Air Intake Filter Specs:
Features:
Improve the performance of your engine with this heavy duty, custom fit engine air filter. Replaces your existing filter to help protect your engine from contaminants and improve air flow. Embossed pleats trap dirt, debris, and other particles.
Installation Notes:
Product is considered a Heavy Duty filter
More Information >Air Intake Filter Specs:
Features:
Improve the performance of your engine with this heavy duty, custom fit engine air filter. Replaces your existing filter to help protect your engine from contaminants and improve air flow. Embossed pleats trap dirt, debris, and other particles.
Installation Notes:
Product is considered a Heavy Duty filter
More Information >Air Intake Filter Specs:
Features:
Improve the performance of your engine with this heavy duty, custom fit engine air filter. Replaces your existing filter to help protect your engine from contaminants and improve air flow. Embossed pleats trap dirt, debris, and other particles.
Installation Notes:
Product is considered a Heavy Duty filter
More Information >Air Intake Filter Specs:
Features:
Improve the performance of your engine with this heavy duty, custom fit engine air filter. Replaces your existing filter to help protect your engine from contaminants and improve air flow. Embossed pleats trap dirt, debris, and other particles.
Installation Notes:
Product is considered a Heavy Duty filter
More Information >Videos
for Air Intake Filter
Help Articles
for Air Intake Filter
Expert Answers
for Air Intake Filter
The part #LC293054 does come with two bags which is correct for a tandem axle trailer. I am not sure why it's listed as for a single axle but I will have that changed.
view full answer...Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…
view full answer...The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.
view full answer...Are you looking at the Blue Ox SwayPro weight distribution shanks, like part #BXW4002? If so, Blue Ox does not give these shanks a specific class rating. All of their shanks fit 2 inch trailer hitches and have a maximum towing capacity of 15,000…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...Yes, you can use the Bulldog Powered Drive Trailer Jack #BD500199 in place of your existing jack because the mounting hole pattern in the bracket will be the same between the 2 jacks. Provided that your existing jack also has a round outer tube…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...The distinction you're referring to is about whether or not your Silverado has running boards or steps that sit under the bed and could block the fitment of a frame mounted camper tie-down. The hitch stipulation is in place because some…
view full answer...Yes, the Universal Installation Kit for Trailer Brake Controller item #ETBC7 does fit the 2021 Ram ProMaster 1500 so long as you have a 4-way wiring harness installed like the Curt T-Connector Vehicle Wiring Harness item #C58DR. The item #ETBC7 kit…
view full answer...For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…
view full answer...There is indeed a trailer hitch receiver that fits your 2024 Subaru Crosstrek Wilderness, from Curt, with the correct part number being the following: - Curt Trailer Hitch Receiver #C13382 I verified this fit with the manufacturer for you, and it…
view full answer...Erickson has the spacing for the mounting holes of the #EM09160 before and after the chock at approximately 4-3/8" center to center. Since they unfortunately do not offer a custom backing plate the #e96RR you purchased is going to be the…
view full answer...Filter Products (8)
Contact and Help
What our customers are saying:
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Randy
Watkinsville, GA