Expert Answers about Enclosed Trailer Parts

Enclosed Trailer Parts

Replacement Ventline Cover for a V2094 Vent on a 2009 Dutchman
As long as your Ventline V2094 vent was made after 2008, which it sounds like it was, the Replacement Dome Assembly # BVD0449-A01 that you referenced would be the correct replacement lid cover for your 2009 Dutchman. The only other color option we carry would be the smoke version part # BVD0449-A03.
view full answer...

Availability of Replacement Parts for Ventline Rounded Dome Trailer Roof Vent
The Ventline product you reviewed, part # V2092SP-28, is a complete vent assembly intended for a rough roof opening of 14-1/4 x 14-1/4 inches. It consists of a wedge-shaped white plastic dome attached to a galvanized steel frame with hand-crank assembly, a removable screen, and a white plastic 2-1/8-inch-deep garnish (interior trim ring). Please note that this part requires an installation kit, part # RVIKIT100, which consists of mounting hardware and a urethane caulk sealer. If your traile
view full answer...

Can the Ventline Ventadome Trailer Roof Vent be Installed in a 1 Inch Thick Roof
After inspecting roof vent # V2094SP-30 and the included bezel, I have come to the conclusion that you would just need to trim 13/16 of an inch off the bezel on the end that sticks into the vent. This should allow you to flush mount the vent and bezel in your 1 inch thick roof. I also recommend installation kit # RVIKIT100 which comes with the hardware and silicone needed for installation.
view full answer...

Will the Rumber Saddle Rack fit a Saddle Rack from a 4 Horse Platinum Trailer
Yes, I spoke to my contact at Rumber and found that the Rumber Saddle Rack, part # 9901-0, is hollow underneath and was left that way so that it can be modified to fit any application the customer wants to mount it to. Mounting can be accomplished by drilling holes and bolting the saddle rack to any sturdy mount including a pedestal.
view full answer...

Overall Dimensions of Stromberg-Carlson Manual RV Step Part # SM-24-40
The Stromberg Carlson Manual Pull-Out Step for RVs, part # SM-24-40, is illustrated in the attached photo. I pulled a sample from our warehouse and took key measurements for you; these are shown on the image. Overall outside width is exactly 27.5 inches; depth is 9.5 inches. There are 4 mounting holes; center-to-center hole spacing left-to-right is 26.5 inches and front-to-back is 7 inches.
view full answer...

Replacement Roof Vent Lid for 2007 Haulmark Trailer
I do not have any information about which particular vent Haulmark used on their trailers, but you can easily determine which replacement lid you need. The easiest way to do this would be to provide me with any manufacturer and model number information you might be able to find. With this information, I can check with the various manufacturers for a replacement lid. If you cannot find any info on the remaining vent, you will need to measure the existing vent. When measuring for a replacement ve
view full answer...

How To Replace Damaged Roof Vent Cover Using Replacement Dome Assembly # BVD0449-A03
To remove the damaged vent cover, remove the connection to the actuating strut, so the cover can tilt all the way upwards. To do this, you will need to remove the interior screen, the knob and the interior trim piece. Then, remove the two screws that hold the actuating arm in place, which will allow the actuating arm to be slid out of its track on the cover. Tilt the cover (or what is left of the cover) straight up so that it is at a 90 degree angle to the roof of the trailer. Then, push the lid
view full answer...

Mounting The Redline Enclosed Trailer Ramp Spring # ERS80S6 On a Finished Enclosed Trailer
The diameter of the cable reels on Redline Enclosed Trailer Ramp Spring part # ERS80S66 is 5 inches. To install this spring, I recommend attaching it to your header as close to the top of the door as possible. Since you only have 2-1/2 inches of clearance to your ceiling, you will need to modify your ceiling to accommodate the additional height of the cable reels. You also want to make sure that the cables do not rub against any part of the door frame. If you have not worked with a torsion s
view full answer...

Dimensions of TrailerWare Wheel Well Liner Kit # TW8010050
After speaking with my contact at TrailerWare, I can confirm that the TrailerWare Wheel Well Liner Kit # TW8010050 comes in one 10-foot long by 4-foot wide roll that will need to be cut to fit your specific set of wheel wells. The number of wheel wells you can cover with this kit will depend on the size of the wheel wells themselves. I recommend measuring them to ensure the 40 square feet you will receive will be enough. The adhesive spray that is needed to apply the liner to your wheel w
view full answer...

Installing Trailer Door Hook and Keeper # 383400
You will usually see the hook portion mounted on the trailer door, with the keeper connected to the side of the trailer, but there is no reason why you could not install it the other way, if you wish. Just to be certain, I checked with the manufacturer who told me the same thing.
view full answer...

Replacement Vent Cover for 2010 Elkridge 5th Wheel Camper
I contacted the parts folks at Heartland, and was told that your 5th wheel was originally equipped with an Elixir roof vent. We do offer replacement lids, in smoke as part # BV0554-03 or white as part # BV0554-01.
view full answer...

Can Stromberg-Carlson Manual Pull-Out RV Steps, Part # SM-24-20, Fit on 2000 Ford F-350 PickupTruck
My contact at Stromberg-Carlson is unable to advise of the fit of their Manual RV Steps, part # SM-24-20, in any installation other than that for which their product is intended. Certainly there will be cases where this product might be successfully re-purposed for a non-standard application, such as their installation on a Ford pickup. What I have done to assist you in evaluating this potential project is include the installation instructions for the steps along with a photo that shows the
view full answer...

