Select Your Vehicle
view cartView Cart

CALL NOW - 800-298-8924

Product Experts Available Now!

Free Shipping on Orders Over $99

Only 7 Hours 49 Minutes Remaining



Trailer Jack > Landing Gear > Powered Jack > Weld-On > 37 Inch Lift > With Foot > 6000 lbs > Stromberg Carlson


Stromberg Carlson Electric Landing Gear Set - Weld On - 21" Lift - 6,000 lbs

Stromberg Carlson Trailer Jack

ratingratingratingratingrating (3 reviews)


Code:   LG-1

Retail:$514.95

Price:$424.95


Shipping Special

Shipping Weight: 74 pounds

Quantity: 







Stromberg Carlson Trailer Jack - LG-1

Sweat no more with this electric, fifth-wheel landing gear that can be used easily by even the least experienced camper. The landing gear can support up to 6,000 lbs, and the IP-rated switch provides safe operation. Drop legs adjust up to 16".

Features:

  • Perfect for 5th-wheel campers
  • Electric-powered adjustment for easy operation
  • Single-speed Lippert motor has built-in safety features
    • Motor won't trip circuits or cause problems with coach's electrical systems
    • IP-rated switch will not spark, so it can be mounted safely in bottle-gas area
  • Drop legs minimize jacking time and help to level the trailer on uneven ground
    • Legs adjust in 1" increments
    • Cage pins included to release drop legs
      • Upgrade to spring-loaded pull pins (LG-119113; sold separately) for simpler drop-leg release
  • Hand crank included for manual operation
  • Heavy-duty steel construction
  • Gear box housed in a corrosion-resistant aluminum body
  • Landing gear welds onto trailer frame
  • Set includes 2 jacks, gearbox, motor, switch, footplates, cross shaft, hand crank and hardware


Specs:

  • Lift: 21" from weld-on point
  • Drop-leg travel: 16"
  • Combined weight capacity: 6,000 lbs
  • Cross shaft length: 41" - 71"
  • Footpad dimensions: 8" long x 5" wide x 2" tall
  • Black tube dimensions: 2-1/2" x 2-1/2"
  • 1-Year warranty


Note: Landing gear is designed to stabilize a portion of your trailer's weight, not to support the full GVWR of your trailer. Do not use landing gear to lift your trailer or RV during tire changes or service work because doing so will exceed the capacity of the landing legs.


Unlike some landing gear, Stromberg Carlson's was designed with safety in mind. The motor, manufactured by Lippert, won't trip circuits or cause problems with the coach's electrical systems. In addition, the IP-rated switch will not spark, so it can be mounted safely in the bottle-gas area.


Convenience is also a hallmark of this product. An inner drop leg on each jack makes leveling easy by allowing the jack feet to reach the ground quickly and at varying heights, saving time and thus reducing the draw on the trailer's battery. The cage pins that secure the drop legs can be replaced with spring-loaded pull pins (LG-119113; sold separately) that allow for single-handed operation. Large, rectangular, pivoting footpads are included, but you can use larger, 9-inch-diameter pads (LG-210475; sold separately) instead if you often camp on soft ground.


This system and its parts were designed to be compatible with most of the other fifth-wheel landing gear on the market, including Atwood and Lippert. If you're replacing your old landing gear, you can install this set from Stromberg Carlson using your existing mounting hardware.



LG-1 Stromberg Carlson Deluxe Electric Landing Gear for Fifth Wheel










Customer Reviews

Stromberg Carlson Electric Landing Gear Set - Weld On - 21" Lift - 6,000 lbs - LG-1

Average Customer Rating:  ratingratingratingratingrating4.3 out of 5 stars   (3 Customer Reviews)

Sweat no more with this electric, fifth-wheel landing gear that can be used easily by even the least experienced camper. The landing gear can support up to 6,000 lbs, and the IP-rated switch provides safe operation. Drop legs adjust up to 16".


