Regular Cab
The UWS toolbox # UWS00419 is listed as a fit for the 1996 Toyota Tacoma Regular Cab. I have included a link to a video review of this box for you. I have also included a video showing a typical installation of a crossover style toolbox that should help.
view full answer...

How to Mount a Chest Style Toolbox in the Bed of a 2011 Ford Ranger
On the chest style toolboxes like # UWS07280 you will need to use hardware of your choosing and drill through the bottom of the box and the truck bed to secure the box. Careful not to drill through anything important on the other side of the bed. Use a silicone sealant around the drilled holes to keep out moisture.
view full answer...

Will the UWS Deep, Angled Truck Bed Toolbox # UWS04548 fit a 2013 Toyota Tacoma Double Cab
The 2013 model Toyota Tacomas were unchanged from the 2012 models so the UWS Deep, Angled Truck Bed Toolbox # UWS04548 will work for you.
view full answer...

What Size Holes Need To Be Drilled For Installation of UWS Truck Bed Toolbox # UWS04547
The UWS Truck Bed Toolbox, part # UWS04547, you have referenced, will come with the J-bolt mounting hardware for installation. It includes two J-bolts, one for each side. The diameter of the J-bolts are 1/4-inch. When installing the J-bolts, the drilling is on the toolbox and not the truck itself. You will want to drill a minimum hole diameter of 1/4-inch to install the J-bolts. A little larger hole of 3/8-inch would work better and allow extra clearance for the bolt to fit through the toolbo
view full answer...

Will UWS Angled Truck Bed Toolbox # UWS00419 Fit Truck Bed With a Bedliner
The UWS Angled Truck Bed Toolbox, part # UWS00419, you have referenced, should fit a truck bed that has a bed liner, but you might want to measure the width of your truck bed to make sure. You would need 48 inches from the edge of bed across to opposite edge of bed for part # UWS00419 to fit. I would also measure the width from the inside front portion of the front of the bed to the front part of the wheel well. You will want to make sure there is at least 17 inches of clearance for the box t
view full answer...

DeeZee Specialty Series Narrow Toolbox for a 2004 Dodge Ram 1500 Quad Cab
According to DeeZee the correct Specialty Series Narrow Toolbox for your 2004 Dodge Ram 1500 quad cab is part # DZ6170NB. The base of this toolbox measures 60-3/4 inches long. I recommend measuring between the truck bed side rails to see if you have enough space to fit the base of the toolbox between the side rails. The top of the tool box that sits on the side rails measures 69-3/4 inches long. The DeeZee toolbox, # DZ6160NB, that you referenced is a smaller toolbox that was designed for tru
view full answer...

Fit of UWS Truck Bed Toolbox # UWS00436 on 2012 Ford F150 Crew Cab with 65 Inch Bed
The 69x19-1/4x17-1/2 inch dimensions of the UWS # UWS00436 truck bed tool box should allow it to fit in the bed of your 2012 F150 Crew Cab with the 65 inch bed, which I have confirmed by speaking with my UWS contact by phone. I would confirm this by making sure you have at least 58 inches of width between your bed rails. For specific information regarding shipping rates and times, please call 800-298-8924 and speak with one of our Customer Service folks. They would be much better able to a
view full answer...

Will DeeZee Crossover Tool Box # DZ8170DLB Fit a 2012 Ford F-150 Crewcab 5.5 Foot Bed
The DeeZee toolbox you referenced, # DZ8170DLB, is not listed as a fit for a 2012 Ford F-150 with 5.-1/2 foot bed. You would have to go by the measurements to determine fit. Since you have measured and found that it is not likely to fit you would need to go with a different box. The UWS toolbox # UWS0619 measure 17 inches front to back at the lower part of the box, see picture. It is listed as a fit for your 2012 Ford F-150, short bed. Take a look at the picture and compare the measurements t
view full answer...

