# 1
Thule Passage Trunk Bike Rack for 2 Bikes - Hanging Style
The rack works very well with our 2019 Dodge Durango. Quality construction, and it was easy to put together and install. The manual was good, and includes a vehicle fit guide with notes specific to the vehicle. The guide recommended using a setting of 11 for the arms, due to the trim package on our vehicle I changed it to 10 and that worked perfectly. Definitely recommend the bike rack!
Positive: The product is well thought out and works for a wide range of automotive vehicles. It comes with interesting dampers that i think work. Instructions seem to be translated from another language, but are quite good, accompanying pictures make installation straightforward. A test drive over speed bumps shows that the rack will support the bike for all travel needs. It can be disassembled , collapsed and stored in the trunk. Downside: The rack is made for the classic triangular shaped frame: horizontal cross bar, "male" bike. For bikes without the horizontal bar, mounting is a little less satisfactory. Such a bike can only be mounted on the outside mounts. Cannot use the damper on one side. Picture shows the mounting. as to a design solution, maybe brackets could be replaced with smaller profile, some adjustability? however, as it is, vibration control is good and adjustability with smaller profile would have vibration concerns.
# 2
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 3
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
I own a 2005 Jeep Wrangler X with 31x10.5x15 oversized tires and wheels. I installed B6196001 HighRock 4x4 Oversize Tire Carrier by Bestop to carry larger spare tire. I needed a bike carrier that would carry our two crusier bikes and clear my spare tire. After measuring, I ordered: -> S64650 - Swagman 2-bike carrier -> 80300 - 7" Hitch Adapter 2" to 1-1/4" Trailer Hitch Receiver -> RM-061 - Roadmaster Quiet Hitch for 2" Trailer Hitches Our order arrived very quickly, etrailer.com upgraded the shipping. All these products arrived well packaged and without damage. In 15 minutes I had every thing assembled, installed on my Jeep and bikes loaded. The bike carrier is very well constructed, finish is excellent and easy to adjust. When adjusting wheel loops and loading bikes, make sure you pay attention to bike pedal position. I chose this extension because I did not want to use the adapter that comes with the bike carrier, I wanted as few parts as possible to keep rattles to a minimum and gives me more options for towing. The anti-rattle bolt/pin firmly secures the bike carrier to the extension and the Roadmaster Quiet Hitch keeps the extension adapter from rattling in the receiver. Road tested approximately 25 miles over rough city roads ( including railroad tracks ), county roads and highway. Bikes traveled very well without any rattles. I can remove my complete setup quickly, fold and put in rear of Jeep if desired. I am very well pleased with my purchase. Note to etrailer: Please consider offering Roadmaster Quiet Hitch in black to match receiver and accessories. Paul In the Land of Oz . . . Just South of the Yellow Brick Road!
# 4
Kuat NV 2.0 Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Gunmetal Gray
This thing is built like a tank! It is of the best fit and funtion I have seen in a bike rack! Solid as can be, fits my bikes perfectly and looks awesome! Plus it folds completely out of the way to access the rear liftgate on my 2022 Rav4!
Great service from etrailer and the rack arrived as expected. Fairly easy assembly. OK video on Kuat’s site, but didn’t cover the foot pedal. Really glad we got the 2” hitch. It tightened up and we’re impressed with the quality and the stability of the rack. We haven’t done a road test yet, but look forward to putting it to the test. We have a Ford F-150 and it works great. The bikes were fairly easy to load with the batteries out and two people. We do need the strap extenders for our RadMini Step Thru’s. The tires are too big for the ones that come with. Only one set of extenders came with the bike and one adapter for a smaller tire. It’s okay, but since it’s a two bike unit, would have been nice to have both extenders. Otherwise, we are really liking the look and stability.
# 5
Swagman Chinook Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
Highly recommend the Swagman Chinook Bike Rack! I have been using mine regularly during the last year and have had no issues. It's easy to attach and remove from my Honda CR-V. It's very sturdy and doesn't shift or 'bounce' around when I'm driving.
