Expert Answers about Hitch Bike Racks dimensions

Hitch Bike Racks

Expert Answers about Hitch Bike Racks

What is the Weight Capacity of the Swagman Titan Trailer Hitch Mount 4-Bike Rack
On the Swagman Titan, # S63410, the single bike capacity is 35 pounds. The capacity of the rack as a whole is 100 pounds. So if you had four 30 pound bikes loaded that would exceed the capacity of the rack, you are correct. We have other 4 bike racks that can accept more weight. The Thule Vertex, # TH9029, for example can handle 140 pounds total (35 pounds per bike). But with its straight shank, the Vertex is not going to offer any additional ground clearance. I have included a link to a vide
view full answer...

Does a 2005 Honda 2005 Honda Odyssey EX-L Have Enough Tongue Weight For Thule Apex # TH9027
In my research, I have found that a 2005 Honda Odyssey with a tow package and 2 inch receiver has a tongue weight of 350 pounds, however, the owners manual will give you the exact weight limits and should be the final authority. You should have enough capacity for both the bike rack and the bikes, providing your owners manual states you have enough capacity and you do not exceed the capacity of the lowest rated component in your setup.(bike rack or hitch) If you are planning on carrying ei
view full answer...

Carrying More Than 2 Bikes with Class I Hitch on 2010 Honda CR-V
The hitch and bike rack manufacturers all agree that a bike rack installed in a Class I receiver should be limited to two bikes. The weight is not the only issue, any additional bikes added will put the load of the rack and the bikes further away from the receiver opening. As this distance increases, so does the leverage applied to the hitch and its attachment points to the vehicle. This leverage can bend and eventually break the hitch or cause the hitch attachment points to the vehicle to fail.
view full answer...

What is the Total Length of the Rhode Gear Highway Trailer Hitch Mount Bike Rack
We have one of the Rhode Gear Highway 4 bike racks, # RG8015221, in our show room here so I went down to measure the distance from the center of the hitch pin hole all the way out to the end of the arms. The total distance is 35-1/4 inches. If the extension is a concern then you might be interested in the Advantage SportsRack TiltAWAY 4 Bike Carrier, # HE3010. Not only do the ends of the arms have reflectors, but when not loaded, you can fold the arms down. I have linked a video review of the
view full answer...

Options for Carrying 3 Bikes on a 2013 Hyundai Elantra GT with a Class I Trailer Hitch
There may be a way to carry 3 bikes on your 2013 Hyundai Elantra GT, however, a class I trailer hitch can only support a maximum of 2 bikes on a hitch mounted bike rack. I would recommend using the Thule Helium 2 Bike Rack, # TH970XT, and mounting the third bike on the roof of your vehicle as long as you do not have the panoramic sunroof. You could stay with the Helium 3 Bike Rack, # TH971XT, if you plan on using the Helium on another vehicle with a class II, III, or IV trailer hitch, but yo
view full answer...

Will a Surly Moonlander Mountain Bike with 4.7 Inch Thick Tires Fit the Rola NV2 Bike Rack
We are waiting to hear back from Rola to determine if the NV, # 59508, is a good option for your Surly Moonlander bike. But in the meantime we have determine the length of the strap from the base to the furthest hole is approximately 7-1/2 inches. This should be plenty long enough to secure around the tires on the bike. Also since the straps are rubber they can stretch. I have included a link to a video review of this bike rack for you.
view full answer...

How To Calculate Tongue Weight on Hitch When Using Swagman Original Towing Bike Rack # S64600
The weight of the Swagman Original Towing Bike Rack, part # S64600, is 23 lbs. The bike rack can handle a maximum of 3 bikes with a maximum weight capacity of 35-lbs per bike (105 lbs total). That would total 128 lbs of tongue weight on your vehicles hitch if you were hauling three bikes on the rack. That would leave you 372 lbs of tongue weight still available on your hitch for towing. I am including a link to the installation instructions on the bike rack.
view full answer...

Dimensions of Tubing Used to Construct Swagman # S64955 Bike Rack
The upright tubing of the Swagman # S64955 measures 2 inches in diameter. At the rear, the rack is right at 36 inches tall. You can see these measurements in the photo I have edited for you.
view full answer...

Length of Hollywood Racks Commuter Hitch-Mounted Bike Rack # HR2500 Receiver Tube
After speaking to my contact at Hollywood Racks, I have confirmed the length of the receiver tube you referenced for the Hollywood Racks Commuter Hitch-Mounted Bike Rack #HR2500 is 10-1/4 inches from the center of the pinhole to the back of the mast (upright bar) on the rack. I have included a graphic showing the exact measurements and I have included a link to the instructions for the proper installation of this product on your 2012 Nissan Juke. If you plan to carry womens bikes or alternati
view full answer...

Ground Clearance Provided with Rola NV2 Bike Rack on 2009 VW GTI
Since the Rola NV2 holds the bike to the rack by the wheels, the wheel diameter of your bike will determine how much if any the bike tires will extend below the level of the hitch receiver. If you take a look at the photo I edited for you, you can see a typical mountain bike with 26 inch diameter wheels placed on the rack. As you can see, the tires do not extend lower than the lowest portion of the rack. A bike with larger diameter wheels would hang a bit lower. Since a WV GTI has limited
view full answer...

Overall Length the Hollywood Racks Sport Rider SE Trailer Hitch Mount Bike Rack Extends
On the Hollywood Racks Sport Rider SE, # HR1400, it measures 43 inches from the face of the trailer hitch receiver to the center of the last wheel hoops on the rack. It is another 3 inches or so to the very end of the rack but the handle bars on the bike will stick out further. I have included links to the instructions and a video for you to view.
view full answer...

Distance Between Wheel Cradles Front to Back on the Swagman Quad Trailer Hitch Mount Bike Rack
That actually is not a common measurement but I can see how it would be useful. Also, I would add that the bikes when placed on the rack alternate which direction they face so the handle bars (widest part of the bike) will not be right next to each other. I went out to the warehouse and personally assembled the Swagman Quad, # S64690, to take the measurements. The distance from the center of the first wheel cradle to the second wheel cradle is 10 inches. It is the same between the third and f
view full answer...