What are the Dimensions of the Drawers in UWS Chest Toolbox # UWS01070
I spoke with my contact at UWS about chest style toolbox # UWS01070. She stated the draws are 2 inches deep by 4-3/8 inches wide by 19 inches long. The top lid does have to be opened to open the bottom door.
view full answer...

Will UWS Crossover Toolbox # UWS00375 Fit a 2000 Chevy Silverado
The UWS Toolbox, # UWS00375, is listed as a fit for a 2000 Chevy Silverado, short bed, excluding step-side models but it can also be used in a long bed. For any toolbox, check the measurements, see picture I have included, and compare them to your truck bed to ensure fit.
view full answer...

Can the UWS Secure Lock Series Toolbox # UWS06201 Open for Both Sides
The UWS Secure Lock Series Toolbox, # UWS06201, can be opened from one side or the other. There is a rod connector between the handles that engages both handles when one is turned. There is a lock on the drivers side only.
view full answer...

Installation of DeeZee Trailer Tongue Tool Box # DZ91716
The DeeZee Trailer Tongue Tool Box does not feature pre drilled holes, but the included sheet metal screws can be used to secure the box to the trailer tongue. The instructions call for 3/16 inch holes to be drilled through the bottom of the box into the trailer frame. Make sure you avoid any wires that might be running along the trailer frame. You can see the installation instructions by clicking the provided link. You could use u-bolts if you wish.
view full answer...

How does the UWS Topsider Style Side Rail Toolbox Install on a 2005 Toyota Tundra
The UWS Side Rail Toolbox, # UWSPGTS, bolts to your truck bed side rail and comes with legs that will bolt to the floor of your truck bed. All of the installation hardware is included with the toolbox. This toolbox comes in four different lengths of 48 inches, 60 inches, 72 inches and 90 inches. On the product page you can choose the length of the toolbox that you want to order.
view full answer...

Can you Transport Diesel Fuel with the DeeZee Specialty Series Truck Bed Transfer Tank
Yes, you can transport diesel fuel with the DeeZee Specialty Transfer Tank, # DZ91747. This tank was designed to carry diesel fuel only. Gasoline and other flammable liquids should not be transferred with this tank.
view full answer...

How Much Clearance is Required Between the UWS A-Frame Trailer ToolBox and the Trailer Body
I went out into our showroom and found a UWS A-Frame Trailer Toolbox # UWS01039 and measured the distance from the back of the box to the furthest point out with the lid open and found that you will need to have the box spaced 2 inches from the trailer body so that the lid will open without interference.
view full answer...

Size and Thread Pitch of the Drain Plug on a UWS Truck Bed Transfer Tank and Chest Combo
The bolt size for the drain plug on UWS transfer tank toolboxes like # UWS07330 is 3/4 inch. There are approximately 16 threads per inch but the threaded part is only 1/2 inch long. It is coarse threaded and not fine threaded.
view full answer...

Will UWS Truck Bed Chest # UWS07310 Fit a Cargo Carrier With Inside Dimensions of 19-1/2 x 58-3/4
I would recommend to use the DeeZee Truck Bed Toolbox, part # DZ8546S, on your cargo carrier. This toolbox has an overall dimension of 46-1/2 inches long by 19 inches wide. It has a little smaller interior capacity (8 cubic feet to 11.8 cubic feet) compared to the UWS Truck Bed Chest, part # UWS07310, but it will fit inside your cargo carrier. The overall dimensions on the # UWS07310, are 60 inches long by 20 inches wide. This toolbox would be too big to fit your cargo carrier that has inside
view full answer...

Fit of UWS Crossover Truck Toolbox # UWS00420 on 2012 Toyota Tacoma Access Cab
According to UWS, the # UWS00420 Crossover Truck Toolbox you referenced is a fit for the 2012 Toyota Tacoma Access Cab. The box is designed to fit truck beds that are at least 55 inches wide. Just to be certain, I would recommend comparing the dimensions of the box (see diagram) to the available space in your truck bed.
view full answer...

