Call at 800-298-8924 for expert service. We are your Arctic Cat Winches experts, and offer a lowest price guarantee. carries a complete line of Superwinch products for your Arctic Cat Prowler 2007. Superwinch LT2000 ATV Winch, 2,000 lbs part 1120210 from Superwinch can be ordered online at Complete Winches installation instructions and technical support.
Select Your Vehicle

View Cart

Electric-Winch > 2007 > Arctic Cat > Prowler

Superwinch Winches for the Arctic Cat Prowler, 2007

Superwinch Winches

(8 reviews)

Code:   1120210



Shipping Special

Shipping Weight: 18.33 pounds


Superwinch LT2000 ATV Winch, 2,000 lbs - Arctic Cat Prowler, 2007

Superwinch LT2000 12v Winch

T-Series winches give you more value per dollar than anything on the market.

  • Powers Load IN and OUT
    • Includes freespooling clutch for fast wire rope payout
  • High efficiency low amp draw motor
  • Full-metal planetary gear-train
  • Sealed, handle-bar-mounted rocker switch
  • Dynamic brake
  • Circuit breaker protected
  • Includes Pulley Block, D-Shackle and Roller Fairlead
    • Fairlead requires mount kit (SW87-42616; sold separately)
  • Rated Line Pull (single line): 2,000 lbs.
  • Motor: 1.00 hp
  • Gearing: Differential Planetary
  • Gear Ratio: 153:1
  • Freespooling Clutch: Pull and Turn
  • Braking: Dynamic
  • Wire Rope: 5/32" x 49' with latched hook
  • Switching Method: protected relay
  • Dimensions: 11" long x 4.1" deep x 4.1" high
  • Warranty: 1 year
Recommended Accessories:
  • Accessory Kit with Leather Gloves (1554)
  • Mounting System for ATV

1120210 Superwinch ATV Recovery Winch

Replaces Model T2000 (# 1220200)

Video of Superwinch LT2000 ATV Winch, 2,000 lbs

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video Transcript for Superwinch LT2000 ATV Winch Installation - 2011 Honda Rancher

Today on our 2001 Honda Rancher were going to be installing the Superwinch LT2000 ATV Winch part number 1120210. Well also be using the ATV winch mount kit part number 2202889 designed specifically for the Honda Rancher. To begin our install were going to remove the black bumper cover from the ATV. You have the 2 bolts on the bottom of the bumper cover and on the top here are 2 pushpins. With our front bumper cover removed well go ahead and loosen up the lower cover which will allow it to flex like so. We can now take our bottom plates facer and our main plate 2/4 by 3/4 bolts and their nuts within the frame of the ATV here.

Well take the spacer block and place it in to take up the space within this frame. We can then take our main plate line up the holes that are already there with the frame and slide our bolt through. We can then put the nut on the other side and tighten it down. With our main plate attached to the frame here well install the U-bolts. Now that weve worked our U-bolts over the frame of the ATV we can put the nuts on the backside.

Alright, now were ready to go ahead and install our winch. Well need our spacer plate, 2 bolts supplied with the winch, washers, and a nut. Now, our winch will go in from the left side if youre sitting in the seat. You wanna make sure that the winch spools off of the top of the drum, thats how youll know that it is in correctly. Well take our spacer block and our bolt and feed it through our top mount and then put the winch through the bolt using our 2 washers, flat washer and the lock washer.

We can then install the nut and well repeat this process for the other mounting point of our winch. With our hardware loosely fitted well go ahead and install the smaller bolt, also included with the winch, into the remaining bolt hole of our bracket thats open just to kind of hold the spacer in place and with all our fasteners loosely fitted well go ahead and tighten them down with a wrench. And with that our winch is secured and we can move on to the Roller Fairlead. Now after gathering the hardware to install the Roller Fairlead well pre-assemble it before we mount it onto the vehicle. Youll notice that 2 round spacer within the tubes that surround the bolt.