Replacement Non-Powered Roof Vent Cover Options for an Itasca Sundancer Travel Trailer
I have located three possible solutions, including the option you originally requested for your Itasca Sundancer. We have three non-powered roof vent covers that may work for you. I attached a photo showing covers and dimensions for you to make the correct selection. For the Ventmate, # 69284, that you originally asked about, I have given you the hinge dimensions as well as the center dimensions. For this part the hinges are molded plastic. Another option we offer is the Ventline, # BV0554
view full answer...

How Many Screws Should be Used to Install the Horse Trailer Side Pads part # HTP60BK
It really is up to you to decide how many pad screws to use to install the Horse Trailer Side Pad # HTP60BK that you referenced, but typically customers use between 12 and 16 screws. The part number for the screws is PS-8.
view full answer...

Will the Redline Vent # M1659VEN Replace an Older Trailer Vent with a 14 by 14 inch Hole
The Redline Vent # M1659VEN that you referenced is a 14 inch by 14 inch square vent that is recommended for square cut holes that are 14-1/4 inch by 14-1/4 inch holes. Since the hole in your roof is 14 inch by 14 inch it should work just fine for you. The extra 1/4 of an inch should not make a difference.
view full answer...

What are the Measurements of the RV Manual Pull-Out Step # SM-2410-39
When extended out, from the mounting surface down to the surface of the bottom step is 21-1/2 inches. From the mounting surface to the top of the first step it is 4-1/2 inches, from there to the next step down is 8-1/4 inches, and from the second step to the last step it is 8-3/4 inches. I have linked the instructions that included a diagram with measurements and video links on installation and measurements for the RV Manual Pull-Out Step, # SM-2410-39.
view full answer...

Can Rain Get Into the Ultra-Fab Solar-Powered Plumbing Vent
The opening on the solar-powered vent # UF53-945001 is up underneath the top portion so it is very unlikely that rain could get in. But it is not outside the realm of possibility if the rain was hard enough (sideways rain in high winds). I have included a link to a video review of this vent for you. As far as keeping rain out, the Ultra-Fab solar-powered vent would be my top choice over Ventline vent # VP-543SP. The Ventline vent is also hardwire only so it will need to connect to 12 volt pow
view full answer...

Is there a Trailer Roof Vent that Will Fit a Roof that is 1 Inch Thick
You can use the Ventline Ventadome Trailer Roof Vent, # V2110SP-24, and then just trim down the garnish to the size you need. The garnish that comes with the vent is actually 2-1/8 inches deep to start with. I have included a link to a video review of this vent for you. We also recommend using the installation kit # RVIKIT100 when installing a vent.
view full answer...

Replacement Trailer Ramp Springs
We have several hinge pins like # HP412G that I have linked for you, but it sounds like you need actual springs. We have some heavy duty ramp springs like # RS16933RH and # RS16933LH if you happen to have a heavy duty equipment trailer like what they haul tractors and other large equipment on. For an open utility trailer you may be able to use a tailgate assist like # GL1 or # RA-27C. Or for an enclosed trailer we have springs that are similar to garage door systems. I have linked those as w
view full answer...

Will the RV Electric Sliding Step # SP-24-200 fit a 38 ft Montana 5th Wheel
The overall dimensions of the RV Electric Sliding Step # SP-24-200 that you referenced are 25-3/4 inches wide x 30-1/2 inches deep. You will need to check the area where you want to install the steps to see if you have enough clearance for them. If you do have the clearance these steps are a universal style installation that will bolt to the frame of your Montana 5th wheel with (4) 3/8 inch diameter bolts and flange nuts that you will need to provide.
view full answer...

How Wide is the RV Manual Pull-Out Step # SM-24-30 and what is the Diagonal Measurement
The width of the step is 24 inches. The only time the number 30 is mentioned is in the part number and it does not reflect any of the dimensions of the steps. The # SM-24-30 has a diagonal measurement of 41 inches from the top corner to the bottom of the bottom step surface. Check out the picture I attached to see the dimension I am referencing.
view full answer...

Is the Frame of Trailer an Adequate Place for the RV Electric Sliding Step # SP-24-300 to Attach to
The frame of your trailer should be the strongest component of your trailers constructions and should be more than adequate to use for installing a RV Electric Sliding Step # SP-24-300. Even if you used a mounting plate to install the steps it would still have to be attached to the frame, so either way the frame will see the same load. Yes, the # SP-24-300 comes with a door activated switch and a manual lockout to allow you to keep the stairs extended when parked. To install this you will
view full answer...

How to Choose the Correct Replacement Vent Cover For 2011 Heartland North Trail BRS
There are a few different ways to determine the replacement vent cover you will need on your 2011 Heartland Northtrail BRS. Measuring the vent is the first place to start. Most standard vents are 14-1/4 by 14-1/4 inches wide, 14 x 14 inches wide or 13 x 14 inches wide. Next, if the manufacturer name is on the vent that will help. Finally, you will need to look closely at the hinged portion of the the vent. If there is a rolled, continuous metal hinge attached to the vent cover like on the Ven
view full answer...

Will Stromberg-Carlson RV Pull-Out Step, Part # SM-2410-39, Fit 2010 Jayco Eagle RLTS 5th Wheel
The Stromberg-Carlson RV Pull-Out Step, Part # SM-2410-39, measures 27-1/2 inches wide and attaches to the RV with 4 carriage bolts. You might want to review the two videos linked to this email; one shows how to measure your existing RV steps and the other covers the installation process for this product. It may be necessary to remove some fascia components on your RV in order to access the step mounting hardware. I reviewed various 5th wheels on the Jayco website but no specifics are provide
view full answer...

