Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Rating: 




60 reviews
Code: C13073
Retail:$249.65
Price:$149.79
Shipping Weight: 27 pounds
Shipping SpecialThis fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
Specs:
Note: All non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps. Failure to properly support these loads will void your hitch warranty from CURT.
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Replaces C13004
Video of Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Today on our 2012 Hyundai Santa Fe well be installing the Curt hitch, part number C13073. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is four and a half inches. From the top of the receiver tube to the ground is 15 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Now lets go ahead with installation. Before we can install the hitch well first need to lower the exhaust. To lower the exhaust well spray each one of the three rubber isolators with some spray lubricant and then remove them from the metal hanger. Next well need to remove the heat shield above the muffler. There are total of four attachment points for the heat shield.
With them removed and set aside well go ahead and remove the heat shield and mark the area that will need to be cut out so that we can attach the hitch directly to the frame and avoid pinching the heat shield between the hitch and the frame. Well go ahead and use our tape measure and a paint stick to mark out this area, that will be approximately eight inches from the end of the heat shield nearest the bumper. With it marked out well go ahead and cut it out. You can use a pair of tin snips cutters, or well be using a powered cutting tool. With the heat shield cut out well go ahead and reinstall it.
Keep in mind well only be reusing three of the four attachment points as the fourth one was cut off when we cut out the area for the hitch. With our heat shield reinstalled were read y to go ahead and install the hitch. First well go ahead and point out the attachment points. Note each process we do here on the drivers side were going to repeat identically on the passengers side. Well have a total of six attachment points, four in the bottom of each frame rail which will be weld nuts built in by the manufacturer, and two that will go through the frame rail.
The hardware that goes through the frame rail will be out half-inch bolt, flat washer and phalange nut. Well use this to hold our hitch into position. Then we can install the weld nut fasteners. The weld nut fasteners will be new 10 mm bolts along with conical tooth washers. Keep in mind the teeth of the washer will face the hitch. With all our hardware in place well go ahead and tighten it down. Next well go ahead and torque to specifications as indicated in the instructions. With our hitch tightened and torque to specifications we can go ahead and reinstall the exhaust. That will complete the install of our Curt hitch, part number C13073 on our 2012 Hyundai Santa Fe.
2010 - 2012 Hyundai Santa Fe
2011 - 2013 Kia Sorento 4 Cylinder models
2011 - 2013 Kia Sorento V6 EX with Factory Tow Prep Package
2011 - 2013 Kia Sorento V6 EX without Factory Tow Prep Package
2012 - 2013 Kia Sorento V6 LX with Factory Tow Prep Package
2011 - 2013 Kia Sorento V6 LX without Factory Tow Prep Package
2011 - 2013 Kia Sorento V6 SX with Factory Tow Prep Package
2011 - 2013 Kia Sorento V6 SX without Factory Tow Prep Package
Customers Who Purchased This Trailer Hitch Also Bought...
Average Customer Rating: 



4.7 out of 5 stars (60 Customer Reviews)




by: Woodcarver08/31/2011
Is this review helpful?
Placed my order online on Friday (late afternoon). Received my hitch on Tuesday! The hitch was exactly what I expected it to be. Plus, etrailer upgraded my shipping at no extra cost - great service! Also found the same hitch elsewhere for less (total delivered cost) and etrailer promptly credited my order with 110% of the difference. Again- great service! Installation was pretty easy. Great instructions! It took about 1.5 hours. It looks nice too with only a small amount of the round metal tube showing next to the receiver. I still have to install the wiring kit, but based on what I've seen instruction-wise, I am guessing that will go smoothly also. Thanks etrailer for your quality and prompt service!23271