These prevent the tubes from collapsing while youre tightening it down. Well now go ahead and feed it through the 2 holes in the main plate where we can put the nylon buts on the backside and tighten them down. And with our Fairlead now installed we need to get our cable through. Well go ahead and loosen up one of the horizontal rollers where we can slide the bolt out and remove our roller. We can then bring our cable up through the Fairlead and reinstall our roller. Now, you dont want to tighten the roller too much as it does need to roll to prevent the cable from binding or damaging. Well now go ahead and install the 2 lower bolts back into the lower steel plate that we took out earlier. Well go ahead and install this bolt here on the lower cover. When installing this bolt we do need to put in this extension which will allow us to attach the upper front bumper cover. Now, you wanna leave this bolt slightly loose so that your bracket can move around a little bit. While we install the upper cover well then go back and tighten it down later and well repeat the same process on installing the other bracket on the other side. Now, well need to locate a ignition source for our winch that will only allow the winch to work when the key is in the on position. Weve gone ahead and removed the light cluster from our four wheeler, located the ignition key wiring itself, found a wire that is only hot when the key is turned on and tapped into it. Now, we went ahead and found a location for our solenoid box and secured it to the frame. We then routed our wire along the frame following the factory wiring harness where we secured it to the body of the ATV and made our connections to our winch. We also went ahead and then connected our switch here at the green and black wires. Well go ahead and tuck those into the factory wire harness to give it a nice, clean look. Now we brought our battery wires up through again following the factory harness around to the battery. We connected our circuit breaker in line with our positive lead to our battery and taped it up so it doesnt have a chance of hitting anything metal and shorting out on us. We can simply tuck that out of the way and bring it around to our positive battery terminal where we will make our connection. Well then repeat that process for our ground side of our winch. Before you reassemble your four-wheeler you may wanna go ahead and turn your four-wheeler on and test the winchs operation. Our installation is complete, now we can go ahead and reinstall our front upper bumper and that will complete the Superwinch LT2000 ATV winch part number 1120210.

Customer Reviews

Superwinch LT2000 ATV Winch, 2,000 lbs - 1120210

Average Customer Rating:  4.4 out of 5 stars   (8 Customer Reviews)

- 1120210

by: Ed S.04/08/2014

I installed the Superwinch LT 2000 on a 2007 Honda Rancher and also the mounting kit # 2202889. The install went well. I had never put a winch on an ATV before. The video on etrailer was very helpful and would have been difficult to install without it. The instructions that come with the winch and the mount kit are minimal. I found the electrical wire length to be enough as I mounted the solenoid right behind the battery under the seat. The pink wire on the ignition was what I used to tap into to run the switch. 124317

- 1120210

by: Darrin K08/27/2014

Not impressed, was missing two bolts, two lock washers and two nuts. Had to go to the hardware store to get more. Instillation directions are a joke. I do not recommend. 148860

- 1120210

by: Eric E01/06/2015

your product 1120210 is very good, I have one on my 4 wheeler and am very satisfied with it. thank u for an affordable great product. 167931

- 1120210

by: TOM03/28/2013

Product as described. Great customer relations. Immediate shipment. Pleasure doing business with. Have placed an additional order. 73060

- 1120210

by: RB05/23/2014

Great product, great service, installed on 2014 polaris sportsman 132056

- 1120210

by: dan m08/08/2013

everything went well till wire and sole noid 93956

- 1220210

by: Roger B12/13/2012

Review from a similar Superwinch LT2000 in Winches

The best service I have ever had from any on line service with that extra thing called Civility . clean ,undamaged , Excellent service 61313


i like the 2000 super winch but i need to no if it comes with wiring and remote switch or do i need to get them here to let me know thank.s gene r

comment by: gene r - 01/02/2014


Wiring, circuit breaker and remote are all included with the winch. You may need additonal wiring if you are mounting it on the rear of a vehicle and you may need a mounting plate, but this will depend on the application.

Patrick B - 1/3/2014

- 1220210

by: Antonio C.06/30/2012

Review from a similar Superwinch LT2000 in Winches

Excellent product for that price 46306


Ask the Experts about this Superwinch Winches
Do you have a question about this Winche?

  • How and Where To Mount Electrical Parts of Superwinch LT2000 Winch # 1120210 on 2006 Honda TRX 500
  • On the Superwinch LT2000 ATV Winch, part # 1120210, for your 2008 Honda TRX 500 Foreman Rubicon, the rocker switch is normally installed on the handle bar of the ATV. The black and green wires from the rocker switch will connect to the black and green wires on the solenoid. Using a circuit tester like the Quickee Tester, part # 3808, to test the wires on your ignition switch, you will need to find the wire that is powered only when the ignition switch is in the On position. The remaining...
    view full answer...