How Does a Lend-a-Hand Folding Grab Handle Install
The Lend-a-Hand Folding Grab Handle # AM-300 that you referenced installs with 2 screws on each mounting bracket. If you look at the brackets you should see 2 holes that screws will go through and then screw into your trailer. To remove or tighten these screws you will just need to get a Philips head screw driver and tighten/loosen the screws.
view full answer...

What Size Hole Should be Drilled to Install a 2-Piece Polypropylene Trailer Vent
To install the 2-Piece Polypropylene Trailer Vent # HMAV2-AVT2 and have it functional you will need to drill a 3 inch hole with a hole saw like you suggested.
view full answer...

Availability of RV Slide-Out Steps with Rise Shorter than 8 Inches
We do have a manually operated pull-out step, part # SM-24-20, a 2-step unit that features a 7-inch rise between steps. This might be a better choice and hopefully the 1 inch difference will make a difference for your wife. There is also a 3-step unit, part # SM-24-30 that also has a 7-inch rise between steps. To determine which unit you need, measure from the mounting surface where the steps would attach down to the ground, and compare that distance with the total height of each unit sho
view full answer...

Availability of Replacement Rubber Socket for Redline Door Holder, Part # DH100
We do offer a replacement rubber socket for the Redline Door Holder, part # DH100. The replacement rubber socket is part # DH100S. We also offer 2-1/4 inch replacement plungers, part # DH100P.
view full answer...

Looking for Replacement Roof Vent Cover Model # CS 610SA For 2002 PACE American Sport Trailer
I could not find a reference to the # CS610SA vent you mentioned. The best strategy for finding a replacement is to measure the outside dimensions of the roof vent and take note of the hinge configuration. Then, look for a replacement that uses the same hinge configuration and is the same size. Unfortunately, I do not have any reference information showing which model years of trailer or camper used what model number vent cover. If you would care to get an outside dimension of the roof
view full answer...

Choosing/Sizing the Correct Trailer Ramp Spring for a Ramp Door
When selecting ramp springs for a trailer ramp, you will want to know the diameter of your hinge pin and how much space you have available in the hinge. A typical horse trailer or utility trailer ramp uses 3/4 inch hinge pins and would require two ramp springs with a 3/4 inch inner diameter. The ramp springs that we carry fit 1-1/2 inch diameter hinge pins and are designed for use with heavy-duty steel ramps like those on equipment trailers or car haulers. The spring slips over the hinge pin
view full answer...

Can the Polypropylene Trailer Vent Be Trimmed to Fit Thin Trailer Walls
If you find that the wall of your trailer is too thin then you would have to trim at least one of the pieces to allow for a secure fit but make sure it is a straight cut and not an angle cut. Otherwise it may not fit properly together.. ideally you would want a little wiggle room to adjust it as needed without leaving too much of a gap. As for the positioning I would have blades facing down so it is harder for moisture to get in.
view full answer...

Can the 66 Inch Enclosed Trailer Ramp Spring be Cut Down to Fit a 48 Inch Opening
I spoke with the manufacturer of the enclosed trailer ramp spring # ERS80S66. They informed me that the minimum length you can cut it down to is 45 inches. This will leave enough room for it to wind. So the 48 inch opening you have will be large enough and everything should be able to move freely. Please note that installation of a spring like this one is best handled by a professional or someone with a lot of experience with torsion springs. A local overhead door company could perform the in
view full answer...

Will Stromberg Carlson Pull Out Step # SM-24-10 Fit on 2011 Diamond Cargo Trailer Side Door
The Stromberg Carlson Pull Out Step # SM-24-10 mounting is 4 inches wide by approximately 24-3/8 inches long. As long as the side door opening on your trailer fits these measurements, I see no reason why this step would not work for your needs. Just know the drop of this step when activated is 7 inches. Many cargo trailers ten to be low to the ground and this step could cause interference. I do recommend that you mount this step on metal rather than wood or flooring material. I have provid
view full answer...

Recommendation For Attaching Horse Trailer Side Pads
For the installation of your 60-inch horse trailer side pads, I recommend using the Trailer Horse Pad Screw # PS-8. The pads are installed in the trailer directly via the screws and can be mounted wherever is convenient. I have included a photo from our page for the 60-inch Horse Trailer Side Pads # HTP60BK showing how these screws are utilized.
view full answer...

What Are Dimension of the 7/16-Inch Pin Used in Part # SL716SS?
The Redline Spring Latch, part # SL716SS, uses a 7/16-inch sliding pin that is 6-3/4 inches long, with a handle end that measures 1-7/8 inches. The attached photo provides these and other measurements. The pin and spring are stainless steel; the base is aluminum. Please note that mounting hardware is not included with this part.
view full answer...

What Vents will the Ventline Vent Cover # BV0554-03 fit On
The Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents # BV0554-03 that you referenced is designed to work on 14-1/4 inch by 14-1/4. This cover will fit standard Ventadomes and Post-1995 Elixir trailer roof vents. The other option you have would be a Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent # BVD0449-A03. The big difference is that this lid uses three individual hinge clips, whereas the # BV0554-03 uses one continuous hinge. Check out the picture I
view full answer...

What Size Hole Should Be Cut to Install a Redline Roof Vent # M1659VEN
The recommended opening size that needs to be cut to install the Redline Vent # M1659VEN is 14-1/4 inches by 14-1/4 inches. I attached a review video for this product for you to check out also.
view full answer...

