Tekonsha Brake Controller with Wiring - 90195-3021P
- Features:
- Applies power to the trailer brakes in proportion to vehicle's deceleration.
- No level adjustment necessary - it adjusts itself to varying terrain as you drive.
- Works proportionally in reverse - great for backing into tough spots.
- Designed for use with electric over hydraulic trailer brake systems.
- Works equally well on standard electric trailer brakes.
- Digital display depicts voltage delivery to trailer during braking.
- Continual diagnostics check for proper connection, shorted magnet condition and much more.
- Easy to read and understand diagnostic display
- "Boost" feature gives users the ability to apply more initial trailer braking power when towing heavier trailers.
- Power-saving mode reduces drain on battery when vehicle is not in use.
- Unique pocket mount allows for flexible mounting options.
- Quick and easy disconnect feature allows user to remove and store the controller when not in use.
- Vehicle specific wiring adapter is included to make installation simple
- Storage pouch included to protect the P3 controller when stowed.
- Rotary style manual brake adjustment lever is easily accessible under the controller unit.
- Customize the LCD display by choosing language, color and contrast options.
- Language options: English, French, and Spanish
- Color options: blue, light blue, cyan, green, light green, orange, magenta, pink, and white
- Limited lifetime warranty
- Specs:
- Dimensions: 3-5/8" Wide x 4-5/8" Long x 1-3/8" High
- Boost levels increase power up 0%, 13% and 25%
- 180 degree vertical plane operating range
- Can be mounted between -90 degree (straight down) and 90 degree (straight up)
- Made for up to 4-axle trailer brake systems (2 to 8 Brakes)
- Diagnostic Troubleshooting displays: Battery Voltage, Stop Lamp Voltage, Output Voltage, Output Current
- Diagnostic Warning Signs: Open Ground, Overload, Output Shorted, Power Loss, and No Trailer Connected
- Installation:
The vehicle specific adapter has one end that plugs into the back of the brake controller while the other end plugs into the port located under the dash.
Note: If your vehicle has a factory installed hitch and 7-way connector, then all of the wires for the brake controller have already been run. If not, additional parts will be required to complete the installation of the brake controller.
Tekonsha P3 Electric Trailer Brake Controller with Dodge Adapter
The P3 controller is designed for use with electric and/or electric over hydraulic trailer braking systems. A simple switch on the unit allows the user to toggle back and forth between the two systems. The Tekonsha P3's LCD display features a distinctive look with multiple color and contrast options and includes a highly advanced, easy-to-understand roadside diagnostics display. The P3 advanced diagnostics not only notify you of potential problems, it can tell you where to begin trouble shooting.
Tekonsha P3 Brake Controller 90195 with Adapter 3021P
Ask the Experts about this Tekonsha Brake Controller with Wiring
- 2010 Dodge Trailer Brake Controller Wiring Adapter
- The Brake Controller Wiring Adapter, part # 3021-P is the correct adapter for the 2010 Dodge Ram. Dodge changed the connector for the 2010 model year. This adapter will work with the Tekonsha P-3 or the Prodigy Brake Controllers.
view full answer...
- Comparison of the Tekonsha P3 and P2 Brake Controllers for Use in a 2010 Dodge Ram 2500
- The major differences between the P2 brake controller, item # 90885 and the P3 brake controller, item # 90195, are that there is a 3 axis accelerometer in the P2 vs 1 axis in the P3. This means that the P2 has a greater range of mounting positions than the P3, which probably is not an issue in the 2010 Dodge truck. The P3 has more display capabilities and better fault detection.
Basically, the P2 is a bit easier to use for those who are towing the same trailer, with about the same load, consi
view full answer...
- Electric Trailer Brake Controller and Wiring Harness for a 2009 Dodge Ram 1500
- Since your 2009 Dodge Ram has a factory tow package (which should include a 7-Way trailer connector), you ill need Tekonsha P3 and Wiring Harness, # 90195-3020P. I you will need to do is mount the controller as specified in the instructions which I have linked for you, plug the wiring harness into the back of the brake controller and the other end into the under dash hook up you mentioned and installation will be complete.
I have also included a link to a video showing an installation on a 20
view full answer...
- P3 Brake Controller Recommendation 2011 Dodge Ram w Elec Over Hydra Brakes and Factory Controller
- To use a trailer with electric over hydraulic brakes on your 2011 Dodge Ram with an integrated brake controller, you will need to install an aftermarket brake control.
To install an aftermarket brake control you will have to disconnect the ITBM, this will turn on a warning lamp, on the instrument cluster. In order to disconnect the ITBM and not get the warning lamp, your local Dodge dealer will have to reconfigure the TIPM (Totally Integrated Power Module), of the truck. Once the TIPM has be
view full answer...
- Can an Aftermarket Brake Controller be Installed on a 2010 Dodge Ram with Factory Brake Controller
- You will be able to use the Tekonsha P3 Brake Controller and Wiring Harness, # 90195-3021P, on your 2010 Dodge Ram with factory integrated brake controller. But there are some things you will need to do in order to complete the installation.
First, you will need to visit a local Dodge Dealership and have them remove the sales code (XHC). The TIPM (Totally Integrated Power Module) will need to be reconfigured. Once the sales code has been disabled you can disconnect the ITBM electrical connect
view full answer...
Installation Details
