# 1
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 2
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Excellent customer service & support! Bought for my 2013 Honda Fit and plan to trailer my Yamaha Tenere motorcycle around North America! Very happy with hitch.
Typical quality of...VERY good!! Lol. I've pulled my small mc trailer numerous times with this hitch and NO issues!!!
# 3
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 4
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 5
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
It isbthe right size and helps with the height difference to make the trailer more even with the back end of my Accord.
Look and quality of the mount is awesome. Beefy in size as well. If using on my particular application, removal of rear diffuser is necessary. If they had extended it another inch it woulda been perfect. 2015 Audi a3 tdi. Wouldn’t let me add a third pic but it’s a finger tip space between the ball and bumper with diffuser removed.
# 6
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
# 7
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.
# 8
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 9
Curt Drawbar for 1-1/4" Hitches - 5-3/8" Rise, 6" Drop - 5-9/16" Long - 2K
I used this on a 2014 Ford Fusion with a Reese receiver hitch made for my vehicle. Either the neck of the drop hitch is not long enough to get the ball a few inches away from the vehicle or the Reese receiver hitch sits too far under the vehicle.
Website was easy to use and order. Tracking the package was simple to follow and package arrived on schedule. Part works great
# 10
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 4-5/8" Rise - 3,500 lbs
Perfect for my Honda Fit as it has a low carriage, the Euro shape gave me a few extra inches to tow a small trailer across the country from Oregon to North Carolina with no issues.
Love this hitch. It looks and fits my Optima perfectly. I was really pleased to find a modern looking hitch to fit on my car. Very strong, solid construction. I don't plan to pull a large trailer with my car but this will work perfectly for my utility trailer. Very friendly and helpful customer service and it was delivered faster than I hoped for. Extremely pleased. Thanks...
# 11
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 12
Curt Class II Euro Style Drawbar with 2" Ball - 3-1/8" Rise - 3,500 lbs
Incorrectly listed on etrailers as a 3-1/8” rise, when really this is a 5-1/8” rise (marked correctly on the item itself, but listed incorrectly on this website).
I am completely satisfied with the product. Great quality and excellent finish. Prompt shipping and excellent customer service. It is stylish and functional and will meet my needs for towing up to 3,500 pounds. I would definitely do business with this company again!!!
# 13
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
# 14
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 15
Curt Class I Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 2,000 lbs
I have a 2022 VW ID.4 AWD with factory installed receiver. This drawbar is 1/4" longer than VW recommends, but in rise orientation the length is required to clear the bumper. I ordered a shorter Curt drawbar but found it could not be installed in rise orientation because it hits the bumper before the pin hole is aligned. Both the shorter and this Curt drawbar fit fine in drop position, but were very tight in rise. I had to sand down the paint and file the corners to make the Curt fit easily so that it could be inserted and removed from the receiver by hand. I can't say whether this is a VW or Curt issue.
I highly recommend etrailer hitch and wiring harness They were both easy to install. The Prius pull the motorcycle camping trailer very well. You would not even know it was hooked to the car
# 16
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 2-3/4" Rise - 3,500 lbs
Very nice product! Appears like the European models. That is what I was looking to obtain. Will be used for show on my 1957 Triumph TR3.
100's of miles on it and all is well.
# 17
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 18
Rapid Hitch Adjustable Aluminum Ball Mount Kit - 2 Zinc Balls - 4" Drop or Rise
What do i like about this hitch…i tow trailers requiring both size balls andmits easy to flip this around and adjust tow height. Its lightweight and easy to take on and off when needed. The built in locks keep the hitch on my truck. I like it and recommend it.
I purchased this to replace a Fastway Flash E Series Ball mount that I purchased and returned from another online seller that did not provide enough clearance from my rear bumper in the rise position. My vehicle really needed the extra 5/8ths of an inch of length on the shank of the Rapid Hitch. Clearance was not a problem in the drop position; but with a receiver that's 18-inches off the ground, I need to use the rise position more frequently than many. The other thing I noticed is that this ball mount is feels more substantial than the one from Fastway. In use, I prefer this to the Andersen EZ hitch I had been borrowing. It looks really cool. It has 5 adjustment positions rather than four and bit more adjustability in either direction. Plus, it still fits in easily in the storage area underneath the floor of my SUV. And did I say it looks really cool. I hated to put grease on the ball before I went to hook up the trailer. Also, I plan to get the lock set. It's looks great on my SUV and seems likely to disappear overnight and look great on someone else's vehicle.
# 19
Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
Keep with spare tire out of weather to prevent rust.
Every Curt product we've purchased over the years has been perfect. Quality, fitment, price, etc has been spot on. The Curt products are far better made than Reese and Draw-Tite. Not even close!
# 20
Curt Class II Drawbar - 3-1/8" Rise - 9-1/2" Long - 3,500 lbs
Fits my Curt hitch as described (also purchased from eTrailer), but if pushed in too far it gets stuck in the receiver tube. Had to use a wheel puller to get it back out! Just need to push it in an inch or so to the pin holes line up not problem. My only complaint about ETrailer is that they use huge staples to close their shipping boxes. The staples are tough to pull out (get out your screw driver and pliers if you don't have an industrial strength commercial staple puller). My cardboard recycler does not want these dangerous looking staples left in the box, so I need to pull every one of them out!
Very fast delivery, Very low price for this sturdy drawbar... fits my Rav 4 Class II hitch perfectly.
What our customers are saying:
"I received this order yesterday. Thanks for the outstanding service. I appreciate it! Thanks, Alex"