Quantity and Pin Diameter of Bolt-On Stainless Steel Spring Latch, # SL716SS
The Bolt-On Stainless Steel Spring Latch, # SL716SS, is sold in quantities of 1. The pin diameter is actually 7/16 inches. I have linked a video review for you. We have another latch option. Weld-on latch # SL58W has a 5/8 inch diameter pin. I have linked a video review for it as well.
view full answer...

Installation of Redline Butterfly Vent # 371800
On the Redline Butterfly Vent, part # 371800, the location of the nob does not really matter, usually on either side. We recommend to install the butterfly vent on the trailer so that the triangular openings of the vent are parallel to the ground, with one triangular opening to the front of the trailer and the other triangular opening to the rear of the trailer. I am including a link to a video review of the vent and in the video he will be holding the vent the way we recommend to install it
view full answer...

Trailer Side Door Lock for a Trailer with a Side Door that Sticks Out Up to 2 Inches
What you could do is use the universal cam-door lock # 383200. You can then get a bar with the proper offset needed to work with your trailer door. I have included a link to a video review of this product for you to view.
view full answer...

Does the Econo Porch Trailer Step # EHS-102-R Fold for Storage
The Econo Port Trailer Step, # EHS-102-R, does fold to make it easier to store when on a trip or at home. The dimensions of the steps when folded is approximately 47 inches by 35 inches and the thickness is approximately 1-1/2 inch. There is some assembly required to fold and unfold the step, but it only involves attaching the braces using the included screws and nuts. The handrail will also attach using provided screws and nuts.
view full answer...

Measurements and Installation of Manual RV Pull-Out Steps
I have included a picture that shows the measurements of the manual folding step, # SM-24-30. Because of the way the steps are designed, you would not be able to pull out just 2 steps. You would have to pull out all 3. I have also included some video links that will help explain installation and measurements. On the top the center to center distance between the mounting holes is 26 inches. For a 2-step version use # SM-24-20.
view full answer...

Can Redline Aluminum Gravel Guard, Part # GG18, Repair 2006 Continental V-Nose Cargo Trailer
The Redline Aluminum Gravel Guard, part # GG18, is 18 inches wide and sold by the linear foot. The thickness of the material is 0.025 inches (0.6 millimeters) and it is fairly flexible. I expect you would easily be able to bend and mold it to fit the curvature of your cargo trailer. However, because of the relative softness of this material I do not expect that it would tolerate impact from rocks and other road debris without itself becoming dented or dimpled. I have included a video showing
view full answer...

Does Ventline Powered Roof Vent V2128-611-00 Run Off of Household AC Power
Because the Ventline fan # V2128-611-00 is 115 volt, it would have to run off of AC power (110 volt shore power). This item is normally found on larger motor homes and will run when connected to shore power or when using a generator. Because the motor is an AC motor, you cannot reverse the polarity and run the motor the other direction. It only runs one way.
view full answer...

Distance Between the Mounting Brackets on the Lend-a Hand Folding Grab Handle
I went out into our warehouse and measured the distance between the mounting brackets and found the distance to be 19-1/4 inches. Check out the video and picture I attached to see this measurement. The mounting brackets themselves measure 3-7/8 inches tall. Using nuts, bolts and washers to install the # AM-200 would work very well as an installation procedure.
view full answer...

How to Determine the Correct Roof Vent Cover for a 1993 Car-Mate Enclosed Trailer
There are a few things to look at when looking for the correct replacement vent cover for your 1993 Car-Mate trailer. The first item that will help is knowing the manufacturer of the vent on the trailer, such as Elixir, Jensen, etc. The next thing that you will want to consider is the size of the vent itself. The Ventmate Vent Cover, # 61634, that you referenced is designed to fit plastic vent frames that are 14 inches by 14 inches. The actual outside to outside dimensions of this vent cover
view full answer...

Can the T-Handle Door Latch Assemblies # L4080 Be Ordered Keyed-Alike?
According to my Redline representative, all of the # L4080 T-Handle locks are keyed alike. I have confirmed this myself by pulling a few of them off the shelf in the warehouse. They all use the same key number, so if you order four of them, they will all be keyed alike.
view full answer...

Availability of a 3-Step Electric Step for Travel Trailers
You have a valid concern about operation of this product with a partially depleted trailer battery. I researched similar products and I did not find any specifically intended for travel trailer use. One solution is to procure a separate 12V automotive battery for operating the steps, provided that your trailer has a suitable place to locate one without requiring excessively long wire runs or the risk of causing pinched or shorted wiring. In this scenario a battery charger might also be a good
view full answer...

Can a Metal Replacement Vent Cover be Used to Replace a Plastic Vent Cover
Replacement vent covers are very specific in terms of what vents they will fit. Metal cover # BV0534-00 is designed to fit Ventline Ventadome roof vent model V2110. If your vent originally had a plastic cover chances are this metal one will not fit. I have included a link to the vent covers we carry. If you are not sure of the model number you will need to look at the hinge style on the existing cover and compare it to the hinges pictured on the product pages of the covers.
view full answer...

Universal Cam-Door Lock Recommendation for Toy Hauler that the Door Does not Close all the Way
I believe I know what is happening. It sounds like your door latches are at the middle of your door which leaves the top of the door slightly open. You could use a Universal Cam-Door Lock for Enclosed Trailers # like what you referenced. I would run it across the top lip of your trailer ramp so that it will secure the top of the door as well. Depending on the setup you might consider leaving your current latches and then install a # 383200 as well. Or, you could move your current latches h
view full answer...

