Select Your Vehicle

View Cart

Best Nissan Xterra Bike Racks

change vehicle


Bike Rack Videos

SportRack Roof Mounted Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra we're going to be test fitting the Sport Rack Fork Mount Roof Bike Rack part number SR4622. With our Thule Rapid Crossroads Roof Rack already installed on our Xterra, we're going to begin our test fit by placing the bike rack directly onto our load bars. Here at the front of the carrier, we're going to bring the two black metal, rubber coated U-bolts around the underside of our load bars, fit them through the head of the carrier, and secure them in place using the wing nuts. With all four wing nuts here at the front tight, we'll move to the rear. Here we're going to take two carriage bolts, place them through the appropriate holes in the base of the rack, being sure that we have one coming out on each side of our load bar, we'll then take the black plastic spacer, place it between our load bar and our rack, being sure that our carriage bolts go through that, then we'll put on the black rubber coated metal portion of our clamp. This will go under our load bar, and we'll secure it in place using the two wing nuts. With these two wing nuts tight, our rack is secured to our vehicle and we're now ready to load our bike. We'll want to undo our rear wheel strap and open our front skewer. We'll then grab our bike, place it onto the rack, guiding the front forks down onto the skewer where we'll secure it first ...



Kuat TRIO Roof Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we're going to be test fitting the Kuat Trio, a fork-mounted roof bike rack, part number Ru01. With our Tuley Rapid Crossroads Roof Rack System already installed on the Xterra, we're going to begin our test fit by placing the trio directly onto our load bars. At the front of the carrier, we'll bring one of the black, rubber-coated metal U-bolts around the underside of our load bar, fit it through the head of our carrier, and hold it in place using two of the cylinder nuts. On the other side of the front of the carrier, we'll do the same thing. Bring the U-bolt around the underside of the bar, put on the two cylinder nuts; then we can tighten all four of our cylinder nuts down, to secure the rack to the vehicle, here at the front. We'll now move to the rear, where we're going to loosen our clamp and remove one of our wing nuts completely.



Yakima HoldUp 2 Hitch Bike Rack Review - 2013 Nissan Xterra

Today, on our 2013 Nissan Xterra, we'll be test fitting the Yakima Hold Up two bike carrier, platform style part number y02443. To begin our test fit, well slide the shank of the carrier into the received tip of our hitch. Line up the pinhole and thread in our anti-rattle bolt tightening with a wrench and securing with the lock on the other side.Now, well go over some key measurements. We have about 23 inches of ground clearance. The closest point of the carrier to the rear of the vehicle is about eight inches. Weve added 14 inches to the overall length of our Nissan Xterra.



Yakima StickUp 2 Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra well be test fitting the Yakima Stickup Two Bike Hitch Mounted Bike Carrier, part number y02420.To begin our test fit well slide the shank of the carrier into the receiver tube of our hitch, line up the pin hole and thread in our anti-rattle bolt tightening it with a wrench. Now well go over some key measurements. We have about 18 inches of ground clearance. The closest point of the carrier to the rear of our Xterra is about 7 inches. Weve added 15 inches to the overall length of our vehicle. Well go ahead and pull the red knob here at the base of the mass to unfold our carrier.



Yakima HighLite 2 Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra well be test fitting the Yakima Highlite Aluminum Two-Bike Carrier, part number 702438.To begin our test fit well slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole and install our pin with the red knob. Well move to the rear of the shank and use the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device.Now well go over some key measurements. We have 17 inches of ground clearance. The closest point of the carrier to the rear of our Xterra is about 8 inches. Weve added 13 inches to the overall length of our Nissan Xterra. Well pull the pin with the red knob at the base of our mass to allow our carrier to tilt away from our vehicle.



Yakima DoubleDown Ace Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra well be test fitting the Yakima Doubledown Ace Four Bike Carrier, part number y02451.To begin our test fit well slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole and install the attached pin with the red knob. Well move to the rear of the shank and use the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over some key measurements. We have 17 inches of ground clearance. The closest point of the carrier to the rear of the vehicle is 8 inches. Weve added 14 inches to the overall length of our Nissan Xterra.



