Select Your Vehicle

View Cart


Filter Questions and Answers:


reset filter
Trailer Hitch
Trailer Hitch
 

Expert Answers about Chrysler Trailer Hitch


  • Ball Mount Recommendation for 2013 Chrysler 300 with Curt Class III Trailer Hitch
  • For the Curt Class III Trailer Hitch # C13093 on your 2013 Chrysler 300, you will not need to use any specific ball mount. The ball mount you will want to use is the one that provides the correct rise or drop needed for you to tow your trailer level. I have attached a help article on how to determine the needed rise or drop for your trailer. A great ball mount kit option is the Ball Mount Kit for 2 Inch Hitches # 989900. This ball mount kit will provide you with a ball mount that...
    view full answer...

  • How to Determine Which Ball Mount Will Have Enough Rise for Curt Hitch on a 2005 Chrysler 300c
  • The best way to determine which ball mount is right for your 2005 Chrysler 300c and your trailer is to take a few simple measurements. Since you don't have the hitch we can see by the video of the Curt # 13465, I've attached, that the hitch receiver is going to be 10-1/4 inches from the ground. You will then want to take a similar measurement from the bottom of the coupler to the ground. Then compute the difference. If the hitch height is greater than the trailer height, then •hitch...
    view full answer...

  • Is a Special Wiring Harness Needed to Tow a Trailer with a 2001 Chrysler Town and Country
  • Your 2001 Chrysler Town and Country has what is called a separate or 3-wire lighting system. This means that the turn signals operate on different circuits/bulbs than the brake lights. But trailers use a combined system with the turn signals and brake lights on the same circuit (with few exceptions). So if you were to splice directly into the vehicle wiring then the light functions would not work properly on the trailer. So all you need to fix this is the proper wiring harness with a...
    view full answer...

  • Recommended Trailer Hitch And Wiring For 2012 Chrysler Town & Country
  • The trailer hitch and the trailer wiring harness are sold separately for your 2012 Town & Country. The trailer hitch I recommend for your vehicle is the Draw-Tite Trailer Hitch Receiver, part # 75579. This is a Class lll hitch and it has a 2 inch receiver opening. I recommend using a Class lll hitch versus a Class ll because there are many more accessories available for a 2 inch receiver. The trailer wiring harness I recommend is the T-One Vehicle Wiring Harness, part # 118534. You...
    view full answer...

  • Recommended Trailer Hitch and Towing Equipment - 2014 Chrysler Town and Country w/ Stow and Go Seats
  • Sure will! All the hitches we offer for the 2014 Chrysler Town and Country fit all models, regardless of if they have stow and go seats or not. The Curt Class III hitch # 13364 is a good choice, but if you're planning on using the hitch for hitch mounted accessories like a bike rack or cargo carrier, I'd choose a different hitch. Curt's hitch warranty stipulates that all non-trailer loads need to be supported with a stabilizing strap like # 18050. The Hidden Hitch and Draw-Tite Hitches...
    view full answer...

  • Class III Trailer Hitch Availability for a 2013 Chrysler Town and Country
  • For your 2013 Chrysler Town and Country we have the Curt Hitch # 13364 available that is a Class III hitch with a 2 inch opening confirmed as a fit. The price is available below at the attached link. I attached an install video as well. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2...
    view full answer...

  • Is Mounting Hardware Included With Curt Trailer Hitch For 2014 Chrysler Town And Country
  • Per the installation instructions for the Curt Trailer Hitch, part # 13364 that you received for your 2014 Town and Country, the vehicle's existing hardware is used to install the hitch. You need to make sure you do not misplace the hardware when removing it form your vehicle. Also, you will need a torque wrench like part # ALL644044 to tighten the hardware when installing the hitch. If you are unable to find all of the hardware needed for installation, we do offer the hardware kit....
    view full answer...

  • 2 inch Trailer Hitch Recommendation for a 2010 Chrysler Town and Country Stow and Go
  • Yes, the Curt Class III hitch part # 13364 that you referenced will fit your 2010 Chrysler Town and Country with Stow and Go seats as this hitch fits all models of the Town and Country. I attached an install video for you to check out as well. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball,...
    view full answer...

  • Recommended Trailer Hitch And Trailer Wiring Harness For 2015 Chrysler Town & Country
  • The trailer hitch I recommend for your Town & Country is the Draw-Tite Max-Frame Trailer Hitch Receiver, part # 75579. This is a Class llll hitch and it has a 2 inch receiver opening. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If...
    view full answer...

  • Fitment and Compatibility of Curt Hitch 13364
  • The Curt hitch # 13364 is confirmed to fit all models of Chrysler Town and Country between the years of 2008 to 2016.
    view full answer...

  • Towing Capacities and Trailer Hitch/Wiring Recommendations for a 2005 Chrysler Town and Country
  • There are a couple of weights to look at when determining how much trailer your 2005 Chrysler Town and Country can tow. First you need to consider the towing capacity of the vehicle itself or the gross trailer weight capacity listed for the vehicle. Additionally, Chrysler has a frontal area maximum that the trailer can have. They say that the front of the trailer cannot exceed 40 square feet. So if the trailer is 8 x 5 feet at the front or 10 x 4 feet, or any combination that adds up...
    view full answer...

  • Is Vertical Trailer Hitch Available For 2016 Chrysler 300S
  • The Valley Hitch, V81811 is designed for 2008 through 2010 Dodge Challengers and 300, but is not designed as a fit for your 2016 Chrysler 300S. We do not offer a vertical hitch for a 300S, but I have linked the trailer hitches we do have available you can check out. Valley is no longer in business so if you want a trailer hitch on your 300S I recommend a hitch like part # C13093. This is a Class lll trailer hitch and it has a 2 inch receiver opening. I have attached a link to an installation...
    view full answer...

