Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"

Curt Trailer Hitch Receiver w/ Euro Drawbar - 1-7/8" Ball - Custom Fit - Class I - 1-1/4"

C111841

Retail:$285.19

Price:$153.18

Curt Trailer Hitch Receiver w/ Euro Drawbar - 2" Ball - Custom Fit - Class I - 1-1/4"

C111842

Retail:$285.19

Price:$153.18

Curt Trailer Hitch Receiver with Standard Drawbar - Custom Fit - Class I - 1-1/4"

C111843

Retail:$264.88

Price:$150.18

Curt Trailer Hitch - C11184

Perfect for light-duty towing, this custom, vehicle trailer hitch receiver features fully welded, gloss powder coated steel construction. Drawbar sold separately.

Features:

• Custom fit is designed specifically for your vehicle
• Precision, robotic welding maximizes strength and improves fit
• Bolt-on installation - no welding required
  • Complete hardware kit and installation instructions included
• Lifetime technical support from the experts at etrailer.com
• Gloss black powder coat finish over protective base coat offers superior rust resistance
• Sturdy, square-tube design
• Drawbar sold separately - pin and clip included
• Made in the USA

Specs:

• Receiver opening: 1-1/4" x 1-1/4"
• Rating: Class I
  • Maximum gross trailer weight: 2,000 lbs
  • Maximum tongue weight: 200 lbs
• Limited lifetime warranty

Note: All non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps. Failure to properly support these loads will void your hitch warranty from Curt.

etrailer.com Technical Support

At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.

11184 Curt Class 1 Trailer Hitch Receiver

This Product Fits The Following Vehicles

2008 - 2011 BMW 1 Series 128i

2008 - 2011 BMW 1 Series 135i

Customers Who Purchased This Trailer Hitch Also Bought...

Curt Upgraded Circuit Protected Tail Light w Converter Hardwire Kit - 4 Pole End (Includes Tester) $47.18

Ask the Experts about this Curt Trailer Hitch
Do you have a question about this Trailer Hitch?

• Which Trailer Hitch and Locking Anit-Rattle Device Fits a 2010 BMW 128i Coupe
  
• The Curt Class I Trailer Hitch Receiver with Drawbar, # 11184, will fit your 2010 BMW 128i Coupe. As far as the rattling goes, we have not received any comments regarding rattling. However, if there is rattling, it could be a few things causing the noise. First, it may not be the hitch, but something that is loose from installing the hitch. If everything is re-assembled correctly according to the instructions (linked below) rattling is less likely. Also, it is important to torque the install
  view full answer...


• Installation Instructions and Details for the Curt Trailer Hitch # 11184 for the 2010 BMW 135i Hitch
  
• On the CURT Class I 1-1/4 Inch Hitch, part # 11184, for the 2010 BMW 135is the under body panels are at the rear of the vehicle underneath behind the rear fascia. Detailed trimming information is provided in the installation instructions (see link). All of the hardware required to install the hitch on your BMW 135i coupe or convertible is included. I have no idea how many of these hitches have been installed on the BMW 135i, but in the last several months we have sold more than 10 of them
  view full answer...


• Instructions for Trimming Under Body Panel on a BMW 1 Series 135i
  
• The under body panel that needs to be trimmed is at the rear of the vehicle underneath behind the rear fascia. The rear fascia itself will not need to be trimmed. Detailed trimming information is provided in the installation instructions, see drawing and instructions link. The best way to trim these parts is to take them off the vehicle and use a Dremel with cut off disc. A steady hand is required, and the edges can be touched up with a small file. A razor knife is also an option, but require
  view full answer...