Truly grooving on my wife's new Swagman Chinook bike rack. She wanted to be able to transport her nice road bike easily without throwing it in the back of her car, and since a roof rack is out of the question, this Swagman model fit the bill perfectly. It arrived quickly on the anticipated date. Kudos to etrailer.com for the email updates to keep me informed of my purchase. Within one hour, it was installed on my wife's 2014 Mazda3 hatchback. The Swagman is heavy and solid, which is reassuring as it makes me feel confident that it will keep the bikes secure. It also makes me feel like I got my money's worth. A ratchet wrench and Phillip's head screwdriver were the only tools required for the easy install. I did my research before purchasing the Chinook model as I was also eyeballing a very similar Thule rack that was slightly more expensive. I spoke with an etrailer.com expert who gave me the lowdown on both models. Ultimately, the Swagman won out because it has a smaller 'footprint' while extended or folded up ... and also can tilt away from the car for easy access to the hatchback area. Very convenient! FYI: Mazda doesn't make a trailer hitch for the Mazda3 as it's a small car with a small engine and has no business towing anything. Thankfully, the Curt company makes an aftermarket frame and trailer hitch that fits the Mazda3 hatchback perfectly with no drilling. Stupidly, I purchased it from another online company thinking I was getting a good deal. Turns out etrailer.com had it for less with FREE shipping. Oh well ... live and learn. Now I know that etrailer.com is one-stop shopping for bike racks AND trailer hitches. (Full disclosure: I had the garage down the street install the frame as it's easier with a lift) Only snafu: the shipment contained an extra set of keys that I assumed was for the hitch bolt lock (there was also a set of keys on the bolt itself). I spent 15 minutes using those keys trying to figure out how to remove the lock from the bolt to install it on the hitch. The keys just wouldn't turn in the lock. I called etrailer.com and Kevin told me to try the other set of keys ... and they worked. So an extra set of keys came with it that did absolutely nothing ... weird! Obviously, I can't speak to the longevity and durability of the Swagman Chinook 2 Bike Platform Rack as I just installed it. What I can speak to is the sturdiness of it, the ease of the installation and my complete satisfaction with the good folks at etrailer.com.
# 6
RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
I ordered this on May 31st and finally got it on August 11th. We have two eBikes and the load capacity and tilt and swing functions made this rack the best one for our Rav 4 with spare tire on back. RockytMounts had to go into another production cycle before I could get it. But, totally worth the wait. eTrailer honored the original price on my original order and so I saved $xxx on the $xxx full price. The rack construction seems very strong while I was mounting it to my Rav 4. The mounting locks did seem a bit "cheesy" though, as they are made of plastic. But, of course, one never leaves bikes for very long where "evil" lurks! I haven't yet put the bikes on the rack but, if there are problems, I will update this review.
Best bike rack ever! We received our bike rack in record time, earlier than scheduled, and in time for our trip! Love the fact that not only does it hold the bike down on the wheel and not my frame, but it drops down AND swings away for full access to our 2018 Mercedes Sprinter with the barn doors. The doors can swing all the way open and hold in place as designed, so we have a complete view out the back of our van without any obstruction whatsoever. This thing is solid, and it does not budge, we know because we watched it through our camera as we drove down the road. A great investment if you have bikes you want to protect from any damage or theft, as there is also a lock and cable that goes through the bike and also locks the rack to the hitch. Fantastic customer service from etrailer as well!
# 7
Saris Freedom Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
I had to put my electric bikes into this rack, backwards, to make them fit. Not ideal, but it works.The receiving 'trays' that are intended to provide support for holding the bikes, by being placed under the bike tires, are forced to be moved to a location that is not directly under the bottom of the bike tires. While it works in this manner, it is not ideal.For the support that attaches to the diagonal bike frame, we had to remove it from the vertical rail of the rack. We reinstalled it, upside down, because that's the only way we could make it fit, or 'grab', the bike frame. Again, we made it work, but it's not ideal. We chose to keep the rack because it was so much less expensive than the Thule rack we considered buying. The bike shop owner didn't agree with us. He observed that we are putting $3000 worth of bikes on the rack and risking that investment. So far, no problems, other than the ill-fitting installation.
With a few adjustments this rack has delivered. Needed to add additional strapping since the provide straps for securing the bikes to center bar were not long enough due to my ebike design (Velotric). My bikes are step through with a thick frame so provided straps won't fit. Simple adjustment with strapping resolved minor issue. Speed of 73 mph on the highway and some bumpy VT roads and this rack performed.