Enclosed Trailer Ramp Spring Recommendation for Raising a Shed Door
I believe your best option would be the Enclosed Trailer Ramp Spring # ERS120D81. This spring is 81 inches in length and has a capacity of 120 lbs so I believe it would be better suited for the job than the longer spring with a lower capacity # ERS80S96 that you referenced. I also spoke to my contact at M-3 and he informed me that the # ERS120D81 has plenty of capacity to lift the one side of the 125 lb door. This product should help your customer raise and lower the heavy door, if you hav
view full answer...

Dimensions of Stromberg Carlson RV Steps # SM-24-30
The Stromberg Carlson RV steps really are not designed for the purpose you describe. This does not mean that they will not work, but there might be some fabrication work involved in attaching them to the bottom of your van. As you can see in the diagram in the instructions I have linked to, the # SM-34-30 step unit is about 13-1/2 inches tall when closed. When fully folded out, the steps will be about 16-1/2 inches tall, measured from the top of the assembly to the top of the bottom step, whi
view full answer...

Is the Width of the Redline 2 inch Steel Hinge Measured Folded or Unfolded
I spoke to my contact at Redline and he informed me that the 2 inch width is measured when the Redline 2 inch Wide Continuous Steel Hinge # H200 is unfolded.
view full answer...

Can a Universal Cam-Door Lock for Enclosed Trailers be Used in the Horizontal Position
It is possible to use the cam-door lock, # 383200, horizontally but it would need to be placed up higher than the midway point to reduce the amount of stress on it when the door is closed. Take a look at the picture I have included that shows this type of set up. For a lock you could use # BLDL-80.
view full answer...

Replacement Roof Vent Lid for Enclosed Cargo Trailer
To determine which cover you need, examine the existing vent cover (or what is left of it) for a manufacturer name or model number. Take a look at the replacement covers we offer (see provided link) paying close attention to the thumbnail photos showing the hinge configuration. You will need to choose the cover whose size and hinge configuration matches your existing vent. If you are unsure, please email me a photo of your existing vent, making sure to get the hinge in the photo. Having a tap
view full answer...

What Color is TrailerWare Standard Wall Liner Kit # TW8010321
After consulting my contact at TrailerWare, I have found the color of the cushioned, carpet-like material covering the bottom 4 feet of the trailer walls you would cover with the TrailerWare Standard Wall Liner Kit # TW8010321 is a dark gray. I have provided a photo showing a close up of the material.
view full answer...

Determining the Correct Replacement Pull-Out Step for a 2005 Keystone Cougar 5th Wheel Trailer
All of the RV pull-out steps that we carry are 24 inches wide by 8 inches deep. The overall dimensions of the RV Pull-Out Step, # SM-24-30, are 27-1/2 inches by 13-1/2 inches tall by 12 inches deep. I have attached a photo showing these measurements for you. When extended, this step measures 35 inches deep and the step height is 7 inches. This is the closest step that we carry to the dimensions you have provided. I have attached links to two videos for you to check out. One video details how
view full answer...

Installing Manual Pull-Out Steps on 2007 Toyota Tundra
I cannot say that using some sort of RV pull-out step would not work, but I would hesitate to recommend it for a couple of reasons. Since RV steps are not designed for use on a passenger vehicle, there would likely be fit issues and fabrication involved that would make the installation pretty difficult. Your existing step bars would almost certainly need to be removed, as they would most likely interfere with an installation of that sort. The steps would need to be pulled out in order to use the
view full answer...

Can Redline 2-Way Pop-Up Vent # 9106-2756 Be Installed on Trailer Wall Instead of Roof
There is no reason why you could not install the # 9106-2756 on the side of the trailer. Screws needed to install the vent are not included. We have the appropriate wood (# 30587) or sheet metal (# 31071) screws available. Using a silicone sealant like part # 0160297 is recommended to prevent water intrusion.
view full answer...

What is the Maximum Wall Thickness for the Junior Steel Flush Door Latch to Install Onto
I spoke to my contact at Redline and he informed me that the maximum thickness for the panel that you could install this Junior Door Latch # N1980 on would be 3/4 of an inch. Basically, this and the Full Size Door Latch # N3980 that you referenced have the same maximum thickness because they are similarly designed.
view full answer...

Installation Instructions for Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents
Installation instructions are included on the packaging for the replacement vent # BV0554-01. I have included a picture for you of the instructions that should help with the installation.
view full answer...

Can the 96 Inch Wide Enclosed Trailer Ramp Spring be Trimmed to Fit a 92 Inch Wide Trailer
Yes you can cut the shaft on the 96 inch wide ramp spring, # ERS160D96, to fit your 92 inch wide trailer. The shaft is made of steel tubing so the proper saw or power saw blade would cut through it. Be sure to get a straight cut and file down the rough spots. Regarding installation, a professional with experience should install this in your trailer. Torsion springs are under a lot of tension and can be dangerous if you do not have experience with them. A garage door installer would be a good
view full answer...

How to Determine the Correct Replacement Vent Lid for a 1987 Terry Fleetwood Travel Trailer
If the vent on your 1987 Fleetwood is an Elixir brand made before 1995 then vent cover # 61634 will fit. The manufacturer of the vent might be on the vent body somewhere. We have several other replacement lips, see link. If you cannot find the manufacturer of the vent you will have to go by the hinge style. Pictures and/or videos of the lids and hinges are on the product pages for the lids. Trailer manufacturers can use any make of vent and they rarely have record of what was used on any giv
view full answer...

