Select Your Vehicle
view cartView Cart

Electric Winch > 2012 > Polaris > 800 Sportsman

Superwinch Winches for the 2012 800 Sportsman by Polaris

Superwinch Winches

ratingratingratingratingrating (3 reviews)


Code:   1120210

Retail:$169.95

Price:$124.95


Shipping Special

Shipping Weight: 20 pounds

Quantity: 






Superwinch LT2000 ATV Winch, 2,000 lbs - 2012 800 Sportsman by Polaris

Superwinch LT2000 12v Winch

T-Series winches give you more value per dollar than anything on the market.

Features:
  • Powers Load IN and OUT
    • Includes freespooling clutch for fast wire rope payout
  • High efficiency low amp draw motor
  • Full-metal planetary gear-train
  • Sealed, handle-bar-mounted rocker switch
  • Dynamic brake
  • Circuit breaker protected
  • Includes Pulley Block, D-Shackle and Roller Fairlead
    • Fairlead requires mount kit (SW87-42616; sold separately)
Specs:
  • Rated Line Pull (single line): 2,000 lbs.
  • Motor: 1.00 hp
  • Gearing: Differential Planetary
  • Gear Ratio: 153:1
  • Freespooling Clutch: Pull and Turn
  • Braking: Dynamic
  • Wire Rope: 5/32" x 49' with latched hook
  • Switching Method: protected relay
  • Dimensions: 11" long x 4.1" deep x 4.1" high
  • Warranty: 1 year
Recommended Accessories:
  • Accessory Kit with Leather Gloves (1554)
  • Mounting System for ATV

1120210 Superwinch ATV Recovery Winch

Replaces Model T2000 (# 1220200)



Video of Superwinch LT2000 ATV Winch, 2,000 lbs


Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video install superwinch atv winch 2012 polaris sportsman 1120210
Superwinch LT2000 ATV Winch Installation - 2012 Polaris 500 Sportsman
Video install superwinch lt2000 atv winch 1120210 2202889
Superwinch LT2000 ATV Winch Installation - 2011 Honda Rancher

Video Transcript for Superwinch LT2000 ATV Winch Installation - 2012 Polaris 500 Sportsman

Today on our 2012 Polaris Sportsman 500 we'll be installing the Superwinch LT2000 2,000 Pound 12-Volt DC Electric Winch. This is part number 1120210. Now with this winch we'll also need to use a mount kit, part number 2202900 for this Polaris. We're going to go ahead and mount our winch to the mounting kit first. Now we'll need to identify the top of the mount plate. This is easily done by locating the cutout here on the angled part of the mount plate.As we install the winch into the mount plate we'll ensure that the cable spools off the top of the drum and that this cutout is on the top side of the bracket.

Now with that done we'll place our rear support plate into position where we'll take two of the 5/16 x 3/4 inch Hex bolts from the winch kit as well as the two flat washers, two lock washers and the nuts and we'll secure them together through the center mounting points on either side.With that done we'll go ahead and tighten them down using a wrench and ratchet. With both bolts tight our mounting plates and winch are secured together. We can go ahead and mount the fairlead. The fairlead is where the winch cable will pass through allowing the cable to move freely without binding up. We'll need to pass the cable through the fairlead.

You may need to loosen up the lower roller in order to do so.With a ratchet and wrench we'll undo the bolt, slide the roller out of the way, pass the cable through, putting the roller back in place and tightening down the bolt and nut. Don't make this too tight because you do want the roller to move freely. We'll mount the fairlead to the main winch mount plate. We'll position it where we can then pass the 3/4 inch bolt through both brackets and we'll put a nut on the other side.Our entire assembly is complete and we're ready to mount it to the ATV. Here at our ATV we'll slide the winch into position here in the hole that we found after removing the black plastic cover from the ATV.