Yakima DoubleDown Ace 2 Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra we'll be test fitting the Yakima Doubledown Ace Two Bike Carrier, part number y02450. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and install the attached pin with the red knob. We'll move to the rear of the shank and use the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device.Now we'll go over some key measurements. We have 17 inches of ground clearance. The closest point of the carrier to the rear of our Xterra is about eight and a half inches.



Thule Vertex 4 Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we will be test fitting the Thule Vertex 4 Bike Carrier, part number TH9029. To begin our test fit, we will slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole, and thread in our anti-rattle bolt, tightening it with a wrench. Now we will go over some key measurements. We have about 18 inches of ground clearance. The closest point of the carrier to the rear of the vehicle is about 5 inches.



Thule T2 Platform Style Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Thule T2 Platform Style 2-Bike Carrier, part number TH916XTR. To begin our test fit, we'll slide the shank of the carrier into the receiver tip of our hitch, line up the pinhole and thread in our anti-rattle bolt, tightening it with a wrench.Now we'll go over some key measurements. We have about 17 inches of ground clearance. The closest point of the carrier to the rear of our Xterra is about 5 inches. We've added 16 inches to the overall length of our Nissan Xterra. We'll now pull the grey lever at the base of the carrier, to allow our carrier to unfold.



Thule Hitching Post Pro Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Thule Hitching Post Pro Folding, Titling 4-Bike Rack with anti-sway, part number TH934XTR. To begin our test fit, we'll slide the shank of the carrier into the receiver tip of our hitch, line up the pinhole and thread in our anti-rattle bolt, tightening it with a wrench.Now we'll go over some key measurements. We have about 17 inches of ground clearance. The closest point of the carrier to the rear of the Xterra is about 10 inches. We've added about 20 inches to the overall length of our Nissan Xterra. We'll pull the pin at the base of the carrier, to allow our carrier to tilt away from the vehicle.



Thule Helium Aero Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Thule Helium Aero 2-Bike Carrier, part number TH9042. To begin our test fit, we'll slide the shank of the carrier into the receiver tip of our hitch, allowing the included and attached pin to fall into position. Then we'll move to the rear of the shank and use the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device.Now we'll go over some key measurements. We have about 21 inches of ground clearance. The closest point of the carrier to the rear of our Xterra is about 7 inches. We've added 21 inches to the overall length of the Nissan Xterra.



Thule Doubletrack Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Thule Doubletrack platform-style 2-bike carrier, part number TH990XT. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of our hitch, line up the pin hole, and thread in our anti-rattle bolt, tightening it with a wrench. Now we'll go over some key measurements. We have about 16-1/2" of ground clearance. The closest point of the carrier to the rear of our Xterra is about 7". And we've added 14" to the overall length of our Nissan Xterra.



Thule Domestique Roof Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Thule Domestique fork-mounted bike carrier, part number TH513. Now to begin our test fit, we'll go ahead and place the carrier on top of our crossbars. We'll then make sure that the head of the bike rack is directly over the front crossbar. We'll take the clamp, put it underneath the crossbar, where we'll use the included Allen bolts and wrench to secure it in place. With our head secured, we'll go ahead and move to the rear mounting location where we'll use the Allen bolt and the Allen wrench to secure it to our rear crossbar. Now with the bike rack secured to our Xterra, we're ready to load our bike.



Thule Circuit Roof Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan XTerra well be test fitting the Thule Circuit Roof-Mounted Bike Carrier part# th526. With our roof rack system already assembled onto our vehicle, well place our carrier directly on top of our load bars. Once we have our carrier in place, well lift up the nose lever at the front of the carrier and hand tighten the wing nut. Once we get the wing nut snug we can then close the nose lever to finish securing the front part of our carrier. At the rear, we just need to make sure that the clamp is around a load bar and then feed the bolt through the wing nut and tighten. Well now go ahead and reinstall our skewer. Well leave our skewer open and then well move to the rear and undo the rear wheel strap. Well grab our bike, place the rear wheel into the wheel cradle, and drop the front forks down into the skewer. Well secure the bike first by tightening our skewer and then well move to the rear and secure it by tightening the wheel strap.With that our bike is all loaded up and were ready to hit the road.