Using Swagman G2 # S64680 in Front Mount Receiver on 2006 Chevy Silverado
The angled shank of the Swagman G2 # S64680 will raise the platform up by 4 inches from the top of the receiver to the bottom of the platform. When deployed, the wheel trays will measure 20 inches laterally from the hitch pin hole in the shank. To determine if you will have sufficient visibility with the rack installed, add about 4 inches to the height of your bikes, and measure that distance upward from the top of the front receiver. You should also determine if the width of your bikes will
view full answer...

Ground Clearance on the Thule T2 Trailer Hitch Mount Bike Rack on a 2011 Subaru Outback Wagon
Because of the way the Thule T2, # TH916XTR, is designed, there is actually a rise of 4-3/4 inches from the top of the receiver opening on the trailer hitch to the bottom of the nearest platform. The rack angles up even more towards the back and the bottom of the furthest end from the receiver is 3/4 inches higher. Based on this rise you will not have to worry too much about ground clearance unless you are on steep grades or go over severe bumps or dips. I have included a link to the inst
view full answer...

What is the Overall Length of the 4-Bike Thule T2 Bike Rack
I checked with Thule and the length of the Thule T2 Platform-Style 4 Bike Carrier # TH916XTR-918XTR from the center of the hitch pin out to the end of the rack is 55 inches. I attached installation instructions for this rack also.
view full answer...

Hitch Pin Hole to Upright Dimension of Rhode Gear Highway 2 Bike Rack # RG8015220
For the Rhode Gear Highway 2 Bike Rack, part # RG8015220, the distance from the hitch pin hole to the upright pole is 11 inches. We offer a few hitch extenders, which you can see by clicking on the link I provided. Keep in mind that using an extension of any kind will lower the tongue weight capacity of your hitch by half. For instance, if your hitch has a 400 lb tongue weight capacity, using the adapter will lower that to 200 lbs. This will mean that the rack and the bikes placed on it can w
view full answer...

What is the Weight of the Kuat NV4 Trailer Hitch Mount Bike Rack
The shipping weight of the Kuat NV4, # N101-103, is 84 pounds. Subtract about 4 or 5 pounds for packing materials and you are looking at about 80 pounds. We do have some reviews on the 2 bike version, # N101, that you should find helpful. The Kuat racks are among the most stylish and functional racks offered by any company and I am sure you will be happy with it. I have included a link to a video review of this bike rack for you to view.
view full answer...

Carrying 4 Bikes on Subaru Outback with OEM Class II Receiver
With a 200 lb tongue weight capacity to work with, you will need to ensure that the weight of the rack used plus the weight of the bikes do not exceed that 200 lb tongue weight capacity. This is not an issue with the bike rack itself, but with the tongue weight capacity of the hitch used on the vehicle. As long as the 200 lb figure is not exceeded, you are free to choose the rack (whether it has a 2,3 or 4 bike capacity) that will work best for your needs. The Apex Swing you mentioned, part #
view full answer...

Overall Length and Distance Between Wheel Trays on the Yakima Holdup 4 Bike Rack
The Yakima Holdup 4 Bike Rack, # Y02433-02435, measures 57 inches from the center of the hitch pin hole to the end of the bike rack. To give you an idea of how far back this bike rack will extend, you can measure 57 inches back from the center of the hitch pin hole on your trailer hitch. The distance between the wheel trays is 11-1/2 inches. I have attached the installation instructions and a demonstration video for you to check out.
view full answer...

Folding Platform Bike Rack Recommendation for a 2007 Honda Odyssey that has Clearance to Fold Up
With the hitch on your 2007 Honda Odyssey you will have a distance of 5 inches from the center of the hitch pin out to the furthest point out on the rear bumper. So you will need a fold up rack that when folded up will have a distance of greater than 5 inches from the center of the hitch pin to the nearest upright bar. There is a rack available that has enough clearance, but the Swagman XTC4 Bike Rack # S64665 only has a distance of 3 inches when folded so it would not work for you. You sh
view full answer...

Can 3 Bikes Be Used on a Class I Hitch if the Weight is Less than the Tongue Weight Rating of Hitch
As long as you do not exceed the tongue weight capacity listed by the hitch manufacturer, the tongue weight capacity listed in the owners manual of your 2010 Infiniti EX35, and never put more than two bikes on the rack you would be fine. The reason you could not put three bikes on this rack even if the total weight was less than the tongue weight capacity is because of the distance of the weight of the third bike away from the hitch opening. The further the weight is away from the hitch the m
view full answer...

Why are Some Bike Racks Rated for Use Behind RVs and Others are Not
The ride at the back of an RV is considerable rougher than at the rear of a passenger vehicle. The reason is because the rear of an RV is extended well beyond the rear axle which acts like a see-saw and creates a lot of movement which puts a lot of stress on the racks. Basically, the difference is like sitting in the front of a school bus compared to sitting at the back of a school bus where it is much rougher. The good new is that we offer bike racks that are rated for use behind an RV. Chec
view full answer...

What is the Maximum Bike Wheelbase for SportRack Trailer Hitch Bike Racks A30901 and A30901LR
The maximum wheelbase for a bike used on the SportRack 2 Bike Hitch Mounted Rack, # A30901, and # A30901LR is 58 inches. The platform rack that will allow for the widest wheelbase is the Swagman XTC-2 extended, # S64650-EXT. When configured properly, this rack can hold a bike with up to a 68 inch wheelbase. I have included some video links for you to view.
view full answer...

Will the Swagman XTC4 and Quad Carry Four Bikes at a Time
Yes, both the Swagman XTC4, # S64665, and the Quad, # S64690, will allow you to carry 1, 2, 3 or 4 bikes at a time. Keep in mind that due to the carrying capacity of these bike racks they will only fit in 2 inch trailer hitch receivers. As long as you have a 2 inch trailer hitch receiver and do not exceed the weight capacity of the bike rack or your trailer hitch, then you will have no problem carrying up to 4 bikes. If you plan on carrying any womens or childrens bikes, then I would recomme
view full answer...

Spare Tire Clearance on 2011 Toyota Rav4 for Bike Rack Clearance
To determine the fit of a particular bike rack, you will need to determine how much clearance will be necessary, and then choose the rack that has a shank long enough to provide that clearance. When the Draw-Tite Class III Hitch, # 75432 is installed on a 2009 Rav4, we found that the distance from the hitch pin hole to the furthest rearward portion of the spare tire was 6-1/2 inches. The 2011 Rav4 and the 2009 model use the same hitch, but any differences in the rear fascia structure between
view full answer...