This cover is removed by simply undoing the four torqued bit bolts, two on the upper and two on the lower to get it out of the way. Our winch is positioned and you'll see in the frame of the ATV bolt holes already pre-drilled for us.We can now use the remaining four 3/4 inch bolts, pass them through the holes that were pre-drilled in the frame and into the rear support plate of our winch. With all four bolts in position we'll go ahead and tighten them down. Now that they're tight our winch is secured to the ATV and we're ready to wire it up. We're not permanently installing this winch onto this ATV.

However during this video we will show you what wires connect where as well as a good location to mount the switch and the switch box for the winch.We'll now move to the top of the ATV where we'll remove the seat. With the seat removed we can move to the driver's side of our ATV here at the rear fender and looking underneath you'll see the battery. You'll also see where the positive battery terminal connects to our battery. We'll need to go ahead and undo that and remove the positive terminal. With that done we'll need to locate the pre-wiring that Polaris put into the ATV for a winch.This wire is red in color and is approximately the same size as the battery positive cable. We'll now route that cable up towards the battery, bring it out to where the positive battery terminal is here on the driver's side rear fender where we can then leave it as is to be hooked up later. We'll now move back toward the front of the ATV where we'll open the front hatch, remove the rubber seal, undo these four torques bolts and take out the center plastic trim here. This will expose the radiator cap as well as all the wiring here underneath the headlight.These two orange wires here from the Polaris are both ignition source voltage. Keep that in mind as we will need to tap into one of those two wires at a later time. We'll now take the solenoid box and mount it. You'll notice in the bottom here of the compartment are two drain grommets. We'll go ahead and remove those grommets that work very nicely to pass the red and black wires for both the battery positive and negative as well as the winch positive and negative cables through.At this point you would want to go ahead and screw the solenoid box into the body of the ATV but again because we're not installing this permanently on to our ATV we're just going to go ahead and place it using a piece of double-sided tape to show you what it would look like mounted. You'll want to make sure the box is low enough so that when the lid closes it doesn't come in contact interfering with the way that the lid would latch.We now have our four wires down here underneath the driver's side front fender. Just for demonstration purposes we're going to go ahead and remove this inner fender liner just to give you a little more visibility. When installing yours you may not need to do this. The two long black and red wires are the wires that would connect to the winch. The shorter wires are the wires that will connect to battery voltage as well as your negative ground.Now with the pre-wiring here on our Polaris we'll go ahead and take the two short wires and using the circuit breaker we'll connect the two ends of the wires together. Now remember when connecting the circuit breaker in you do want to keep the copper side of the breaker toward the battery and the aluminum side of the breaker toward the winch. This will ensure the correct operation of your circuit breaker.Now with that done you'll want to tape it back up and ensure that it won't come in contact with any metal objects as that could cause a short. Now we'll connect the two black wires with the bolt through the ring terminals although because this is not a permanent install we'll not be doing that. Now the longer two wires we'll connect to the winch. Because our solenoid box is mounted up front these wires are especially long.If we we're mounting this to the vehicle permanently I would cut these wires to fit where I could then attach it to the winch. Now that we have them attached to the winch and our battery's connections made we can go ahead and reinstall the inner fender liner making sure that we keep the wires tucked away nicely. We'll move back up here where we'll need to install the operation switch.The switch is designed to be mounted in various positions depending on comfort. We'll locate a suitable position here on the handlebars and attach it. This will give us plenty of room to operate the switch as well as leave clearance while we're operating our ATV and having fun. We can then route the wiring down through the headlight assembly and into this space. We'll continue routing the wiring through and down the main harness where you'll take the red wire here and attach it to one of those two orange wires we talked about earlier.Now this connection will just ensure that the winch will only operate when the key is in the on position. Now that we've made that connection we'll continue routing our harness down underneath following the main harness of the ATV until we reach the underside of the front carriage compartment. We'll then go and locate the other black plastic grommet where we'll remove the grommet and pass the remaining harness back up through it.Now in the compartment we'll locate the green wire and the black wire from the solenoid box and connect the green wire from our harness to the green wire on the solenoid box as well as the black wire from our harness to the black wire of our solenoid box. Now that we've done all that we'll go ahead and just make sure that the harness is tucked away where we can re-assemble our ATV and that completes our installation of the Superwinch LT2000 ATV Winch, part number 11020210 in Conjunction with the Superwinch ATV Winch Mount Kit, part number 2202900 on our 202 Polaris Sportsman 500.