  • Superwinch Mounting Plate for Honda TRX 350 and TRX 450 for a Superwinch T1500
  • If you have a 2002 Honda TRX FourTrax 350 you would want a Superwinch ATV Winch Mount # 2202375. If you have a Honda TRX Fourtrax 450 you would want a Superwinch ATV Winch Mount # 2202381. Either of these hitch mounts would work well with a Superwinch # T1500 as they are both confirmed fits for this winch.
    view full answer...

  • How to Wire SuperWinch LT2000 and Install On a 1997 Honda 300 4Trax
  • To connect the hot wire or Red wire of the Rocker Switch, you will connect it to the wire in the ignition switch that only is powered when the ignition is in the ON position. To determine which wire this is, you will need to use a circuit tester, item # 3808. If there is a headlight mounted between handlebars there is easily easy access to an ignition source inside headlight housing. Then, you will connect the Green wire on the rocker switch to the Green wire on the Solenoid. The Black...
    view full answer...

  • Troubleshooting Contactor/Solenoid on 12V Powered Winch
  • The direction of the winch operation, in or out, is determined by which of two solenoid contacts is connected to the 12V power input from the battery. If the winch operates only in one direction you can first try checking that all connections are solid and free from corrosion. Next you can do a bypass test to see whether the problem is in the switch or solenoid. Take a jumper wire from the battery +12V and touch it to the green wire on the solenoid. The winch should operate in one direction....
    view full answer...

  • Mounting Bracket Needed To Install Superwinch LT2000 ATV Winch on 2005 Kawasaki 360 Prairie ATV
  • Yes, we have the mount you will need to install the Superwinch LT2000 ATV Winch, part # 1120210, on your 2005 Kawasaki 360 Prairie ATV. You will need to use the Superwinch ATV Winch Mount, part # 2202846. The Superwinch ATV Mount # 2202846 will fit both the 2x4 and 4x4 models of the 2005 Kawasaki 360 Prairie ATV. I have linked instructions for the Superwinch LT2000 ATV Winch, part # 1120210 and an FAQ on electric winches.
    view full answer...

  • Will Superwinch LT 3000 Rub The Sides of the Tires on a Honda TRX 420 Whose Tires are 10 Inches Wide
  • The Superwinch ATV Winch Mount # 2202889 that you referenced is the correct mounting plate for the Superwinch LT 3000 that you are planning on mounting on your 2010 Honda TRX420. At this time, this is the only mounting bracket for the Superwinch winch on a Honda TRX 420. The space distance in question is from the mounting bracket to the side of your tire. I have two pictures attached that will assist you in determining if this winch will rub your tires. In the first picture I have...
    view full answer...

  • What is the Correct Winch Mounting Plate for the 2006 Polaris Sportsman 450 ATV
  • The item you selected Superwinch ATV Winch Custom Mounting Kit, part # 2202863, is the correct winch mount for the 2006 Polaris Sportsman 450 ATV. This winch mount is recommended for use with the Superwinch LT2000 ATV Winch, 2,000 lbs, item # 1120210, Superwinch Drum-Centric ATV2500 ATV Electric Recovery Winch, and the Superwinch Drum-Centric ATV3000 ATV Electric Recovery Winch.
    view full answer...

  • Superwinch LT2000 Winch Wiring and Installation on 2010 Polaris Sportsman 500 HO
  • I attached a set of the installation instructions and attached a picture that I pulled from them that shows where all of the wiring connections will need to made. I do not have specific written installation instructions for your 2010 Polaris 500 Sportsman but I did attach a video of this winch being installed on a very similar 2012 Polaris 500 Sportsman that will detail how we did it for that ATV. The process would be basically identical for you.
    view full answer...

  • Using Bumper Winch as Hoist
  • I would be very leery about using a bumper winch for this purpose. These winches are designed to pull, not lift. We offer a Crane Winch, part # 03002 that would work for this purpose, but it would need 12-volt DC power to work. I believe your best bet would be to find you a 110V electric hoist with sufficient capacity for the barrels and cases of soda.
    view full answer...

  • Is there a Winch Mounting Plate Available for the 2002 Honda Rancher that Fits Inside the Push Bar
  • I spoke with my contact at Superwinch and he sent me the instructions for the Superwinch ATV Winch Custom Mounting Kit, item # 2202375. In the instructions you can see that the winch will mount inside the front push bar and that the roller fairlead will be attached to the front of the winch mount and stick out just a bit. The mount for the roller plate is included with the # 1120210 ATV unit.
    view full answer...