by: Brian S.05/03/2011
Is this review helpful?
Installation was not so easy. Cutting the heat shield was no big deal. My main problem was that the hitch receiver hit the bumper. I had to cut a 3/8" notch out of the bumper so that the hitch could clear. Note from my picture that the notch is not centered - make sure you completely bolt up the hitch before cutting - I used a Dremel and file. Its not critical that its a clean cut - you really don't see it. Also, the spare hits the hitch if it were in its normal position. Probably no big deal, but the spare position is shifted with the hitch installed. Due to having to cut the bumper, I have to rate the install as difficult. If it weren't for that, it would have been a 40 minute job - it took me over 2 hours. The hitch does look good once installed though. 12784




by: Matt V.05/14/2012
Is this review helpful?
The receiver arrived extremely fast albeit a huge package. The directions for installation included vehicle specific good quality color photos along with specific instructions for the installation. As noted there was some trimming to the heat shield along the passenger side frame rail that needed to be done but this was a simple task with some hand shears and could possibly be done with some strong scissors and the heat shield is just thin aluminum. The bolts all went in without a problem, added a little anti-seize for good measure. Overall the process took about 45 mins with two people including the light harness hookup. The receiver is tucked right up to the bottom of the bumper and shows minimal tubing on each side giving it a very clean look from the rear. My only gripe is the receiver tubing does interfere with the spare tire slightly pushing it forward a little. The tire can still tuck all the way up to the underside of the body as it should it just rests against the receiver tube and I wonder if over time the black paint will get worn through from vibration. Only time will tell. Overall I am extremely satisfied with the simple installation and the look of the receiver from the rear. Highly recommend!!!!40320




by: Larry G.03/29/2012
Is this review helpful?
Installation of hitch and full wiring harness went smoothly. No issues that others had mentioned, didn't have to drill out frame or cut away at center of bumper. Also, had plenty of wire, didn't have to splice any additional...trick was to hug the inside of bumper. Watching videos helped to simplify the installation, along with a little patience. Toughest part was to fish the wiring up through the passenger side tail light opening, bent coat hanger worked well. Would strongly recommend etrailer, price was reasonable and installation straightforward.35561




by: Joe C.01/17/2012
Is this review helpful?
Just received Curt Trailer Hitch & T-One wiring harness for my 2010 Hyundai Santa Fe. I will be installing it next weekend. Instructions & videos are quite helpful, looks like a quick install and will look great on vehicle, Shipping was right on time as always ! Thanks, Keep up the good work. Joe C.29850




by: Mike Martin11/26/2011
Is this review helpful?
So simple to make installetion myself. Also with the video available it was great. Thanks for all the support (video and printing diagram)27392




by: Eric R.11/12/2011
Is this review helpful?
I have a 2012 Sorento EX V6. Hitch is sturdy and looks nice when installed. Pushes up against the bumper a little bit, but my bumper is plastic so I wasn't concerned about this. You should know that once the tow hitch is installed, it will be a bit of a squeeze to get the spare-tire into the spare tire compartment. This isn't a big deal, you just need to first tuck the front of the tire above the hitch then wind the cable, pulling the rest of the tire up against the bottom chassis. One down side is that when using this hitch you CANNOT put a full-size tire into the spare tire compartment (e.g. if you have a flat tire or you just wanted a full-size spare). I believe without the hitch, a full-size tire would fit into the spare compartment. Maybe a different hitch from etrailer will have a different shape that would allow you to fit a full-size tire into the spare tire compartment.26866




by: Steve05/13/2013
Is this review helpful?
The hitch installs without excess frustration, and look very discreet. The hitch interferes with the mini spare tire though. The cable that pull up the spare ends up tweaked to one side, and the lifter plate ends up skewed. Curt could bend the tubing on one side to give more clearance with upsetting the aesthetics. Room for a full size spare would be even better.80057




by: Kyle R.04/28/2013
Is this review helpful?
The appearance of this hitch is worth the extra install steps in my opinion compared to the Hidden Hitch or Draw Tite. Two people makes it much easier to install. It pushed up on the bottom of the bumper a little bit but not enough to require trimming on a 2012 Santa Fe. In order to torque the cross bolt on the passenger side I had to have a long extension to get over the top of the muffler. The spare tire rubs on the tube a little bit but I still able to get it back under the SUV. Great looking product.78183