- LG-1

ratingratingratingratingrating by: Ken M09/18/2014


First of all I want to say that any of the following comments by me is NOT a reflection on etrailer.com whose support and product shipping has been excellent. It is more as a informational thing than anything. I installed this unit on my 2007 28' Thor Transport toy hauler after it fell off the jacks and destroyed the landing gear (that just made me so happy, you just don't know the joy..). My first comments are for Thor, I want to thank them for the absolute cluster (you know what) of an install of the original gear. Totally inaccessible and the worst engineered and assembled garbage ever. The original gear was tack welded at the stops and the carriage bolts for the mounting brackets were installed so that you could not remove them, they all needed to be cut off, a real dream job in an inaccessible location. In addition, I had to remove the 5500 onan generator and the (2) 7.5 gallon propane tanks and the sheet metal enclosures and doors. Next I would like to thank Lippert and Stromberg Carlson for continuing their questionable design of these legs which are only supported by one tab (on the legs) and one bracket on each leg in the load bearing direction (the other tab supports the leg when in the non-load bearing position. And for the 2 extra bolts (1/4-20 x 1 1/2" with jam nuts) that no one seems to know where they go. Also, there is a lot to be desired with the instructions, but that's just me I guess. Be sure to accurately measure your existing brackets prior to getting started because this could be a game changer if they are off by more than a 1/4" or more, you would have to have your brackets cut off and re-welded. As for my Thor, they were off by about 1/8" and I was able to grind off the bottom of the lower tab (on the leg) to make them fit into my existing brackets. After completing the job (3 days in 105 degrees) I still have some questions about the carriage bolts that were shipped, if I were to do it again I would change the bolts to a much stronger bolt, but it's to late for me now. Etrailer had the best price and fastest shipping and were very helpful, would I buy again from them, you bet... 151953






- LG-1

ratingratingratingratingrating by: Jim C.04/11/2014


I found the product was of good to excellent quality. However when reviewing the installation directions it had no directions on how to wire the elec. motor to the control switch. I found the wiring instructions on the motor manufacturing web site. I would recommend that these instructions be with the installation instructions. Also when connecting the left & right landing gear together with the provided 1" square tube the bars were not long enough to make the span on a standard 5th wheel camper. I had to use my existing bar. I would use etrailer.com again and I hope this helps them make corrections to this package. 124726






- LG-1

ratingratingratingratingrating by: Jim Pressley02/08/2013


Great, easy install 65527




3
3


Ask the Experts about this Stromberg Carlson Trailer Jack
Expert Answers about Stromberg Carlson Electric Landing Gear Set - Weld On - 21" Lift - 6,000 lbs - LG-1Do you have a question about this Trailer Jack?


  • Availability of Replacement Lead Jack and Parts for Stromberg Carlson 5th Wheel Landing Gear # LG-1
  • The jack with the motor is referred to as the lead jack, while the other jack is called the follower. Since the jack on the motor side is in need of replacement, you would need the lead jack. The lead jack is not terribly difficult to replace. You would need to disconnect the drive rod that connects the two legs, remove the lead jack, install the replacement lead jack, and pull the motor and gearbox off the defective jack and install on the replacement. If you were using the Stromberg...
    view full answer...

  • Is the Stromberg Carlson # LG-179013 the Same as the Lippert Universal Fit Lead Jack # 179013
  • I spoke with my contact at Stromberg Carlson and the Replacement Lead Jack with Drop Leg, # LG-179013, is the same part as the Lippert Universal Fit Lead Landing Gear, # 179013. The only difference between the two products is that they are sold through different companies so the part numbers are slightly altered. If you were interested in a replacement follow jack with drop leg you can took at part # LG-179014 or the entire assembly is available with part # LG-1.
    view full answer...

  • Stromberg-Carlson Replacement Follow Jack for 5th Wheel Landing Gear Models LG-1 and LG-183708
  • The Stromberg-Carlson Replacement Follow Jack for 5th Wheel Landing Gear, part # LG-179014, is a replacement for the non-driven sides of the LG-1 powered landing gear and LG-183708 manual landing gear. Both of these landing gear products use weld-on installation and both have a 6000-lb weight rating. According to my research on the Forest River website, the Cardinal 35-foot 5th wheel trailer model 3030RS has a dry tongue weight of 2,550 lbs. A set of landing gear rated for 6000 lbs will...
    view full answer...

  • What Landing Gear Will Fit 1996 Avion 5th Wheel Trailer
  • I have a solution for your 1996 Avion 5th wheel, however, it is not as simple as getting two new legs. Your Avion was manufacturered by Fleetwood and the landing gear was manufacturered by RBW. Fleetwood discontinued the Avion and RBW sold out to Al-Ko. Al-Ko decided to discontinue the landing gear and sold the rights to Atwood Mobile. Atwood Mobile decided to not produce the original RBW landing gear. however, to make a long story short, after my research I have found a way for you...
    view full answer...

