Trailer D-Ring Tie Down, Recessed Swivel

Brophy Trailer Cargo Control - RR06

Utility Trailer D-Ring Tie Down

• Recessed Ring Swivels 360 Degrees
• Zinc Plated
• Bolt-On Design
• Capacity: 6,000 lbs.
  • Safe Working Load Limit: 2,000 lbs.
• 4 bolt holes are 3-13/16" apart
  • Bolt holes are 1/4" in diameter

Customers compare RR06 to these similar products

Recessed Trailer D-Ring Tie Down with Backing Plate and Hardware, 5K$13.49

Trailer D-Ring Tie Down, Recessed 5K$7.99

Trailer D-Ring Tie Down, Bolt-on, 5K$5.49

E-Track Trailer Cargo Control - Horizontal - 5 Foot Long$14.99

Trailer D-Ring, Light Duty Tie Down$5.09

Customers Who Purchased This Trailer Cargo Control Also Bought...

Backing Plate for RR06 Recessed Swivel D-Ring Tie Down $5.09

E-Track Trailer Cargo Control - Horizontal - 5 Foot Long $14.99

E-Track 2" D-Ring, 3.5K $5.49

E-Track Tie-Off Ring, 4K $4.59

E-Track Plastic End Cap $3.29

Ask the Experts about this Brophy Trailer Cargo Control
Do you have a question about this Trailer Cargo Control?

• Hardware for Brophy Swivel D Rings Part # RR06
  
• Installation hardware is not included with the Swivel D Ring part # RR06 due to the unknown nature of the surface that the end user will attach it to. Depending on the weight of the object that will be held down, and the thickness of the surface it will be attached to, you also might want to consider the backing plate part # BP06.
  view full answer...


• How to Install the Trailer D-Ring Tie Down # RR06 on a Trailer
  
• If you look below the specs for the Trailer D-Ring Tie Down, # RR06, you will see that the lip is wider than the base . You would need to drill a hole that is 4-3/8 inches in diameter for the base to fit through and then use screws appropriate for the surface it is mounted to in order to secure it. It is recommended to use the backing plate # BP06 under the service where the D-Ring is installed to maximize its capacity and offer support. In order to drill out the hole you can use a large enou
  view full answer...


• How to Determine Proper D-Ring Spacing In an Enclosed Car Hauler Trailer
  
• Since you are planning on installing these Trailer D-Rings # RR06 in a plywood floor I would recommend you also get the Backing Plate # BP06 to offer better support than just the wood of your trailer floor. As far as the placement of them in your trailer, you will need to consider what vehicles you will be transporting. If it will be only one vehicle I would recommend loading that car in the trailer and then strategically place the D-rings to give you the best possible mounting points for tha
  view full answer...


• What are the Dimensions of the Brophy D-Ring Tie Down RR06
  
• I pulled the Brophy Trailer D-Ring Tie Down, # RR06, from my warehouse to measure and verified that the diameter of the flange is in fact 6-5/16 inches. I also verified that all other measurements on the product page are correct. I have attached the photo of the dimensions for you to reference. We recommend using the backing plate, # BP06, with this tie-down to provide extra support when securing cargo.
  view full answer...


• How to Mount the D-Ring to a MC10 Motorcycle Trailer for Strapping in a Honda Goldwing
  
• You would need to drill a hole that is 4-3/8 inches in diameter for the base to fit through and then use nuts and bolts appropriate for the surface it is mounted to in order to secure it. It is recommended to use the backing plate # BP06 under the surface where the D-Ring is installed to maximize its capacity and offer support. In order to drill out the hole you can use a large enough hole saw drill bit or use the backing plate as a template and a pencil to mark the diameter needed and use a
  view full answer...


• What Size Mounting Hardware is Required to Install the Trailer D-Ring Tie Down, # RR06
  
• The Trailer D-Ring Tie Down, # RR06, has mounting holes that are 1/4 inches in diameter. We recommend using backing plate # BP06 when installing this tie down to provide support for the tire down.
  view full answer...