Intended for use on 4" square channel bumpers on the rear of many RVs and towable campers, this 2" x 2" hitch receiver is ideal for RV-approved hitch accessories, such as bike racks and cargo carriers. Lowest Prices for the best Specialty Trailer Hitches from Curt. Curt RV Bumper 2" Trailer Hitch Receiver part number E-100 can be ordered online at or call 800-298-8924 for expert service.

Select Your Vehicle

Specialty Trailer Hitches > RV Hitch > Bumper Mount > 2 Inch Hitch > Bolt-On > 350 lbs TW > 3500 lbs GTW > Curt

Curt RV Bumper 2" Trailer Hitch Receiver

Curt Specialty Trailer Hitches

(89 reviews)

Code:   E-100



Shipping Special

Shipping Weight: 11.56 pounds


Curt Specialty Trailer Hitches - E-100

Intended for use on 4" square channel bumpers on the rear of many RVs and towable campers, this 2" x 2" hitch receiver is ideal for RV-approved hitch accessories, such as bike racks and cargo carriers.


  • Has 2" square receiver opening, ideal for hitch accessories such as bike racks and cargo carriers
  • Intended for use on 4" square channel bumpers on the rear of many RVs and towable campers
  • Powder coat finish resists corrosion
  • Includes mounting hardware
  • Weight capacity: 3,500 lbs GTW / 350 lbs TW

Note: For use with RV-approved accessories only. All non-trailer loads - bike racks, cargo carriers and so forth - should be supported with stabilizing straps. Failure to properly support these loads will void your hitch warranty from Curt. Technical Support

At we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.

E-100 dimensions

19100 Curt RV Bumper 2" Trailer Hitch Receiver

Video of Curt RV Bumper 2" Trailer Hitch Receiver

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video Demo Curt Specialty Trailer Hitches E 100
Curt Specialty Trailer Hitches E-100 Review
Video review curt rv bumper trailer hitch receiver e 100
Curt RV Bumper Trailer Hitch Receiver Review

Video Transcript for Curt Specialty Trailer Hitches E-100 Review

Today were going to review part number E-100. This is the Curt RV Bumper 2 Inch Trailer Hitch Receiver. This Curt RV bumper mount trailer hitch has a two inch square receiver opening, which is ideal for RV approved hitch accessories, such as bike racks and cargo carriers. This is intended for use on four inch square channel bumpers on the rear of many RVs and towable campers. It does have a black powder coat finish, which will resist corrosion. It does include the mounting hardware, the two carriage bolts and the two hex flange nuts.This hitch does have a weight capacity of 3,500 pounds gross towing weight capacity and a 350 pound tongue weight capacity.

You will want to check the towing weight capacity of the bumper youll be attaching this to and you never want to exceed the towing weight capacity of the bumper hitch. This hitch also has the elongated holes here on side to attach your safety chains to. I do want to give you a few measurements here. The overall width on this is seven and a half inches. Total from the bottom to the very top is eight inches and the square part to the top is six and a quarter inches.I did mention this will mount on a four inch square channel bumper, so as you can see the width on the inside is four inches.

Just to show you how this would mount, you would insert the carriage bolt through the two holes, use one of the hex flange nuts, square it on and just torque it down and then do the one on the other side. That should do it for review on part number E-100 .

Customer Reviews

Curt RV Bumper 2" Trailer Hitch Receiver - E-100

Average Customer Rating:  4.8 out of 5 stars   (89 Customer Reviews)

Intended for use on 4" square channel bumpers on the rear of many RVs and towable campers, this 2" x 2" hitch receiver is ideal for RV-approved hitch accessories, such as bike racks and cargo carriers.