  • Locating Replacement Gears for Landing Gear Legs on a 2000 Cameo 5th Wheel Trailer
  • I have some information that may help, however, replacement gears for the landing gear legs on your 2000 Cameo fifth wheel trailer may be difficult to find. Typically, landing gear manufacturers do not stamp their name or part number on their landing gear legs. Since most landing gear manufacturers do not make their parts interchangeable between one another, the only way to locate the correct replacement gears is by knowing the manufacturer and part number of the landing gear which involves...
    view full answer...

  • Stromberg Carlson Landing Gear # LG-1 for Jayco Qwest Fifth Wheel Camper
  • The Stromberg Carlson # LG-1 is an industry-standard landing gear that should fit on your fifth wheel with no problems. The mounting brackets weld directly to the frame of your fifth wheel, and the jacks would then mount into the brackets. As long as your Jayco Qwest has exposed frame members under the trailer loft for the brackets to weld to, the LG-1 will work great for you. I have linked you to a copy of our return policy.
    view full answer...

  • Will Stromberg Carlson Replacement Follow Jack # LG-179014 Fit On Fleetwood Prower Lynx Camper
  • After consulting with Stromberg Carlson, I have found that the Stromberg Carlson Replacement Follow Jack # LG-179014 is a compatible replacement for the follow leg on your Fleetwood Prower Lynx 5th-Wheel camper. This item replaces the follow jack for your tandem landing gear. It is the jack in the landing gear that does not have a crank or motor mounted to it. It works with most brands of landing gear and is constructed of heavy-duty steel. It has a lift of 21 inches from the weld-on...
    view full answer...

  • Is the Lead Jack for the Stromberg Carlson Electric Landing Gear Set Available Separately
  • We do sell the Stromberg Carlson Lead Jack with Drop Leg, # LG-179013, however, it does not come complete with the gear box or the motor. The replacement gear box, # LG-179015, is available separately as well as the motor and switch kit, # LG-217884. You could purchase the entire Stromberg Carlson Electric Landing Gear Set together with part # LG-1. I have attached links to all of the parts that I have referenced.
    view full answer...

  • How Landing Gear Jacks are Connected to Fifth Wheel
  • The outer tube of the landing gear is attached to the fifth wheel frame via some frame clamps. The clamps themselves are usually welded to the trailer frame, and bolted clamps hold the outer jack tube in place. The inner tube of the jack will extend and retract, raising and lowering the front of the fifth wheel. The diagram I provided might make it a bit more clear for you.
    view full answer...

  • Stromberg Carlson Electric Landing Gear Motor Just Spins and Does Not Raise/Lower Jack Leg
  • It sounds like the motor is not engaging the gears and/or screw inside the leg on your landing gear. There is a screw and fixed nut inside most jacks. A handle or motor turns the gears that turn the screw to raise or lower the jack leg. There could be a roll pin in the shaft of the motor that engages the gears that is missing but you would have to take apart the jack to find it. The good news is both the gearbox, # LG-179015, and motor, # LG-142178, are available. We also have a repair...
    view full answer...

  • Availability of Replacement Motor for Lippert Model 1300 Power Tongue Jack
  • The part you referenced, Stromberg-Carlson Motor and Switch Kit for Landing Gear # LG-217884, is for converting Stromberg-Carlson manual landing gear to powered, or to replace the motor and switch on their # LG-1 electric landing gear. It is not suitable as a replacement motor for a tongue jack. My contact at Lippert advises that they do not offer a replacement motor for their powered tongue jacks. These units are not user-serviceable except for exterior components such as power switches...
    view full answer...

  • What Type of Grease is Used on the Stromberg Carlson Electric Landing Gear Set # LG-1
  • According to my contact at Stromberg Carlson, the Electric Landing Gear Set, # LG-1, uses white lithium grease for the gears and drive screw. If you are looking for grease to use on your current set, I recommend using our LubriMatic White Lithium Grease, # L11350.
    view full answer...

  • Troubleshooting A Stromberg Carlson Landing Gear Motor that Shuts Off After Only a Few Seconds
  • The motor that is on the Stromberg Carlson Electric Landing Gear Set # LG-1 draws 30 amps. It sounds like either you have a weak ground or you are overdrawing the current wiring you are using to power the motor. You might check the wiring of both the power and ground wires you are using for the motor because it sounds like the problem lies somewhere in there. You could try running a jumper cable from the positive side of the battery of your vehicle to the jack and the same for the ground...
    view full answer...