Thule Apex 4 Swing Hitch Bike Rack Review - 2013 Nissan Xterra

Today on 2013 Nissan XTerra well be test fitting the Thule Apex Swing four-bike carrier part# th9025. To begin our test fit well slide the shank of the carrier into the receiver tube of the hitch allowing the included and attached pin to fall into position. Well then move to the rear of the shank and use the hand-knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over some key measurements. We have about 17 inches of ground clearance. The closet point of the carrier to the rear of our XTerra is about four inches. Weve added about 15 inches to the overall length of our Nissan XTerra. Well pull the lever at the bass of the mast to swing out or dual arms.



Thule Apex 4 Hitch Bike Rack Review - 2013 Nissan Xterra

Today on 2013 Nissan XTerra well be test fitting the Thule Apex four-bike carrier part# th9025. To begin our test fit well slide the shank of the carrier into the receiver tube of the hitch allowing the included and attached pin to fall into place. Well then move to the rear of the shank and use the hand-knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over some key measurements. We have about 18 inches of ground clearance. The closet point of the carrier to the rear of our XTerra is about four inches. Weve added about 15 inches to the overall length of our Nissan XTerra. Well pull the lever at the bass of the mast to allow our carrier to tilt away from our vehicle.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Swagman XTC2 2-bike platform carrier, part number S64670. To begin our test fit, we'll slide the shank of the carrier into the receiver tube of our hitch, line up the pin hole, and thread in our anti-rattle bolt, tightening it with a wrench. Now we'll go ahead and go over a few key measurements. We have 21" of ground clearance. The closest point of the carrier to the rear of the Xterra is about 9". And we've added 24" to the overall length of our Nissan Xterra.



Swagman Titan Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan XTerra well be test fitting the Swagman Titan four-bike carrier part# s63410. To begin our test fit well slide the shank of the carrier into the receiver tube of our hitch. Line up the pinhole and thread in our anti-rattle bolt tightening it with a wrench. Now well go over some key measurements. We have about 20 inches of ground clearance. The closes point of the carrier to the rear of our XTerra is 10 inches. Weve added 23 inches to the overall length of our Nissan XTerra. Well pull the pin at the base of the mast to allow or carrier to tilt away from the vehicle.



Swagman Fork Down Roof Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan XTerra well be test fitting the fork-style roof-mounted bike rack from Swagman part #s64710. With our roof-rack system already installed onto our vehicle, well place our bike carrier directly onto our crossbars. To secure the front part of our carrier well feed the U-bolts underneath our crossbar and up through the holes in the platform. Well secure the front part of our carrier by installing wing nuts on each U-bolt and tightening them down. Well move to the rear. Well feed the U-bolt through the top of the carrier making sure that it goes around the crossbar. Well install the wing nuts and tighten them down securing the rear part of our bike carrier. Now we need to make sure that the skewer is open and that the rear wheel strap is undone. Well grab our bike; place it onto the carrier dropping the front forks down onto the skewer.



Softride Dura Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra we're going to be test fitting the Softride Dura Parallelogram Tilting Four Bike Rack for 1-1/4 and 2 Inch Hitches, part number sr26247. To begin our test fit we'll slide the shank of the carrier into the receiver tube of our hitch. Line up the pin hole and thread in our anti-rattle bolt, tightening it with a wrench and then installing the lock.Now we'll go over some key measurements. We have about 17-1/4 inches of ground clearance. The closest point of the carrier to the rear of our Xterra is about five inches. We've added 29 inches to the overall length of our Nissan Xterra.



Rola TX-104 Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra well be test fitting the Rola TX-104 Four Bike Carrier for two inch hitches, part number 59401.To begin our test fit, well slide the shank of the carrier into the receiver tube of our hitch. Line up the pin hole, thread in our anti-rattle bolt, tighten it with a wrenchand install the clip on the other side. Now, well go over some key measurements. We have 17 inches of ground clearance. The closest point of the carrier to the rear of our Xterra is nine inches.Weve added 15 inches to the overall length of our vehicle. Well pull the pin at the base of the carrier and lift it up on the mast to allow our carrier to tilt away from the vehicle.