  • Trailer Hitch and Wiring Harness Recommendation for 2013 Chrysler 200
  • To be able to transport your Permobil C300 electric wheelchair with your 2013 Chrysler 200 convertible, I recommend installing a trailer hitch and wiring harness on your vehicle and using a mobility chair trailer. The trailer hitch I recommend for you is the Hidden Hitch Class I Receiver Hitch # 60288. This hitch comes with the recommended drawbar to tow a trailer, as well as the needed pin and clip. A hitch ball compatible with the trailer coupler will be needed as well. You can use...
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Chrysler 200 S
  • Yes, Hidden Hitch trailer hitch # 60352 will fit your 2015 Chrysler 200 S. I have linked a video showing an example installation for you. This hitch comes with the appropriate ball mount, pin, and clip if you plan on towing. For a 1-7/8 inch ball I recommend # 19256 and for a 2 inch ball I recommend # 19258. And for trailer wiring I recommend # 118638 to add a 4-Way flat to the rear of the vehicle. If you want to use the hitch for an accessory such as a bike rack or cargo carrier...
    view full answer...

  • Is Bumper Trimming Required to Install a Trailer Hitch on a 2016 Chrysler Town and Country
  • Based on an installation we did of Curt hitch # 13364 on a 2016 Chrysler Town and Country you will not have to trim the rear fascia to install the hitch. However, it may press up some on the bottom of the fascia directly above the receiver. I have included a link to a video showing installation on a 2016 model for you. When installed the hitch measures approximately 13-1/4 inches for the ground to the top of the receiver opening. If measuring to the bottom of the receiver it would be...
    view full answer...

  • Will Trailer Hitch from 2011 Chrysler Town and Country Fit 2016 Town and Country
  • The Class III, 2 inch receiver, trailer hitches confirmed to fit the 2011 Chrysler Town and Country are also confirmed to fit the 2016 Town and Country. The Class III trailer hitches that will fit both vehicles are: Curt Class III Receiver Hitch # 13364 Draw-Tite Class III Max Frame Receiver Hitch # 75579 When installing a trailer hitch for the second time, new installation hardware should be used. For new hitch installation hardware, you can use # RHK and enter your trailer hitch's...
    view full answer...

  • Requirements to Tow Mobility Scooter Behind 2001 Chrysler PT Cruiser.
  • Based on my research, you can tow a trailer with your 2001 Chrysler PT Cruiser, but there are several warranty limitations. The owner's manual I found states to never exceed the gross axle weight rating of your vehicle because of the added weight of the trailer hitch's tongue weight or cargo weight. In order to comply with the vehicle's warranty, the following requirements must be met: -The max. frontal area of the trailer cannot exceed 20 sq. ft. -If your vehicle has a manual transaxle,...
    view full answer...

  • What Is The Difference Between Curt And Hidden Hitch Trailer Hitches For 2009 Chrysler PT Cruiser
  • You are correct that the instructions for the Curt hitch do require 4 bolts on each side, making that a total of 8 bolts for installation. Both of the hitches have been designed and tested for the weight capacities listed. Curt warranty does require the use of a stabilizing strap like part # 18050. The # C11132 and # 60818 are both Class l hitches with 2,000 lb towing capacity and 200 lb tongue weight capacity. I spoke with my contact at Hidden Hitch and they told me the reason...
    view full answer...

  • Trailer Hitch and Wiring Recommendation for a 2013 Chrysler Town and Country
  • First you would need to start with a trailer hitch for your 2013 Chrysler Town and Country. For that you would want the part # 13364. Since you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not include a ball mount...
    view full answer...

  • Trailer Hitch and Wheelchair Carrier Recommendation for a 2001 Chrysler Sebring
  • Class III hitches are reserved for larger vehicles like trucks and SUVs. For your 2001 Chrysler Sebring there are only Class I and II hitches available like the part # 36301 for if you have a Sedan and part # 24711 for if you have a convertible. Using a hitch adapter like what you described actually cuts the capacity of the hitch in half so I would not recommend that either. If the Sebring is your only tow vehicle option you would need to use a small trailer like the part # TLK864.
    view full answer...

  • Trailer Hitch Recommendation for a 2015 Chrysler Town and Country No Fascia Trimming
  • When we installed the Curt Hitch part # 13364 on a 2015 Chrysler Town and Country we didn't have to trim the rear fascia. We just let the hitch put slight pressure on the bottom of the fascia and it fit and worked well without trimming. See the install video I attached.
    view full answer...

  • Towing Capacity, Trailer Hitch, Wiring, and Transmission Cooler for a 2015 Chrysler Town and Country
  • The towing capacity of your 2015 Chrysler Town and Country is going to depend on a few factors. Take a look at the picture I have included from the owner's manual. It illustrates the capacity of the vehicle in certain scenarios. At most the van can tow 3,600 pounds. I do recommend a transmission cooler because when towing or even when just carrying a lot of weight in the van, it puts additional strain on the transmission. A supplemental cooler will help to lower the fluid temperature...
    view full answer...

  • Trailer Hitch and Wiring for a 2005 Chrysler Town and Country with Stow-N-Go Seats
  • Yes, Curt trailer hitch # C12289 will fit your Chrysler Town and Country with Stow-N-Go seats. If you plan on doing some towing the correct ball mount to use is # C45520. For a 1-7/8 inch ball use # C40001 and for a 2 inch ball use # C40018. And for trailer wiring use # 118300. I have linked videos showing example installations of the hitch and wiring for you. Curt also says you have to use stabilization strap # 18050 when using this hitch for any non-trailer load (such as a bike rack...
    view full answer...

  • Trailer Hitch Install Instructions and Install Video for a 2009 Chrysler Town and Country
  • I attached a link to an install video that shows the Hidden Hitch part # 87451 being installed on a 2009 Chrysler Town and Country as well as a set of install instructions that has all of the torque figures listed as well.
    view full answer...

  • What Vehicles will the Draw Tite Hitch # 36170 Fit
  • The Draw Tite hitch part # 36170 that you referenced will fit the following vehicles: 1993 - 1997 Chrysler Concorde 1993 - 1997 Chrysler Intrepid 1993 - 1997 Dodge Intrepid 1994 - 1997 Chrysler LHS 1993 - 1997 Eagle Vision 1994 - 1996 Chrysler New Yorker All Models
    view full answer...