  • Compatibility of Stromberg Carlson # LG1 Landing Gear with Lippert Fifth Wheel Frame
  • The # LG-1 Landing Gear you referenced is actually manufactured by Lippert Components and offered to the aftermarket by Stromberg Carlson. It would be fully compatible with your Lippert frame and should fit perfectly in the existing brackets, according to my contact at Stromberg Carlson.
    view full answer...

  • Would Replacement Motor Eliminate Noise In Atwood Landing Gear On 2005 Travel Supreme Trailer
  • If you have replaced the pin and the gear box on your landing gear, it seems there are only a couple of components you have not addressed. Unfortunately, we would not be able to say for certain that replacing the motor would take care of the clicking sound you are hearing. Are you sure the sound is coming from the main gear or could it be coming from the follower? Or could it possibly be coming from the screw that is inside the landing gear leg itself as it raises or lowers? Without seeing...
    view full answer...

  • Stromberg Carlson Electric Landing Gear Jack Recommendation for a 2003 Cherokee 295L 5th Wheel
  • I think I have a better solution for you. I think the Stromberg Carlson Electric Landing Gear Set part # LG-1 would be a better match for your 2003 Cherokee 295L 5th Wheel trailer. If you check out this jack you will see that the amount of jack and motor that is above the top mounting bracket is considerably less than the # BD500161 that you referenced so it should work well for you as long as its 6,000 lb capacity would be adequate.
    view full answer...

  • Attaching Stromberg Carlson Landing Gear Set, # LG-1 To 2003 Cherokee 295L Fifth Wheel Trailer
  • Most landing gear sets like the Stromberg Carlson Electric Landing Gear Set, part # LG-1 you referenced, should fit where your old landing gear legs were attached. You can verify this by measuring the distance between the mounting clamps that are welded to the trailer frame. You should have 17-1/2 inches from the bottom of the top frame clamp to the top of the bottom frame clamp. This has a 21 inch lift and a capacity of 6,000 lbs. I have attached a drawing that gives you an idea where...
    view full answer...

  • What Landing Gear Does the Lead Jack Repair Kit for Stromberg Carlson Landing Gear # LG-146059 Fit
  • Your question came in totally blank, but in case you are wondering what the Lead Jack Repair Kit for Stromberg Carlson Landing Gear # LG-146059 you referenced fits it is designed to fit Lippert Components Venture LG-1 or LG-183708 landing gear.
    view full answer...

  • Electric Landing Gear Recommendations for a 2002 2454 Sportsmen Fifth Wheel
  • If you have Atwood Landing Gear part # 75333 on your trailer then you could use the Electric Motor for R.V. Landing Gear # 75391 that you referenced to add an electric motor. If you are looking to replace your current landing gear with a set that has a motor and you don't need more than 6,000 lbs of lifting capacity you could get the Stromberg Carlson Electric Landing Gear Set # LG-1. If you need more capacity I would recommend the Ultra-Fab Deluxe Electric Landing Gear Set # UF17-943010....
    view full answer...

  • Replacement Scissor Jack Handle for a 2007 Gulf Stream Amerilite Travel Trailer
  • Your Gulf Stream trailer could have any number of brands of scissor jacks on it so I would need to know the brand of the jack or the size of the bolt the handle fits on to determine the proper size handle if available. Handle # JCH-1 is for scissor jacks that have a 3/4 inch bolt. The same goes for handle # BAL-24033 for BAL scissor jacks. This is likely the size you need. The handle you purchased, # LG-119226, is for landing gear, # LG-1, but not scissor jacks.
    view full answer...

  • Replacement Landing Gear for 2002 Carriage Cameo F34CK3 5th Wheel Trailer
  • The Stromberg Carlson Electric Landing Gear Set you referenced, part # LG-1, includes weld-on brackets for installation on your 5th wheel's frame. You would not need to re-use the brackets from your existing landing gear. This powered system has a cross shaft length of 41 - 71-inches, 21-inches of lift and a 6000-lb weight capacity.
    view full answer...