DeeZee Double Wheel Well Toolbox for a 2012 Dodge Ram 3500 Long Bed
According to DeeZee the Specialty Series Double Wheel Well Toolbox for your 2012 Dodge Ram 3500 Long Bed, is the Double Wheel Well Toolbox, # DZ956. This toolbox was designed to fit the dimensions of your truck bed. I have attached a diagram of the measurements for this toolbox for you to check out. The difference between toolbox # DZ956 and # DZ958 is that the # DZ956 is a little over 15-1/2 inches shorter than toolbox # DZ958. I have attached a photo of toolbox # DZ958 so you can compare th
view full answer...

Will Bed Liner have to Be Trimmed to Install a Crossover Toolbox on a 2012 Toyota Tacoma Double Cab
The UWS toolbox # UWS04546, is listed as a fit for the 2012 Toyota Tacoma Double Cab. Crossover toolboxes attach to the truck bed side rails with j-bolts like in the video I have linked. You will need to trim the bed liner where the j-bolt needs to attach to the truck.
view full answer...

Will UWS Black Crossover Toolbox # UWS04546 Fit a 2012 Toyota Tacoma TRD Access Cab with Bedliner
UWS toolbox # UWS04546 is listed as a fit for your 2012 Toyota Tacoma Access Cab. The box measures 63 inches wide, 17 inches deep at the bottom, and 40 inches wide at the bottom. The box is 20-1/2 inches tall overall. Compare these measurements to your truck bed to ensure fit. This toolbox mounts to the truck using j-bolts like in the video I have linked. If the bedliner is a drop in type then you will need to drill through it or cut away an area for the j-bolt. If it is a spray-in liner then
view full answer...

What is the Best Way to Install a Chest Style Toolbox in a 2009 Ford F-250
For chest style toolboxes like # UWS01020 you will need to drill through the bottom of the box and the truck bed and then use the hardware of your choice to bolt the box to the truck bed. Then you would use silicone to seal up the holes. You need to be careful when drilling through the truck bed not to drill through any components on the other side of the bed.
view full answer...

Will a Truck Bed Fender Well Toolbox Fit a 2011 Ford F-150
In the case of a fender well toolbox like # UWS01624, you will need to go by the measurements on the product page since your 2011 Ford F-150 is not listed. I have included a picture that shows the measurements for you to view.
view full answer...

Comparison of Steel and Aluminum Truck Bed Toolboxes on 2012 Ford Super Duty
Most of the newer truck tool boxes are made of bent sheet aluminum. The aluminum sheet features a rugged Diamond Plate pattern. The Diamond Plate aluminum is durable, lightweight and looks very tough. The aluminum sheet will not rust or deteriorate. Steel was used in many of the older toolboxes and is still used today. A steel toolbox is heavier than aluminum, but it is not always a drawback. Steel toolboxes are used because it is tougher and will resist more dings and dents if you transpor
view full answer...

Replacement Fuel Cap for the UWS 45-Gallon L-Shaped Transfer Tank and Chest # UWS06019
The UWS Replacement Fuel Cap, # UWSCAPS, is the replacement fuel cap for the UWS 45-Gallon L-Shaped Transfer Tank and Chest, # UWS06019, that you referenced. You can order this product by following the product link that I have provided or by contacting customer service at 1-800-298-8924.
view full answer...

Recommendation for an Aluminum Toolbox for a 16 x 12 x 14 Inch Generator
I have a good option for you. The box will be a little larger than the dimensions you have given but it is the closest match I could find. Take a look at the DeeZee box # DZ61. This is an aluminum box that measures 24 inches long, 18 inches wide, and 18 inches tall.
view full answer...

Is the UWS Aluminum Foot Locker Storage Box # UWS01049 Waterproof
For an item to be classified as waterproof it would have to be able to be submerged under water for a certain period of time and the inside would have to remain dry. Because water could get in if this box were submerged, it can only be classified as weather or water resistant. Under normal rainy conditions, it should keep items inside dry. Under heavy driving rains, items inside could get wet. Anything inside that you do not want ot get wet would need to be placed in plastic.
view full answer...