  • 2015 Chrysler Town and Country Brake Controller and 7-Way Recommendation
  • You will need to start with a 4-way (if you do not have one). For that you would want the # C56150. Now if your trailer does not have brakes all you would need is the part # 37185 as an adapter to convert the 4-way to a 7-way. If you do have trailer brakes you would need the # ETBC7 instead of the # 37185 and a brake controller. This kit comes with everything needed to wire up the 7-way and install a brake controller. For a brake controller I would recommend the Prodigy P2 Brake...
    view full answer...

  • Replacement Installation Hardware for Curt Trailer Hitch and 2007 Chrysler Aspen
  • For replacement hardware to install Curt trailer hitch # 13702 on your 2007 Chrysler Aspen you will need # RHK. Enter the hitch number and manufacturer where indicated on the RHK page. I have also linked a video showing installation and the instructions incase you need those as well.
    view full answer...

  • Trailer Hitch and Wiring Recommendation for a 2013 Chrysler Town and Country
  • For your 2013 Chrysler Town and Country the Curt hitch part # 13364 has been confirmed as a fit and would work well for you. The Tow Ready wiring harness part # 118534 that you mentioned is a great option. We typically have better luck with the Tow Ready harnesses than the Curt ones anyway. I attached an install video for you to check out as well. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4...
    view full answer...

  • Recommended Trailer Hitch and Cargo Carrier To Carry Mobile Chair on 2002 Chrysler Sebring
  • The trailer hitch I recommend for your 2002 Chrysler Sebring is the Curt hitch part # C12186. This 1-1/4 inch trailer hitch has a 350 lb tongue weight capacity. All non-trailer loads - bike racks, cargo carriers and so forth - should be supported with a stabilizing strap like # 18050. If you need a cargo carrier to carry your mobile chair I recommend the Trailer Hitch Mounted Mobility Scooter and Wheelchair Carrier for 1-1/4" Hitches # RHWC1114. This carrier has a weight capacity of 230...
    view full answer...

  • Hitch and Bike Rack Recommendation for a 2011 Chrysler Town and Country
  • The Draw Tite hitch part # 75579 would work great for a hitch for your 2011 Chrysler Town and Country as it will fit all models including ones with stow and go seats. I attached an install video for you to check out as well. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike Rack part # S64670. This rack has a ton of positive reviews from our customers who have tried it. Check out the review video I attached for more info.
    view full answer...

  • Hitch Pin Hole to Bumper Dimension for Curt Hitch part # C12264
  • The distance from the center of the hitch pin hole of the Curt Hitch part # C12264 to the furthest point out on the rear bumper of your vehicle would be right at 5 inches. The most popular bike rack we carry that has been confirmed to fit this vehicle is the Swagman XTC2 Bike Rack part # S64670. This rack has a ton of positive reviews from our customers who have tried it. Check out the review video I attached for more info.
    view full answer...

  • Trailer Hitch and Wiring for a 2008 Chrysler Sebring Convertible with Dual Exhaust
  • Hidden Hitch trailer hitch # 60288 will fit your 2008 Chrysler Sebring convertible with dual exhaust. It can be used to tow a rental trailer. The hitch has a 2,000 pound gross trailer weight capacity but check the vehicle owners manual to the Sebring's capacity and go by whichever is lower. The hitch comes with the proper ball mount. To add a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring you can use # 118444 to add a 4-Way flat connector. I have...
    view full answer...

  • Trailer Hitch Recommendation for a 2013 Chrysler 200 with Dual Exhaust
  • The installation instructions for the Curt Class I receiver # C11133 specifically mention the procedure for installing the hitch on dual exhaust-equipped vehicles, to the hitch is indeed compatible with your vehicle. The procedure specific to dual exhaust vehicles is mentioned in step one of the instructions, which you can see by clicking on the link provided.
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Chrysler 200s
  • I spoke with my contact at Draw-Tite and he said that as long as it is a 2015 Chrysler 200 4-door sedan then trailer hitch # 24919 fits all models including the 200s. If you will be using the hitch for light duty towing then the correct ball mount is # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring you can use # 118638. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the...
    view full answer...

  • Multi-Ball Mount Recommendation for a 2007 Chrysler Town and Country
  • As long as you have a 2 inch hitch installed on your 2007 Chrysler Town and Country like the Draw Tite 75305 then yes, the Multi-Ball Mount part # C45650 would fit and work well for you.
    view full answer...

  • Trailer Hitch and Cargo Carrier Recommendation for a 2002 Chrysler Sebring
  • For a hitch for your 2002 Chrysler Sebring the Draw Tite hitch part # 36301 would work well for you as it has a 300 lb tongue weight capacity. This is a 1-1/4 inch hitch though. The Curt Cargo Carrier part # C18110 also has a 300 lb tongue weight rating and should work well for you as well. This carrier only weighs 30 lbs as well. I attached videos for both products I mentioned.
    view full answer...

  • Trailer Hitch and Wiring for a 2014 Chrysler Town & Country with Stow 'n' Go Seats
  • I am not sure why you are being asked about the trim level of your 2014 Chrysler Town & Country because the trailer hitches (at least the ones we carry) fit all models so it would not matter if it was a Touring model or something else. The most popular hitch for your van is # 13364. If you plan on doing some towing you might be interested in etrailer ball mount kit # EBMK4EL. It comes with a ball mount with a 2-3/4 inch rise or 4 inch drop, interchangeable ball set, hitch pin with clip,...
    view full answer...

  • Trailer Hitch for a 2008 Chrysler Town & Country with Stow 'n' Go Seats
  • Hidden Hitch trailer hitch # 87451 is listed as a fit for all models of the 2008 Chrysler Town and Country so that would include models that have the Stow n Go seats. I have linked the instructions and a video showing how the hitch installs. If you plan on doing some towing you might be interested in etrailer ball mount kit # EBMK4. It comes with a ball mount with a 2-3/4 inch rise or 4 inch drop, interchangeable ball set, hitch pin with clip, and a storage bag. If the ball mount...
    view full answer...

  • Is There a Difference Between the Hitch Receivers Offered for the 2007 Chrysler Pacifica 4.0
  • The three hitch receivers offered for the 2007 Chrysler Pacifica, Hidden Hitch # 87432, Curt # 13529, and Draw-Tite # 75522, are basically identical, have the same towing capacities, and will install in the same way. There really is no way to get around lowering the exhaust and removing your spare tire may ease the installation process so it is highly recommended. Some say that Curt hitches have a better powder coating but for the most part, price is going to be the main difference....
    view full answer...