- E-100

by: Jamie V06/20/2012

Great hitch & easy to install. experience w/ Etrailer & Nicole in particular was fantastic & I will absolutely make future purchase here. If Nicole was closer to my area, I would offer a job in a heartbeat! Many people sell the same products so the difference is service and I have no doubt etrailer has a good training program but she has a natural gift & care to go the extra step to make everything to smooth-very, very impressed. As for the Swagman bike rack- I like the rack & seems very sturdy in construction but it is a loose fit in the receiver. a fastener clamp/tightener should be recommended or added. I had one from a cargo carrier and used that to tighten up the "play" in the receiver area. I could see this being frustrating for anyone that didn't happen to have this part laying around their garage. Delivery was perfect & I plan to load up the rack this weekend. Thanks!! 44982

- E-100

by: RAY K04/13/2012


- E-100

by: Jim M.03/17/2011

I haven't installed this yet but I expect it to work great for my needs-attaching my bike rack to my travel trailer. I'm extremely satisfied with the ordering, price and speed of delivery. Great customer service/email feedbacks from ordering to delivery. The E-100 is heavier/beefier then I expected (very good). And price wise, I had gone to two local hitch stores and was quoted $200 for a similar attachment. The local place also tried to upgrade me to welding to the frame. I don't need to tow anything. I would definitely recommend etrailer. 9565

- E-100

by: Marc Grimm02/13/2012

This hitch receiver is by far the best one available for use on the 4" square bumpers found on RVs. The pull and twisting loads are properly distributed to the maximum possible surface area of the bumper rather than being concentrated at two or four bolt points as with other add-on receivers. With this design the only load on the bolts is dead vertical tongue/rack weight and the bolts are at least two sizes larger than on other designs. Considering the Etrailer pricing on these units there can be no excuse for settling for second best. 31713

- E-100

by: James T11/08/2013

Products received just as promised along with even an upgrade to quicker delivery. Thank you. We have just returned from a 3 week trip to Florida with various stops and the various products we purchased performed just as we had hoped. We have a 2013 Cougar Lite 5th Wheel and were very happy that the bikes were secure the whole time - particularly seeing that we had previously lost bikes off the back of a 5th wheel. 106794

- E-100

by: Ron B.01/26/2015

Great price and fast shipping. I installed this on my 38 foot Fifth Wheel and was worried about how sturdy it was. Once I had it installed on the rear bumper and put the Swagman trail head RV bike rack in the hitch, it was solid. I loaded four bikes and went on our first trip which was 4 hours down the road with no problems. Recommend this unit due to its solid construction not to mention solid mounting hardware. 171280

- E-100

by: chuck g.09/24/2013

This product is AWESOME! I needed a 2" receiver for a bike rack for my RV, I wasn't even sure such a product existed, and found this and it's great. Fit is perfect for a 4" bumper. I had to modify it a tad for upper clearance but that was just for my particular application and was no biggie. This product is really well built. And the service from etrailer is top notch as usual! 101388

- E-100

by: Krash03/21/2015

Product seems to be very stout and well built. Mounted to my reinforced 4" bumper on 2004 Forest River Rockwood Roo. To clear the spare tire, I ordered an extra long ball mount. With everything mounted, the system seems to be very secure. I will be comfortable towing my boat with this. Etrailer's product descriptions and videos are excellent. 180039

- E-100

by: James (Bill) F.03/12/2012

The item is just what I was looking for to add a carrier to the rear bumper of my camper to transport a generator and fuel for the generator. Very easy to install and I am sure will serve me well. I was also very impressed with the service from They upgraded my shipment without additional cost to me. Great Job Folks. 33578

- E-100

by: David R.04/14/2012

Product that I ordered was exactly as as stated in advertisement. Took about five minutes to install and looks good on the back of our coachmen fifthwheel. Bought to carry a swagman four bike rack on the back. Shipping was excellent and tracking and follow up by company was great thanks etrailer. 37157

- E-100

by: Steve H.09/22/2014

Product was exactly what expected, Good solid construction, Installation was very easy. Dealing with customer service with any questions was beyond excellent, Christy B. was very pleasant to talk to and get exactly what I needed. I will be doing more business with e-trailer in the future. 152566

- E-100

by: Steve F.03/06/2012

Nice finish and design. I wish it was a little cleaner at the top of the bumper aesthetically. If there was a way to have the bolts on the bottom instead of the top, it would look better, and give me more confidence. Much better than anything else that I found. 33183

- E-100

by: Curtis D.05/23/2011

Great product, easy to install, only negative, some safety locking nuts would be better than the spin on and torque nuts that were supplied. I did use a safety system to make sure it does not come loose, but your average installer would probably not have access to. 15151

