# 1
Curt Tri-Ball Mount - 3 Chrome Balls - 10,000 lbs
definitely solid as a rock
Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 3
Curt Multi-Ball Mount for 2" Hitches - Solid, Black Powder Coated Shank - Black Balls
Functionally, this hitch has been great with no issues to date. Aesthetically, the black color did quickly fade to a gray color within a couple of months. Ball surface also presented rust after very minimal use. That being said, I did buy a hitch to tow trailers, not look pretty.
Weights a ton. Seems very strong...10,000 pounds using the 2 5/16s balls. Good paint.
# 4
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount. The service has been outstanding. This is the place to go.
# 5
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 6
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 7
Curt Class II Euro Style Drawbar with 2" Ball - 3-1/8" Rise - 3,500 lbs
Incorrectly listed on etrailers as a 3-1/8” rise, when really this is a 5-1/8” rise (marked correctly on the item itself, but listed incorrectly on this website).
I am completely satisfied with the product. Great quality and excellent finish. Prompt shipping and excellent customer service. It is stylish and functional and will meet my needs for towing up to 3,500 pounds. I would definitely do business with this company again!!!
# 8
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
I have a custom made tow guard. The ball mount I have was too short to allow me to attach the tow guard to my new truck. I searched the web and found just what I needed at etrailer.com. It's the only site I found that carried the size I needed. The product fits my needs perfectly. I can now protect my boat from rocks and other road debris when towing. Thank you etrailer.com.
# 9
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
Works perfectly. Fast shipping. Very Satisfied.
Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .
# 10
Flash Silent Adjustable 2-Ball Mount w Chrome Balls - 2" Hitch - 8" Drop, 9" Rise
Great looking adjustable hitch. I purchased the non-locking version because locks and similar mechanisms seem to have issues due to salt and ice here in MN. Not sure if the locking version would have issues, but I didn't want to take the chance. Hitch is easy to adjust, seems very strong, and looks great.
This hitch rocks! All you need, looks good, performs excellent BOOM! Thanks etrailer
# 11
Pro Series Tri-Ball Mount for 2" Hitches - 1-7/8", 2", 2-5/16" Balls - Black
Not only did I get the parts I needed at a great price. They were delivered they day after I ordered them. Great communication from my salesman. I will definitely be a return customer.
Heavy duty hitch. Well built and welds are fine.
# 12
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 13
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Needed a large drop hitch to pull my car trailer. This item came quickly and worked perfectly.
This extreme rise ball mount is what I need to make my passenger car into a back-up trailer puller. It is well built and has a welded strut to reinforce the long rise/drop ball mount. The "shock damper" feature is sure to help absorb the leverage movement that a rise/drop ball mount passes on to the hitch receiver itself.
# 14
Curt Pintle Hook with 2-5/16" Ball - 2" Hitches - 12,000 lbs/16,000 lbs
The customer service and the timeliness in which l have received my orders from etrailer.com is second to none. I needed my hitch to arrive on time so I could pick up a nice chunk of Sycamore. A bit of electrical tape on the shaft to eliminate "play" in the receiver, slip in the new lockable SS pin from Bulldog and off we went to pick up my prize! What a great company to do business with!
Solid 2-5/16" hitch. The recesses let water by so the hitch won't rust up in your receiver hitch and will be easy to get out. I bought this as a spare, but after receiving it, I will be using it as my primary hitch. I originally bought it to put in my trailer spotter on my skidsteer to move trailers around without having to swap the original hitch from the truck.
# 15
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
# 16
Brophy Ball Mount - 5" Rise, 6" Drop - 16" Long - Aluminum - 8,000 lbs
Perfect for my Tahoe. I have a 2019 Tahoe LS 4x4 with the max tow package. The receiver is mounted higher than than on the truck it replaced. Six inches of drop appears to be just about right for my boat trailer.
I bought a new trailer that came with a tongue mounted jack stand. The problem was the hand crank was to close my truck and prevented me from lowering my tailgate while the trailer was connected, by about a 1/2 inch. I had a standard steel 6 inch drop Reece ball mount. This one has more weight capacity, but is half the weight of the older ball mount. It added just enough distance from the truck I can put the tailgate down!
# 17
Curt Ball Mount for 2" Hitches - 6-1/4" Rise, 7-1/2" Drop - 13" Long - 5,000 lbs
It is a Receiver!
The box it was shipped in had a hole in it, so the mount slipped out of the box when it was delivered. There was some minor paint damage from that, but the mount itself seems fine.
# 18
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 19
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 20
Curt Multi-Ball Mount w/ Tow Hook for 2" Hitches
Cool to follow up on your product. The multi-ball works as it should. I bought it since I didn't know if the trailer I would get would be 2" or 2 1/4. I tow a 4,000 # trailer/race car with it. It's a heavy piece to carry around, but I feel that it will last a good many years. I did make a spacer to cram into the receiver, so the hitch doesn't rattle as much. Otherwise it's great. Tim E.
the packaging showed up as a mess, need to see if its damaged when I open it
Convert-A-Ball Ball Mount with 4 Inch Drop Review - 2013 Kia Sorento
Today on our 2013 Kia Sorrento well be test fitting the Convert-a-ball cushion ball mount for two inch hitches, part number AMSC4. Before we begin our test fit well first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our measurement is 13 inches. Now well go ahead and slide the shank of the ball mount into the opening of the hitch, line up our pin holes, and secure it with a pin and clip. Well then measure from the ground to the top of the ball platform and get a measurement of 8 inches.
Draw-Tite Ball Mount Review - 2013 Kia Sorento
Today on our 2013 Kia Sorento well be test fitting the Draw Tite ball mount with three-quarter inch rise or two inch drop, rated at 6,000 pounds, part number 2923. Now, before we begin our installation well need to get our hitch height measurement. To get this measurement well measure from the ground to the top of the receiver tube opening. On this vehicle it is 12 inches. Now keep in mind this measurement can change depending on hitch style, tire size or any other accessory that may change your vehicles ride height. Its a good idea to go ahead and measure yours first.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."