  • Options for Carrying 6 Standard Bikes and One Tandem Bike on 2008 Chrysler Town and Country
  • I would recommend first installing a Class III trailer hitch like Draw Tite # 75579, which is a confirmed fit for your 2008 Town and Country. Then I recommend going with a 5-bike bike rack like the Thule Apex # TH9026. For womens bikes or bikes without a horizontal bar, I recommend the Thule Bike Adapter # TH982XT, which allows a bike without the horizontal bar to be transported in a more level position as well as increasing the ground clearance during transportation. For the remaining...
    view full answer...

  • Torque Rating for Hidden Hitch Class III # 87432 for 2004 Chrysler Pacifica
  • We don't publish the torque ratings for the fasteners, because the hitch manufacturers can change them. If you look at the bottom of page 2 of the instructions (see provided link), you'll see the torque rating for both the 1/2 inch and the M12 fasteners. The links pull the instructions directly from the manufacturer's websites, so they're always current. I'll also link you to an install video for the hitch. If you'll be using the hitch for towing, you might also be interested in the...
    view full answer...

  • Trailer Hitch and Bike Carrier for a 2008 Chrysler Sebring Hard Top Convertible
  • At the time the question you are referring to was answered the hitch # 90166 was listed as a fit for all models of the 2008 Chrysler Sebring. As you have found that has since changed rendering that answer irrelevant so I thank you for finding it and bringing it to my attention. Draw-Tite and Hidden Hitch are sister companies so hitch # 24871 and # 60288 (which DO fit the convertible!) are basically identical. They even share the same instructions. The difference is that the Hidden Hitch...
    view full answer...

  • Hitch Recommendation for a 2002 Chrysler Town and Country
  • I have a hitch solution I can recommend for your 2002 Chrysler Town and Country, but the Curt hitch part # C14355 that you referenced would work as was designed to fit newer Ford trucks. Instead you would want the Curt hitch part # C13362 as it has been confirmed as a fit for your vehicle. I attached a review video for you to check out as well. If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch...
    view full answer...

  • Hitch, Wiring, Cargo and Bike Rack Recommendations for 2005 Chrysler PT Cruiser Convertible
  • The Hidden Hitch Class I hitch # 60818 that you referenced is a confirmed fit for all versions of the 2005 Chrysler PT Cruiser. This light-duty hitch can be used with a 2-bike Class I hitch bike carrier, cargo carrier or to tow up to the vehicle's limit as specified in your owner's manual. I have included links to both bike racks and cargo carriers that are compatible with this hitch. I also linked articles that will help you select the best fit on your car and the best option for your...
    view full answer...

  • Trailer Hitch that is Mostly Hidden for a 2015 Chrysler 200
  • I included an image for the instructions for Draw-Tite trailer hitch # 24919. As you can see the receiver will be basically the only part visible. This is because it is welded to the bottom of the cross tube which is hidden. If you plan on doing some towing with the hitch on your 2015 Chrysler 200 then the correct ball mount to use is # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # 118638. If you want to use the hitch for an...
    view full answer...

  • Trailer Wiring and Hitch Recommendation for a 2007 Chrysler Town and Country
  • First lets start with a hitch for your 2007 Town and Country. If you have stow and go third row seats you would want the part # 87719, or if you do not have the stow and go seats part # 87717. I attached install videos for both hitches. For wiring you will want to first start with a 4-way. For that you will want the part # 118300. Now to convert it to a 7-way so that you can run a power wire to the trailer you will need the part # 37185. This will plug into the 4-way and then you will...
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Chrysler 200
  • There is an underbody panel that will need to be trimmed or removed to install la hitch on a 2015 Chrysler 200 but no bumper fascia trimming. I recommend Draw-Tite trailer hitch # 24919. It is the most popular option for your 200. I have linked the instructions for you to view. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited...
    view full answer...

  • Trailer Hitch and Wiring for a 2014 Chrysler 200 LX Sedan
  • Yes, you are correct. Curt makes their Class I and II hitches available by themselves or with one of three possible ball mounts. Hitch # C11133 is just the hitch. Hitch # C111331 is the hitch and a 1-7/8 inch diameter Euro-style ball mount. Hitch # C111332 is the hitch and a 2 inch Euro-style ball mount. And hitch # C111333 is the hitch plus the appropriate ball mount but no ball. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring you can use...
    view full answer...

  • 1-1/4 Inch Trailer Hitch and Wiring for a 2016 Chrysler Town and Country
  • Yes, you can install a 1-1/4 inch trailer hitch on your 2016 Chrysler Town and Country. I recommend Draw-Tite trailer hitch # 36455 which is a Class II hitch with a 1-1/4 inch receiver. I have included a link to a video showing an example installation for you. If you want to do some towing I recommend ball mount # 36061. It includes a pin and clip. For a 1-7/8 inch ball I recommend # 19256 and for a 2 inch I recommend # 19258. For trailer wiring I recommend # 118534 to add a 4-Way flat...
    view full answer...

  • How to Transport Bikes with a 2005 Chrysler PT Cruiser Convertible
  • For the 2005 Chrysler PT Cruiser I have a solution that will allow you to transport bicycles, but there are no trunk racks confirmed to fit the convertible models. Instead you would want a hitch mounted option. For a hitch the # 24759 has been confirmed to fit all models of the PT Cruiser so it would work well for you. The Swagman XTC2, part # S64670 is one of the most popular racks because it's so easy to use, and because the rack has an angled shank that would raise the bike rack...
    view full answer...

  • Trailer Hitch and Wiring for a 2015 Chrysler 200
  • The instructions for Hidden Hitch trailer hitch # 60352 are linked here and on the product page. Links appear on the right hand side of pages. Look for the black and white wrench icon. The Hidden Hitch model comes with the proper ball mount, pin, and clip. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # 118638. Its instructions are also linked here and on its page.
    view full answer...