Customer Reviews

Superwinch LT2000 ATV Winch, 2,000 lbs - 1120210

Average Customer Rating:  ratingratingratingratingrating4.3 out of 5 stars   (3 Customer Reviews)




- 1120210

ratingratingratingratingrating by: Ed S.04/08/2014

Is this review helpful?


I installed the Superwinch LT 2000 on a 2007 Honda Rancher and also the mounting kit # 2202889. The install went well. I had never put a winch on an ATV before. The video on etrailer was very helpful and would have been difficult to install without it. The instructions that come with the winch and the mount kit are minimal. I found the electrical wire length to be enough as I mounted the solenoid right behind the battery under the seat. The pink wire on the ignition was what I used to tap into to run the switch.124317



- 1120210

ratingratingratingratingrating by: dan m08/08/2013

Is this review helpful?


everything went well till wire and solenoid 93956



- 1120210

ratingratingratingratingrating by: TOM03/28/2013

Is this review helpful?


Product as described. Great customer relations. Immediate shipment. Pleasure doing business with. Have placed an additional order.73060



Ask the Experts about this Superwinch Winches
Expert Answers about Superwinch LT2000 ATV Winch, 2,000 lbs - 1120210                                           Do you have a question about this Winches?


  • Is there a Winch Mounting Plate Available for the 2002 Honda Rancher that Fits Inside the Push Bar
  • I spoke with my contact at Superwinch and he sent me the instructions for the Superwinch ATV Winch Custom Mounting Kit, item # 2202375. In the instructions you can see that the winch will mount inside the front push bar and that the roller fairlead will be attached to the front of the winch mount and stick out just a bit. The mount for the roller plate is included with the # 1120210 ATV unit.
    view full answer...

  • Which Winch Will Work When Pulling a 950 Pound Boat Up a Trailer and Will Wiring Reach the Battery
  • The Superwinch LT2000 ATV Winch, # 1120210, has accessories more suited for ATVs, and the wiring included may not be long enough to reach the battery, let alone the cigarette lighter if mounted in the front. If mounted in the back it would really be a stretch. It does have a single line capacity of 2,000 pounds, so pulling a 950 pound boat should not be a problem. The matching winch for a vehicle is the Superwinch LT2000 Electric Utility Winch, # 1220210. It is essentially the same winch just
    view full answer...

  • Using Bumper Winch as Hoist
  • I would be very leery about using a bumper winch for this purpose. These winches are designed to pull, not lift. We offer a Crane Winch, part # 03002 that would work for this purpose, but it would need 12-volt DC power to work. I believe your best bet would be to find you a 110V electric hoist with sufficient capacity for the barrels and cases of soda.
    view full answer...

  • How to Wire SuperWinch LT2000 and Install On a 1997 Honda 300 4Trax
  • To connect the hot wire or Red wire of the Rocker Switch, you will connect it to the wire in the ignition switch that only is powered when the ignition is in the ON position. To determine which wire this is, you will need to use a circuit tester, item # 3808. If there is a headlight mounted between handlebars there is easily easy access to an ignition source inside headlight housing. Then, you will connect the Green wire on the rocker switch to the Green wire on the Solenoid. The Black wire o
    view full answer...