RockyMounts TieRod Stretch Roof Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra we'll be test fitting the RockyMounts TieRod Stretch Roof Mounted Bike Carrier, part number rky1011. Now to begin our test fit we'll place the bike rack on top of our crossbars. We'll make sure that the head of the bike rack is over the front crossbar where we'll bring the rubber-coated steel straps underneath the crossbar and secure it back to the head of the bike rack.With that done we'll take the large Allen wrench that comes with the TieRod Stretch and tighten down the bolt here in the center. This will bring the rubber-coated steel straps tight securing the head of the bike rack to the front crossbar. We'll move back to the rear crossbar where we'll make sure that the rear mounting point is slid through the rear crossbar and tighten it down using the smaller Allen wrench that also comes with the TieRod.Now that we have all our bolts tight our bike rack is secured and we're ready to load our bike. We'll make sure that the front fork skewer is undone as well as the rear wheel strap out of the way.



Rhino-Rack 4 Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra we'll be test fitting the Rhino Rack Four Bike Carrier for 2 Inch Hitches, part number rbc038. To begin our test fit we'll slide the shank of the carrier into the receiver tube of the hitch. Line up the pin hole and thread in our anti-rattle bolt tightening it with a wrench and installing our lock.Now we'll go ahead and go over some key measurements. We have a ground clearance of 21 inches. The closest point of the carrier to the rear of our Xterra is about 8-1/2 inches. We added 15-1/2 inches to the overall length of our Nissan Xterra.



Prorack 2 Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Prorack 2-Bike Carrier, part number PR8062403.To begin our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pinhole, and thread in our anti-rattle bolt, tightening it with a wrench, and installing the clip on the other side.Now we'll go over some key measurements. We have 17" of ground clearance. The closest point of the carrier to the rear of the Xterra is about 6". We've added 27" to the overall length of our Nissan Xterra.We'll pull the pin at the base of the carrier to allow our carrier to tilt away from the vehicle. This allows us to gain access to the cargo area of our Nissan Xterra by opening our rear hatch.With our mast back in its upright position and our pin reinstalled, we can undo the cradle straps to expose our cradles. We'll place our bike onto the frame cradles and secure it by tightening down each strap.Now our bike's all loaded up, and we're ready to go.That completes todays test fit of the Prorack 2-Bike Carrier, part number PR8062403, on our 2013 Nissan Xterra..



Pro Series Q-Slot 2 and 4 Bike Hitch Bike Rack Review - 2013 Nissan Xterra

Today on our 2013 Nissan Xterra, we'll be test fitting the Pro-Series Q-Slot platform-style bike rack, part number PS63138. This bike rack can be configured to carry two or four bikes. We will be test-fitting ours in the two-bike configuration.To begin our test fit, we'll slide the shank of the carrier into the receiver tube of our hitch, line up the pinhole, and thread in our anti-rattle bolt, tightening it with a wrench.Now we'll go over some key measurements. We have about 18" of ground clearance. The closest point of the carrier to the rear of the Xterra is about 12". We've added 27" to the overall length of our vehicle.We'll go ahead and pull the pins at the base of the carrier to allow it to unfold.





Nissan Xterra Bike Rack Questions

  • I went out to our demo area to measure the height of the Saris Freedom # S4026 when it is folded up. From the tops of the shank to the top of the crossbar it is approximately 24 inches. From there it is another 6 inches to the wheel cradles.
    view full answer...

  • I went to our warehouse and took some measurements for you. I have attached a photo of the Kuat Bike Rack, part # N105-107 that shows the dimensions you asked about. As you can see, there is very little room for between the arms and posts to allow the camera view to be clear. The Thule bike carrier, part # TH916XTR-918XTR has similar dimensions, and would certainly obstruct part if not all of the camera view. Due to the bit of flexibility in the arms there will be some variation...
    view full answer...

  • I checked with Thule and yes, the Thule Raceway 2 Bike Rack # TH9001PRO that you referenced will fit your 2013 Nissan Xterra. If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may also be interested in purchasing a Thule Bike Adapter Bar # TH982XT to provide a horizontal top tube on your bikes to provide an attachment point. I attached a review video for this product also. This will allow the bikes to be carried more level and will...
    view full answer...