  • Hitch Recommendation for a 2013 Chrysler 200
  • The Curt hitch part # C11133 that you referenced has been confirmed to fit the Sedan and Coupe models of the 2013 Chrysler 200 so it should work well for you. I attached an install video for you to check out as well. The Curt hitch comes with the correct ball mount, hitch pin, and clip. For a ball you can use # 19256 for 1-7/8 inch diameter or # 19258 for a 2 inch diameter. For trailer wiring, use T-One Vehicle Wiring Harness, # 118550. I have included a link to the installation...
    view full answer...

  • Ground Clearance at Rear of Vehicle after Hitch Install on a 2012 Chrysler Town and Country
  • The Mopar hitch for your 2012 Chrysler Town and Country couldn't sit any higher than the Curt Hitch part # 13364 would as this hitch tucks right under the rear bumper. The # 13364 will give you about 12 inches of clearance, and since there is no way an OEM hitch could sit up any higher than this one this would be your best option since it is most likely less expensive.
    view full answer...

  • Hitch Recommendations for 2005 Chrysler Town and Country w/ Stow and Go Seats
  • When you search by vehicle, the page you'll be taken to has a drop down menu at the top where you can choose Town and Country models 'with Stow-N-Go seats' or 'without Stow-N-Go seats'. The Draw-Tite Class III receiver hitch, part # 75305 would make a good choice. The hitch is indeed compatible with vehicles with stow-n-go seating. If you'll be using the hitch for towing, you'll need the following to complete your towing set-up: Trailer wiring harness with 4-pole trailer connector,...
    view full answer...

  • Mounting Hole Dimensions for the Hidden Hitch part # 90718
  • The hitch part # 90718 that you referenced has mounting hole dimensions that are 50 inches apart for the inner mounting holes on the bracket nearest to the rear of the vehicle, 55 inches from the outer most mounting holes on the same bracket, and then 52-3/4 inches between the holes of the brackets closer to the front of the vehicle.
    view full answer...

  • Replacement Installation Hardware for a Trailer Hitch on a 2013 Chrysler 200
  • Yes you can get just the installation hardware for the trailer hitch for your 2013 Chrysler 200. You will need # RHK. Enter in the hitch number where indicated on that page then select the manufacturer of the hitch you have and the correct hardware kit will be assembled for you. If you are not sure of the hitch you have I have included a link to all of the hitches for the 2013 Chrysler 200.
    view full answer...

  • Recommended Trailer Hitch For 2012 Chrysler Town And Country
  • We do offer some Class lll hitches for a 2012 Chrysler Town and Country. I did some research on your van and found that the trailer towing weight for your Town And Country is 3,600 lbs, and is 3,500 lbs if you have the Stow-N-Go seating. The trailer hitch I recommend is the Curt Trailer Hitch, part # 13364. This is a Class lll hitch and has a 2 inch receiver opening. You will want to consider where the receiver end is under your van when you want to install any accessories like...
    view full answer...

  • What Vehicles Does the Curt Hitch part # 13364 Fit
  • The Curt Hitch part # 13364 that has been confirmed to fit your 2013 Chrysler Town and Country fits the following vehicles: 2012 - 2014 Dodge CV 2012 - 2015 Ram CV 2008 - 2015 Dodge Grand Caravan All Models 2009 - 2012 Volkswagen Routan All Models 2008 - 2015 Chrysler Town and Country All Models
    view full answer...

  • Trailer Hitch Availability for 2005 Chrysler Town & Country Minivan
  • We do offer trailer hitches for your 2005 Chrysler Town & Country Minivan. In fact for your van we offer three different classes of hitch, from light-duty 1-1/4-inch Class I types like the Draw-Tite # 24702, to higher capacity Class II types such as the Curt # C12362, and also 2-inch Class III types such as the Hidden Hitch # 87717. You can choose the hitch based on your intended purpose - whether to hold a cargo carrier or to pull a trailer - and also based on whether your van has the...
    view full answer...

  • Hitch and Wiring Recommendation for a 2008 Chrysler Sebring Convertible
  • First let's start with a hitch. For that I would recommend the Hidden Hitch part # 60288 that comes with a ball mount and a hitch pin and clip. For trailer wiring you would want the # 118444, and then for a hitch ball you would want either the # 19256 or # 19258.
    view full answer...

  • Trailer Hitch Availability for 2008 Chrysler Sebring V6 Convertible
  • We do offer two options in a light-duty 1-1/4-inch Class I trailer hitch for your 2008 Chrysler Sebring V6 Convertible. Please note that the part you referenced, Draw-Tite Class II hitch # 36448, is a fit only for the sedan, not your convertible. The link at right will show you both hitch options we can offer. Since both carry identical weight ratings I suggest the lower-cost Draw-Tite # 24871 if you will be using a bike rack or cargo carrier and Hidden Hitch # 60288 if you will be towing,...
    view full answer...

  • How Far Recessed from Bumper is Draw-Tite Hitch # 36455 Installed on 2011 Chrysler Town and Country
  • In the installation video for Draw-Tite hitch # 36455, which I have linked for you at right, you can see the position of the installed hitch at the 1:20 mark. This shows an underside view of the 2011 model year's rear bumper after hitch installation. I have also linked a screen shot image with an arrow to indicate the distance between the edge of the receiver tube and the rear edge of the bumper - just about 5-inches. You can use this measure to compare to the clearance provided by your...
    view full answer...

  • Trailer Hitch for a 2015 Chrysler 200
  • Yes, I can email you the installation instructions for Hidden Hitch trailer hitch # 60352 and Draw-Tite trailer hitch # 24919. These hitches actually share the same instructions. The difference is that the Hidden Hitch model comes with a ball mount, pin, and clip. Installation is not difficult at all on your 2015 Chrysler 200. If you plan on doing any towing first consult the vehicle owners manual to make sure it is permissible to do so. If you can tow then go with Hidden Hitch model...
    view full answer...

  • Hitch Recommendation for a 2004 Chrysler Town and Country
  • For a hitch for your 2004 Chrysler Town and Country I would recommend the Hidden Hitch part # 87717. This hitch has a 2 inch opening which means it will have more capacity than the smaller hitches and will have more options for hitch accessories. For trailer wiring you would want the part # 118300. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch...
    view full answer...

