Holland Fifth Wheel King Pin - fw0030
Holland Retractable King Pin
The Holland Retractable King Pin disappears into the truck bed when not in use and is to be used with inverted Fifth Wheel trailers equipped with Holland #s FW0001 and FW0002-45.
- 2" SAE King Pin - the industry standard
- 14" x 14" Plate
- 4 Bolt
- Measures 12" from center of bolt hole to center of bolt hole
Customers compare fw0030 to these similar products
Ask the Experts about this Holland Fifth Wheel King Pin
- How Is Retractable King Pin FW0030 Raised and Lowered
- I checked with my contact at Holland, and the retractable king # FW0030 will include a threaded handle that you would use to raise the pin from the storage position. Simply screw in the handle and pull up.
To lower the pin after towing, you would just step on the pin, pushing it back down into your truck bed.
view full answer...
- Will Holland Truck Bed Retractable King Pin, # fw0030 work on a Holiday Rambler 5th Wheel Trailer
- If your Holiday Rambler 5th Wheel trailer has a Holland inverted coupler, then the Holland Truck Bed Retractable King Pin, # fw0030 will work.
The Holland Truck Bed Retractable King Pin uses an SAE 2 inch standard king pin. To install the fw0030 you will need to attach the unit to an underbed mount that must be fabricated to handle the capacity of your trailer. I recommend a qualified installation technician to perform this task.
view full answer...
- How Does the King Pin Extend and Retract on the Holland Truck Bed Retractable King Pin, # fw0030
- The tube-like structure on the bottom of the Holland Truck Bed Retractable King Pin, # fw0030, is a housing for a spring and rod or plunger that holds the retractable king pin down when not in use, and props it up to allow the trailer to couple to it.
There is a handle that threads into the top of the king pin to pull it up. The force required to pull it up and overcome the pin holding it down can be achieved by an individual person. When ready to retract the king pin, you simply apply enough
view full answer...
- How is Holland Truck Bed Retractable King Pin, # fw0030, Installed
- To install the Holland Truck Bed Retractable King Pin, # fw0030, you will need to make sure there is at least 6.625 inches of clearance below the bed, when the bed is loaded down, at the center of the rear axle where the king pin will be when retracted. Checking the clearance with a load will ensure that the suspension can work properly and no damage will come to the rear end when there is up and down movement.
You will need at least a 1/4 inch thick steel plate, at least 36 inches wide by 50
view full answer...
- What Fifth Wheel Hitch Assembly will Also Allow Use of a Camper on a 2002 Dodge Ram 2500 4x4
- If you have the 8 foot bed on your 2002 Dodge Ram 2500 4x4 Extended Cab I would recommend to use the Reese Elite Series Fifth Wheel Hitch, part # RP30142 and Reese Installation Kit, part # RP30069. This fifth wheel setup will use a custom, under-bed installation kit that will allow full use of your truck bed after the hitch is removed.
Once the under-bed rails are installed on your vehicle it is just a matter of removing the hitch from your truck bed to install your camper. The fifth wheel h
view full answer...
- Compatible Couplers for Truck Bed Retractable King Pin Part # FW0030 for use with Gooseneck Trailer
- The Holland Binkley Inverted Fifth Wheel Hitch, part # FW0002-45 is compatible with your retractable king pin.
The gooseneck trailer coupler would require some modification so that the inverted fifth wheel hitch could be welded to it. If your existing gooseneck coupler is height-adjustable, a length of 4 inch outside diameter tubing or pipe with could be fabricated with a plate and gussets welded to the bottom. The inverted fifth wheel hitch could then be welded to the bottom plate. This fabr
view full answer...
- How Does the Holland Truck Bed Retractable King Pin, # fw0030, Install and Operate
- The retractable king # FW0030 will include a threaded handle that you would use to raise the pin from the storage position. Simply screw in the handle and pull up.
To install the Holland Truck Bed Retractable King Pin, # fw0030, you will need to make sure there is at least 6.625 inches of clearance below the bed, when the bed is loaded down, at the center of the rear axle where the king pin will be when retracted. Checking the clearance with a load will ensure that the suspension can work pro
view full answer...