Why Are Class I Hitches Limited to Carrying Only 2 Bikes on Bike Racks
Your Class I hitch has a 2,000 lb gross weight capacity but only a 200 lb tongue weight capacity. The difference between these two capacities is that gross weight capacity refers to how heavy of a trailer you could tow, whereas the tongue weight capacity refers to how much vertical weight you could put on the hitch. Tongue weight is the relevant capacity when it comes to bike racks because they put a vertical load on the hitch. Another thing you have to consider with bike racks is leverage. A
view full answer...

Will the Yakima DoubleDown 5 Bike Carrier Hold Five 26 Inch Mountain Bikes
Yes, the Yakima DoubleDown 5 Bike Rack, # Y02425, will hold five 26 inch mountain bikes as long as the five bikes do not exceed the weight capacity of the bike rack. This bike rack has a weight capacity of 125 lbs which means each bike will have to weigh 25 lbs or less each. With that many bikes, I would recommend mounting them in alternating directions and if any of them have angled or alternative frames, then I would recommend using an adapter bar like the Yakima Tube Top Adapter Bar, # Y0
view full answer...

What is the Weight and Measurements of the Swagman Platform Style Towing Bike Rack # S64664
The shipping weight on the Swagman towing bike rack, # S64664, is 36 pounds. If you subtract packaging materials, about 5 pounds, then the rack will weigh about 31 pounds. The rack measures approximately 12-1/2 inches from the center of the receiver bar (where it attaches to a ball mount) to the wheel loops. Ball mount # 2736 is one that we often recommend for towing bike racks so you should not have any problems with it. Provided that you stay within the tongue weight capacity of the hitc
view full answer...

Rola Class I Bike Rack with High Tongue Weight Capacity Recommendation for a 2011 Honda Fit Sport
The hitch with the highest weight capacity that will work on the Class I hitch of your 2011 Honda Fit Sport would be the Rola NV2 Hitch Mounted 2 Bike Carrier # 59508. This rack can handle up to 100 lbs and should be adequate for you. I would recommend you put the heavier electric bike on the inside cradles closer to your vehicle. I attached a review video for this rack for you to check out also.
view full answer...

Distance Between Arms and Bike Adapter Bar for a Rhode Gear Trailer Hitch Mount Bike Rack
On the Rhode Gear bike rack, # RG8015220, the distance between the arms, at the cradles, from outside to outside is 13-1/2 inches. This and other important measurement is in the Specs section on the product page to help you determine if it will fit your vehicle and bikes. We have numerous brand of bike adapter bars fro women, childrens, and alternative frame bikes. You can use the Yakima Tube Top, # Y02531, for better ground clearance and to carry the bikes more level. I have included a link
view full answer...

How Many Bicycles Will a Class I Hitch Support on a Mazda 5
Due to the tongue weight capacity of Class I hitches and the tongue weight capacity of the vehicles that require Class I hitches it is recommended to carry no more than 2 bikes. One of the biggest reasons a Class I hitch cannot support more than two bikes is because of the additional stress that is applied by the third and fourth bike. Adding additional weight further from the back of the vehicle is like adding a pipe to the end of a wrench to create more torque. This will damage both the hi
view full answer...

Will a 2012 Kia Sorento Fit in a Garage With The Thule Doubletrack Platform Bike Rack Installed
We had the Thule Doubletrack Platform 2 Bike Rack, # TH990XT, out in our studio so I took some measurements for you. This rack measures 14 inches from the center of the hitch pin hole to the furthest back part of the bike when in the folded up position. The bike rack measures 33 inches from the center of the hitch pin hole to the furthest back part of the bike rack when folded down and the center of the outer bike wheel base measures 31 inches from the center of the hitch pin hole. I have at
view full answer...

Outside to Outside Arm Spacing of the Thule Apex Swing 4 Bike Carrier # TH9027
The outside-outside arm spacing of the Thule Apex Swing 4 Bike Carrier, # TH9027, is 14 inches including the cradles. I did a short video showing this measurement for you, see video link. On the Yakima SwingDaddy, # Y02422, the arms measure 12-1/4 inches apart, outside to outside. Both the Thule Apex and Yakima SwingDaddy racks will have anti-sway cradles for each bike so two cradles on each arm, 4 total, will have the anti sway parts attached to them. You may need to purchase a bike ad
view full answer...

Thule Apex and Vertex Swinging Trailer Hitch Mount Bike Rack Dimensions and Bike Racks for RVs
Only certain bike racks are rated for use behind a trailer but neither of the Thule racks can be used for this application. I have included a link to the bike racks that are rated for this application. The 2 bike racks, # TH9027 and # TH9031, actually have identical measurements. I have included a picture that shows them. The important measurement for a spare tire is going to be the A and B measurements of 10-1/2 inches (10.53). You will need to measure on your vehicle from the center of the
view full answer...

Lower Hinge Measurement on the Thule Vertex Bike Rack for Tailgate Clearance on a Honda Element
I spoke with my contact at Thule and the lower hinge measures 6 inches from the top of the shank. You will want to measure 6 inches up from the top edge in your trailer hitch receiver and check if there is enough clearance for your tailgate on your Honda Element. I have attached a photo of the measurement for you to view.
view full answer...

Bike Weight Capacity for the Swagman Trailhead 2 Bike Carrier
The weight capacity for the Swagman Trailhead 2 Bike Carrier, # S63360, is 35 lbs per bike or a total weight capacity of 70 lbs. Swagman also offers a Locking Anti-Rattle, Threaded Hitch Pin, # S64029, that provides added security while you are away from your bike rack and vehicle.
view full answer...

Compatibility of Swagman Quad Bike Rack # S64690 with 2009 Acura MDX
The Swagman Quad bike rack you referenced, part # S64690 would be a good choice for carrying 4 bikes on your Acura MDX. The rack has a 180 lb weight capacity, which should accommodate your bikes nicely. When loading the bikes on the carrier, be sure to load the heaviest bikes closest to the vehicle. If you have not already decided on a hitch, I would recommend the Curt Class III receiver, part # 13354. This receiver hitch would work well with the Swagman bike rack you mentioned. If you were
view full answer...

Dimensions From Hitch Pin Hole and Ball Mount Hole to Mast on Swagman Trailhead Bike Rack # S63390
On the Swagman Trailhead 4 Bike Carrier, part # S63390, the distance from the hitch pin hole to the upright mast measures 8-1/2 inches. The measurement from the center of the hitch pin hole to where the gusset starts is 9 inches. The measurement from the center of the hitch pin hole to the upright mast is 13 inches. I am including a picture of the hitch with the measurements.
view full answer...