- E-100

by: smolder05/29/2013

If you order one make sure your camper bumper IS EXACTLY four inches square I had to do a lot of filing and grinding to make it fit. When they say four inches they mean EXACTLY FOUR INCHES MAYBE A SMIDGE LESS but it is very heavy duty and will do the job 82429

- E-100

by: Faye S10/10/2011

This was a great experience. I got the Hitch in 2 days. It took me about 3 mintues to put it on my 5th wheel trailer and now i am ready to pull my trailer loaded with my Golf Cart.. I have never dealt with nicer people than they are at e trailer.... 25399

- E-100

by: Kurt K.08/21/2011

Nice/beefy American built hitch. Bought it for a bike carrier but liked the option of being able to tow with it in the future if needed. Was on sale and the price was great. Etrailer has spooky-good and fast shipping and customer communication. 22402

- E-100

by: jeffrey c08/19/2012

I bought this to jerry rig a front hitch onto the r/v for putting a boat into the lake easier. Taking a chance of it working for me was elimated cause e-trailer posts the dimensions on the site. My project turned out easy and very functional 52253

- E-100

by: Dan C.06/07/2011

Product is great! Had the box opened and receiver was mounted in less than 3 minutes. Fits perfects and is exactly what we needed. Fast shipping and excellent customer service from eTrailer as well. Couldn't be happier. Thanks!! 16252

- E-100

by: George Chamberlain07/18/2014

I am very happy with the product I ordered. I was very impressed on how fast order was filled, shipped and received by me. Also, they are very helpful while on the phone with them in giving advice that is great. Sincerely, George 141976

- E-100

by: Jim11/18/2011

This company has there act together, They are the best at delivery times and they keep there promises. Thank you and i will continue to use you for all my hitch needs and everything else that I can get from ya'll. Jim Leadville, CO. 27158

- E-100

by: Gary11/12/2012

Big, solid piece of steel that fit perfectly on my 5th Wheel's bumper. All needed hardward and diagrams included. NOW, if that bumper will hold up, I can tow my dirt bike. 59245


How did it hold up with the dirtbike I need to mount one as well

comment by: Jason - 01/27/2013


I believe he was using his for a trailer and not a dirt bike carrier if that is what you are looking into. At 350 pounds tongue weight capacity a carrier and dirt bike would really be pushing it, that is if there is a carrier manufacturer that tests and approves their carriers for use on an RV bumper. Your RV should have information on the bumper towing capacity. Compare it to the capacity of the hitch and just abide by whatever is less. We have a lot of RVers that tow a motorcycle behind their RV and have no issues. Just watch the ratings.

Patrick B - 2/13/2013

- E-100

by: Mike05/31/2012

I have installed it but not used it yet but I am very happy with the Hitch. I will be using it very soon for a bike rack on the back of my Camper. And later on down the road I hope to use it to pull my Four Wheeler behind the Camper. 42193

- E-100

by: Dennis VB12/11/2013

Received the product in three days. Hitch is "more" than I expected. Material is superb weight and well worth the money which was a "bargin". A great product and I haven't even bolted it on. I have recommended to all my friends. 109926

- E-100

by: Tom S.04/12/2012

attached (sled) onto bump of RV. Bolts are oversized. Front and back supporting plates will take most of the pressure while in transit. Easy install. Will be using it to carry a bike rack in a few weekends. Thank you. 36970

- E-100

by: Norb S12/01/2012

Great product & FAST shipping!!! Bought it for a much better price than at our local RV store!!! This will allow us to use our bike rack on the back of out camping trailer with out welding a reciever on our bumper. 60397

- E-100

by: Gilles L02/28/2014

The quality of this product, the look and the finish are outstanding. I was planning to weld my own, you know what? Forget it. You cannot comme near this bargain even if you do it yourself. I am very happy! 118013

- E-100

by: BT04/03/2014

Well packaged and shipped fast. I initially thought the product was a bit expensive but once I got it I was very impressed by its exact fit and thick steel. Very large heavy duty mounting bolts as well 123541