# 8
Swagman Trailhead Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Tilting
etrailer has the best pre- and post-sales customer service I've ever seen! I started out not knowing anything about hitch-mounted racks. So I wrote to etrailer telling them about my car and type of hitch I was about to have installed. Samuel wrote back with lots of great information tailored specifically to my car. He even included a photo that looked just like my 2017 white VW GTI with a hitch and rack installed. Okay something of a coincidence. But the rest of the assistance I got from the crew at etrailer was just as prophetic. I went into this a novice and came out knowing lots more about hitches and racks and finding the rack best suited to my situation. I have a small car, a class 1 hitch and a heavy mountain bike. I got exactly what I needed. As to the Swagman rack itself, it works fine. If I had a different situation I would probably buy a platform rack as they are easier to load. There's no reason to buy a bike rack anywhere else.
First off, thanks to Jason T. or "Troop". The exemplary customer service he provided is rare these days. Troop made several calls to the various manufacturers to ascertain which bike rack would afford me the most ground clearance as my new VW Golf sits low to the ground and my old bike rack frequently scraped the ground when I went up even a slight up hill grade. His efforts paid off as he found me the best bike rack for my car, the Swagman Trailhead 2 Bike Carrier. It sits up off the ground just high enough that it doesn't scrape on my driveway. It is also sturdy and holds my bikes securely. And, the delivery was amazingly fast. I had my rack in about 2 days! Note to Troop, see my Pittsburgh Pirates Logo on my bumper in the attached pictures? Pirate Fans persevere! The Bucco's will be coming after your Cardinals this year! Thanks again Troop!
# 9
Kuat NV 2.0 Base Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount - Matte Black
I've taken this rack all over New England on the front of my Dodge Ram 3500 pick up truck with a truck camper. I had no idea it was possible to love a bike rack so much. After one drive I didn't ever worry about it again. So nice that it locks up when I am camping or taking a quick stop for food on the road. So glad I bought it from etrailer. They totally help me pick the perfect rack for my challenging set up.
Still very new, but what an awesome bike rack! Assembly was a snap and the rack is rock-solid when you secure it to the hitch receiver. etrailer was amazing too - excellent communication, price and fast, free delivery. Overall I am extremely happy with the rack and service!
# 10
Thule EasyFold XT Bike Rack for 2 Electric Bikes - 1-1/4" and 2" Hitches - Frame Mount
I purchased the rack and receiver hitch a year ago. Installation of the rack was made simple with the installation video that was specific to my vehicle (2020 Honda Accord). Literally took less than an hour start to finish. Only tool that I needed to buy was a torque wrench, which was about 20 bucks. It did require a very small cut in the plastic bumper that was accomplished easily with a keyhole saw. There was no drilling or other significant issues. The rack itself is awesome! My wife and I have two Lectric XP3 bikes. They weigh about 65 pounds each with battery. When we travel I revome the batteries to save a bit of weight. I have made two cross country trips (over 6000 miles) with this rack and have never had an issue. Literally every gas stop or hotel stop someone asks me about the rack and bikes. It really is that nice. My wife usually scolds me because we lose a 1/2 hour of travel time each stop to visit with complete strangers:) The rack is easy to install and remove on the receiver hitch. The lockout feature works great and gives a great deal of peace of mind. The bikes are easy to load. I don't use it, but there is a ramp that could make loading the bikes easier if a person couldn't lift the bike onto the rack. There are two arms the lock onto the frame of the bikes similar to the receiver hitch. Once locked down the bikes will not move. I would recommend ordering the longer ratchet staps if you have fat tires. I think they cost around 20 bucks but the longer straps allow for a little more flexibility in arranging bikes on the rack. I would strongly recommend this product and this company.
This product arrived in perfect condition in a sturdy box and arrived as expected. The description and photo were perfect. I am only 4'11" and I can lift and put this carrier on the hitch on our vehicle. It folds up which makes it easy to install. My husband did the minor assembly. We are impressed with how securely the rack is and comes with a ramp to help ease the bike onto the rack without lifting. Also, the rack can be tilted so the back hatch of the vehicle can be accessed without taking off the rack from the car.