  • How to Extend the Wiring of a LT200 Superwinch # 1120210 on a 2005 Yamaha Wolverine 350 FX
  • The best way to extend the wiring would be to get 10 Gauge Blue Primary Wire, part # 10-1-1, to extend the wiring and then use a 12-10 Gauge Butt Connector, part # 05732-2, to connect the wires. And then finally wrap the connection with Electrical Tape, part # BT66. That should give you the additional 12 inches you would need to connect your Superwinch LT2000 ATV Winch, part # 1120210, to your 2005 Yamaha Wolverine 350 FX. I attached installation instructions for the # 1120210 below.
    view full answer...

  • Mounting Bracket Needed To Install Superwinch LT2000 ATV Winch on 2005 Kawasaki 360 Prairie ATV
  • Yes, we have the mount you will need to install the Superwinch LT2000 ATV Winch, part # 1120210, on your 2005 Kawasaki 360 Prairie ATV. You will need to use the Superwinch ATV Winch Mount, part # 2202846. The Superwinch ATV Mount # 2202846 will fit both the 2x4 and 4x4 models of the 2005 Kawasaki 360 Prairie ATV. I have linked instructions for the Superwinch LT2000 ATV Winch, part # 1120210 and an FAQ on electric winches.
    view full answer...

  • Can a Superwinch Electric Winch be Used on a 1987 Kawasaki KLF 300 Bayou 2x4
  • The closest winch mount for a Kawasaki KLF 300 Bayou is for a 1989 model. There is no listing for a 1987. If your ATV has a 2 inch trailer hitch receiver, you could use the Portable Receiver Mount, # 1559B. The Superwinch Electric Winch, # 1120210, is designed to run off of a 12 volt system. If your Bayou uses a 12 volt system it can handle the power draw of the winch. However, if is a good idea to only power in/out the line in short increments of time so the system does not get overloaded. I
    view full answer...

  • How and Where To Mount Electrical Parts of Superwinch LT2000 Winch # 1120210 on 2006 Honda TRX 500
  • On the Superwinch LT2000 ATV Winch, part # 1120210, for your 2008 Honda TRX 500 Foreman Rubicon, the rocker switch is normally installed on the handle bar of the ATV. The black and green wires from the rocker switch will connect to the black and green wires on the solenoid. Using a circuit tester like the Quickee Tester, part # 3808, to test the wires on your ignition switch, you will need to find the wire that is powered only when the ignition switch is in the On position. The remaining red
    view full answer...

  • Superwinch Mounting Plate for Honda TRX 350 and TRX 450 for a Superwinch T1500
  • If you have a 2002 Honda TRX FourTrax 350 you would want a Superwinch ATV Winch Mount # 2202375. If you have a Honda TRX Fourtrax 450 you would want a Superwinch ATV Winch Mount # 2202381. Either of these hitch mounts would work well with a Superwinch # T1500 as they are both confirmed fits for this winch.
    view full answer...

  • Mounting Plate for a Superwinch 2500 for a 2009 Honda TRX 500 Foreman
  • For the 2009 Honda TRX 500 Foreman, Superwinch lists mounting plate # 2202898 as the correct fit. This mount will fit Superwinch models LT2000 (SW1120210), LT3000 (SW1130220), Terra 2500 (SW1125220), Terra 2500 SR (SW1125230), Terra 3500 (SW113522) and Terra 3500 SR (SW1135230).
    view full answer...

  • Finding the Hot Ignition Switch on a Kawasaki Prairie 700 ATV
  • If the wire you see on the ignition switch is a large wire, it may actually have other wires in side of it. What you can do is use a circuit tester like # 3808 if needed to locate the correct wire. The correct wire will only show power when the key is in the on position. You could also follow the wire to the starter motor and see if it separates out to 2 wires and test those wires. Bascially the only way to know for sure which wire to connect to would be to test the wires with a circuit test
    view full answer...

  • Winch Mounting Kit for a Superwinch LT20000 and a 2007 Honda TRX 420
  • The mount that you need for a 2007 Honda TRX 420 is # 2202889. It is also compatible with the Superwinch model # 1120210 that you have referenced. I have included a link to a video showing a typical installation for you.
    view full answer...