Can the Redline Enclosed Trailer Ramp Spring # ERS80S66 Be Cut Down to 57 Inches
Yes, the Enclosed Trailer Ramp Spring, # ERS80S66, can be cut down to fit the 57 inch space available in your trailer. Redline came out with three general length bars for the ramp springs so they can be cut down to fit specific trailer sizes. One thing to note with this ramp spring is that Redline recommends the installation be performed by someone who has experience winding torsion springs. If you have not performed this type of installation or are unfamiliar with the process, then it is re
view full answer...

Powered Roof Vent for a 2013 Jayco Flight Bungalow Park Model Trailer
If your current vent has a rough opening size of 14-1/4 square inches then the Ventline vent, # V2119-601-00, is the best option for you. The fan and opening mechanism are powered and can be activated with a wall switch, # VC0533-03-A. To install the vent I also recommend the installation kit # RVIKIT100. Another option is MaxxAir vent # MA05100K. It fits the same opening. Its design will negate the need for a manual or automatic opening system. The fan has a thermostat so it can be set to au
view full answer...

How Much Does the T-Handle Locking Stainless Steel Flush Door Latch # L4080 Weigh
No question is too crazy for us! I went out to the warehouse and pulled the T-Handle Locking Stainless Steel Flush Door Latch, # L4080, and placed it on a digital scale. It weighs 1.15 pounds (probably a little less if removed from the plastic bag it was in). I have included a link to a video review for you.
view full answer...

Is Caulk Required when Installing MaxxAir White Trailer Roof Vent Cover # 64643
The MaxxAir vent cover # 64643 uses and exclusive Zero-Leak mounting system to provide a watertight installation. But you will need to drill into the vent frame to mount this vent cover. You would want to use a sealant, like # L0150811.
view full answer...

Can Rain Get Into the Ventline Powered Vanair Trailer Roof Vent # VP-543SP
It is not likely but possible for rain to get into the vent when it is open. The outer lid overlaps the lower housing so water would have to come in sideways (if parked level) for it to get in. Also if the trailer is parked on an incline, the angle required to enter in the vent would not be as severe so you just have to plan accordingly. For installation we recommend using install kit # RVIKIT100.
view full answer...

Choosing the Correct Ramp Springs for Enclosed Cargo Trailer
The springs you mentioned are designed for use on an existing door hinge that uses a 1-1/2 diameter rod or pipe as a hinge pin. The spring would be slipped over the pipe and there would need to be gaps of at least 2-1/2 inches in the hinge barrel on the door and on the trailer to allow room for the width of the spring. The ramp springs are not designed for lightweight doors that have an aluminum skin and a wood core. The correct springs for your application will depend on what you are usin
view full answer...

Replacement Roof Vent Cover for 2008 Dutchman Aerolyte Travel Trailer
After speaking with my contact at Ventline, I believe that the Vent Cover for Jensen Trailer Vents, part # 62008 for Smoke color or # 69284 for White would be your best bet for matching your existing hinges. If you measure the outside dimension of your existing opening, and it is 12-3/4 inches square or less, this is most likely the correct replacement. I have edited a photo showing the hinge detail for you to take a look at.
view full answer...

How Far Down Does RV Electric Sliding Step # SP-24-100 Hang Down from the Trailer Frame
Actually, when mounted flush to the bottom of the trailer frame, when step # SP-24-100 is retracted, it will hang down 6.1070 inches. The 4-1/2 inch drop is how far the step comes down from the retracted position to the extended position.
view full answer...

Can the Universal Cam-Door Lock Be Used on 42 Inch Doors
The Universal Cam-Door Lock for Enclosed Trailers # 383200 that you referenced are the same kind of door latches that are used semi-truck trailers. As long as they are installed properly you should have no problem with them on your grain truck.
view full answer...

What is the Height of the Bolt-On Stainless Steel Spring Latch
I went and measured a Bolt-On Stainless Steel Spring Latch # SL716SS and found that the height of it would be 15/16 of an inch. Check out the picture I attached that shows this measurement.
view full answer...

Is the Fan in the Ventline Ventadome Trailer Roof Vent Reversible
The fan itself only fits onto the motor one way. If you wanted to reverse the rotation of the fan you would need to switch the positive and negative leads on the back of the motor. I tried this with just the motor and it will reverse the rotation. However, since the fan can only be put on one way and the blades are at a fixed angle, reverse the motor direction will also reverse the air flow direction.
view full answer...

Replacement Vent Lid for a Jensen 7000 Series Vent on a 2001 Winnebago Leisure Seeker
We have several vents that can be used as a replacement for Jensen vents. However, you will need to look at the images on the product pages, linked for you, and the dimensions of the opening the entire vent assembly fits in, not just the opening that the lid covers. The part numbers are: # 61628 # 62008 # 69284 # 63112
view full answer...

Does the Enclosed Trailer Aluminum Roof Vent, # RV-626-062, Come with a Garnish
The Aluminum vent, # RV-626-062, comes with the vent itself, built-in screen, and a gasket, but not the garnish. The enclosed trailer vent, # 9106-2756, comes with the vent assembly itself, the black garnish that can be trimmed if you have a thin roof, a built-in screen, and a gasket. If you like the look of the first one, you could always paint this black vent to the color you wanted.
view full answer...