by: John W03/15/2013
Is this review helpful?
All I can say is I love it. I have installed many receivers hitches and this one was the easiest due to the information from etrailer. Lookd great. I like that there are several different ones to pick from. Free shipping made the deal for me.70983




by: Dale03/11/2013
Is this review helpful?
This hitch is perfect. With the excellent instructional videos and on-line instructions provided by etrailer.com, any DIY project is simple. Etrailer.com are excellent to work with. Great company.70026




by: BT03/07/2013
Is this review helpful?
Bolt on as advertised and directions were spot on. Will note in doing this alone it does take a little more time but can be done. Looks good on the vehicle as well-- I had no issues with having to trim anything for clearance other than the heat shield.69392




by: Peter D.01/05/2013
Is this review helpful?
The hitch arrived in good condition. The video was very helpful and the installation went smoothly. I am pleased with the hitch. Great product and great service from etrailer. Thank You62496




by: Keith F.12/29/2012
Is this review helpful?
Very impressed with your website, company and service. I couldn't be more pleased with my purchase. Not only am I satisfied with the product itself, but I am also impressed with the instructional video you offered for my vehicle. It was right on and made the installation a success. Thanks for providing a quality service.62227




by: Terry C.12/26/2012
Is this review helpful?
Shipped the same day I ordered and arrived 3 days later, even with the Christmas rush. The installation video on the web site was a real help. The installation went well and everything fit as advertised. Great service from etrailer.61978




by: Susan C.12/11/2012
Is this review helpful?
shipping was excellent and fast 61203




by: Don Calhoun12/01/2012
Is this review helpful?
Great installation video, easy installation. Didn't have to cut fascia on bumper.60402




by: Chuck B11/30/2012
Is this review helpful?
Liked the item, easy to install. 60364




by: Tino11/14/2012
Is this review helpful?
The main thing here is that I am very satisfied with the hitch itself, looks great and appears to be a very sturdy construction. HOWEVER, here are some things you need to be aware of when buying this particular product. The hitch is pushing against the bottom of the rear bumper quite a bit (pushes it up approx. 1 inch), and actually deforms (without damaging it!) the bumper. Secondly, it also pushes against the spare tire underneath the car. Therefore, installation is not just holding it up and bolting it in place, it actually requires a lot of PUSHING up and bolting it in place. And finally, when it comes to the trimming of the heatshield above the muffler, don't think you will have a ton of room by lowering the muffler. Again, a lot of pushing and pulling is required and I actually never managed to get the heat shield out from above the muffler without detaching the muffler completely. I ended up trimming the heat shileld while hanging loosely between car and muffler. So, all in all, I can definitely recommend the hitch, but the few cues the item description gives you are only telling half the truth about the installation.59445




by: John H.11/06/2012
Is this review helpful?
Other posts note that the spare tire fit is tight, but the Curt tube look is a bit cleaner & tucked underneath more than other brand options hanging below the spare. Welds, & paint finish are A+. Read the posts, then decide yourself.58915




by: Gene11/02/2012
Is this review helpful?
Great communication from the company, super fast shipping!58735




by: Shannon10/14/2012
Is this review helpful?
I have a 2011 4cyl Sorento and everything went really smoothly putting this on my car. I am handy around the house, but I never do anything on the cars, so it took me a while to get the courage to just do it. I did have to cut the heat shield and move the exhaust and tire out of the way, no big deal once I did it. I didn't have to cut any of the exterior trim as it snugged right up under the bumper and fit perfectly. It came with a few nicks in the metal but I am not concerned about it at all. Anyway, just wanted to let the women out there know - you can do this (I did have help holding the part in place while bolting it on)! It took me about 2 hours but I was watching my kids and doing laundry and listening to a good podcast at the same time. E-trailer was great.57193




