# 1
Hollywood Racks SR1 2-Bike Carrier - Spare Tire Mount
This HRSR1 bike carrier will not fit a 2023 Jeep Wrangler JL UNLESS you remove the stock Liddy Light and associated bracket. Upon discovering this, I was able to locate an aftermarket kit which allows for the relocation of the light to just above the rear camera. The kit was easily installed and the bike mount was installed just as easily as the directions explain. The new location of the light is partially obscured with the bikes mounted and, although not ideal, it is adequate and certainly better than total removal. I was unable to find any mention of this situation in the install instructions or reviews prior to purchase of the rack. I just wish I had been aware of this before purchase. I would have rated 5 stars for this product were it not for the slight hiccup. Kudos to etrailer. It is always a pleasure to do business with them. They are very helpful, friendly and knowledgeable.
When I purchased this rack it specifically said it would fit on a FJ Cruiser factory equipment tire. The rack does accommodate the width but not the height (P265/70R17) so the (U) section of the rack is not long enough to come in contact with the lower part of the tire. This makes the rack unexceptional the carry bikes on the tire do to the lack of support! The rack itself is well constructed and would be excellent on a smaller tire. I modified this rack so it would contact the tire in two places, this works great and just returned from a 4,000 mile trip and could not be happier. Easy to put on, rock solid ride, though my bike frames are small tube and I used a small piece of split garden hose to take the slop out of the rubber frame cradles.
# 2
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
Hitch pin broke before I got it. Looks like a poor design for the locking pin, they might want to consider a different design. I got a 3/8 shear pin from Home Depot to replace and it works great. Bike rack is great!
# 3
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
I own a 2005 Jeep Wrangler X with 31x10.5x15 oversized tires and wheels. I installed B6196001 HighRock 4x4 Oversize Tire Carrier by Bestop to carry larger spare tire. I needed a bike carrier that would carry our two crusier bikes and clear my spare tire. After measuring, I ordered: -> S64650 - Swagman 2-bike carrier -> 80300 - 7" Hitch Adapter 2" to 1-1/4" Trailer Hitch Receiver -> RM-061 - Roadmaster Quiet Hitch for 2" Trailer Hitches Our order arrived very quickly, etrailer.com upgraded the shipping. All these products arrived well packaged and without damage. In 15 minutes I had every thing assembled, installed on my Jeep and bikes loaded. The bike carrier is very well constructed, finish is excellent and easy to adjust. When adjusting wheel loops and loading bikes, make sure you pay attention to bike pedal position. I chose this extension because I did not want to use the adapter that comes with the bike carrier, I wanted as few parts as possible to keep rattles to a minimum and gives me more options for towing. The anti-rattle bolt/pin firmly secures the bike carrier to the extension and the Roadmaster Quiet Hitch keeps the extension adapter from rattling in the receiver. Road tested approximately 25 miles over rough city roads ( including railroad tracks ), county roads and highway. Bikes traveled very well without any rattles. I can remove my complete setup quickly, fold and put in rear of Jeep if desired. I am very well pleased with my purchase. Note to etrailer: Please consider offering Roadmaster Quiet Hitch in black to match receiver and accessories. Paul In the Land of Oz . . . Just South of the Yellow Brick Road!
# 4
SportRack Ridge Swing 4 Bike Rack - 2" Hitches - Swinging
Unit doesn't fit a Jeep Rubicon with a spare tire. I tried 4 times and contacted etrailer.com that the unit doesn't work as sold and they offered to sell me a 7 3/4 extension and reduce the load capacity 50%. The length of the 2" hitch needs to be 3" longer for a standard Rubicon to get past the spare. You not going to want to take your spare tire off for the hitch to work. It defeats the purpose. Customer service was excellent, however the product is a flawed design. Can't recommend this hitch. Its also heavy.
Solid rack for half the price of the name brands. Don’t waste your money! Thanks to the extensive reviews on etrailer and a free shipping promotion I took a chance and ordered this along with the three of their crossbars, anti rattle hitch pin and cable lock. All for well less than the name brand rack alone. Shipping was painful. Etrailer said it was in stock but then due to a delay with the manufacturer it took 35 days from order to arrival. I wasn’t in a hurry so I waited patiently, and etrailer reps emailed often to lmk they hadn’t forgotten. I thought some kind of reward for my extreme patience was in order- discount, gift card, free bag of chips- but they politely declined. Oh well. In the end it arrived when they (eventually) said it would, all in one box, in great shape. The rack was super easy to assemble. You’ll need a ratchet or two and you’ll need to crank those bolts to assemble- they don’t just “insert.” But otherwise it’s only a few steps; I had mine hanging on my truck in probably 15 minutes. Swings away and locks smoothly and requires no effort to do so. Everything feels quite sturdy and well made. No rattle on initial test drive either. This will be a once in a while rack at best for our family of four. We have two SUVs so I needed a rack that could get out of the way of the rear hatch WITH bikes on it. This will do that. And now I don’t need to stuff four dirty bikes into the back of my truck, getting them all tangled and scratched!
# 5
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
What our customers are saying:
"I ordered a trailer hitch and a bike rack carrier the order was shipped with in three days. To put the hitch on only took about 30 mins. only had to drill two 1/2 holes. fit like a glove."