Softride Dura Parallelogram Tilting Trailer Hitch Mount 4 Bike Rack Shank Measurements
the Softride Dura Parallelogram, # SR26247, actually has 2 hitch pin holes in it. I measured them both and the one closes to the end of the shank is 1 inch measuring from the center of the pin hole. The other one is 3-1/2 inches on center to the end of the shank. I included a picture showing these measurements for you. On the Curt multipurpose ball mount, # D210, from the center of the hitch pin hole on the receiver portion to the end of the receiver measures approximately 2 inches. If yo
view full answer...

Can the Arms of the Softride Dura Be Secured to Prevent Theft
I spoke with my contact at Softride and he informed me that in order to prevent theft of the arms and possibly your bikes with this Softride Dura 4 Bike Rack # SR26247 you would need to use the included cable that comes out of the back of the rack and ran it to the yellow loop on the front of the arms of this rack and then secure it with a pad lock of your choice and you would prevent anyone from stealing the arms and your bikes by just removing the arms. For a padlock you could use a Master
view full answer...

Why Class II Hitches Can Not Carry 5 Bikes on a Bike Rack
The reason they recommend 4 bikes as the max with a Class II hitch is that the fifth bike ends up being so far away from the hitch that the increased leverage of the weight of the fifth bike is too much for the hitch. Imagine holding a thirty pound bike, when the bike is held near your body its not too bad. But if you were to hold the bike at arms length it would feel much heavier. That is the same principal with the fifth bike on a Class II hitch, that fifth bike is too much leverage on the
view full answer...

How Much Does the Swagman G2 Trailer Hitch Mount Bike Rack Weigh
The Swagman G2, # S64680, trailer hitch mount platform style bike rack weighs approximately 47 pounds. Light enough for one person but 2 people would make installation or removal much easier. I have included a link to the installation details for you.
view full answer...

What is the Weight Capacity of the Swagman Trailhead 4 Bike Carrier # S63380
The overall weight capacity of the Swagman Trailhead 4 Bike Carrier # S63380, is 100 pounds. You should not exceed the weight capacity of the bike rack by any amount. The Swagman # S63380 will fit 1-1/4 and 2 inch hitches. You will want to check the tongue weight capacity of the hitch and your vehicle as it should not be exceeded. The weight of the bike rack, plus the weight of the bikes will contribute to tongue weight. It is also recommended that you carry the heaviest bikes closest to the
view full answer...

Can a Yakima StickUp Bike Rack Transport a Bike With 29 Inch Tires
The Yakima StickUp 2 Bike Hitch Mounted Folding Rack # Y02420 that you referenced will work on bikes that have tires that are up to 29 inches in diameter. The other capacity to keep in mind is the 90 lb weight capacity of the carrier. I attached a review and installation instructions for this rack for you to check out also.
view full answer...

What is the Height of Yakima DoubleDown 2 Trailer Hitch Mount Bike Rack # Y02423
I went down to our showroom and measured a Yakima DoubleDown Bike Rack, # Y02423. From the bottom of the shank that fits into the receiver to the top of the bike rack measures 43 inches. I have added a picture that shows this dimension. The DoubleDown bike racks only fit on Class II and Class III trailer hitches. I recommend a platform style bike rack because it will be much easier to load bikes on it. The most popular platform bike rack we carry for a Class I trailer hitch is the Swagman XTC
view full answer...

How Tall is the Swagman Trailhead 2 Bike Trailer Hitch Mount Bike Rack, # S63360
The Swagman Trailhead 2 Bike Trailer Hitch Mount Bike Rack, # S63360, measures 36 inches tall from the top of the shank that fits in the receiver to the bottom of the arms. I have made a picture that shows the dimension for you. The ends of the arms are a little higher, approximately 3 inches from the bottom of the arms at the upright post.
view full answer...

How Far Out Does the Thule Hitching Post Pro 4 Bike Trailer Hitch Mount Bike Rack Extend
I spoke with my contact at Thule. She went and measured a Hitching Post Pro 4 Bike Rack, # TH934XTR from the hitch pin hole to the end of the arms. She came up with approximately 38-1/2 inches. The cradles can be slid a little back and forth on the arms. Another important factor is the length of the bikes you put on it so take that into consideration when making calculations. I have included a link to a video for this bike rack.
view full answer...

Why Can a Class I Trailer Hitch Only Handle 2 Bikes on a Trailer Hitch Mount Bike Rack
All Class I hitches should be limited to just 2 bikes on a bike rack designed to fit a Class I trailer hitch. The reason is not the weight capacity of the hitch. It is the amount of torque applied to the hitch. Having more than 2 bikes on a rack puts too much weight too far from the hitch receiver. With more weight further from the hitch and the addition of the bouncing that will occur as you travel, the force will be too much for the trailer hitch to handle and it will damage the hitch, the
view full answer...

What is the Rise on the Thule T2 Platform Style Trailer Hitch Mount Bike Rack
On the Thule T2, # TH916XTR, from the top of the shank that fits in the trailer hitch receiver to the bottom of the wheel cradles where the tires sit measures about 6-1/4 inches. From the top of the shank to the underside of the nearest platform measures 4-3/4 inches. The rack, when folded down, is at a slight angle so the farthest platform will actually be about 3/4 of an inch higher. The 4-3/4 inch rise should keep the rack from contacting the ground. However, on steep inclines and dips
view full answer...

How High Does the Swagman Platform 2 Bike Carrier for 2 inch Ball Mount Raise the Bikes
I went out to the warehouse and pulled the Swagman Platform-Style 2 Bike Carrier # S64664, for 2 inch draw bars and produced a short video showing all of the dimensions you might need to determine if the bike rack will work behind your RV while towing a vehicle. I would recommend contacting your Tow bar manufacturer to see if the added tongue weight of the bike rack and bikes is acceptable with your specific tow bar. The height of the curved shank support bar from the inside top of the ope
view full answer...

What is the Maximum Weight the Softride Versa Bike Rack Can Handle
The maximum weight capacity for this Softride Versa Bike Rack # SR26249 is (2) 50 lb bikes. I attached installation instructions and a review video for this product for you to check out also.
view full answer...