by: Dennis O.09/01/2012
Is this review helpful?
Hitch fit perfectly on our 2011 Hyundai Santa Fe. Easy install with clear instructions. etrailer has great prices and FAST shipping.53732




by: FRank S.08/27/2012
Is this review helpful?
Installation introductions were very easy to read and use. The installation tool less than 20 minutes.53216




by: Rob S.08/24/2012
Is this review helpful?
The hitch installation was a snap mainly due to excellent instructions from etrailer. Also, the hardware that came with the hitch was top-notch. 52870




by: Bob W08/19/2012
Is this review helpful?
had no trouble with installing the C13073 hitch on my 2013 Sorento all bolt holes lined up , the only thing was that after the hitch was installed the spare tire doe's not fit correctly back up under the vehicle52258




by: Joe08/10/2012
Is this review helpful?
Very easy to install. Took about 1.5 hours by the time you remove the muffler & spare tire and trim the heat shield. Very clean look - tucks up right the bumper and very little is visible besides the receiver. The nice thing about this hitch is you do not have to fish parts through the frame rails, everything is bolt up and go. This is the 4th Curt hitch I've used, very high quality and American made. etrailer is excellent as well - extremely fast shipping and videos of how to install the hitch right in the website.51284




by: Mobile Technologies07/23/2012
Is this review helpful?
Simple installation and good design, a well made in USA product.49037




by: Mobile Technologies07/23/2012
Is this review helpful?
Simple Installation and good design, a well made in USA product.49036




by: Brandon T.07/22/2012
Is this review helpful?
The hitch was very simple and fast to install. It took longer to get the grommets off of the exhaust and trim the heat shield warning than to get the bolts into the frame. I will and have already recommended your products and website to my friends. Super fast shipping too! Ordered on a Monday and received on Wednesday bc it missed the local truck by 20the mins Tuesday morning.48849




by: Bruce W.07/15/2012
Is this review helpful?
I was in a hurry to get this hitch installed on my Kia Sorento because of an upcoming trip. It arrived in short order and in perfect shape. I went immediately to youtube and watched a video posted there. It was very helpful, and the hitch and wiring harness fit perfectly - I had it installed within an hour and a half. Thank you for a great product that did exactly what I needed! 48043




by: Colin C.07/09/2012
Is this review helpful?
Easy to install! I did it while it was storming outside.47326




by: Mike S.07/02/2012
Is this review helpful?
I received my curt hitch and wiring harness by UPS 3 days after my on line order. Used Standard shipping. Very Quick!! Installation of the wiring harness and hitch were exactly as the video's described. Installation was not difficult at all. An extra set of hands helps the trailer hitch installation go much quicker. Great product and great service from etrailer. I will definitely use etrailer again for my trucking needs.46581




by: Albert W,06/29/2012
Is this review helpful?
Installation of hitch, wiring harness, and bracket took about 1 hour. Instructions were very accurate as were the pictures. It goes much easier with someone helping. Hint: use a small rope to fish wiring harness module through tail light housing. Check underneath the drivers side by rear wheel for 2 wiring plugs, this will indicate your Sorento is pre-wired for hitch. Wiring harness plugged in perfectly, except smaller plug needed about 1 inch more wiring to be easier to plug in. Lastly spare tire will rub up against hitch, making removal and installation of spare tire a little tricky. The hitch and harness look professionally installed, very easy to do. Thanks "etrailer"46146




by: Reese L.06/03/2012
Is this review helpful?
Install and the use of the trailer package was a breeze. Just followed the instructions and I was good to go. I will recommend this product/site to friends and relatives. Thanks eTrailer.42535




by: Paul C06/02/2012
Is this review helpful?
This product is a breeze to install. It looks way nicer than the Hidden Hitch/Draw Tight options. I was slightly concerned with lowering the muffler and altering the heat shield, but this process took no time if you follow the video on etrailer (great video). I did this on my own with the vehicle slightly raised for better access. I paired this with the OEM wire harness and the total time to install was about 2 hours. Compare the price to what a retailer would charge for installation and you save some big bucks. The only functional limitation is the inability to use this hitch with a weight distribution system, but I don't think that's an issue if you're towing with a Sorento.42458