  • Hitch Recommendation for a 1999 Ford Windstar and a 2000 Chrysler Town and Country
  • A hitch from a 2000 Chrysler Town and Country would not fit on a 1999 Ford Windstar. For the Town and Country you would want the part # 36296. For the Windstar you would want the part # 75055. I attached install videos for both hitches to the right.
    view full answer...

  • Trailer Hitch for 2005 Chrysler PT Cruiser
  • We do offer several brands of light-duty 1-1/4-inch Class I trailer hitches for your 2005 Chrysler PT Cruiser, including the Curt # C11132 that you referenced. The link at right will show you all options. The Curt hitch is the one of the three that does not require drilling, but otherwise all three hitches will install in an essentially identical manner using included hardware. I have linked you to an installation video for the Hidden Hitch # 60818 and also to two helpful hitch installation...
    view full answer...

  • Hitch Recommendation for a 2010 Chrysler Town and Country
  • There was a generation change between your 2006 Chrysler Town and Country to your 2010 model so the hitch from your 2006 would not fit your 2010 model. Instead I would recommend the 2 inch hitch part # 75579. 2 inch hitches will have more capacity and more hitch accessories like bike racks and cargo carriers are designed to fit them as well. I attached an install video for you to check out as well. For trailer wiring you would want the part # 118552. For ball mounts I recommend...
    view full answer...

  • Modifications Needed to Install Hidden Hitch Trailer Hitch Receiver on a 2014 Chrysler 300
  • According to the installation instructions for the Hidden Hitch Class II trailer hitch, part # 90209, there is no cutting or modification required. I linked the instructions to the right. The ball mount, pin and clip are included. I have included a picture to give you an idea of how visible the hitch will be. There is a Curt connector vehicle harness available # C56145. The hitch balls recommended are 1-7/8-inch # 19256 or the 2-inch # 19258. I have included a installation video for...
    view full answer...

  • What is the Best Trailer Hitch and Wiring for a 2014 Chrysler 300 Base Model with 3.6 Liter Motor
  • Yes, Curt trailer hitch # C13093 fits all models of the 2014 Chrysler 300 including the base models. If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag. If the ball mount kit does not have the right rise or drop to tow the trailer level,...
    view full answer...

  • How to Carry 4 Bikes on a 2005 Chrysler PT Cruiser with a Class I Trailer Hitch
  • The use of an adapter to go from a 1-1/4 inch trailer hitch to a 2 inch receiver will reduce the tongue weight capacity of the hitch by 50 percent. The other issue is that all of the trailer hitches for your 2005 Chrysler PT Cruiser are Class I trailer hitches. Class I trailer hitches are rated for a maximum of 2 bikes. This is actually something that both hitch and bike rack manufacturers agree on. To carry 4 bikes you can carry 2 bikes using the trailer hitch but the other bikes will...
    view full answer...

  • Modifications Needed for 2014 Chrysler 300S To Install Class II Trailer Hitch
  • According to the installation instructions for the Hidden Hitch Class II trailer hitch, part # 90243, there is no cutting or modification if the bumper fascia required (see linked instructions). However, on 2011 and newer vehicles, there's a plastic appearance panel under the vehicle that would need to be removed and left off the vehicle. There is a trailer wiring harness available, part # C56145. The hitch I recommended includes the ball mount and the pin and clip, but you'd also need...
    view full answer...

  • Trailer Hitch and Wiring Recommendations for a 2014 Chrysler 200 Limited
  • Yes, the Draw-Tite trailer hitch # 24871 will fit your 2014 Chrysler 200 Limited. It will fit all models including the convertible models. If you plan on doing some towing please first consult the owners manual to determine the towing capacity of the vehicle. For a ball mount use # 3594. And for a 1-7/8 inch ball use # 19256. For a 2 inch ball use # 19258. For trailer wiring you can use # 118577. I have linked the installation instructions for the hitch and wiring and a video showing...
    view full answer...

  • Hitch and 4-Bike Rack Recommendation for 2006 Chrysler Town and Country with Stow-n-Go Seats
  • Your 2006 Chrysler Town and Country with Stow-N-Go seats can be fitted with either of two classes of trailer hitch: a 1-1/4-inch Class II or a higher-capacity 2-inch Class III type. I suggest a 2-inch Class III hitch since you will using a 4-bike capacity rack which can have substantial weight when loaded. The most popular hitch for your vehicle is the Hidden Hitch # 87719 which has a 2-inch receiver opening. I have included an installation video as well as two helpful articles with...
    view full answer...

  • Hitch Recommendation for a 2014 Chrysler Town and Country that Doesn't Require Fascia Trimming
  • Draw-Tite trailer hitch # 75579 will fit all models of the 2014 Chrysler Town and Country. There should be no bumper fascia trimming required. The only trimming mentioned in the instructions, linked to the right, is possibly on a mudflap. I have also included a link to a video showing a typical installation for you. The Curt Hitch part # 13364 that you referenced would most likely require you to trim the fascia so I would not recommend it for you. If you plan on doing some towing...
    view full answer...

  • 7-Way Mounting Bracket Recommendation for a 2011 Chrysler Town and Country with Curt Hitch
  • Due to how tight your hitch opening sits to the bumper of your 2011 Chrysler Town and Country I have a solution for you, but the Curt Bracket part # C58000 would not be it. Instead I would recommend the 7-Way Trailer Connector Mounting Box # 18159. This will strap around the cross beam of the hitch and will provide an excellent mounting bracket for your 7-way.
    view full answer...

  • Hitch Recommendation for 2010 Chrysler Town and Country Minivan
  • Your 2010 Chrysler Town and Country minivan can be equipped with either a 1-1/4-inch Class II or a 2-inch Class III trailer hitch. All options are shown on the link provided. I suggest the Class III hitch # 13364 from Curt; this is the most popular hitch for your vehicle. This 2-inch hitch will offer better compatibility with a broad range of hitch mount accessories like cargo carriers and bike racks, and if you will be towing it will provide higher capacity than the Class II hitches....
    view full answer...