Recommended Two Bike Platform-Style Bike Rack for Hebb Electric Bikes
I cannot recommend using the Swagman XTC-2 for your application, as the weight of your bikes is 43 lbs over the recommended weight capacity. Overloading the rack can lead to damage to the hitch and the vehicle, as well as the loss of the rack and the bikes. The Yakima HoldUp, part # Y02433 offers a 120 lb weight capacity, and would be a much safer alternative. Clicking on the provided link will take you to the assembly and install details for the Yakima HoldUp. For womens bikes or bikes
view full answer...

What Is Distance Between the Support Bars of Highland SportWing Hitch Bike Rack # 1370400
I walked out to the warehouse and put the Highland SportWing Hitch Bike Rack # 1370400, together. The distance between the 2 support bars measured approximately 14-3/4 inches. The Highland SportWing Bike Rack fits 2 inch hitches, can carry up to 4 bikes. You will want to make sure not to exceed the tongue weight capacity of your hitch or vehicle, as stated in the vehicle owners manual. The weight of the bike rack plus the weight of the bikes is considered tongue weight. The Highland SportW
view full answer...

Height in Inches and Length of Bike Arms for the SportRack Escape 4 Bike Rack # A30404TW200
Dimensions for the SportRack Escape 4 Bike Rack, # A30404TW200, are listed in the Specs section on our product page. The bike rack cradles sit about 36 inches above the hitch ball platform and the arms extend out about 26-1/2 inches from the upright bar. This information comes directly from SportRack. I have added dimensions to a photo that should help you determine if this rack will work with your trailer and bikes. I have used this style of rack for my 16 foot Cajun bass boat and 4 bikes nu
view full answer...

What is the Longest Wheelbase Bike that Could Work on a Yakima Holdup 2 Bike Rack # Y02433
I spoke with my contact at Yakima and he informed me that this Yakima Holdup 2 Bike Rack # Y02433 will fit bikes with wheel bases of up to 48 inches. What that means is that the distance between where the tires of the bike touch the ground cannot be larger than 48 inches. Most likely this rack will work on your bike, but you will want to determine the wheelbase of the bike before ordering to be sure. I attached installation instructions for this product for you to check out also. If yo
view full answer...

Can the Thule Apex Trailer Hitch Mount Bike Rack be Used with an Extension, 2007 Infiniti FX-35
I went down to our showroom to take some measurements of the Thule Apex, # TH9027. From the top of the shank that fits into the hitch receiver to the top of the first cradle (where the bottom of the top frame bar on a bike would be) it measures approximately 36 inches. I do not recommend using a hitch extender because it will reduce the tongue weight capacity of the hitch by 50 percent. If you can measure from the center of the hitch pin hole out to the distance required to clear the rear of
view full answer...

Weight Capacity of Rola TX-104 4 Bike Carrier # 59401
The listed weight capacity of the Rola TX-104 4-bike rack, part # 59401, is correct at 100 lbs for 4 bikes. The Yakima hanging hitch 4-bike racks do seem to run at a little higher weight capacity for 4 bikes at 120 lbs, and the Thule hanging hitch 4 bike racks are at 140 lbs weight capacity. I am including links to product pages of the Thule and Yakima 4-bike hanging bike racks. Also, I will include a link to the installation instructions on the Rola bike rack that will list the weight capaci
view full answer...

What Is the Height of Swagman XTC4 # S64665 Above the Hitch Pin With Masts Folded Down
I spoke with my contact at Swagman and she informed me that at the highest point out on the rack, it will be 8 inches above the hitch pin hole when the masts are folded down. You will want to measure the distance from the center of the hitch pin up to see how much clearance you have for your door to open. If there is a distance of greater than 8 inches your door should be able to open with the masts of this Swagman XTC4 Bike Rack # S64665 folded down. Another issue you could potentially run i
view full answer...

Comparison of Thule Parkway # TH957 and Swagman Trailhead # S63380 For Mazda 5
The Swagman Trailhead 4 Bike Carrier # S63380 has a maximum weight capacity of 100 pounds. The Thule Parkway 4 Bike Rack, part # TH957, has a maximum weight capacity of 140 pounds, and each bike cannot weigh more than 35 pounds. Both bike racks can carry 4 bikes, and have a tilting feature to allow access to the rear hatch of your Mazda 5. The main difference is that the Swagman Trailhead will fit both 1-1/4 and 2 inch hitches, but the Thule Parkway will only fit 1-1/4 inch hitches. I w
view full answer...

What Class Trailer Hitch is Required for a 4 Bike Hitch Mount Bike Rack on a 2007 Chevy Impala
In order to use a 4 bike rack and carry 4 bikes, you will need to have at least a Class II trailer hitch on your 2007 Chevy Impala. The good news is that all of the available trailer hitches for your Impala are Class II hitches. I recommend the Draw-Tite Trailer hitch, # 36407. It is the most popular hitch for your Impala. I have included a link to the installation instructions and a video showing a typical installation. With the hitch installed you will be able to safely carry the Thule Hitc
view full answer...

What is the Unpackaged Weight of the Rhode Gear Highway 2 Bike Carrier # RG8015220
I spoke with my contact at Rhode Gear and according the the information they have on this Rhode Gear Highway 2 Bike Carrier it weighs right at 21 lbs. I attached a review video for this product for you to check out also. If you plan on carrying any womens or childrens bikes you may be interested in purchasing a Yakima Tube Top Bike Adapter Bar # Y0253. I attached a review video for this product also.
view full answer...

Width of Wheel Trays on Yakima Holdup 4 Bike Rack
The wheel trays of the Yakima Holdup 4 Bike Rack will accommodate bikes with tires up to 3 inches in width. I spoke with one of my contacts at Yakima, who assured me that a childrens bike with a 38 inch wheelbase would fit with no problems whatsoever.
view full answer...

Bike Rack Recommendation for Carrying 3 Adult Bikes On a 2001 Saturn Ion
You are correct the instructions for the Rola TX-103 3 Bike Carrier, item # 59403, see link, state that the bikes should not exceed 80 lbs. Most adult bikes will weigh in at 25 to 35 pounds so it will depend on the model of the bikes you wish to carry, if the rack would be compatible. We do have 3 bike racks that will accommodate 3 adult bikes up to 100 lbs total, like the Swagman Trailhead 3 Bike Carrier, item # S63365. When using the bike carrier with a Class I trailer hitch, like those ava
view full answer...