by: Gene M.05/27/2012
Is this review helpful?
Product received in a timely manner and installed as advertised. All instructions were accurate and easy to follow. It looks amazing on my Sorento. Kudos to etrailer!! 41784




by: JT05/24/2012
Is this review helpful?
Recieved Curt hitch and OEM wiring from Curt for 2011 Santa Fe. Order was received in 3 business days exactly as advertised. Totally bolt on, no mods required with the exception of trimming the heatshield, which only needs trimmed a few inches, I trimmed a 4x4 section at the rear corner, as I bolted the hitch on without the shield, then only trimmed the shield so it would fit. The half inch bolt they talk about having to enlarge the whole for, fit without having to enlarge the whole. Wiring kit was also ez to install. One could perform this install with 3 wrenches (10mm, 17mm, 19mm), one phillips head and one straight screw driver and a pair of tin snips. It was a little rough to get the hitch in place by myself, tough getting it between the bumber and the muffler. I didn't have the vehicle jacked up but with a little wiggling was able to get it over the muffler, which holds that end in place, so you can lift the other end and get a bolt in it if you are doing it on your own. Took me about an hour and a half, taking my time. Could not imagine using any of the other hitches for any reason. Fit was perfect, and was well built. It also looks great.41548




by: Guy R. Monagas05/18/2012
Is this review helpful?
This product was easier to install than the stock hitch that came with my vehicle. Excellent product.40953




by: mike w04/28/2012
Is this review helpful?
The instructions were very good and made installation very easy, however the hitch is right against the muffler and rattles all the time38714
A lot of times, exhaust hangers are not the exact same shape or in the same location. Although hitchexhaust rattle is not the norm, it is also not unheard of. There are a few tricks that we use in our shop to correct these problems. See the link below.http://www.etrailer.com/faq-fixing-exhaust-rattle.aspx
Patrick B - 11/30/2012



by: John H.04/24/2012
Is this review helpful?
The video helped a lot...instalation took about 1 hour...very good company...THANKS38179




by: Joe E04/21/2012
Is this review helpful?
This was a first time buy from etrailor.com. I ordered two hitches, one for my Outlook and Sorento. They were very reasonsbly priced and shipped for free. They arrived in what seemed like no time at all! I installed them myself, both hitches in one morning. The web site is very helpful having installation videos to watch. Highly recommend etrailor.com. Thank you.37912




by: boating in GA03/30/2012
Is this review helpful?
This is a Quality trailer hitch. Good quality gloss black paint, strong welds and thickwalled tubular steel. I installed it on my 20011 Hyundai Santa Fe.Took my time and finished in an hour. the heat shield is easy to cut with heavy duty scissors. The fit is aligned perfectly with all the predrilled holes matching the frame of the car. Etrailer.com delivered quickly and in good condition. I will use them again for any other acccessories I might need.35646




by: Johnny03/28/2012
Is this review helpful?
Works great, give yourself an hour and get someone to help hold it up. Removing the muffler the worst part. I did it by myself....not to easy, but looks great and work well.35279




by: Tom03/14/2012
Is this review helpful?
Went in great. Arrived as advertised. Great instructions.33858




by: dan03/13/2012
Is this review helpful?
great product and very fast shipping thank you33796




by: Jerry03/11/2012
Is this review helpful?
This hitch is hidden a lot better than others I've looked at and compared even OEM,and is a lot sturdier-REMOVE THE TIRE-for ease of installation,you do not have to cut the bumper,thanks for the video33534




by: bill b.03/11/2012
Is this review helpful?
great hitch, easy to put on, look great and fits like a glove.wiring in kit is very short so let the wires lay on top of the bumper brace.33533