  • There are platform style bike racks that hold the bikes at the wheel and/or frame that can accommodate alternative frame styles like the ones you have mentioned. However none of those are available in a swinging style. If you are set on a swinging bike rack then you will need adapters to carry those bikes. For a swinging rack I recommend the Thule Vertex, # TH9031XT. It will offer the most clearance from the hitch pin hole to the back of the upright bar, 14 inches, 8-1/2 to...
    view full answer...

  • For your 2011 Nissan Xterra with a 2 inch hitch you could get a Thule Vertex 2 Bike Carrier # TH9028XT like you referenced. This is a quality rack that has anti-sway cradles, a locking anti-rattle device and a tilt feature to allow access to the rear cargo area. I attached a review video for you to check out. The most popular bike rack among 2011 Nissan Xterra owners that we sell is the Thule T2 Platform Rack # TH916XTR. This is a platform rack that allows the bikes to sit...
    view full answer...

  • The Thule Big Mouth Roof Mounted Bike Rack # TH599XTR that you referenced is a frame-clamp type rack intended for installation on round or square roof rack crossbars. Its wheel hoop straps require some space under the carrier, which would be available when mounted on roof rack crossbars, but not when installed to a trailer deck. However, we do have other options that are better suited to your requirements. If you need a rack you can use while towing a flatbed trailer with your...
    view full answer...

  • I would recommend going with the Hollywood Racks Sport Rider, # HR1000, for your Day 6 DreamE electric bicycle, as long as the wheel base on the DreamE is not longer than 60 inches. I did a bit of research and could not come up with a definite number for your bikes wheel base, but I believe it is somewhere around 51 or 52 inches. When using this rack you will need to remove the battery because the rack is rated for 2 bikes at 50 lbs each. This is the only rack we carry at this...
    view full answer...

  • The Swagman XTC4 bike rack, part # S64665, should work on a front mounted hitch, but there would be a few deciding factors. First, the XTC4 does have a shipping weight of 66 pounds, so you would need to make sure that the weight of the bike rack, plus the weight of the bikes you will carry will not exceed the tongue weight rating of the front hitch. Second, you would need to make sure that your bikes will not interfere with your vision when driving. The XTC4 has a raised...
    view full answer...

  • We have the Curt Multipurpose Ball Mount with 2 inch Receiver for Bike Racks and Cargo Carriers, # D210. This draw bar has a 12-1/2 inch length from the center of the hitch pin hole to the center of the ball hole. It measures 7-1/2 inches from the center of the hitch pin hole to the center of the top receivers hitch pin hole. The ball mount portion has a 2-1/4 inch drop. The receiver has a 6 inch rise. The entire unit rated for 7500 pounds gross trailer weight and 750 pounds tongue...
    view full answer...

  • We have several trunk mount bike racks that will fit your 2007 Nissan Xterra. I have included a link to the options for you. My favorite for 2 bikes is the Raceway # TH9001PRO that you have referenced and my favorite 3 bike rack is the Raceway 3 # TH9002PRO. I own the Raceway 3 and it is the best trunk mount rack I have used. The Raceway bike racks feature an integrated cable lock in the last bike position and the cables can be locked into position on one side to deter theft....
    view full answer...

  • Most 1-1/4 inch ball mounts are solid rather than hallow and this bike rack # S64095 is designed to accept a ball with a 3/4 inch diameter shank like # 19256. This ball and a 3/4 inch diameter shank are what you would see on a 1-1/4 inch hitch so you really have nothing to worry about as far as compatibility. The warranty issue is something else entirely. Swagman makes the following statements in the instructions which I have linked for you: 1. Purchaser is advised that...
    view full answer...

  • There are a couple trunk mounted bike racks that will work on your 2004 Nissan Xterra, but the Yakima SuperJoe Pro 3 # Y02630 that you referenced will not work. The Yakima KingJoe Pro 3 Bike Trunk Mounted Bike Rack # Y02625 and the Yakima KingJoe Pro 2 Bike Trunk Mounted Rack # Y02624 are both confirmed fits for your vehicle. I attached installation instructions for both of these racks for you to check out. If you plan on carrying womens or alternative framed bikes you...
    view full answer...