  • Availability of Winch Mounting Plate to Install Superwinch LT2000 on 2008 Honda TRX 420 Rancher ATV
  • The Superwinch # 2202889 would be the correct winch mount for your 2008 Honda TRX 420 Rancher 4x2. It is indeed compatible with the Superwinch LT2000 you mentioned. I have linked you to an install video showing the same winch being installed on a 2011 Rancher.
    view full answer...

  • Winch Mount for Superwinch LT2000 Electric Winch and a 2007 Yamaha Rhino 450 4x4
  • Yes, you can use the Superwinch LT200 winch, # 1120210, with your 2007 Yamaha Rhino 450 4x4. The proper mount for your ATV is # 2202908.
    view full answer...

  • Troubleshooting a LT2000 Superwinch that Feeds Out But Only Clicks When Set to Feed In
  • I spoke with my contact at Superwinch and he informed me that it sounds like you need a new relay for your LT2000 winch. Since you said you just bought the winch he said it should be covered under warranty and if you contact them they will send you a replacement. Here is their number 1-860-928-7787. He said the part you would need that would come everything needed is the Superwinch Upgrade kit for LT2000 Winches part # SW2320200. This will most like be what they send you.
    view full answer...

  • Superwinch LT2000 Winch Wiring and Installation on 2010 Polaris Sportsman 500 HO
  • I attached a set of the installation instructions and attached a picture that I pulled from them that shows where all of the wiring connections will need to made. I do not have specific written installation instructions for your 2010 Polaris 500 Sportsman but I did attach a video of this winch being installed on a very similar 2012 Polaris 500 Sportsman that will detail how we did it for that ATV. The process would be basically identical for you.
    view full answer...

  • Where to Install Solenoid and Circuit Breaker for Superwinch LT 2000 on a 2010 Polaris Sportsman 500
  • Typically, you will mount the solenoid and breaker under the seat where the battery is or on the frame in this same general area. I have included a link to a video showing a typical installation of Superwinch LT2000 on a 2012 Polaris that you can use as a guide.
    view full answer...

  • Troubleshooting Contactor/Solenoid on 12V Powered Winch
  • The direction of the winch operation, in or out, is determined by which of two solenoid contacts is connected to the 12V power input from the battery. If the winch operates only in one direction you can first try checking that all connections are solid and free from corrosion. Next you can do a bypass test to see whether the problem is in the switch or solenoid. Take a jumper wire from the battery +12V and touch it to the green wire on the solenoid. The winch should operate in one direction.
    view full answer...

  • Installation of the Remote for the Superwinch LT2000
  • For the Superwinch LT2000 ATV Winch # 1120210 we currently sell that winch kitted with the upgraded switch kit. This switch kit would attach to the handle bars on your ATV that you were using the winch on. If you are talking about the yellow hand held remote for the Superwinch LT2000 we do not sell that as a kit, but do have it available as a replacement part # SW87-12869. To wire up the yellow hand held remote you would route both the red and black wires from the winch to the remote, a
    view full answer...

  • Is there a Way to Lubricate Superwinch LT2000 ATV Winch
  • I spoke with my contact at Superwinch about the LT2000 winch, # 1120210. He said that the gears are pre-greased but to regrease them you could take the covering off of the winch to access the gears. Clean off all of the old grease and then use wheel bearing grease such as # L11380, to grease the gears. There are no fittings on the outside of the winch to grease the gears. None of the other parts need to be lubricated.
    view full answer...


Polaris 800 Sportsman Accessories


Info for this part was:


Expert Research:
Michael L

Video Edited:
Zack K

Video Edited:
Andrew K

Expert Research:
Robert G

Expert Research:
Michael H

Expert Research:
Jeff D

Expert Research:
Reno H

Expert Research:
Jameson C

Test Fit:
Nicholas E

Video by:
Andrew L

Expert Research:
Adam R

Expert Research:
Rachael H

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.





Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email



Only 7 Hours 53 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com