- E-100

by: Joey R05/03/2012

Product was shipped promptly and was received on excellent condition. Product was easy to install and I would recomment this to any one looking to add a hitch to the read of a travel trailer. 39269

- E-100

by: John M.05/16/2012

5 Stars, Upgraded shiping, delivered in 3 days. Mounted well and very durable. Used for a Dirt bike Carrier and towing boat behind camper. 40674


How much did your dirtbike and carrier weigh total?

comment by: Eli - 07/14/2013


- E-100

by: adam07/12/2012

The receiver is very well built and will do what it is supposed to. It was a little tight to install and I had to use a bottle jack to press it on, but otherwise it worked very well. 47631

- E-100

by: Dave D.06/29/2012

The part arrived only a couple of days after it was ordered. I installed it the same day it arrived. It fit my trailer bumper great. Thanks for the great service and a great product. 46278

- E-100

by: DAVID07/10/2012


- E-100

by: Jim M.09/30/2011

Simple to install, took about 10 minutes. What was amazing is I had standard free shipping and got my order the next day after I ordered. Unbelievable!!!!!!!!!!!!!!!!!!!!! 24915

- E-100

by: Esf11/08/2013

Easy to install and serves my purpose. I will be using it to support added storage. E-traier was extremely prompt in processing and shipping my order. Great service! 106748

- E-100

by: stan r.07/23/2012

Just installed yesterday, looks like a good heavy duty bumper hitch receiver. Will be using it to haul a Honda 3000 generator in an aluminum cargo box behind my camper. 49008

- E-100

by: Bonnie J02/05/2015

Thanks for the quick shipping. This is a heavy duty 4" RV bumper receiver. Can't wait for war er weather to try it out. All good so far. And just what we needed. 172471

- E-100

by: Brian H07/15/2011

Installed the E-100 hitch receiver on our fifthwheel bumper to accomodate our Swagman bike rack.Minutes to install,very easy instructions,and definately quality built! 19502

- E-100

by: Edward E.12/06/2012

Thanks for the speedy delivery. I have not had a chance to install the hitch on my RV yet,but from the way it looks, it is well constructed and should serve my needs. 60798

- E-100

by: Tom B04/06/2012

ordered it on Tuesday and got it on Friday, now that is fast... Probably going to take me longer to find the correct wrench to use than the actual installation... 36395

- E-100

by: Joe Powell08/29/2012

I needed a hitch fast. The girls told me they would personally make sure it shipped right away. I received my hitch 30 hrs later. I will order from etrailer again! 53453

- E-100

by: Gene W06/06/2012

Very user friendly website. The product was easy to find and was shipped and received in excellent time. Great customer service. I will definitely use them again. 43012

- E-100

by: Davy08/08/2014

The bolts were 1/2" too long but I was able to shorten them with a hacksaw. The bumper was too close to the trailer on my unit but it all worked out OK 145216

- E-100

by: Bob P.08/12/2012

Well built product to be used to carry a tray-style bike rack on my trailer. The unit is welded plate and will carry the rack without any trouble. 51466

- E-100

by: Dan03/07/2013

This product is great, It arrived today, installed it in minutes and the bike rack now fits on the back of the travel trailer. Thanks so much! 69572

- E-100

by: Charles C08/22/2012

Product appears to be of excellent quality, very sturdy and well built. I have not put it on my RV yet so I will update this review as I go. 52577

- E-100

by: Ron W.02/14/2011

Outstanding service. Excellent delivery time. High quality product. Would definitely recommend and will personally use again in the future. 7142

- E-100

by: Bruce R.10/31/2012

VERY well built and the finish is excellent, fit well and will do exactly what I wanted (cargo/generator carrier on my trailer). Thankyou 58481

- E-100

by: Henry Cornelius11/02/2013

service from e trailer was great. delivery was fast and on time.I am sure that in the future I will be dealing with e trailer again 106042

- E-100

by: Christopher02/28/2013

This product does exactly what it is suppose to do. Great product that fit perfectly on my 4" channel bumper for my camper. 68182

- E-100

by: Scott08/07/2008

measure your bumper first make sure you measure your bumper first - my bumper was over 4" square and the product did not fit. 1150

Show More Reviews

Ask the Experts about this Curt Specialty Trailer Hitches
Do you have a question about this Specialty Trailer Hitches?