How Does the UWS Truck Bed Toolbox Install In a Truck Bed
The UWS Truck Bed Tool Box # UWS00434 that you referenced will use the included J-bolts to install onto your truck. I am including a link to a video review of a similar Dewalt toolbox. The video will show the J-bolts and how they attach the toolbox to the truck bed rails.
view full answer...

How Does the Toolbox # UWS04548 Install Into a Truck Bed
The UWS Deep, Angled Truck Bed Toolbox # UWS04548 that you referenced will use the included J-bolts to install onto your truck. I am including a link to a video review of a similar Dewalt toolbox. The video will show the J-bolts and how they attach the toolbox to the truck bed rails.
view full answer...

Fit of DeeZee Wheel Well Toolbox # DZ95D on 2012 Dodge Ram Quad Cab
According to DeeZee, the Wheel Well Toolbox you mentioned, part # DZ95D will fit your 2012 Ram, regardless of cab configuration or bed length. I would suggest you take a look at the photo I edited for you that shows the dimensions of the box. You could then compare the measurements shown to the available space in your bed to confirm fit. Make sure to measure the distance from the rear of the wheel well to the back of the closed tailgate to ensure it is greater than 20-1/2 inches.
view full answer...

Is There a Driver Side DeeZee Specialty Series Wheel Well Toolbox
Yes, we do carry a drivers-side wheel well toolbox like the DeeZee Specialty Series Passenger-side Wheel Well Toolbox, # DZ94B. You will want to look at the DeeZee Specialty Series Driver-Side Wheel Well Toolbox, # DZ95B. I have attached a link to this product for you. The photo on the product page is a generic photo that shows the toolbox on the passenger side, but this is the driver side toolbox to accompany the passenger side toolbox that you referenced.
view full answer...

What are the Measurements for UWS Crossover Toolbox # UWS00331 and Will it Fit a 2006 Toyota Tacoma
The UWS toolbox, # UWS00331, is actually 60 inches long at the top and 52 inches long at the bottom. I have included a picture that shows the measurements of the box. This box is not listed as a fit for the 2006 Toyota Tacoma but you can also go by the measurements to determine fit. I have included a link to all of the toolbox options for a 2006 Toyota Tacoma. When you open the link just select the cab size you have to see the available options.
view full answer...

How Does the UWS A-Frame Trailer Toolbox, # UWS04531 Attach to a Trailer
Bascially, to install the UWS A-Frame Trailer Toolbox, # UWS04531, you will need to drill holes in the bottom or sides of the box, depending on how and where you will be mounting it, and bolt the box to the frame of the trailer. To keep out moisture make sure to seal the holes with silicone # 0160297. You will need to provide your own hardware.
view full answer...

Will the UWS Black Crossover Toolbox # UWS00375 Fit a 2011 Chevy Silverado
The UWS Toolbox, # UWS00375, will fit a 2011 Chevy Silverado with a standard bed, 6-1/2 feet long or 8 feet long. It will not fit step side beds or beds that are 5-1/2 feet long. I have included a link to the toolbox main page for the 2011 Silverado. Select your bed length and type from the list to see the available options. On any of the boxes, always compare the measurements of the box listed on the product page to the available space in the truck.
view full answer...

Dimensions for Installation of the DeeZee Wheel Well Toolbox # DZ956 in a 2003 Dodge Ram Pickup
The DeeZee Wheel Well Toolbox, # DZ956, will fit on either the drivers side or passengers side and is properly sized for truck beds as short as 6 feet long. I provided a drawing that shows the dimensions of this box so you can measure to be sure the box will work in the bed of your 2003 Dodge Ram 1500 Pickup with 6.5 foot bed.
view full answer...