# 11
Yakima HoldUp Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount
Works well for transporting two 29" wheeled mountain bikes. However, after one year it's starting to rust in several areas (see attached photos), and the front wheel arms are becoming increasingly difficult to raise and lower. Finally the locking cable is extremely rusty as you can see in the attached photo. I'm not sure how durable this rack will be long term.
Sturdy, locking pin tightens to dampen sway.
# 12
Curt 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Frame Mount - Tilting
I installed this rack onto a Curt trailer hitch which is mounted onto a 2017 Honda Fit. I have been using it intermittently for several months, probably about 5 times with one bike and twice with two bikes. I give some pros and cons below and then elaborate. Pros: easy to assemble, easy to mount and dismount bikes, easy to lock and unlock, how to put the rack into different positions is intuitive Cons: inconvenient to put the rack into different positions, inconvenient to mount the rack onto the hitch, rack protrudes about 15 inches from bumper when in flipped up position (seems very vulnerable to someone backing into it in a parking lot, very inelegant looking I say the repositioning is intuitive because there is really only one way you could possibly place the pins for each position. But removing and replacing two pins is much less convenient than turning a knob or a lever, like some racks do. Also many racks fold and flip in such a way as to look very unobtrusive when in non-use mode. This one looks like kind of a monstrosity. That does not really bother me but it might bother some owners. The part that does bother me is how far it protrudes from the car. I back into parking spaces whenever possible to avoid someone bumping into the rack and damaging it (which happened to a friend). My number one suggestion for Curt is related to mounting the rack onto the hitch. Make it easier to tell when the holes are lined up so that the bolt/pin will fit and thread. As it is now, if you insert the rack as far as it can go it is way too far in. Ideally, it would be exactly lined up. Failing that, maybe some kind of click or other feedback to know at least that you are in the neighborhood. It would also be great to have an attaching device that is easier to fasten and unfasten than is the bolt/pin. Tip for mounting the rack onto the hitch: I assumed that it would be awkward to hold, what is it 46 pounds?, while trying to line up the rack probe with the receiver. If you have a garage with exposed collar ties, my solution could work well for you. I looped a cargo strap over a collar tie. Then I hooked both hooks of a bungie onto that loop. The idea is that you hook one of the bike frame holders of the rack onto the bungie, suspending the rack a few inches off the garage floor. This takes most of the weight of the rack so that you can just pull up or down and forward until you line up with the receiver. Tip for mounting bikes. Don't put the little screw into the post that prevents you from completely removing the bike frame holders. Remove both holders. Position the first bike, slide the holder into place, position the second bike, slide the holder into place. I found this makes it much easier, because you avoid parts of the bike hitting the holder as you are trying to get the wheels into place. The trick is that if you are mounting only one bike, don't forget to put the second holder back on - or maybe just stick it inside the car right away.
I had a 1 1/4" hitch installed on my 2016 toyota camry (the only size offered on the camry). I was very pleased with the ride. I expected to hear alot of noise like experienced when towing a trailer, but I heard almost nothing accept when going over speed bumps. I had to extend the tire supports to their widest position because having mountain bikes with a step through angled bar, they were more secure the closer i could get the upper and lower support arms to the seat post. The bikes were mounted in opposite directions and only stuck out maybe 6 inches or so. One locking barrel on the lower support arm was malfunctioning and gave me trouble but i called etrailer and they sent a replacement as soon as they were in stock. It comes with a anti rattle hitch pin but I highly recommend purchasing an anti rattle hitch pin with a lock on the end instead of just a clip for more security when unattended. After a few times mounting the bikes and figuring out the best way they should be positioned (pedals positions, direction of bike, and that my wife's smaller bike fit better going on first with my larger bike on the outside) I can mount the rack and bikes and be ready to go in just 5 minutes. (70 pounds on a torque wrench recommended for the hitch pin) I am overall pleased with my purchase i would recommend this product.
What our customers are saying:
"I purchased a hitch, wiring harness, bike carrier and bike adapter for a newly redesigned 2007 Hyundai Santa Fe. Everything arrived in a matter of days and either fit or worked perfectly. Great prices, quality and service support. Rest assured, I'll be recommending you to anyone who asks. Thanks again."