  • Trailer Hitch Recommendation for Use on the Back of a Crossroads 5th Wheel Trailer
  • We have a couple of different options in terms of trailer hitches for 5th wheel trailers. The Curt Hitch, # E-100, that you have referenced is designed to fit on 4 inch square channel bumpers. You will need to check to see if your bumper fits this description and if it is rated for this application. I recommend going with a frame mount hitch. The most versatile frame mount hitch we offer is Curt Hitch, # 13703. It can be bolted or welded on and fits C-channel, I-beam, and Box frames....
    view full answer...

  • Trailer Bumper Mount Bike Rack Recommendations for a Camper with Rear Mounted Spare Tire
  • If your bumper is rated for towing and/or carrying weight, we offer several bike rack options that are rated for use behind a trailer or RV. Take a look at the Swagman Around the Spare Mighty Rack, # S80500. This rack is designed to fit a 4 to 4-1/2 inch continuous welded square bumper and fit around the spare tire. I have included a link to the installation details for reference. Another option is the RV Bumper 2 Bike Rack, # S80605, or Swagman 4 Bike Carrier RV Mounted Bike Rack, #...
    view full answer...

  • Will the # 64025 Swagman RV 2 inch Receiver Bumper Mount Adapter Mount Underneath the RV Bumper
  • One option we have for mounting a receiver under the bumper of your RV is the RV Bumper 2 inch Trailer Hitch Receiver, item # E-100. The only problem I see with the location you are suggesting is the distance from the bottom of the receiver to the road surface. If there is not enough clearance the clamp on hitch, bike rack shank or bikes themselves may make contact with the road and damage one or all of the components including the RV bumper. I spoke with my contact at Swagman and was...
    view full answer...

  • Will a Trailer Hitch Fit On A 2011 Jayco 256RKS Trailer Rear Bumper
  • The Hidden Hitch, # 82201, is a frame mount hitch. It is designed to be installed to the trailer frame for it to be rated for 3,500 lbs. gross towing weight and 300 lbs. tongue weight. It is not designed to attach to an RV bumper. You can measure on your Jayco trailer to determine if the Hidden Hitch, # 82201, will install to your trailer frame. The frame brackets will fit frame widths from 47 inches to 71 inches. To determine how far from the ground the receiver would be is the...
    view full answer...

  • Bumper Mounted Hitch Recommendation to Tow a Small Trailer and a Golf Cart
  • The main purpose of the Swagman Bumper Mount Adapter, # S64025, is to carry a bike rack behind your RV and it should not be used for towing. Instead, I would recommend installing a universal RV trailer hitch like the Curt Adjustable Trailer Hitch, # 13703, if you are looking for a hitch for an RV. This hitch will fit frames 22 inches to 72 inches wide and it has a 3,500 lb towing capacity and a 350 lb tongue weight capacity. For a bumper mounted receiver, you can look at the Curt...
    view full answer...

  • Whats the Difference Between Curt Hitch E-100 and C19101
  • The difference between the Curt RV Bumper Hitch # C19101 and the Curt RV Bumper Hitch # E-100 is the application. If you have a 4 inch square bumper you would want the # E-100, if you have a 2 inch x 4 inch rectangular bumper you would want the # C19101. If you check out the pictures I attached you can see how the mounting plates are different distances apart.
    view full answer...

  • How to Determine the Compatibility of 2 RV Bumper Trailer Hitch Receiver E-100 With a Pop-Up Camper
  • Yes, the Trailer Bumper Hitch Receiver, part # E-100, can be used on towable pop-up camper units with up to a 4 inch square bumper. However, you cannot exceed the limits of your camper bumper. The bumper towing and tongue capacities may be indicated on the bumper itself, but if not you could check your camper owner manual or contact the manufacturer of your camper. You can view some general information on towing and the rest of the RV bumper hitches we offer at the links provided.
    view full answer...