Replacement Vent Lid for a 2009 United ATV/Snowmobile Trailer
You will need to take a look at the hinge on vent cover # BVD0449-A01 to determine if it matches what you have on your trailer. I have included a picture that shows the hinge up close. This cover is designed to fit Ventline Ventadome roof vent model V2110 like # V2110SP-24. It measures 14-1/4 inches square.
view full answer...

Dimensions of the Parts that Make Up the Aluminum Hand Rail for 3 Step Scissor Stair # AHR3
I went out to the warehouse and pulled an Aluminum Hand Rail for 3 Step Scissor Stair, # AHR3, to take some measurements. The longer piece is 43-1/4 inches long. The shorter piece is 39-1/8 inches long. Both pieces are constructed of 1-1/2 inch square tubing. The brackets is 12 inches long and 2 inches wide. The bolt holes are 2 inches apart, but the 2 center most holes are 6 inches apart. I have included some pictures showing these measurements for you.
view full answer...

Is Caulking Necessary When Installing MaxxAir Trailer Roof Vent Cover # 64643
Since the MaxxAir Vent Cover attaches to the existing vent, you will not have any fasteners piercing your roof. Caulking would not hurt anything, but according to MaxxAir, it is not necessary.
view full answer...

Availability of Replacement Roof Vent Lid for 2007 27 Foot Arctic Fox Travel Trailer
My contact at Ventline tells me that part # BV0554-01 in white or # BV0554-03 in smoke would be the correct replacement lids for your travel trailer. These are the only two replacements available, nothing that would be constructed of material that is any thicker than what you currently have.
view full answer...

What are the Dimensions of the Stromberg Carlson Platform Step in the 3 inch Height
I pulled a Adjustable-Height Platform Step # PA-100 from our warehouse to measure the outside dimensions of the legs when it is in the 3 in height and found the dimensions to be 19-1/8 inches by 15-1/4 inches. Check out the video I put together for you so you can see the measurements.
view full answer...

Replacement Vent Cover or Complete Vent Assembly for a Pace Trailer
You may be able to just replace the vent cover. You would need to know the vent manufacturer and its approximate age. This information may be on the vent somewhere. If you cannot find this information, you will need to look at the type of hinge you have and then compare that to the pictures of the hinges for the covers we carry on the product pages. The cover you have referenced, # BV0554-03, is designed for Standard Ventadomes and Post-1995 Elixir Trailer Roof Vents. Replacing the entire
view full answer...

Hole Dimension of Stromberg Carlson Outriggers for RV Manual Pull-Out Steps # SM-01
If you refer to the photo I have edited for you, you can see the complete dimensions of the Stromberg Carlson Outriggers for RV Manual Pull-Out Steps, including the distances between the holes.
view full answer...

Should a Sealant Be Used When Installing Alliance 2-Piece Enclosed Trailer Vent # HMAV2-AVT2
When installing a vent like the Alliance 2-Piece Enclosed Trailer Vent, part # HMAV2-AVT2, to a trailer we do recommend to use a sealant like the Loctite Urethane Sealant, part # L0150811, to help seal the trailer from the elements. The Loctite urethane sealant is applied as a thick liquid to parts before assembly or in seams after assembly to create a waterproof bond in a variety of applications. It can seal doors, windows, vents and other areas in enclosed trailers where water could enter.
view full answer...

Can the Ventline Vanair Trailer Roof Vent with Fan be Left Open When Traveling
I would not recommend leaving Ventline Vanair Roof Vent with Fan, # VP-543SP, open when traveling down the highway because the fan and electric motor would be exposed to the elements. You would not want any dirt, rain or any other type of debris to get inside of the vent and ruin the fan. I spoke with my contact at Ventline and he said structurally the vent can be left open when traveling, but the fan and electric motor would be at risk. It is much easier for rain and dirt to enter the vent
view full answer...

Will Ventline Replacement Dome Assembly # BVD0449-A01 Fit On Phillips Roof Vent V2094
The Phillips model V2094 roof vent is the same as the Ventline Ventadome V2094. Ventline is a division of Phillips products. The Ventline Replacement Dome Assembly, part # BVD0449-A01, you have referenced, will fit your motorized V2094 roof vent. It does not include the spring clip that is used to attach the dome to the base at the hinge. If you need the spring clip you will use the Ventline Replacement Spring Clip, part # VD0453-00. I also carry other replacement parts for the Ventlin
view full answer...

Finding Correct Replacement Vent Lid for Enclosed Trailer
When measuring for a replacement vent lid, you will want the outside dimension of the housing that extends through the trailer roof. This dimension is typically 14 by 14 inches. Closely examine the remaining portion of the vent, looking for a manufacturer name or model number. If you cannot find that information, you can examine the replacement lids we offer (see link) and match them up by the dimension of the housing and the style of hinge. Each replacement lid will have a detailed photo som
view full answer...

What is the Retracted Height of the Brophy Scissor Steps # SS02
I spoke with my contact at Brophy about scissor steps # SS02. The retracted height is approximately 10 inches when installed. When extended, the height is 24 to 31 inches. These steps are designed as a universal fit item so they will most likely not fit the factory step mount and you will need to drill to mount them.
view full answer...

Ramp Spring Recommendation for a 33 inch Trailer Door
Since you have such a skinny door I would recommend you get a spring assist like the Ramp Spring # RS16933LH for the left side of the door and a Ramp Spring # RS16933RH for the right side. I attached a picture that shows how they will install.
view full answer...