Will the DeWalt Contractor Series Truck Bed Toolbox # DCSD70LPB Fit a 2008 Toyota Tundra Double Cab
According to our friends as DeWalt, the Crossover Toolbox you mentioned, part # DCSD70, will fit your 2008 Toyota Tundra Double Cab short bed. I have provided a diagram showing the dimensions of the toolbox. I would recommend comparing the measurements shown to those of your truck bed to confirm the fit.
view full answer...

How Does the DeWalt Industrial Truck Bed Toolbox Mount on a 2011 Dodge Ram 2500
The DeWalt Industrial Truck Bed ToolBox, # DCS70, will mount to your truck bed using j-hooks. The j-hooks will secure the toolbox to the underside of the truck bed side rails. I have included a video showing how the j-hooks install on the toolbox.
view full answer...

Will the UWS Tool Box # UWS06187 fit in a 2007 Toyota Tundra 4 Door with a Bed Liner
The UWS Truck Bed Toolbox # UWS06187 that you referenced is confirmed to fit your 2007 Toyota Tundra 4 door. The bed liner should not pose a problem for you either. To be sure you could measure the distance between the bed rails of your truck. As long as you have more than 61 inches in width the # UWS06187 should fit fine.
view full answer...

Availability of Replacement Key for UWS Toolbox UWS00388
The face of your lock cylinders should have a key number stamped on them (see photo). To order a replacement key, use the provided link. Once on that product description page, add the key to a shopping cart, and type in the number of your lock in the box that is provided.
view full answer...

Will UWS ProGrade Series Toolbox # UWS07294 Fit a 2007 Nissan Frontier XE King Cab
I spoke with my contact at UWS and they said they list the UWS ProGrade Series Toolbox, part # UWS07294, as fitting 1998 to 2011 Nissan Frontier, excluding the Crew Cab. They did not show anything about not fitting on the King Cab. They said you might want to take some measurements on your truck to see if the measurements will work with the dimensions listed for the # UWS07294 tool box. The overall dimensions on the toolbox is 62 inches long x 19-1/2 inches wide x 13 inches tall. Some of
view full answer...

Is the UWS Black Angled Crossover Toolbox for a 2004 Toyota Tacoma Water Tight
In order for something to be considered water tight or water proof, it would have to be able to be submerged under water for a certain amount of time and not let in any water. This toolbox cannot claim to be water proof as water would eventually get in. However, if going through a car wash or rain storm, the contents should remain dry. We still recommend placing items that cannot get wet inside of a sealed plastic bag or container to be certain.
view full answer...

Will UWS Crossover Low Profile Toolbox # UWS00419 fit 2004 Tacoma Extended Cab with Standard Bed
I have spoken with my contact at UWS, who confirms that the Angled Truck Bed Toolbox you mentioned, part # UWS00419 is indeed a fit for your 2004 Tacoma Xtra Cab with standard (not stepside) bed. The box features the angled sides to clear the wheel wells. I would also recommend taking some measurements of your truck bed and comparing them to the provided diagram to confirm fit.
view full answer...

Will the UWS Truck Bed Toolbox fit on a 2008 Nissan Frontier King Cab With Bed Liner
I spoke with my contact at UWS and the UWS Toolbox, # UWS00404, will fit on your 2008 Nissan Frontier King Cab with the factory bed liner installed. This toolbox uses J-bolts that hook around the lip of the side rails on your truck bed. The J-bolts are included with the toolbox. The only modification that would need to be made would be to the bed liner. The J-bolt will grab on to the lip of the side rail of your truck bed and if the bed liner interferes, then you may need to cut a small slot
view full answer...

Will the UWS Chest Style Toolbox # UWS01026 Fit in a 2007 Nissan Titan Crew Cab
We do have the UWS chest style toolbox, # UWS01026, listed as a fit for the 2007 Nissan Titan Crew Cab. I have also included a link to all of the chest style boxes we list as a fit for your truck. For any box, I do recommend comparing the measurements listed on the product pages to the measurements in the available space in the truck bed to make sure they will fit. I attached drawing of the UWS Toolbox with dimensions for you to see.
view full answer...