Height of Softride Dura Parallelogram # SR26247 With 1-1/4 Inch Trailer Hitch Adapter Installed
On the Softride Dura Parallelogram, # SR26247, there is an 1/8 inch thick plate welded to the top of the 1-1/4 adapter bar. So, from the top of the 1-1/4 inch bar to the top of the 2 inch bar, it would make the bike rack 2-1/8 inches higher when installed in the trailer hitch. From the hitch pin hole on the 1-1/4 inch bar to the face of the 2 inch bar, it measures 3 inches. From the center of the hitch pin hole on the 1-1/4 inch adapter to the center of the nearest hitch pin hole on the 2 inc
view full answer...

Why A Class I Trailer Hitch on a 2011 Toyota Prius Can Only Carry a 2 Bikes on a Bike Rack
The issue with a Class I trailer hitch is not how much the bikes weigh, entirely, it is the amount of torque produced by having weight further from the hitch. With more weight further from the hitch, even if it is a little weight, it can damage the hitch, the rack, and the vehicle, especially when you add in any up and down movement while traveling. You may have heard of or even used a cheater or breaker bar when changing a tire. The longer the bar the easier it is to loosen lug nuts. The for
view full answer...

Distance from Center of Trailer Hitch Pin Hole to Upright Bar on SportRack Bike Rack # A30404XT
I went out to our showroom to measure a SportRack Evader Hitch Mount Bike Rack, # A30404XT. From the center of the hitch pin hole to the back of the upright bar measures 12 inches. To the support bracket where the rack tilts it is 6-1/4 inches. And to the back of the arms it is 10-1/2 inches. I have included a link to a picture I made showing these measurements.
view full answer...

What 4 Bike Hanging Rack Has The Highest Maximum Weight Capacity
You will need to make sure that you are using the SportRack Escape 4 Bike Rack, part # A30404, on a Class II 1-1/4 inch hitch or a Class III 2 inch hitch to be able to have a maximum weight capacity of 180 lbs. It will not work on a Class I 1-1/4 inch hitch. The Class I hitch will not allow the SportRack bike rack to be installed in the hitch because it will have a stopper that will not let the hitch pin holes line up. This is to keep you from overloading a Class I hitch. This SportRack E
view full answer...

Recommend 2 Bike Rack With Short Distance From Trailer Hitch Pin Hole To End of Bike Rack Arms
I walked down to our showroom and measured the Rola TX-102 2 Bike Carrier, part # 59400. If set for a 2 Inch hitch, part # 59400 measures a total of 22-3/4 Inches from the center of the hitch pin hole to the end of the arms. Another rack that I measured was Prorack 2 Bike Carrier, part # PR8062403, which measured 28-3/4 Inches from the center of hitch pin hole to end of the arms. A rack that totals 28 Inches when used with a 2 Inch Receiver would be the Yakima DoubleDown Ace, part # Y02450
view full answer...

Can Highland Sportwing 4 Bike Rack 1370400 Carry a 53lb Downhill Bike with 29in tires
I checked with my contact at Highland, and I confirmed that the carrier would be able to handle a 53lb bike, and the wheel cradles will accept your 3in wide tires. The Aluminum SportWing bike rack # 1370400 has a weight capacity of 160lbs, but the bikes can vary in weight as long as the total load is less than the bike rack capacity. I am including a link to a video review of the SportWing bike rack for reference, if needed.
view full answer...

Using Curt Multipurpose Ball Mount # D210 to Tow a Pop Up Camper and Trailer Hitch Mount Bike Rack
I went out to the warehouse to take some measurements on the Tow Ready 4 Bike Hitch Mounted Folding Rack, # 63124. The distance from the center of the hitch pin hole out to the very end of the rack is 33 inches. To compare, you can measure from the center of the coupler back to the camper. If it is longer than 33 inches, there will be enough clearance. I also measured from the center of the hitch pin hole to the top of the bike rack at the last bike position and it is 38 inches tall. The ligh
view full answer...

Distance from Hitch Pin to Platform on Thule Doubletrack Part # TH990XT
The closest wheel tray of the Thule Doubletrack is approximately 19 inches rearward of the hitch pin hole. To determine how far rearward the closest bike will be of the exhaust, simply measure 19 inches back from the hitch pin hole in your receiver. The Snug Tite receiver lock is included with the Doubletrack. The locking pin will help prevent the rack from moving in the receiver, and it is keyed alike with the locks on the ratcheting arms that hold the bikes to the rack itself. When
view full answer...

Carrying 4 Bikes on A 2010 Honda Accord Using a Class I Hitch and Two Roof Rack Bike Racks
There are only Class I Hitches available for the 2010 Honda Accord. The hitch manufacturers do testing for safety and have found that the 2010 Accord can only safely carry up to 200 pounds of tongue weight. The reason that only two bikes are recommended, on a hitch mounted bike rack, for Class I hitches is that the added torque applied to the hitch and vehicle frame will be too great for the setup, and will eventually if not immediately, cause damage to the hitch or the vehicle frame. Basical
view full answer...

Measurements On The Swagman 3 Bike Carrier Ball Hole Mounted Bike Rack # S64101
I went out to the warehouse and pulled the Swagman 3 Bike Carrier Ball Hole Mounted Bike Rack # S64101. I measured from the center of the ball hole on the bottom plate that mounts to the hitch ball to the upright post, and it measures 2 inches. The upright post is 2 inches in diameter. I also have a diagram of the bike rack that has measurements of the height of the upright pole (33-1/2 inches) and the overall length of the top plate (17-1/2 inches). If you use these measurements and mea
view full answer...

Distance Between Shank and Cradles on Thule Helium Part # TH970XT
On the Thule Helium part # TH970XT the distance from the top of the shank that slides into the receiver to the bottom of the arms that hold the cradles that the bike attaches to is exactly 34 inches. The Helium is truly a quality rack, I am always amazed at how light but strong they are whenever I need to pull one off the shelf.
view full answer...

Will the Kuat NV Aluminum 2 Bike Carrier # N102, Carry a Bike with a 44.7 Inch Wheelbase
Yes, your Giant Suede bike that has a wheelbase of 44.7 inches will fit on this Kuat Aluminum, Hitch Mounted 2 Bike Rack with Wheel Mount Cradles, part # N102. I spoke with my contact at Kuat and he informed me that the # N102 will fit bikes with wheelbases all the way up to 48 inches. However, this rack is for use with 1-1/4 inch hitches, and you have a 2 inch receiver on your 2008 Chevy Silverado. Since you have a 2 inch hitch on your 2008 Silverado you will want to purchase the Kuat Alumin
view full answer...