Replacement Vent Cover for a 2008 Carry-On Enclosed Cargo Trailer
To determine if any of the vent covers that we carry will fit the vent on your 2008 Carry-On trailer, you will need to look at a few things. First, look at the opening size the vent assembly fits in. If it is approximately 14-1/4 inches square then that is a standard size. Next look at the hinge type. The hinge type is important to get the right replacement lid. The pictures on the product pages contain pictures of the hinges so you can compare them to what is on the trailer. There may also b
view full answer...

Which Roof Vent for 12 Foot Enclosed Trailer
The degree to which your roof is curved will dictate how well a 14x14 roof vent like the Ventline # V2092SP-28 will work for you. Since the roof is pretty thin, it might flatten enough so that a 14x14 vent could be installed. The mounting flange will need to sit flat to the roof. The # V2092SP-28 you referenced is a reasonably priced crank-out vent that includes a screen. It would work great for you, but you will need to determine how to get it to sit flat on your roof. You might find that y
view full answer...

How to Install the Surehoof Ribbed Rubber Trailer Mat # 3622RM
There is not a recommended method to installing the Ribbed Rubber Trailer Mat, # 3622RM. You could nail, tack, or glue the mat down to your trailer, it just depends on how you want to install the mat. I went out to the warehouse a pulled the mat to try to recommend a good installation method. This mat is made of heavy-duty rubber material and depending on what you use your trailer for, you may be able to just lay a couple strips without having to secure the mat to the ground. If you are
view full answer...

Ventline Vanair Trailer Roof Vent w/ Fan # VP-543SP for Box Truck
The Vanair Roof Vent with Fan you referenced, part # VP-543SP was originally designed for use on conversion vans, so it should be a great choice for your box truck. The vent will install into a 6-1/4 inch diameter rough opening. The garnish (or inner trim ring) allows the vent to be used on roofs of different thicknesses. Since your roof is so thin, you might need to trim some of the length off of the garnish which is fine according to the manufacturer. The installation kit which includes
view full answer...

Availability of Replacement Grip for Stromberg Carlson Lend-a-Hand Folding Grip Handle # AM-200
Our friends at Stromberg Carlson do not offer a replacement foam grip for the grab handle you mentioned. The good news is that the foam grip is the same type that is used on bike handlebars. The foam tube is an off-the-shelf item that you should be able to find at your local bike repair shop. Getting the foam tube on the handle is a little tricky, but spraying some aerosol hair spray on the metal tubing will act as a lubricant allowing the foam tube to be worked into the desired position. Onc
view full answer...

How Tall is the RV Manual Pull-Out Step, # SM-24-10, When in the Stowed Position
The overall height of the RV Manual Pull-Out Step, # SM-24-10, when in the stowed position is 6-3/8 inches from the top of the mounting surface on the step to the bottom most part of the assembly. There are actually some very useful dimensions in the link I have provided. I also made a picture that shows this dimension for you.
view full answer...

Installation Instructions for Enclosed Trailer Vent # 9106 and Stabilizer Trailer Jack # TJ01RT
There are no specific installation instructions for installing the Replacement Exterior Pop-Up Roof Vent, # 9106. You will need to cut a hole in the roof that is 11-1/8 inches long x 5-1/2 inches wide. You would need 12 screws, # 31071, to secure the vent and sealant # 0160297 to seal up gaps and holes. You can mount the Stabilizer Jack, # TJ01RT, two ways. The best way is to have the jacks welded to the trailer frame by a qualified professional. The alternative is to mount the jacks using yo
view full answer...

Installing Trailer Vent # V2092SP-28 on Snowmobile Trailer with 1/8 Inch Thick Roof
The garnish that is included with the V2092SP-28 is 2-1/8 inches thick, which is the shortest one offered. You can certainly use the vent, but you will have to modify the garnish or use some lumber to make a frame around the hole to take up some of the additional room. Due to the very thin roof, I would suggest making a frame as it would add some stability for the rough opening and provide a strong attachment point for the vent.
view full answer...

Overhead Clearance Necessary to Install Enclosed Trailer Ramp Spring # ERS160D96
According to our friends at Redneck Trailer Supply, the reel on the end of the Enclosed Trailer Ramp Spring, # ERS160D96 measures 5 inches in diameter, so you would need a bit more than 5 inches of room on the header above the rear door of your snowmobile trailer.
view full answer...

Will the Redline Greasable Hinge Pins HP12412G Fit on a 2006 Gearbox 335FS Toy Hauler
The Redline 1/2 Inch Greasable Hinge Pin, # HP12412G, is a great option to replace the missing hinge pins on your 2006 Gearbox 335FS toy hauler. These hinges are a universal fit item and include a grease zerk fitting for easy lubrication. If only some of your pins are broken, then you may want to measure the sizes of your remaining hinge pins so you can purchase the correct size replacements. We carry 1/2 inch and 3/4 inch hinge pins. I have attached a link to all of the hinge pins we carry.
view full answer...

How to Attach the Premium Horse Trailer Side Pad to the Trailer Wall
There is not a specific method for attaching the Horse Trailer Side Pad, # HTP60BK, to the trailer wall. You can use the Trailer Horse Pad Screw, # PS-8, but like you said it will puncture the material. Another option you have is to apply adhesive to one side of the horse pad to attach it to the trailer wall. I would recommend using a strong adhesive that can be purchased at your local hardware store. Be sure the back surface of the pad and the mounting surface of the trailer wall are cle
view full answer...

Order Tracking
Shipping Information
Contact Us
About Us

Help Videos and Articles
Search
Privacy Policy
Your Account Login