  • Can a 2007 Chrysler Town and Country Tow a 2,850 lb Popup Camper
  • A Class II trailer hitch would have enough towing capacity to pull your pop up camper, but we will want to make sure your 2007 Chrysler Town and Country is capable of towing that weight. According to the owners manual, your Town and Country would only have enough towing capacity to pull your camper if it came with a factory tow package If it did not come with a tow package, the maximum towing capacity is 1,800 lbs. To determine if your van came with the tow package, I recommend contacting...
    view full answer...

  • Suspension Enhancement Recommendation for 2002 Chrysler Town and Country Carrying Mobility Scooter
  • The total weight of your what you plan on carrying is below the capacity of the Curt Trailer Hitch Receiver # C13362 that you referenced. However, you still want to check the owners manual of your 2002 Chrysler Town and Country to determine what the tongue weight capacity of your vehicle is and be sure not to exceed this figure as well. Suspension enhancement would be a great option if you do experience sag. You should note that this will not increase the tongue weight capacity of your...
    view full answer...

  • Recommended Hitch and Related Towing Components for 2008 Chrysler 300
  • Two sizes and weight classes of hitch are offered for your 2008 Chrysler 300. These include several of the 1-1/4-inch Class II type and one of the 2-inch Class III type. All things being equal I suggest the 2-inch Class III hitch # 13465 from Curt since this size hitch will be more widely compatible with a range of hitch-mount accessories like bike racks and cargo carriers. But if those things are not in your plans then the 1-1/4-inch Class II Hidden Hitch # 90243 is a great choice as it...
    view full answer...

  • Trailer Hitch Recommendation For 2012 Chrysler Town And Country
  • For your 2012 Chrysler Town And Country the hitch I recommend is the Curt Hitch, part # 13364. This is a Class lll hitch with a 2 inch receiver opening. I have attached an installation video for this hitch on a 2012 Town And Country you can check out. We are located in the Midwest but ship throughout the US. If you would like to speak with one of our good folks in Customer Service about shipping you can reach them at 800-298-8924.
    view full answer...

  • Will Draw-Tite Hitch # 24871 Fit the 2013 Chrysler 200 and Work With a 2-Bike Class I Hitch Carrier
  • Draw-Tite Hitch # 24871 is indeed a correct fit for your 2013 Chrysler 200 with dual exhaust. This light-duty Class I hitch fits both sedan and convertible models. With this 1-1/4-inch installed (it bolts into place - no drilling and no welding) you can use a compatible 2-bike Class I bike carrier. Do please note that Class I hitches can only handle the load of 2 bikes, even if the carrier itself can hold more. The linked article on hitch classes will explain in detail. I have also...
    view full answer...

  • Are 5 Bolts Enough to Safely Install Curt Trailer Hitch 13364 on a 2014 Chrysler Town and Country
  • Apparently, on the 2014 Chrysler Town and Country, on the passenger side frame rail there is a bolt that is holding on the bumper and it should not or cannot be removed. Otherwise there would likely be 6 bolts instead of 5 holding on Curt trailer hitch # 13364. The sheer strength of the bolts, even though there are just 5 of them, is more than enough to handle the horizontal pulling force of towing a trailer. The clamp strength of all of the bolts is more than enough for the tongue weight...
    view full answer...

  • Recommendation for 2 Inch Trailer Hitch Receiver on 2008 Chrysler Town and Country Stow and Go
  • I would recommend the Curt Class III Receiver Hitch, # 13364, for your 2008 Chrysler Town and Country Stow and Go. This 2 inch hitch has a maximum trailer weight capacity of 4,000 pounds and tongue weight capacity of 400 pounds and mounts directly to the frame with no welding required. If you plan to tow and need wiring to operate lights on a trailer, the Curt Wiring Harness, # C56162, can be plugged directly into your vehicle's factory connectors with no cutting or splicing needed....
    view full answer...

  • Availability of Trailer Hitch for 2000 Chrysler Concorde
  • Curt offers a Class II hitch that is a fit for the 1998-2001 Chrysler Concorde, part # C12032. If you're planning on using the hitch for towing purposes, you'll need the following to complete your towing system. Ball mount, part # C45521 2 inch trailer ball, part # A-82 1-7/8 inch trailer ball, part # A-80 Pin and clip, part # PC3 Locking hitch pin, part # 40107 Trailer wiring harness, part # 118364
    view full answer...

  • Does Fascia of 2012 Town and Country Need to be Trimmed to Install Curt Trailer Hitch # 13364
  • I spoke to my contact at CURT who said some minor trimming of the fascia is required for the hitch installation on your 2012 Town and Country, otherwise the receiver will impinge on the bumper cover. The area that needs to be trimmed is 2-3/4 inch wide by 1/2 inch tall. I have included a diagram of the area that needs to be trimmed as well as a link to installation details. The Hidden Hitch # 87451 is a Class III trailer hitch that will not require trimming. I have linked the...
    view full answer...

  • Hitch, Wiring and Ball Mount Recommendation for a 2013 Chrysler Town and Country
  • For a trailer wiring harness for your 2013 Chrysler Town and Country to go along with the Curt Hitch part # 13364 that you referenced I would recommend the Curt Wiring Harness part # C56150. This is a protected unit that would install by plugging in line with your vehicle taillights and then running a wire up the positive side of your vehicle battery. Check out the install video I attached. To complete your towing setup you may also be interested in purchasing a etrailer.com Ball Mount...
    view full answer...

  • Will a Trailer Hitch Mount Bike Rack Affect Park Assist Sensors on a 2012 Chrysler 300s
  • It is likely that anything mounted in Curt trailer hitch # C13093 would set off the park assist sensors on your 2012 Chrysler 300S. However, if your vehicle is anything like mine (I have a backup camera and alert system) it would only be an issue when you are backing up. It is possible that a bike rack alone would not trip the sensors. But with bikes loaded it is almost certain that they will. You may be able to adjust the angle of the sensors to make them less likely to sense the...
    view full answer...

  • Does Draw Tite Hitch part # 36455 Require Fascia Trimming like Curt Hitch for 2012 Town and Country
  • I think the Draw-Tite Hitch part # 36455 would be your better option. There is not fascia trimming required with this hitch being installed on your 2012 Chrysler Town and Country and if you were to carry a bike rack on the hitch you would not be required to use a stabilizer strap like the Curt hitch # 13364 requires. I attached a link to an install video and instructions for you to check out as well.
    view full answer...