  • Receiver Hitch for Rear of Jayco 22 Foot Camper
  • There are a few solutions for adding a receiver to the rear of your camper. You will first need to contact Jayco to determine the capacity of your bumper. If the bumper is steel, and has adequate capacity, you could have the 6 inch combo bar you referenced welded in place. However, this piece is sold as a fabrication part only and it would be up to you or the welder to do the engineering work to determine if the receiver will have the necessary capacity. Another option would be to...
    view full answer...

  • Recommendation for a Trailer Hitch that Mounts to a Bumper Pull Hitch
  • It sounds like you are describing a bumper hitch with a ball. What you can do is remove the ball and install Curt Bumper Hitch, # E-3S. This will provide a 2 inch trailer hitch receiver that you can use with a hitch mounted bike rack. I have included a link to the installation details for the hitch. If you have an RV or trailer that has a 4 inch square channel bumper, you could use RV Bumper Trailer Hitch Receiver, # E-100. Or, if it is a 4 inch square continuous welded steel bumper,...
    view full answer...

  • Capacity of Swagman RV Bumper Trailer Hitch # S64025 with Anti-Rattle
  • I spoke with my contact at Swagman, the manufacturer of the RV bumper trailer hitch # S64025, and he stated that the capacity is going to be about 100 pounds, but no higher. So if your cargo carrier and generator are 200 pounds, I would advise against installing this particular hitch for your application. We have another bumper mounted hitches that would be a bit more heavy duty. The Curt RV bumper hitch # E-100 could handle up to 350lbs of tongue weight. We do also carry frame mounted...
    view full answer...

  • Trailer Hitch for Towing a Trailer Behind a 2006 Rockwood by Forest River Travel Trailer
  • I cannot make a recommendation for pulling a trailer behind another trailer. I know it is done, but there are many things to take into account when thinking about this endeavor. You will need to contact the trailer manufacturer to see if the bumper will have enough capacity to handle the loaded trailer weight and tongue weight. I am sure you will be told that it will not. You should also consider that sway can be a big problem when towing more than one trailer and proper loading of...
    view full answer...

  • Hitch Options for Open Range 399BHS Travel Trailer
  • We offer several different options for installing a hitch on the rear of a camper or RV. If you click on the provided link, you can see the available options. Current pricing information is listed on each product description page. Frame mounted hitches like the # 13703 are a good option if the frame members of the camper are within the width range for the hitch, which is between 22 and 72 inches in this case. Although various frame mounted hitches carry a tongue weight capacity ranging...
    view full answer...

  • Curt Bumper Mounted Receiver Part # E-100 for Towing Small Boat Behind RV
  • The Curt bumper mounted receiver part # E-100 will serve that purpose. The receiver itself provides a 3500 lb towing/ 350 lb tongue weight capacity. This assumes that the 4 inch bumper on your RV has sufficient capacity to safely tow the towing/tongue weight of your boat and trailer. I would recommend checking with the RV manufacturer regarding the capacity of the bumper if it is not mentioned in the owners manual.
    view full answer...

  • Hitch and Bike Rack Recommendations For Carrying 2 Bikes on the Bumper of an RV
  • We sell RV bumper hitches that would work well for you to carry an RV rated bike rack at the rear of your Montana 5th wheel trailer. If you have a 2 inch square bumper I would recommend the Curt Hitch part # C19101. If you have a 4 inch square bumper I would recommend the Curt Hitch part # E-100. Now for a bike rack you will need to get a rack that is rated for use behind an RV. The ride is much rougher at the rear of an RV when compared to a passenger vehicle, so a rack not rated for...
    view full answer...

  • Will RV Bumper Mount Trailer Hitch # E-100 Fit a 4 Inch by 2 Inch Bumper on a Trailer
  • I do have a possible solution for adding a trailer hitch to your trailer but # E-100 will not fit because the bumper on your trailer needs to be 4 inches by 4 inches (100mm x 100mm). I recommend installing a frame mount trailer hitch, # 13703. This hitch can be welded or bolted to the frame of a trailer provided the trailer frame is 22 to 72 inches wide. If welding, the hitch should be installed by a qualified professional welder. I have included a link to the installation details for you...
    view full answer...

