Ultra-Fab Electric A-Frame Jack - 18" Lift - 3,000 lbs

Ultra-Fab Products Trailer Jack - UF38-944017

Easy-to-use jack has 12V motor for quick, simple lifting. Corrosion-resistant, die-cast aluminum cap and hardened steel gears make for a long-lasting jack. Dual side lights help you to set up camp at night.

Features:

• Tongue jack positions quickly and easily
• 12V Motor powers jack, eliminating need for hand cranking
  • Built-in, water-resistant toggle switch for easy operation
  • Integrated circuit breaker prevents motor damage
  • All-steel gears are strong and durable
• Dual side lights make it simple to set up your camper at night
• Emergency, ratchet-style crank socket
  • 9/16" Deep well socket inserts into end of drive collar - ratchet clockwise to retract, counterclockwise to extend
• Easy bolt-on or weld-on installation for A-frame trailers
  • Hardware not included
  • Mounting holes fit 2" or 2-1/4" spacing
• Round, removable footplate included
• Die-cast aluminum cap resists corrosion
• Sturdy steel construction with black powder coat finish

Specs:

• Bracket height:
  • 25-1/2" Retracted
  • 43-1/2" Extended
• Lift: 18"
• Lift capacity: 3,000 lbs
• Outer tube diameter: 2"
• Inner tube diameter: 1-3/4"
• Footplate diameter: 5-1/2"
• 1-Year warranty

38-944017 UltraFab Tongue Jack - 4,000 lbs

Customers compare UF38-944017 to these similar products

Electric A-Frame Tongue Jack - 18" Lift - 3,500 lbs$222.95

Ultra-Fab Electric A-Frame Jack - Drop Leg - 18" Lift - 3,500 lbs - 2" O.D.$229.95

Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs$164.95

Pro Series Powered A-Frame Jack - Fixed Leg - 18" Lift - 2,500 lbs$159.95

Bulldog Powered-Drive Trailer Jack - Drop Leg - A-Frame - 17" Lift - 4,000 lbs$279.95

Customers Who Purchased This Trailer Jack Also Bought...

Ultra-Fab Protective Cover for Electric A-Frame Jacks - Vinyl $9.99

E-Track Tie-Off Ring, 4K $4.59

American Flag 2" Trailer Hitch Receiver Cover $14.95

In-Line Circuit Breaker - 20 Amp - Perpendicular Mount Bracket $3.49

Dexstar Steel Spoke Trailer Wheel - 16" x 6" Rim - 6 on 5-1/2 - White Powder Coat $48.95

Ask the Experts about this Ultra-Fab Products Trailer Jack

• Connecting a Power Lead From an Electric A-Frame Jack to Trailer Accessory Battery
  
• If you are using an internally grounded electric jack like the Ultra-Fab Electric A-Frame Jack, part # UF38-944017, you simply run the power lead to the accessory battery on the trailer and connect it to the positive terminal using something like a ring terminal, like part # DW05705-1. You will also want to make sure the negative post of the battery is grounded to the trailer frame so the circuit is complete. This type of jack will only require the power lead wire to be connected as it is gro
  view full answer...


• Where Does the In Line Fuse Holder Get Installed on Ultra-Fab Electric A-Frame Trailer Jack
  
• On the Ultra-Fab trailer jack # UF38-944017 the in line fuse holder will be cut in half and spliced in along the power wire. Ultra-Fab makes the following statement: The Fuse Holder can be installed by means of either crimping or soldering the connections. For convenience the Fuse Holder should be installed near the power source. Cut red wire in half, connect one end to the end of the black wire from the jack and connect the other end of the red wire to the positive post of the battery.
  view full answer...


• How to Grease the Ultra-Fab Electric A-Frame Jack # UF38-944017
  
• Base on the installation instructions, to grease the jackscrew on the Ultra-Fab Electric A-Frame Jack, # UF38-944017, extend the jack until the grease fitting is aligned with the hole in the outer tube. You can apply enough grease with two pumps from a standard grease gun. To grease the gears, you will need to first remove the fuse from the fuse holder. Next, remove the gear cover via 4 phillips screws to expose the gears. Then, grease the gears using chassis lube and reinstall the cover. Th
  view full answer...