  • Availability of Trailer Hitch Receiver for Towing with 2008 Chrysler Sebring Hard-Top Convertible
  • We do offer two light-duty Class I trailer hitch receivers for the 2008 Sebring hard-top convertible and both can be seen on the link provided. The hitch # 36448 that you referenced is not a fit for your convertible, only for the sedan version of the Sebring. The correct Draw-Tite hitch is # 24871. I have linked an installation video for your reference as well as the written instructions. Please note that according to a Chrysler Corporation document I located online not all versions...
    view full answer...

  • What is the Capacity of Curt Trailer Hitch 11132 for a 2007 Chrysler PT Cruiser
  • I am not sure what you mean by system rating but the Curt trailer hitch # C11132 is rated for 200 pounds tongue weight and 2,000 pounds gross trailer weight. I have included a link to the installation instructions for you to view. Be sure to consult the vehicle owners manual for its towing capacities. Always go by the lower rating. The hitch meets Regulation V-5 and SAE J684 regulations. If you plan on towing with this hitch the correct ball mount to use is # C45520 with pin and clip...
    view full answer...

  • Will Hidden Hitch Trailer Hitch 87432 Fit a 2004 Chrysler Pacifica with Full Size Spare Tire
  • I spoke with my contact at Hidden Hitch about hitch # 87432. He stated that the full-size spare tire on the vehicle will not be a problem. It will be easier to install the hitch if you remove the spare but after the hitch is installed the tire will go back into place. If you plan on doing some towing I also recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a storage bag. For trailer wiring if needed use # 118303. I have included...
    view full answer...

  • Is Trimming Required to Install a Draw-Tite Trailer Hitch on a 2013 Chrysler Town and Country
  • Draw-Tite trailer hitch # 75579 will fit all models of the 2013 Chrysler Town and Country. There should be no bumper fascia trimming required. The only trimming mentioned in the instructions, linked to the right, is possibly on a mudflap. I have also included a link to a video showing a typical installation for you. If you plan on doing some towing then I also recommend etrailer ball mount kit # EBMK4EL. it comes with the proper extra long ball mount, interchangeable ball set, hitch...
    view full answer...

  • Trailer Hitch and Wiring for a 2004 Chrysler Town and Country
  • We do have several trailer hitches that will fit the 2004 Chrysler Town and Country including # 90165. I have included a link to the right with the hitches that will fit your van. If you plan on doing some towing then for a 1-7/8 inch ball use # 19256 and for a 2 inch use # 19258. And for a plug and play type of wiring harness use # 118300. I have linked videos showing installations of the hitch and wiring for you.
    view full answer...

  • How Does a Curt Stabilizing Strap Work and Install
  • I think the easiest way for me to explain how a Curt Stabilizer Strap part # 18050 would install and be used would be to direct you to a demonstration video we have for this product. Check it out, basically you attach the strap to the cargo carrier or bike rack and then run it to the lip of the hatch or trunk and it helps brace the load when going over bumps.
    view full answer...

  • Trailer Hitch is Rated Higher than Towing Capacity of 2005 Chrysler 300 with 2.7L V6
  • The important thing to remember is that the trailer hitch is rated for 3,500 pounds. If the vehicle is rated lower, which in this case it is, you go by the lower rating. You would not want to go beyond the capacity specified in your vehicle owners manual. I have included a link to a video showing a typical installation for you. I have also included a link to the installation instructions. Since you are planning on doing some towing I recommend the etrailer ball mount kit # EBMK4. It...
    view full answer...

  • Trailer Hitch and Wiring for a 2008 Chrysler Sebring with 2.7 Liter Engine
  • I found a copy of the owners manual online for the 2008 Chrysler Sebring and found that with the 2.7 liter motor the vehicle is rated to tow up to 1,500 pounds gross trailer weight and 150 pounds tongue weight. Confirm this in your owners manual. To determine the cost of the parts only from etrailer, you will just need to click on the items, linked below, and the price will be on the product page for each item. For a trailer hitch I recommend the Hidden Hitch Class II hitch # 90166....
    view full answer...

  • Trailer Hitch and Bike Rack Recommendations for a 2013 Chrysler Town and Country
  • First, if you need a trailer hitch, I recommend the Hidden Hitch # 87451. This is a Class III trailer hitch that will afford you many bike rack options. I have linked the instructions and I have linked a video showing a typical installation for you. For a bike rack, if access to the rear hatch is important to you, I recommend the Thule Vertex swinging rack, # TH9031XT. It will hold 4 bikes like you need but has the added bonus of being able to swing out to the side of the van to allow...
    view full answer...

  • Will Curt Trailer Hitch # 11132 Fit a 2006 Chrysler PT Cruiser Convertible
  • The Curt Trailer Hitch, # C11132, will fit all models of the 2006 Chrysler PT Cruiser which would include your convertible. I have included a link to the instructions for you. If you plan on doing some towing, the correct ball mount is # C45520 and you can use pin and clip # PC2. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # 118462. I have linked the instructions and a video showing a typical installation of the wiring.
    view full answer...

  • Installing Draw-Tite Trailer Hitch 36274 on a 2004 Chrysler Concorde
  • The 2004 Dodge Intrepid uses a different hitch than the 2004 Chrysler Concorde, so the installations might be close but they would not be exactly the same. Take a look at the installation instructions I have linked for hitch # 36274. They should give you the best idea of how the installation will go.
    view full answer...

  • What is the Towing Capacity of a 2009 Chrysler Sebring with 2.4 Liter 4 Cylinder Engine
  • I found an owners manual online for the 2009 Chrysler Sebring and found that the vehicles with the 2.4 liter engine can tow up to 1,000 pounds gross trailer weight and 100 pounds tongue weight. The towing section starts on page 338 in the manual. This does limit what you can tow quite a bit so I do recommend a different towing vehicle since you will not get much of a camper under 1,000 pounds. If you do plan on towing with this vehicle then you can use hitch # 60288. It comes with...
    view full answer...







Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviews etrailer.com reviews

All images, layout and content copyright etrailer.com