  • Landing Gear on 1996 Prowler 5th Wheel Cannot Take Weight of Trailer
  • If the motor and gear box on your Prowler's landing gear appear to be working properly but the jacks do not withstand the weight of the trailer, then it is likely that the main threaded screw that drives the inner portion of the leg is stripped. This part is not offered on its own. If you have Stromberg-Carlson, Atwood or Lippert 3000-lb-rated landing gear you can replace the lead and follow legs and re-install your motor and cross-shaft using parts # LG-179013 and # LG-179014.
    view full answer...

  • Repair Kit for Lippert Components Venture Landing Gear Lead Leg
  • We do offer a lead leg repair kit for the Lippert Components Venture landing gear models # LG-1 and # LG-183708 and that repair kit's part number is # LG-146059. You can view this item's contents and the selling price by clicking on the link provided.
    view full answer...

  • What Does the Replacement Stromberg-Carlson Crank Handle Fit
  • Replacement crank handle # LG-119226 is only listed as a fit for Stromberg-Carlson landing gear # LG-1 or # LG-183708. It will also work with Venture, Atwood and Lippert landing gear. I cannot confirm if it will fit any other jacks. The landing gear models are for both lifting and stabilizing a trailer (usually a 5th wheel or gooseneck trailer). If you need a replacement handle for your jack let me know what jack or jacks you have and I can determine if we have anything that will fit.
    view full answer...

  • Height of Outer Tube on Stromberg-Carlson Landing Gear # LG-1
  • I spoke with my contact at Stromberg-Carlson and found out that the height of the outer tube for landing gear set # LG-1 is 29-1/2 inches.
    view full answer...

  • Landing Gear that Stop Retracting after Weight is Off the Jacks
  • That is a bizarre problem, so the jack will retract and lower your trailer up until the weight of the trailer is no longer on the jack and then it stops? Does it stop as soon as the jack legs starts to lift off the ground? Or does it stop before all of the weight of the trailer is off of the jack leg? Is it possible that the jack has topped out and can no longer lower any further? If the jack uses a drop leg you might be using too low of a setting. Try raising the inner leg in the outer...
    view full answer...

  • Replacement Landing Gear Follower Leg for a 2010 Montana 5th Wheel Trailer
  • The Stromberg Carlson replacement follower leg, # LG-179014, is designed as a replacement for landing gear # LG-1 and # LG-183708. But also works with most other brands including Atwood, Lippert, and Venture. It is very likely this leg will work with your landing gear.
    view full answer...

  • Replacement Landing Gear Jack Recommendation
  • The pictures you submitted didn't make it through. Because I don't know what landing gear set you have on your trailer it would be pretty hard for me to recommend replacement parts. I did attach a link to a page that has all of the replacement landing gear motors we offer. If your landing gear is an Ultra-Fab, Stromberg-Carlson, or a Lipper LCI chances are we have a replacement motor.
    view full answer...

  • Landing Gear Motor that Looks Like Stromberg Carlson Only Travels One Direction
  • If you had the Stromberg Carlson Landing Gear part # LG-1 the correct switch would be the part # LG-145236. This would wire in pretty easily and would be self-explanatory once you got into the install. For a motor and a switch you would want the part # LG-217884. If you can operate the jack manually up and down but not with the switch then the problem is either the switch or the motor. Most likely the switch. If you don't have the # LG-1 and can't determine what brand gear you...
    view full answer...

  • Will Replacement Follow Jack # LG-179014 Work on a 2008 Dutchman Denali Landing Gear
  • The Replacement Follow Jack with Drop Leg, # LG-179014, is designed for use with the Stromberg Carlson # LG-1 or # LG-183708 landing gear and also works with most other brands of landing gear, including Atwood and Lippert. This jack measures 2-1/2 inches wide and has a weight capacity of 3,000 pounds. If you would like to send me an email with the manufacturer name and model number of your landing gear, I would be happy to speak with one of my contacts at Stromberg to ensure that this...
    view full answer...


Expert Answers about Stromberg Carlson Electric Landing Gear Set - Weld On - 21" Lift - 6,000 lbs - LG-1Do you have a question about this Trailer Jack?



Info for this part was:


Photos by:
Theodore B

Expert Research:
Michael L

Expert Research:
Sarah L

Expert Research:
Michael H

Expert Research:
Jameson C

Expert Research:
John H

Updated by:
Adele M

Expert Research:
Brandon M

Expert Research:
Adam R

Expert Research:
Jeffrey L

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.










Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email





Free Shipping on Orders Over $99

Only 7 Hours 49 Minutes Remaining


etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com