by: Jamie G.02/20/2012
Is this review helpful?
Product was received very quickly and is of great quality. It is very solid, anchored to the vehicle so it will never-ever come off and was reasonable to install. The online video said it would take 20 minutes to install. The instructions said 30 minutes. The reality is, it took about 2 hours to install. That's OK though, the quality of this product made it worth it. You really do need a torque wrench to install this. The bolts require 75 ft-lb of torque and you really can't estimate that without a torque wrench.32008




by: Erik12/26/2011
Is this review helpful?
I bought this hitch for my son, and he and I installed it in less than two hours. He was mostly on his back on the ground. I was mostly talking to him, while he did the work. But it was really good to have two people lift it into place and slide the bolts in. It went really well, the instructions were clear, and the unit fit well. About 3/8" gap better than too tight. There were some scratches in the surface coating, which we sprayed over with primer. No need to cut the bumper as we read one guy did. Too bad for him.28723




by: Pedro Gracey10/07/2011
Is this review helpful?
the product arrived well and as requested, today it fixes my SUV Thank you25206




by: Dan D.09/01/2011
Is this review helpful?
Easy to install and no drilling was necessary. As long as all bolts are started before tightening any of them, they all go in as specified. The unit does push up on the bottom of the bumper, but I do not see that as an issue at this point. 23333




by: George K08/25/2011
Is this review helpful?
Everything they said it was...fast delivery, easy to install (the old fashioned way ...on my back in the garage). Used a short bungy cord at the tongue as an assistant. Ordered on tuesday, installed on wednesday. Great service guys.22777




by: Matt B08/10/2011
Is this review helpful?
My 11 yr old son and I installed this in less than one hour. That was being extra cautious not to scratch anything, ensuring bolt holes were cleaned out, ect.. and explaining things to him. Nice set up and easy to install. 21567




by: Win B08/01/2011
Is this review helpful?
Very easy to install,no drilling 20693




by: Rick D06/23/2011
Is this review helpful?
Received Hitch for 2012 Kia Sorento in only 48 hours from order. This is Excellent, since I live 600 miles from shipping point. Hitch was shipped in large box to protect from damage in UPS Shipment and was received in perfect condition. etrailer.com provided excellent service and prices.17765




by: nireland06/02/2011
Is this review helpful?
Just had this hitch installed and it looks great! Far better looking on the vehicle than either the drawtite/hidden hitches that are the only other alternative. I'd say the installation was moderate in difficulty! There was no cutting of the bumper or removal of sparetire to complete the job..However I used a professional to do it right.. Overall very pleased with the product and its appearance!16008




by: Bob Z05/22/2011
Is this review helpful?
Fit well, took about 45 minutes to install. Would be easier with 2 people, but after doing it once it would go much faster.15042




by: T Pederson05/07/2011
Is this review helpful?
The hitch was easy to install with user friendly instructions. The wiring harness was a breeze as well. These are two really good products for the money and I will definately by from e-trailer.com again. 13052




by: Keith08/17/2012
Is this review helpful?
Nice looking hitch when installed, not quite as easy as I expected. I read that this one required more work than the comparable Hidden Hitch alternatives, but I liked the way it tucked up under the vehicle better. Dropping the spare tire and disconnecting the muffler (not just the rubber hanger brackets, but the bolts to the main tailpipe as well) was required to get this in place. I didn't have to trim the plastic fascia on the bumper, but the hitch does push on it - just not enough to distort it visually from the rear of the vehicle. The spare tire (SE Model w/ 18" tires) does NOT go back into position afterwards (this was warned about in other reviews). I'll need to check on that to make sure it's staying in place for a few weeks until I get the confidence that it isn't going to fall off - but based upon other peoples reviews I don't expect a problem. If I had it to do over, I'd still get this unit for the tucked-under look. If I wanted a faster, simpler install and didn't care about how it looked - I'd get the Hidden Hitch.52061
Ask the Experts about this Curt Trailer Hitch
Do you have a question about this Trailer Hitch?




Related Products...
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.