Trailer Hitch Mount Bike Rack to Accommodate Two 65 Pound Ezip Bikes
I have two bike racks with a 120 lb capacity, the Yakima HoldUp, part # Y02433 or the Thule T2, part # TH916XTR. If the bikes have a battery that could be removed to shed 5 lbs from each bike, you would be in business with either rack. I prefer the locking ratchet hook system on the Thule rack over the cable used by the Yakima model.
view full answer...

What Is The Weight Capacity On The SportRack Hitch Bike Racks, # A30404XT, and # A30403XT
The weight capacity on the SportRack Evader 4 Hitch Bike Rack, # A30404XT, is 180 lbs. for 4 bikes and the weight capacity on the SportRack Evader 3 Hitch Bike Rack, # A30403XT, is 132 lbs. for 3 bikes. Both of these hitches will fit 2 inch hitches and Class II 1-1/4 inch hitches, but if you have a 1-1/4 inch hitch you will need to make sure it is a Class II 1-1/4 inch hitch. These hitch bike racks will not work in a Class I 1-1/4 inch hitch. The Class II 1-1/4 inch hitch has a tongue wei
view full answer...

What is the Weight Capacity of the Thule Helium Aluminum 2 Bike Carrier, # TH970XT
I spoke with my contact at Thule. The weight capacity of the Thule Helium Aluminum 2 Bike Carrier, # TH970 or # TH970XT, is 70 pounds (no one bike can weigh more than 35 pounds). I have included a video of part # TH970XT. You might also be interested in the Alternative Frame Bike Adapter Bar, # TH982XT, for bikes that do not have a top frame bar that is parallel with the ground. I have included a link to a video review of this adapter as well.
view full answer...

How to Measure Hitch Bike Rack Sizes to Determine Which Hitch is Needed
The 1-1/4 and 2 inch sizes you see refer to the hitch receiver opening. If you have the rack, measure the shank at the bottom of the rack. If it measures 2 X 2 inches, then you will need a Class III or higher 2 inch receiver. If it measures 1-1/4 X 1-1/4 inches, you will need to determine whether or not it will fit a Class I or Class II hitch. There are stops welded inside Class I hitches to prevent use of Class II accessories that can overload a Class I hitch. I have added a link below to
view full answer...

Center of Hitch Opening to Back of Upright Bar Distance on Yakima SwingDaddy and Thule Revolver
For both the Yakima SwingDaddy, # Y02422, and the Thule Vertex Swing 4, part # TH9031 the distance from the center of the trailer hitch opening to the back of the upright bar when the carriers are fully extended, is 36 inches. I have included links to video reviews and installation details for both racks below. For the Vertex Swing 4, I would recommend the locking hitch pin, part # THSTL2. For womens bikes or bikes with sharply angled top tubes or step-through frames, using a frame adapter
view full answer...

What is the Rise Height of Swagman XTC4 Bike Rack # S64665 and How Long is the Rack
I spoke with my contact at Swagman. She stated that the Swagman XTC4, # S64665, measures 40 inches long. I went out to the warehouse and assembled one of the XTC4 bike racks. The rack has an 8-1/2 inch rise from the center of the hitch pin hole to the bottom of the end of the rack. I have included a link to the installation details and a video review of this rack below.
view full answer...

Capacities and Dimensions of the Curt and Valley Dual Receiver, Multi-Purpose Drawbars
We have the Curt Multipurpose Ball Mount with 2 inch Receiver for Bike Racks and Cargo Carriers, # D210. This draw bar has a 12-1/2 inch length from the center of the hitch pin hole to the center of the ball hole. It measures 7-1/2 inches from the center of the hitch pin hole to the center of the top receivers hitch pin hole. The ball mount portion has a 2-1/4 inch drop. The receiver has a 6 inch rise. The entire unit rated for 7500 pounds gross trailer weight and 750 pounds tongue weight, but t
view full answer...

How Long Is The Built-In Cable For Locking Bikes On Softride Dura Tilting 4 Bike Rack , # SR26247
The built-in cable on the Softride Dura Parallelogram Tilting 4 Bike Rack, # SR26247, comes out from the rear of the bike rack and across the arms to the front of the rack to attach to the yellow hook. I called the manufacturer (SoftRide) and they said it does not go much further than the yellow hook where it would be locked. They said the length of the cable would be about 36 inches. So it would not give you any extra length to try and wrap it around the wheels and over the frame. I am se
view full answer...

Dimensions of the Softride Dura Parallelogram Rack with 1-1/4 Inch Adapter Installed
The 2 inch portion measures 2 inches square outside dimensions. There is an 1/8 inch thick plate welded to the top of the 1-1/4 adapter bar. So, from the top of the 1-1/4 inch bar to the top of the 2 inch bar, it steps up 2-1/8 inches. From the hitch pin hole on the 1-1/4 inch bar to the face of the 2 inch bar, it measures 3 inches.
view full answer...

Maximum Number of Bikes That Can Be Carried on Rack Used in Class I Receiver on VW Passat
The VW Passat uses a Class I hitch. Due to the limited tongue weight capacity of the Class I, you will indeed be limited to carrying 2 bicycles on the bike rack. Attempting to carry 4 bicycles would unfortunately damage your hitch, and could possibly result in the loss of the bicycles.
view full answer...

What is the Weight Limit for Swagman XTC 2 Wheel Mount Bike Rack
The limit is 35 pounds per bike for a total weight limit of 70 pounds. Bikes can not weigh more than 35 pounds each.
view full answer...

Dimensions of the Anti Rattle Hitch Pin Included with the Swagman XP Folding 3 Bike Rack
The anti rattle hitch pin that comes with the Swagman XP Folding 3 Bike Rack, item # S64950, is 4-1/8 inches overall length and 3-3/4 inches from the bottom of the bolt head to the end of the hitch pin. From the bottom of the bolt head to the start of the groove for the hitch pin clip, that secures the pin, the distance is 3-3/8 inches.
view full answer...