  • Installation of the Remote for the Superwinch LT2000
  • For the Superwinch LT2000 ATV Winch # 1120210 we currently sell that winch kitted with the upgraded switch kit. This switch kit would attach to the handle bars on your ATV that you were using the winch on. If you are talking about the hand held remote for the Superwinch LT2000 we do not sell that as a kit, but do have it available as a replacement part # SW87-12869. To wire up the hand held remote you would route both the red and black wires from the winch to the remote, and from...
    view full answer...

  • Winch Mounting Kit for a Superwinch LT20000 and a 2007 Honda TRX 420
  • The mount that you need for a 2007 Honda TRX 420 is # 2202889. It is also compatible with the Superwinch model # 1120210 that you have referenced. I have included a link to a video showing a typical installation for you.
    view full answer...

  • Troubleshooting a LT2000 Superwinch that Feeds Out But Only Clicks When Set to Feed In
  • I spoke with my contact at Superwinch and he informed me that it sounds like you need a new relay for your LT2000 winch. Since you said you just bought the winch he said it should be covered under warranty and if you contact them they will send you a replacement. He said the part you would need that would come everything needed is the Superwinch Upgrade kit for LT2000 Winches part # SW2320200. This will most like be what they send you.
    view full answer...

  • Where to Install Solenoid and Circuit Breaker for Superwinch LT 2000 on a 2010 Polaris Sportsman 500
  • Typically, you will mount the solenoid and breaker under the seat where the battery is or on the frame in this same general area. I have included a link to a video showing a typical installation of Superwinch LT2000 on a 2012 Polaris that you can use as a guide.
    view full answer...

  • Can Superwinch LT2000 ATV Winch be Wired Using a Factory Fuse on a 2014 Polaris Sportsman 400
  • I strongly recommend using the circuit breaker since it will auto reset unlike a fuse that would blow and would have to be replaced. Also the winch # 1120210 was designed to be wired up using the circuit breaker and not for use with a fuse. I have linked the instructions and a video showing an installation of the winch for you.
    view full answer...

  • Will Superwinch LT2000 and Winch Mount # 2202889 Fit a 2012 Honda TRX 420 Recon
  • The Superwinch LT2000 # 1120210 and winch mount # 2202889 will both fit a 2012 Honda TRX 420 Recon. I have included instruction and video links for you to view.
    view full answer...

  • Superwinch Mount for a 2013 Honda TRX 420
  • Yes, I checked with Superwinch and they do list mounting kit # 2202889 as a fit for your 2013 Honda TRX 420. With this mount you can use Superwinch models LT2000 (SW1120210), LT3000 (SW1130220). The LT2000, # 1120210, is a popular option. I have included a link to a video showing a typical installation for you.
    view full answer...

  • How to Extend the Wiring of a LT200 Superwinch # 1120210 on a 2005 Yamaha Wolverine 350 FX
  • The best way to extend the wiring would be to get 10 Gauge Blue Primary Wire, part # 10-1-1, to extend the wiring and then use a 12-10 Gauge Butt Connector, part # 05732-2, to connect the wires. And then finally wrap the connection with Electrical Tape, part # BT66. That should give you the additional 12 inches you would need to connect your Superwinch LT2000 ATV Winch, part # 1120210, to your 2005 Yamaha Wolverine 350 FX. I attached installation instructions for the # 1120210 below.
    view full answer...

  • Winch Mount and Winch Recommendation for 2015 Honda FourTrax Foreman
  • For your 2015 Honda Foreman you can use Bulldog winch mount # BDW15181 and mating 2000-lb winch # 1120210 or 3000-lb model # SW1130220. These and other recovery winches that for this mount can be seen on the linked page. The two linked articles on winches may be of interest to you as you decide on your preferred winch model.
    view full answer...

  • Availability of Winch Mounting Plate to Install Superwinch LT2000 on 2008 Honda TRX 420 Rancher ATV
  • The Superwinch # 2202889 would be the correct winch mount for your 2008 Honda TRX 420 Rancher 4x2. It is indeed compatible with the Superwinch LT2000 you mentioned. I have linked you to an install video showing the same winch being installed on a 2011 Rancher.
    view full answer...