Will the UWS Toolbox # UWS00380 Fit a 2001 Toyota Tacoma Short Bed
On the UWS toolbox # UWS00419, the measurement from underneath, where it will sit on the rails, down to the bottom of the box is 11-3/4 inches. I have included a picture that shows all of the box measurements for you.
view full answer...

Dimensions for UWS Truck Bed Tool Box Part # UWS00380
I called our contact at UWS and confirmed that the dimensions we have listed for the UWS00419 are indeed correct. There is not much of a difference between the UWS00350 and UWS00419 boxes. If you look at the diagram I produced, you can see the difference in depth between the two boxes. The differences are highlighted in red.
view full answer...

Crossover Style Toolbox Options for a 2009 Toyota Tacoma Double Cab
The UWS Toolbox, part # UWS04546, will work on your 2009 Toyota Tacoma double cab with factory bed liner. The only interference you may have with the bed liner is installing the j-bolts that hook to the under side of the bed rails. The crossover style tool boxes for your truck all use the j-bolts to secure to your truck. You may need to cut out part of the bed liner if there is not enough room for the j-bolts to secure under the bed rail. I have included a video demonstration of a crossover s
view full answer...

Will the UWS Truck Bed Fender Well Toolbox # UWS01626 fit 2004 Dodge Dakota Quad Cab
I spoke with my contact at UWS, who tells me that the UWS Truck Bed Fender Well Toolbox, part # UWS01626 is not listed as a fit for the Dakota pickup trucks. However, if the listed dimensions of the box conform with your truck bed, the toolbox should work for you. You can measure your truck bed and compare the measurements with the provided diagram that shows the dimensions of the toolbox. The width of the box is not really crucial, but the overall length of 48 inches is important. If you alr
view full answer...

Is the Finish of the DeeZee Truck Bed Toolbox # DZ6160NB Painted or Powder Coat
The DeeZee tool box you referenced, part # DZ6160NB features a powder coat black finish, not paint.
view full answer...

Truck Bed Tool Box Recommendation for a Base Model 2012 Toyota Tacoma Truck
Yes, I checked with DeeZee to be sure and they do recommend the # DZ8160N single lid truck bed toolbox for your 2012 Toyota Tacoma, if it is not a stepside model. If you have a stepside model 2012 Tacoma the only option available is a chest style box, like the DeeZee Utility Chest, # DZ8537.
view full answer...

Weight Capacity of DeeZee Truck Box Part # DZ8160N
I spoke with one of my contacts at DeeZee, who tells me that there really is not a weight capacity on their truck boxes. Stating an actual capacity would be difficult due to the many variables involved. A box installed on a truck driven at 20 mph exclusively on smooth-as-glass paved roads with perfectly poured concrete would have a much higher capacity than a box used in a real world setting that includes pot holes and uneven pavement. Given the real world situation, my contact said he would
view full answer...

Will UWS Truck Bed Toolbox # UWS00405 Fit a 1994 Chevrolet C/K Series Stepside Truck
Yes, the UWS Truck Bed Toolbox, part # UWS00405, will fit your 1994 Chevrolet C/K Series Stepside truck. The Stepside truck will have a step in front of the wheel well and a step behind the wheel well on each side of the truck bed. I would also recommend to use the dimensions listed on the product page of the toolbox and make sure they will match the bed of your Stepside truck. I am including a video link to a UWS toolbox being installed on a truck.
view full answer...

Will DeWalt Truck Bed Toolbox # DCS70 Fit a 2011 Ford F-350 Crew Cab With 8 Foot Bed
Yes, the DeWalt Truck Bed Toolbox, part # DCS70, will fit your 2011 Ford F-350 Crew Cab with 8 foot bed. I am including a link to a video review on this DeWalt toolbox. It is also available in black # DCS70B.
view full answer...