Will a Jeep Tailgate Mounted Swing Away Spare Tire Clear The SportRack Super EZ 2 Bike Carrier
The distance from the center of the 1-1/4 inch Class II receiver hitch pin hole to the highest point on the SportRack Super EZ Platform-Style 2 Bike Carrier, item # A30901LR, when the upright bar is folded, is 11 inches. As long as the distance from the center of the receiver hitch pin hole on your Jeep to the bottom of the spare tire is 11 inches or greater this bike rack will work and the spare will be able to swing out.
view full answer...

What is the Height of the Upright Tube on Tow Ready 4 Bike Hitch Rack
The Tow Ready 4 Bike Rack measures right at 33 inches from the top of the shank to where the main tube makes the turn. It is not a 90 degree bed, so at the end of the arm, it would be more than 33 inches.
view full answer...

What is the Weight Capacity of the Swagman XTC4 Wheel Mount Bike Rack S64665
I spoke with my contact at Swagman and the weight limit is 35 pounds per bike. The wheel hoops are not designed to hold bikes more than 35 pounds.
view full answer...

Weight Capacity of Thule Parkway Part # TH958
According to our contacts at Thule, the Thule Parkway 2 Bike Rack, part # TH958 has a 70 lb weight capacity. The Yakima DoubleDown, part # Y02423 has a 90 lb capacity that would easily carry your bikes. The DoubleDown features upgraded anti-sway cradles that prevent the bikes from swaying back and forth during travel. Last but not least, the DoubleDown features an integrated bottle opener for that after-ride refreshment.
view full answer...

What Does Carrier Weight Mean On The Yakima Hitch Bike Racks, # Y02420, Will It Fit 1-1/4 Inch Hitch
The 42 lbs. carrier weight on the Yakima Hitch Bike Racks, # Y02420, is what the bike rack weighs. So the maximum weight capacity on the Yakima Bike Rack is 90 lbs., and if you add the carrier weight (42 lbs.) it will be 132 lbs. of total weight being put on the tongue of your hitch. The Yakima bike rack will work on a 1-1/4 inch hitch but it does have to be a Class II hitch. Many hitch accessories are designed for Class II hitches, which are rated for 300 lbs to 350 lbs. tongue weight to pre
view full answer...

Distance Between the Arms on the SportRack Escape 4 Bike Hitch Mounted Folding Towing Bike Rack
The SportRack Escape 4 Bike Hitch Mounted Folding Towing Rack, # A30404TW200, measures 11-3/4 inches between the two arms and 14-1/2 inches from the outside of one arm to the outside of the other arm. So the distance from the center of one arm to the center of the other arm is 13-1/8 inches. If you need a towing 4 bike rack that will accommodate a childrens bike with a 10 to 12 inch frame opening, I recommend a single arm rack. We have several in this category. I have included a link to them
view full answer...

Distance from Center of Hitch Pin Hole to Nearest Wheel Cradle on SportRack Bike Rack #A30901LR
I spoke with my contact at SportRack and she told me that the distance from the center of the hitch pin hole to the first wheel cradle is 12 inches on the SportRack Super EZ Platform-Style 2 Bike Carrier, # A30901LR. The distance from the center of the hitch pin hole to the nearest part of the rack (the bracket where the support arm pivots) is 9 inches.
view full answer...

Which Platform Style Bike Racks for 1-1/4 Inch Hitches Have the Highest Weight Capacity
The 4 platform bike racks we have for 1-1/4 inch hitches with the highest weight capacities are as follows. The Thule T2 # TH917XTR with 100 pounds, Kuat NV # N102 with 110 pounds and the Kuat Core # N104, each with a 120 pound capacity. The Kuat Core will only fit Class II 1-1/4 inch hitches and the Kuat NV and Thule with fit both Class I and II 1-1/4 inch hitches. If you are unsure which class hitch you have, the Kuat NV, part # N102 will fit both and give you 110 pounds of bike carrying
view full answer...

How Much Do the Yakima DoubleDown 4 and DoubleDown 2 Bike Racks Weigh
Some racks can be quite heavy! The 4 bike Yakima racks vary depending on the model. The BigHorn weighs about 30 pounds. The SwingDaddy weighs about 54 pounds. The DoubleDown 4 weighs 41 pounds. The FlipSide 4 weighs 35 pounds. The 2 bike rack from the video, the Yakima DoubleDown 2, # Y02423, weighs in at 36 pounds. This rack will fit in 1-1/4 (Class II only) or 2 inch receivers. I have included a link to the installation details for this rack below. Our lightest 2 bike rack is th
view full answer...

Does the Tongue Weight Rating for Bike Rack A30404TW200 Include the Weight of the Bikes
Yes, the weight of the bike rack and the weight of your bikes would count toward the tongue weight. If you would need more tongue weight capacity for your particular application, you might try a dual-purpose ballmount like part # D210, and simply use the non-towing version of the same bike rack, part # A30404. The weight of bike rack and bikes would still count toward the tongue weight, but the # D210 adapter has a higher tongue weight rating of 350 pounds. You would still need to
view full answer...

Will Thule Doubletrack Bike Rack TH990XT Have Enough Clearance on a 2009 Pontiac Vibe
The Thule Doubletrack bike rack # TH990XT would have a clearance of 7-1/2 inches from the hitch pin hole to the folding bracket, where the bike would stand upright in the folded position. You should have plenty of room to use the bike rack on your 2009 Pontiac Vibe, as long you have measured from your hitch pin hole to a point past your bumper and any other items that might interfere with the bike rack installation. The distance from the hitch pin hole to the upright bar on the bike rack
view full answer...

What is the Capacity of the SportRack 2 Bike Rack for 1 and 2 Bikes on a 1999 Honda CR-V
I spoke with my contact at Thule, the manufacturer, about the capacity of the SportRack Super EZ Platform-Style 2 Bike Carrier, # A30901LR. They told me that the capacity with two bikes is 90 pounds. With one bike, the capacity is 45 pounds. Fully loaded and at capacity, this will put a total of 145 pounds on your tongue weight. Even with a Class I, 1-1/4 inch hitch, there would still be 55 pounds of capacity left over.
view full answer...

Total Length of SportRack Escape 4 Bike Rack, Part # A30404
The total length of the SportRack Escape 4 Bike rack is 40-1/2 inches. This length represents the distance from the end of the shank measured across to the far end of the arms that the bikes are suspended from.
view full answer...

Order Tracking
Shipping Information
Contact Us
About Us

Help Videos and Articles
Search
Privacy Policy
Your Account Login