  • You would need 1 adapter bar per bike if you plan on carrying women's bikes on a hanging style bike carrier such as the Apex, # TH9026. the other option is to use the Softride Hang5, # SR26496, which also has a 5-bike capacity but it holds them vertically. On the Apex, the cable lock really only needs to be able to lock the last bike because if it is secured with the lock you would not be able to remove any of the other bikes. On the Hang5 you would need to add a cable lock...
    view full answer...

  • Yakima does not test-fit their Prorack line of racks to specific vehicles, but because the Prorack 2 bike rack is so similar to the Yakima SuperJoe, we can infer that if the SuperJoe will fit a given vehicle, the Prorack rack will as well. Because the SuperJoe will not fit your Xterra, it is extremely likely that the Prorack rack will not fit either. The most similar bike rack that will work for you at a fairly comparable price would be the Thule Passage, part # TH910XT. Despite...
    view full answer...

  • Yes, I checked with Yakima and the Yakima KingJoe Pro 3 Bike Rack # Y02625 that you referenced has been confirmed to fit your 2004 Nissan Xterra so it would work well for you. Check out the review video I attached for more info. If you plan on carrying any womens or alternative framed bikes without horizontal top tubes you may also be interested in purchasing a Swagman Easy-Out Women's and Alternative Frame Bike Adapter # 64005 to provide a horizontal top tube on your bikes...
    view full answer...

  • We have trunk mounted bike racks that will fit on your 2003 Nissan Xterra, but I would not recommend using the Prorack 2 Bike Rack, # PR8062401, on your vehicle. Prorack does not provide vehicle specific fit information for their bike racks, but I can tell you that Prorack is manufactured by Yakima and Prorack's 2-bike rack is very similar to the Yakima SuperJoe bike racks which do not fit your vehicle. Instead, I would recommend looking at the the Hollywood Racks Baja 2 Bike...
    view full answer...

  • If you're looking for a rack that will be used occasionally, there are many racks that would work great for you, including the Thule Passage # TH910XT you mentioned. This type of rack uses a 6 strap/buckle/hook arrangement to attach to the vehicle. The attachment system works pretty well, but it's not very quick, easy or convenient. The Thule Raceway 2, part # TH9001PRO uses 4 attachment cables that retract with a twist of a knob, which allows the rack to be installed or removed...
    view full answer...

  • The Thule Archway trunk mount bike rack # TH9010XT will fit your 2002 Nissan Xterra. The rack uses 6 straps to secure to the back of the vehicle. The initial set up will take the longest but after that it should only take a few minutes to get the rack on and probably half that time to remove it. But for the fastest and easiest rack to install or remove I recommend the Raceway 3, # TH9002PRO. I own this rack myself and it is the easiest rack I have used to install or remove....
    view full answer...

  • The SQRS Quick-Release, 2-Piece, Rooftop Bike Carrier, # RBC012 is designed to specifically fit the Rhino-Rack Aero/Sportz Crossbars and also happens to fit Rola crossbars. But this rack is not designed to fit the factory crossbars on a 2002 Nissan Xterra. But not to worry because there are bike racks that are a direct fit. You can use the following racks from Yakima: FrontLoader, # Y02103 ForkLift, # Y02098 Raptor Aero, # Y02093 And from Thule you can use: Sidearm,...
    view full answer...

  • There are 10 Thule trunk mount bike racks that will fit your 2002 Nissan Xterra: Passage 2, # TH910XT Passage 3, # TH911XT Gateway 2, # TH9006XT Gateway 3, # TH9007XT Archway 2, # TH9009XT Archway 3, # TH9010XT Raceway 2, # TH9001PRO Raceway 3, # TH9002PRO Raceway Platform, # TH9003PRO On own the 3-bike Raceway, # TH9002PRO and is it by far the easiest to use trunk mount bike rack I have come across. The 4 retractable cables make installation quick and easy. This...
    view full answer...








Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com