  • Bumper Mount and Frame Mount Trailer Hitches for a 2011 Volkswagen Tiguan
  • On most vehicles, the bumper beam is attached to the vehicle frame. A hitch that attaches to the bumper beam (a lot of Jeep and Dodge truck applications are like this) is just as safe and secure as a frame mount hitch. It would take an impressive amount of force and one heck of a crack in the road to pull the bumper off of a vehicle, provided the hitch is installed correctly. Your mechanic may be thinking of a hitch that attaches to a square bumper like # E-100. You would not use this...
    view full answer...

  • What is the Weight Limit on Ultra-Fab 2 Inch Motor Home Trailer Hitch Receiver
  • The Ultra-Fab Motor Home Trailer Hitch Receiver, # UF35-946401, was designed with the RV/trailer application in mind. As such the additional torque from accessories bouncing in the receiver was taken into account when the weight capacity of 200 pounds was given to the hitch. You might want to consider going with something rated a little higher, like # E-100, or # UF35-946402, which both have a 350 pound capacity, because with your intended load you will be getting close to the tongue...
    view full answer...

  • Comparing Curt Bumper Mount Trailer Hitch E-100 and Frame Mount 13703
  • Both the frame mount hitch # 13703 and the bumper mount # E-100 have 2 inch receivers. Both are rated for 350 pounds tongue weight and 3,500 pounds gross trailer weight. The bumper mount E-100 is more limited as to what it will fit on. First, the bumper has to be rated for use with a hitch. It must be a 4 inch square continuous welded steel bumper. A bumper mount hitch in general is not as stable as a frame mount. The frame mount 13703 can be bolted or welded on. It fits box frames,...
    view full answer...

  • Will Curt Bumper Mount Trailer Hitch # E-100 Fit a 4-1/4 Inch Bumper on a Starcraft Starsteam 24QB
  • The Curt hitch # E-100 needs a 4 inch square continuous welded steel bumper to install safely. If by removing the decorative trim, you are left with a 4 inch square continuous welded steel bumper, then this hitch will work for you. Be sure to check the owners manual to determine if the bumper can be used for this application. the safest option is to go with a frame mount hitch. I have included a link to the options for you. The most popular is Curt hitch # 13703 because it fits a wide...
    view full answer...

  • Hitch-Mount Cargo Carrier That Measures 48 x 36 for Toyota FJ Cruiser with 2-Inch Receiver
  • The 2-inch hitch-mount cargo carrier that is nearest to your target dimensions of 48 x 33-inches is the ProSeries 48 x 32 Ramped Carrier # 5801600. I have linked a video on this item for you. We do not offer any cargo carrier that is 36-inches wide. I have provided you with a link to our main page for all carriers that will fit a 2-inch hitch. You can use the filters in the left-hand margin to narrow the results based on style and type of carrier, dimensions or weight capacity.
    view full answer...

  • Mounting Orientation of Curt RV Bumper 2 Inch Receiver Part E-100
  • The Curt RV Bumper 2 Inch Receiver, part # E-100 is designed for a 4 inch square channel bumpers. The Receiver is designed to be attached so that the receiver is below the bumper. Although the receiver is rated at 3500 lbs towing and 350 lbs of tongue weight, you will need to check the RV owners manual for the capacity of the bumper. If the capacity of the bumper is less than 3500 lbs or 350 lb of tongue weight, you will need to abide by the lower rating.
    view full answer...

  • Will The Thule Spare Me 2 Bike Carrier, # TH963PRO, Fit On A Spare Tire On A Trailer
  • The Thule Spare Me 2 Bike Carrier, # TH963PRO, is not designed for use on the back of trailers. The reason is that the bike rack is subjected to more jarring and rattling on the back of a trailer spare, which would put more stress on the bike rack then what it was designed for. If you have a 4 inch to 4-1/2 inch square, continuous weld bumper on your RV you could use the Swagman RV Bumper 2 Bike Rack, # S80500. It will not work on aluminum or spot welded bumpers. This bike rack is designed...
    view full answer...