Will the UWS Crossover Toolbox # UWS00366 Fit a 2012 Ford F-150 With a 6-1/2 Foot Bed
I spoke with my contact at UWS and they said the UWS Toolbox, part # UWS00366, will fit a 2012 Ford F-150 Regular Cab, Super Cab, Super Crew Cab with the 6-1/2 foot bed.
view full answer...

Is the Construction of the UWS Toolbox # UWS01022 Waterproof or Weatherproof
The UWS Toolbox, part # UWS01022, is weatherproof construction, which means it will protect the contents from the rain and other bad weather conditions. It has a heavy-duty MicroSeal stripping around the inside of the lid that helps seal out most of the moisture, dust and dirt. It is not waterproof because to be considered as waterproof the toolbox would have to be submerged under water and have no leakage into the inside. This toolbox would not be able to do that. I am including a link to a
view full answer...

Will the UWS Truck Bed Toolbox # UWS06199 fit 2012 Ford F150 Crew Cab 6.5 ft Bed
According to our friends at UWS, the tool box you mentioned, part # UWS06199 is indeed a fit for your 2012 F-150 Crew Cab with 6.5 foot bed. Just to confirm, I would recommend measuring your truck bed and compare the measurements to the diagram I have provided to make sure that the shown dimensions of the box will fit the bed.
view full answer...

Chest and Wheel Well Toolboxes for a 2012 Dodge Ram 1500
The DeeZee tool box, # DZ8560, that you have referenced would be a good choice for a chest style box. This box is 60 inches side to side, 19 inches front to back, and about 16 inches tall. Compare those measurements with the space in your truck to determine if it fits your needs. For matching saddle bag type of tool boxes, you can use # DZ956. These boxes fit under most tonneau covers. But, I always recommend checking the measurements on the product page so you can compare them to your truck.
view full answer...

Recommended Chest and Side Rail Style Toolboxes for a 2012 Ram 1500 Sport With 6.4ft Bed
Does your 2012 Ram 1500 Sport have a Regular Cab, or does it have the Crew Cab? For either cab style, you should be able to use the DeeZee chest style toolbox # DZ8560 that you referenced. This box features a slanted front to eliminate interference with the wheel wells. Side rail tool box # DZ8748 would fit your truck, but unfortunately we do not offer a side rail style toolbox that would sit below the top of the bed rails. The # DZ8748 box will extend 5 inches above the top of your bed ra
view full answer...

Will the UWS Crossover-Style Truck Bed Toolbox Part # UWS00419 fit 2012 Colorado Crew Cab Short Bed
According to our friends at UWS, the Crossover-style truck bed tool box you mention, part # UWS00419 will indeed fit your 2012 Chevy Colorado Crew Cab short bed. The box is not available without the UWS emblem, but the emblem is a thin aluminum plate held in place by double sided adhesive tape, and can be removed if you so desire.
view full answer...

Will DeeZee Chest Style Truck Bed Toolbox-Black # DZ8546B Fit a 2004 Nissan Frontier With 6 Foot Bed
The overall dimensions on the DeeZee Chest Style Truck Bed Toolbox-Black, part # DZ8546B, are 46-1/2 inches long x 19 inches wide x 15-9/10 inches tall. It shows as fitting two different bed sizes, the 4 foot 8 inch bed and the 6 foot 3 inch bed, on the 2004 Nissan Frontier. I would recommend to measure the width of your truck bed where you will want it to sit up against the cab and determine if there is enough room for the dimensions of the toolbox listed above. This toolbox is a utility
view full answer...

Will DeeZee Narrow Crossover Tool Box Part # DZ6160N Fit a 1992 Toyota Pick Up
According to our friends at DeeZee, the Crossover Tool Box you mentioned, part # DZ6160N will fit your boyfriends 1992 Toyota Pickup. The same box is also available in a black finish as part # DZ6160NB.
view full answer...

Order Tracking
Shipping Information
Contact Us
About Us

Help Videos and Articles
Search
Privacy Policy
Your Account Login