  • Finding the Hot Ignition Switch on a Kawasaki Prairie 700 ATV
  • If the wire you see on the ignition switch is a large wire, it may actually have other wires in side of it. What you can do is use a circuit tester like # 3808 if needed to locate the correct wire. The correct wire will only show power when the key is in the on position. You could also follow the wire to the starter motor and see if it separates out to 2 wires and test those wires. Bascially the only way to know for sure which wire to connect to would be to test the wires with a circuit...
    view full answer...

  • Where to Mount the Solenoid Box of the Superwinch LT2000 on a 2013 Polaris 550
  • Superwinch recommends that when you install the Superwinch LT2000 ATV Winch part # 1120210 on an ATV that you install the solenoid box close to the battery, in the storage box, under the seat or on the frame. It will be up to you to determine where of those locations would work the best for you. I would probably try in the area where the battery is first as that would probably be the easiest. I attached an installation video for this winch on a 2012 Polaris 500 which shows where they...
    view full answer...

  • Mounting Plate for a Superwinch 2500 for a 2009 Honda TRX 500 Foreman
  • For the 2009 Honda TRX 500 Foreman, Superwinch lists mounting plate # 2202898 as the correct fit. This mount will fit Superwinch models LT2000 (SW1120210), LT3000 (SW1130220), Terra 2500 (SW1125220), Terra 2500 SR (SW1125230), Terra 3500 (SW113522) and Terra 3500 SR (SW1135230).
    view full answer...

  • How Many Turns of the Handle Equal One Drum Revolution on Dutton-Lainson Winch DL24844
  • The gear ratio of winch # DL24844 would be 18.75 turns of the handle for one complete revolution of the drum. You could say that one revolution of the drum is 3-1/8 inches and that would be 288 turns of the handle for 4 feet. You might be able to adapt the wheel to the winch but it hasn't been tested with that type of apparatus so I cannot guarantee that it will work. And you are correct it would be less revolutions and easier to turn. There are other electric winches you could use....
    view full answer...

  • How To Wire Superwinch ATV Winch On 2000 Yamaha Wolverine 350
  • Per the installation instructions for the Superwinch LT2000 ATV Winch, part # 1120210, the red wire from the handlebar switch is to be connected to the wire on the ignition switch that only shows current when the ignition is in the on position. You can use a circuit tester like part # 3808 to be able to identify the correct wire. Then route the 2 long Black and Red wires from the solenoid to the motor. Next, route the shorter Black wire to the battery, and route the shorter Red wire...
    view full answer...

  • Switch Replacement for the Superwinch LT2000 ATV Winch # 1120210
  • The Replacement Rocker Switch # SW2233B that you referenced is the correct switch for your ATV 2000 lb winch # 1120210 so I would recommend it for you.
    view full answer...

  • Which Winch Will Work When Pulling a 950 Pound Boat Up a Trailer and Will Wiring Reach the Battery
  • The Superwinch LT2000 ATV Winch, # 1120210, has accessories more suited for ATVs, and the wiring included may not be long enough to reach the battery, let alone the cigarette lighter if mounted in the front. If mounted in the back it would really be a stretch. It does have a single line capacity of 2,000 pounds, so pulling a 950 pound boat should not be a problem. The matching winch for a vehicle is the Superwinch LT2000 Electric Utility Winch, # 1220210. It is essentially the same winch...
    view full answer...

  • My Winch Trips the Circuit Breaker and the Wires Heat Up After a Few Seconds of Use
  • It sounds like there is a short somewhere. That is what usually causes the breaker to trip and wires to heat up. The first step I would take is to inspect all of the wiring. Make sure there are no damaged sections of wires or contacts touching each other that should not be touching. The next step would be to determine which winch you have. The short could be internal, in the switch or winch, so we will want to determine which winch you actually have to see what replacements parts are...
    view full answer...

Do you have a question about this Winche?

Info for this part was:

Expert Research:
Michael L

Video Edited:
Zack K

Video Edited:
Andrew K

Expert Research:
Robert G

Expert Research:
Michael H

Expert Research:
Jeff D

Expert Research:
Reno H

Expert Research:
Jameson C

Test Fit:
Nicholas E

Video by:
Andrew L

Expert Research:
Adam R

Updated by:
Laura H

Expert Research:
Rachael H

Photos by:
Zach O

At we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.

Stay Connected

Subscribe to email newsletter


privacy - we don't send unsolicited email reviews

All images, layout and content copyright