  • Can the Swagman 64685 Platform Bike Rack be Mounted on the Back of a 5th Wheel Trailer
  • The Swagman approved platform bike carrier for the back of a fifth wheel camper is Swagman # S64663. While speaking with Swagman, I was informed that they do not recommend any folding/tilting racks be used on the rear of a trailer or motor home because the additional bouncing and rattling at the rear of the trailer can either break or loosen the pin holding the bike rack upright. The Swagman # S64685 that you referenced has a tilt feature which is the weakest point of the rack and is...
    view full answer...

  • Receiver Needed for 5th Wheel with 4 Inch Bumper with 5-1/2 Inch Drop
  • Given the 5-1/2 inch distance between the bottom of the frame members and the bottom of your bumper, the # 13703 will not fit your application. The E-100 you mention is intended for use with 4 inch square bumpers, as well as the Ultra-Fab # UF35-946402. If you have clearance problems at the rear of the bumper, the Ultra-Fab receiver might be a good alternative as it connects to the underside of the bumper using U-bolts, rather than slipping around it like the E-100 does. Either receiver...
    view full answer...

  • Hitch Recommendations for a Scamp Trailer Bumper
  • Depending on the dimensions of your trailer's bumper I believe we could have a solution for you that would not require welding. If you have a 4 inch by 4 inch bumper you could use the part # E-100. If you have 2x4 inch bumper you could use the # C19101. These have 2 inch openings though. For a hitch opening that measures 1-1/4 inch that would require welding on you would want the part # E-911. You will need to make sure that the bike racks you plan on using are rated for use on...
    view full answer...

  • Will Curt RV Bumper Hitch with 2 Inch Receiver fit my North Trail by Heartland RV
  • The Curt E-100 Trailer Hitch Receiver is meant to be used on 4 inch square channel bumpers. You will need to measure your bumper and check to see if it is 4 inches square. The maximum capacity of this hitch is 350 pounds tongue weight and 3,500 pounds gross towing weight. Check the owner manual of the trailer and see what the bumper capacity is. If it is less, you must abide by the lower number. Make sure whatever bike rack or cargo carrier you will be using is built for use on the...
    view full answer...

  • Can I Use the SportRack Spare Tire Mounted Bike Rack, Part Number SR2813 on a Pop Up Camper?
  • The SportRack Spare Tire Mounted 3 Bike Carrier is not designed to be used behind a towed trailer. A bike rack on a towed trailer or camper is subject to much more jarring and vibration than a rack installed on the towing vehicle. If you were to use this rack on the rear of your camper it would eventually fail, possibly causing loss of the bikes and injury. We offer racks with a 3 bike capacity that are designed for use on a towed camper, but they would involve adding a receiver to...
    view full answer...

  • Bolt-On Frame Mounted Trailer Hitch for a Nash 5th Wheel Trailer
  • First I have to tell you that in many states it is illegal to tow one trailer behind another trailer for safety reasons. You will need to check the laws in your state and the states you will be traveling in to see if you can even do this. The best frame mount hitch that fits the description of what you need is Curt hitch # 13703. It is the most versatile because it fits frame widths from 22 inches to 72 inches. It will fit box, C-Channel, and I-Beam frames. And it can be bolted or welded...
    view full answer...

  • Will the Curt RV Bumper Hitch, Part E-100, Clear the Spare Tire Support on My RV
  • The hitch pin of the RV Bumper Hitch, part # E-100 would fall approximately 1-1/2 inches behind the front face of the bumper. You will want to measure from that point out to where it will clear the spare tire support. Compare this measurement to the shank on your cargo carrier. If the distance from the pin hole on the cargo carrier shank to the closest edge of the basket is greater than the clearance measurement you made, you should be fine. Using an extension, like part # HE06 is possible....
    view full answer...

Info for this part was:

Expert Research:
Michael L

Expert Research:
Sarah L

Expert Research:
Robert G

Expert Research:
Patrick B

Expert Research:
Michael H

Installed by:
Jeff D

Expert Research:
Reno H

Expert Research:
Jameson C

Updated by:
Laura H

At we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.

Stay Connected

Subscribe to email newsletter


privacy - we don't send unsolicited email reviews

All images, layout and content copyright